Biomanufacturing evolution from conventional to intensified processes for productivity improvement: a case study

Integrated continuous downstream process of monoclonal antibody developed by converting the batch platform process based on the process characterization

A continuous downstream process of monoclonal antibody was developed based on the process characterization. Periodic-counter current chromatography (PCCC) with two protein A columns was used for the capture step. For low pH virus inactivation (VI), a batch reactor was employed, which can work as a surge (buffer) tank. Flow-through chromatography (FTC) with two connected columns of different separation modes (anion-mixed mode and cation exchange) was designed as a polish step. After 24 h PCCC run, the collected pool was processed for VI. After adjusting pH and electric conductivity, the solution was fed to the two connected FTC columns for 24 h. Virus filter was also connected to the exit of the connected-column. PCCC and FTC were run in parallel. Six runs of different feed rates (0.5-10 L/day) and feed concentrations (1-3.2 g/L) were performed with protein A columns of 1-5 mL and FTC columns of 3-10 mL. The largest run (feed rate 10 L/day, feed concentration 2 g/L) was carried out at a GMP facility with 15 mL protein A columns and 100 mL FTC columns. Good recovery and purity values were obtained for all runs. The process was found to be flexible and stable for feed fluctuations. Only three surge or pool tanks were needed in addition to the final product pool tank.

Host cell proteins in monoclonal antibody processing: Control, detection, and removal

Host cell proteins (HCPs) are process-related impurities in a therapeutic protein expressed using cell culture technology. This review presents biopharmaceutical industry trends in terms of both HCPs in the bioprocessing of monoclonal antibodies (mAbs) and the capabilities for HCP clearance by downstream unit operations. A comprehensive assessment of currently implemented and emerging technologies in the manufacturing processes with extensive references was performed. Meta-analyses of published downstream data were conducted to identify trends. Improved analytical methods and understanding of "high-risk" HCPs lead to more robust manufacturing processes and higher-quality therapeutics. The trend of higher cell density cultures leads to both higher mAb expression and higher HCP levels. However, HCP levels can be significantly reduced with improvements in operations, resulting in similar concentrations of approx. 10 ppm HCPs. There are no differences in the performance of HCP clearance between recent enhanced downstream operations and traditional batch processing. This review includes best practices for developing improved processes.

Comparative Approaches for Quantification of Product Yield in a Model Recombinant Green Fluorescent Protein Expressed in E. coli

Process Analytical Technologies (PAT) used to monitor and control manufacturing processes are crucial for efficient and automated bioprocessing, which is in congruence with lights-off-manufacturing and Industry 4.0 initiatives. As biomanufacturing seeks to realize more high-throughput and automated operation, an increasing need for multimodal analysis of process metrics becomes essential. Herein, we detail a series of methods for analyzing product yield from a bioreactor and how to conduct cross-method comparisons. We employ a model system of Escherichia coli (E. coli) expression of green fluorescent protein (GFP), which is a simple, cost effective model for students and educators to replicate at different scales. GFP is an ideal analytical marker as it is easy to visualize due to its fluorescence which indicates cellular protein expression, cell localization and physiological changes of the cell population. In this study, samples from a 300 L bioreactor with GFP-expressing E. coli are analyzed to improve product yield and bioprocessing efficiency. Utilizing a fed-batch process for enhanced cell density and product titer, this bioreactor runs on a 24-hour schedule from inoculation to GFP induction and final harvest. To reliably quantify relative GFP expression and E. coli proliferation, we provide simple protocols and example results for comparing three different analytical methods: (1) in-line bioreactor measurements, (2) plate reader assays, and (3) microscopy. The GFP and cell density results follow similar trends based on the various inline and offline analytical methods and show a peak of GFP expression and cell density between 12.5 and 18 hours post inoculation.

Biocatalyst for the synthesis of natural flavouring compounds as food additives: Bridging the gap for a more sustainable industrial future

Biocatalysis entails the use of purified enzymes in the manufacturing of flavouring chemicals food industry as well as at the laboratory level. These biocatalysts can significantly accelerate organic chemical processes and improve product stereospecificity. The unique characteristics of biocatalyst helpful in synthesizing the environmentally friendly flavour and aroma compounds used as a food additive in foodstuffs. With methods like enzyme engineering on biotechnological interventions the efficient tuning of produce will fulfil the needs of food industry. This review summarizes the biosynthesis of different flavour and aroma component through microbial catalysts and using advanced techniques which are available for enzyme improvement. Also pointing out their benefits and drawbacks for specific technological processes necessary for successful industrial application of biocatalysts. The article covers the market scenario, cost economics, environmental safety and regulatory framework for the production of food flavoured chemicals by the bioprocess engineering.

Advanced control strategies for continuous capture of monoclonal antibodies based upon biolayer interferometry

The semi and fully continuous production of monoclonal antibodies (mAbs) has been gaining traction as a lower cost, and efficient production of mAbs to broaden patient access. To be truly flexible and adaptive to process demands, the industry has lacked sufficient advanced control strategies. The variation of the upstream product concentration typically cannot be handled by the downstream capture step, which is configured for a constant feed concentration and fixed binding capacity. This inflexibility leads to losses of efficiency and product yield. This study shows that these challenges can be overcome by a novel advanced control strategy concept that includes dynamic control throughout a perfusion bioreactor, with cell retention by alternating tangential flow, integrated with simulated moving bed (SMB) multi-column chromatography. The automation workflow and advanced control strategy were implemented through the use of a visual programming development environment. This enabled dynamic flow control across the upstream and downstream process integrated with a dynamic column loading of the SMB. A sensor prototype, based on continuous biolayer interferometry measurements was applied to detect mAb breakthrough within the last column flow-through to manage column switching. This novel approach provided higher specificity and lower background signal compared to commonly used spectroscopy methods, resulting in an optimized resin utilization while simultaneously avoiding product loss. The dynamic loading was found to provide a twofold increase of the mAb concentration in the eluate compared to a conservative approach with a predefined recipe with similar impurity removal. This concept shows that advanced control strategies can lead to significant process efficiency and yield improvement.

Developing an ultra-intensified fed-batch cell culture process with greatly improved performance and productivity

Intensified fed-batch (IFB), a popular cell culture intensification strategy, has been widely used for productivity improvement through high density inoculation followed by fed-batch cultivation. However, such an intensification strategy may counterproductively induce rapidly progressing cell apoptosis and difficult-to-sustain productivity. To improve culture performance, we developed a novel cell culture process intermittent-perfusion fed-batch (IPFB) which incorporates one single or multiple cycles of intermittent perfusion during an IFB process for better sustained cellular and metabolic behaviors and notably improved productivity. Unlike continuous perfusion or other semi-continuous processes such as hybrid perfusion fed-batch with only early-stage perfusion, IPFB applies limited times of intermittent perfusion in the mid-to-late stage of production and still inherits bolus feedings on nonperfusion days as in a fed-batch culture. Compared to IFB, an average titer increase of ~45% was obtained in eight recombinant CHO cell lines studied. Beyond IPFB, ultra-intensified IPFB (UI-IPFB) was designed with a markedly elevated seeding density of 20-80 × 106 cell/mL, achieved through the conventional alternating tangential flow filtration (ATF) perfusion expansion followed with a cell culture concentration step using the same ATF system. With UI-IPFB, up to ~6 folds of traditional fed-batch and ~3 folds of IFB productivity were achieved. Furthermore, the application grounded in these two novel processes showed broad-based feasibility in multiple cell lines and products of interest, and was proven to be effective in cost of goods reduction and readily scalable to a larger scale in existing facilities.

Evaluation of a single-use disk stack centrifuge for improved efficiency and sustainability at 1000 L GMP manufacturing scale

Direct depth filtration is an established technology for single-use harvest operation. Advantages of direct depth filtration include familiarity with depth filtration in downstream processes and simplicity of the operation. Drawbacks include low capacity, large footprint, labor-intensive set-up, high water use, and high waste in the form of discarded filters. Single-use centrifugation is emerging as an alternative to depth filtration for the single-use harvest step. Within the single-use centrifugation space, disc stack centrifugation represents the newest entrant. In this study, we evaluated the performance of the GEA kytero single-use disc stack centrifuge to clarify two monoclonal antibody-producing cell culture fluids. The separation performance of the GEA kytero centrifuge varied between the two cell culture fluids, with differences in centrate turbidity and centrate filterability measured. A comparison was then performed to determine resource savings, compared to direct two-stage depth filtration, when using a GEA kytero centrifuge to harvest a 1000 L bioreactor. The analysis concluded that replacement of the first stage of depth filters with a GEA kytero centrifuge has the potential to decrease the required second stage depth filtration area by up to 80%. The decrease in depth filter area resulting from the use of the GEA kytero would result in a decrease in the harvest step footprint, a decrease in buffer volume required to prime and rinse depth filters, and a decrease in the volume of plastic waste. An economic comparison of the GEA kytero single-use centrifuge against a direct depth filtration step found that for a 1000 L harvest step, the GEA kytero centrifuge may reduce costs by up to 20% compared with two-stage direct depth filtration.

Risk assessment for biopharmaceutical single-use manufacturing: A case study of upstream continuous processing

In the current transition to intensified upstream processing, the risks of adopting traditional single-use systems for high-titer, long-duration perfusion cultures, have thus far not been considered. This case study uses the Failure Modes and Effects Analysis (FMEA) method to evaluate the risks associated with implementing upstream single-use technology. The simulated model process was used to compare the risk level of single-use technology for a traditional fed-batch cell culture with that for perfusion culture, under the same annual protein production conditions. To provide a reasonable source of potential risk for FMEA, all single-use upstream operations for both fed-batch and perfusion processes were investigated using an analytical method developed to quantify the impact of process parameters and operating conditions on single-use system specifications and to ensure objectivity. Many of the risks and their levels, were similar in long-duration perfusion cultures and fed-batch cultures. However, differences were observed for high-risk components such as daily sampling and installation. The result of this analysis indicates that the reasons for risk are different for fed-batch cultures and perfusion cultures such as larger bioreactors in fed-batch and longer runs in perfusion, respectively. This risk assessment method could identify additional control measures and be part of a holistic contamination control strategy and help visualize their effectiveness.

Efficient optimization of time-varying inputs in a fed-batch cell culture process using design of dynamic experiments

In cell culture process development, we rely largely on an iterative, one-factor-at-a-time procedure based on experiments that explore a limited process space. Design of experiments (DoE) addresses this issue by allowing us to analyze the effects of process inputs on process responses systematically and efficiently. However, DoE cannot be applied directly to study time-varying process inputs unless an impractically large number of bioreactors is used. Here, we adopt the methodology of design of dynamic experiments (DoDE) and incorporate dynamic feeding profiles efficiently in late-stage process development of the manufacture of therapeutic monoclonal antibodies. We found that, for the specific cell line used in this article, (1) not only can we estimate the effect of nutrient feed amount on various product attributes, but we can also estimate the effect, develop a statistical model, and use the model to optimize the slope of time-trended feed rates; (2) in addition to the slope, higher-order dynamic characteristics of time-trended feed rates can be incorporated in the design but do not have any significant effect on the responses we measured. Based on the DoDE data, we developed a statistical model and used the model to optimize several process conditions. Our effort resulted in a tangible improvement in productivity-compared with the baseline process without dynamic feeding, this optimized process in a 200-L batch achieved a 27% increase in titer and > 92% viability. We anticipate our application of DoDE to be a starting point for more efficient workflows to optimize dynamic process conditions in process development.

Automated Raman feed-back control of multiple supplemental feeds to enable an intensified high inoculation density fed-batch platform process

Biologics manufacturing is increasingly moving toward intensified processes that require novel control strategies in order to achieve higher titers in shorter periods of time compared to traditional fed-batch cultures. In order to implement these strategies for intensified processes, continuous process monitoring is often required. To this end, inline Raman spectroscopy was used to develop partial least squares models to monitor changes in residual concentrations of glucose, phenylalanine and methionine during the culture of five different glutamine synthetase piggyBac® Chinese hamster ovary clones cultured using an intensified high inoculation density fed-batch platform process. Continuous monitoring of residual metabolite concentrations facilitated automated feed-rate adjustment of three supplemental feeds to maintain glucose, phenylalanine, and methionine at desired setpoints, while maintaining other nutrient concentrations at acceptable levels across all clones cultured on the high inoculation density platform process. Furthermore, all clones cultured on this process achieved high viable cell concentrations over the course of culture, indicating no detrimental impacts from the proposed feeding strategy. Finally, the automated control strategy sustained cultures inoculated at high cell densities to achieve product concentrations between 5 and 8.3 g/L over the course of 12 days of culture.

An adaptive modeling approach using spiking-augmentation method to improve chemometric model performance in bioprocess monitoring

Intensified and continuous processes require fast and robust methods and technologies to monitor product titer for faster analytical turnaround time, process monitoring, and process control. The current titer measurements are mostly offline chromatography-based methods which may take hours or even days to get the results back from the analytical labs. Thus, offline methods will not meet the requirement of real time titer measurements for continuous production and capture processes. FTIR and chemometric based multivariate modeling are promising tools for real time titer monitoring in clarified bulk (CB) harvests and perfusate lines. However, empirical models are known to be vulnerable to unseen variability, specifically a FTIR chemometric titer model trained on a given biological molecule and process conditions often fails to provide accurate predictions of titer in another molecule under different process conditions. In this study, we developed an adaptive modeling strategy: the model was initially built using a calibration set of available perfusate and CB samples and then updated by augmenting spiking samples of the new molecules to the calibration set to make the model robust against perfusate or CB harvest of the new molecule. This strategy substantially improved the model performance and significantly reduced the modeling effort for new molecules.

Reducing biopharmaceutical manufacturing costs through continuous processing in a flexible J.POD facility

In this work, process models were developed to capture the impact of biomanufacturing costs on a commercial scale and emphasize the way in which facility design and operation must balance meeting product demand while minimizing production costs. Using a scenario-based modeling approach, several facility design strategies were evaluated, including a traditional large stainless-steel facility and a small footprint, portable-on-demand (POD)-based facility. Bioprocessing platforms were compared by estimating their total production costs across different facility types and specifically illustrating how continuous bioprocessing has gained in popularity as a novel and cost-effective approach to manufacture high-quality biopharmaceuticals. The analysis showed how fluctuations in market demand have a dramatic effect on manufacturing costs and plant utilization, with far-reaching implications on the total cost to patients.

Computational framework for the techno-economic analysis of monoclonal antibody capture chromatography platforms

We developed a computational framework that integrates commercial software components to perform customizable technoeconomic feasibility analyses. The use of multiple software packages overcomes the shortcomings of each to provide a detailed simulation that can be used for sensitivity analyses and optimizations. In this paper, the framework was used to evaluate the performance of monoclonal antibody capture processes. To this end, the simulation framework incorporated dynamic models for the affinity chromatography step that were validated with experimental breakthrough curves. The results were integrated with an Intelligen SuperPro Designer process simulation for the evaluation of key performance indicators of the operations. As proof of concept, the framework was used to perform a sensitivity analysis and optimization for a case study in which we sought to compare membrane and resin chromatography for disposable and reusable batch capture platforms. Two membranes and one resin were selected for the capture media, which yielded six process alternatives to compare. The objective functions were set to be cost of goods, process time, and buffer utilization. The results of the optimization of these process alternatives were a set of operating conditions that display tradeoffs between competing objectives. From this application exercise, we conclude that the framework can handle multiple variables and objectives, and it is adaptable to platforms with different chromatography media and operating modes. Additionally, the framework is capable of providing ad hoc analyses for decision making in a specific production context.

Use of Monte Carlo simulations for improved facility fit planning in downstream biomanufacturing and technology transfer

Biologics manufacturing is capital and consumable intensive with need for advanced inventory planning to account for supply chain constraints. Early-stage process design and technology transfer are often challenging due to limited information on process variability regarding bioreactor titer, process yield, and product quality. Monte Carlo (MC) methods offer a stochastic modeling approach for process optimization where probabilities of occurrence for process inputs are incorporated into a deterministic model to simulate more likely scenarios for process outputs. In this study, we explore MC simulation-based design of a monoclonal antibody downstream manufacturing process. We demonstrate that this probabilistic approach offers more representative outcomes over the conventional worst-case approach where the theoretical minimum and maximum values of each process parameter are used without consideration for their probability of occurrence. Our work demonstrates case studies on more practically sizing unit operations to improve consumable utilization, thereby reducing manufacturing costs. We also used MC simulations to minimize process cadence by constraining the number of cycles per unit operation to fit facility preferences. By factoring in process uncertainty, we have implemented MC simulation-based facility fit analyses to efficiently plan for inventory when accounting for process constraints during technology transfer from lab-scale to clinical or commercial manufacturing.

Upstream continuous processing: recent advances in production of biopharmaceuticals and challenges in manufacturing

Upstream continuous processing, or most commonly perfusion processing, for biopharmaceutical production, is emerging as a feasible and viable manufacturing approach. Development in production of recombinant therapeutic proteins as well as viral vectors, vaccines, and cell therapy products, has numerous research publications that came out in previous years. Recent research areas are in perfusion-operation strategies maximizing and controlling bioreactor cell density, adding feed solution designed to supplement basal medium feed stream, combining cell line engineering with bioreactor conditions such as hypoxia, and implementing online process monitoring of cell density by capacitance sensor and metabolites by Raman spectroscopy. Perfusion applications are not limited to production process alone but include other upstream areas where high cell density process is essential such as in cell bank preparation, N-1 seed bioreactor, and combination with intensified fed-batch production process. This review covers recent advances in continuous processing over the last two years for biopharmaceutical production.

Formulation mitigations for particle formation induced by enzymatic hydrolysis of polysorbate 20 in protein-based drug products: insights from a full-factorial longitudinal study

Hydrolytic degradation of the polysorbate 20 (PS20) surfactant in protein-based liquid formulations releases free fatty acids (FFAs), which can accumulate to form particles in drug products during real-time (long-term) storage. To identify formulation conditions that mitigate the risk of particle formation, we conducted a longitudinal study using purified recombinant monoclonal antibody (mAb) formulated in 24 conditions. In this real-time stability study at 5 °C, three key formulation parameters—mAb concentration, initial PS20 concentration, and pH—were varied across representative ranges in a full-factorial design. A longitudinal regression analysis was used to evaluate the effects of these parameters and their interactions on PS20 degradation (via measurements of PS20, FFAs, and PS20 ester distribution) and on particle formation (via visible particle observations and subvisible particle counts). The time-dependent onset of visible particles trended with the rise in subvisible particle counts and FFA levels and fall in PS20 concentration. In the ranges studied here, lower mAb concentration and higher initial PS20 concentration delayed the onset of particles, whereas pH had a negligible effect. These observations were consistent with the general trends predicted by our previously published FFA solubility model. Taken together, these findings highlight the complex relationships between formulation parameters, PS20 degradation, and particle formation.

AAV process intensification by perfusion bioreaction and integrated clarification

Adeno-associated viruses (AAVs) demand for clinical trials and approved therapeutic applications is increasing due to this vector's overall success and potential. The high doses associated with administration strategies challenges bioprocess engineers to develop more efficient technologies and innovative strategies capable of increasing volumetric productivity. In this study, alternating tangential flow (ATF) and Tangential Flow Depth filtration (TFDF) techniques were compared as to their potential for 1) implementing a high-cell-density perfusion process to produce AAV8 using mammalian HEK293 cells and transient transfection, and 2) integrating AAV harvest and clarification units into a single step. On the first topic, the results obtained demonstrate that AAV expression improves with a medium exchange strategy. This was evidenced firstly in the small-scale perfusion-mocking study and later verified in the 2 L bioreactor operated in perfusion mode. Fine-tuning the shear rate in ATF and TFDF proved instrumental in maintaining high cell viabilities and, most importantly, enhancing AAV-specific titers (7.6 × 104 VG/cell), i.e., up to 4-fold compared to non-optimized perfusion cultures and 2-fold compared with batch operation mode. Regarding the second objective, TFDF enabled the highest recovery yields during perfusion-based continuous harvest of extracellular virus and lysate clarification. This study demonstrates that ATF and TFDF techniques have the potential to support the production and continuous harvest of AAV, and enable an integrated clarification procedure, contributing to the simplification of operations and improving manufacturing efficiency.

Antibody charge variant modulation by in vitro enzymatic treatment in different CHO cell cultures

Charge variants represent a critical quality attribute that must be controlled during the development and manufacturing of monoclonal antibodies (mAb). Previously, we reported the development of a cost-effective enzymatic treatment capable of removing the C-terminal lysine from a mAb produced by a Chinese hamster ovary (CHO) GS cell line. This treatment resulted in a significant decrease in basic charge variants and a corresponding improvement in the main peak, enabling a longer cell culture production duration for titer improvement. Here, we describe this enzymatic treatment protocol in detail and demonstrate its applicability to two additional mAbs produced by distinct industrial cell lines. The simple addition of carboxypeptidase B (CpB) at a ratio of 1:10,000 (w/w) to whole cell cultures significantly improved the main peaks for both mAbs without affecting other critical quality attributes, including size exclusion chromatography impurities and N-glycans. Our results demonstrate that this in vitro CpB treatment protocol can be used as a platform strategy to improve main peak for mAbs that exhibit high levels of basic variants attributable to C-terminal lysines. An in vitro enzymatic treatment in general may be another good addition to existing in vivo CHO cell culture strategies for titer improvement and control of critical quality attributes. This article is protected by copyright. All rights reserved.

Improved Titer in Late-Stage Mammalian Cell Culture Manufacturing by Re-Cloning

Improving productivity to reduce the cost of biologics manufacturing and ensure that therapeutics can reach more patients remains a major challenge faced by the biopharmaceutical industry. Chinese hamster ovary (CHO) cell lines are commonly prepared for biomanufacturing by single cell cloning post-transfection and recovery, followed by lead clone screening, generation of a research cell bank (RCB), cell culture process development, and manufacturing of a master cell bank (MCB) to be used in early phase clinical manufacturing. In this study, it was found that an additional round of cloning and clone selection from an established monoclonal RCB or MCB (i.e., re-cloning) significantly improved titer for multiple late phase monoclonal antibody upstream processes. Quality attributes remained comparable between the processes using the parental clones and the re-clones. For two CHO cells expressing different antibodies, the re-clone performance was successfully scaled up at 500-L or at 2000-L bioreactor scales, demonstrating for the first time that the re-clone is suitable for late phase and commercial manufacturing processes for improvement of titer while maintaining comparable product quality to the early phase process.

N-1 Perfusion Platform Development Using a Capacitance Probe for Biomanufacturing

Fed-batch process intensification with a significantly shorter culture duration or higher titer for monoclonal antibody (mAb) production by Chinese hamster ovary (CHO) cells can be achieved by implementing perfusion operation at the N-1 stage for biomanufacturing. N-1 perfusion seed with much higher final viable cell density (VCD) than a conventional N-1 batch seed can be used to significantly increase the inoculation VCD for the subsequent fed-batch production (referred as N stage), which results in a shorter cell growth phase, higher peak VCD, or higher titer. In this report, we incorporated a process analytical technology (PAT) tool into our N-1 perfusion platform, using an in-line capacitance probe to automatically adjust the perfusion rate based on real-time VCD measurements. The capacitance measurements correlated linearly with the offline VCD at all cell densities tested (i.e., up to 130 × 10⁶ cells/mL). Online control of the perfusion rate via the cell-specific perfusion rate (CSPR) decreased media usage by approximately 25% when compared with a platform volume-specific perfusion rate approach and did not lead to any detrimental effects on cell growth. This PAT tool was applied to six mAbs, and a platform CSPR of 0.04 nL/cell/day was selected, which enabled rapid growth and maintenance of high viabilities for four of six cell lines. In addition, small-scale capacitance data were used in the scaling-up of N-1 perfusion processes in the pilot plant and in the GMP manufacturing suite. Implementing a platform approach based on capacitance measurements to control perfusion rates led to efficient process development of perfusion N-1 for supporting high-density CHO cell cultures for the fed-batch process intensification.

Engineering death resistance in CHO cells for improved perfusion culture

The reliable and cost-efficient manufacturing of monoclonal antibodies (mAbs) is essential to fulfil their ever-growing demand. Cell death in bioreactors reduces productivity and product quality, and is largely attributed to apoptosis. In perfusion bioreactors, this leads to the necessity of a bleed stream, which negatively affects the overall process economy. To combat this limitation, death-resistant Chinese hamster ovary cell lines were developed by simultaneously knocking out the apoptosis effector proteins Bak1, Bax, and Bok with CRISPR technology. These cell lines were cultured in fed-batch and perfusion bioreactors and compared to an unmodified control cell line. In fed-batch, the death-resistant cell lines showed higher cell densities and longer culture durations, lasting nearly a month under standard culture conditions. In perfusion, the death-resistant cell lines showed slower drops in viability and displayed an arrest in cell division after which cell size increased instead. Pertinently, the death-resistant cell lines demonstrated the ability to be cultured for several weeks without bleed, and achieved similar volumetric productivities at lower cell densities than that of the control cell line. Perfusion culture reduced fragmentation of the mAb produced, and the death-resistant cell lines showed increased glycosylation in the light chain in both bioreactor modes. These data demonstrate that rationally engineered death-resistant cell lines are ideal for mAb production in perfusion culture, negating the need to bleed the bioreactor whilst maintaining product quantity and quality.

Upstream cell culture process characterization and in-process control strategy development at pandemic speed

As of early 2022, the coronavirus disease 2019 (COVID-19) pandemic remains a substantial global health concern. Different treatments for COVID-19, such as anti-COVID-19 neutralizing monoclonal antibodies (mAbs), have been developed under tight timelines. Not only mAb product and clinical development but also chemistry, manufacturing, and controls (CMC) process development at pandemic speed are required to address this highly unmet patient need. CMC development consists of early- and late-stage process development to ensure sufficient mAb manufacturing yield and consistent product quality for patient safety and efficacy. Here, we report a case study of late-stage cell culture process development at pandemic speed for mAb1 and mAb2 production as a combination therapy for a highly unmet patient treatment. We completed late-stage cell culture process characterization (PC) within approximately 4 months from the cell culture process definition to the initiation of the manufacturing process performance qualification (PPQ) campaign for mAb1 and mAb2, in comparison to a standard one-year PC timeline. Different strategies were presented in detail at different PC steps, i.e., pre-PC risk assessment, scale-down model development and qualification, formal PC experiments, and in-process control strategy development for a successful PPQ campaign that did not sacrifice quality. The strategies we present may be applied to accelerate late-stage process development for other biologics to reduce timelines.

Bax and Bak knockout apoptosis-resistant CHO cell lines significantly improve culture viability and titer in intensified fed-batch culture process

In the field of therapeutic protein production, process intensification strategies entailing higher starting cell seeding densities, can potentially increase culture productivity, lower cost of goods and improve facility utilization. However, increased cell densities often trigger apoptotic cell death at the end of the cell culture process and thus reduce total viable cell count. Apoptosis-resistant Chinese hamster ovary (CHO) cell lines may offer the possibility to diminish this undesired outcome of the intensified production process. In this study, we have generated and tested Bax/Bak double-knock-out (DKO) apoptosis resistant hosts to produce standard and bispecific antibodies, as well as complex molecules in intensified production processes both as pools and single cell clones, and at different scales. In all cases, therapeutic proteins expressed from clones or pools generated from the Bax/Bak DKO hosts showed not only better viability but also enabled extended productivity in the later stages of the 14-day intensified production process. The product qualities of the produced molecules were comparable between Bax/Bak DKO and wild type (WT) cells. Overall, we showed that Bax/Bak DKO apoptosis-resistant host cell lines significantly improve viability and volumetric productivity of the intensified production cultures without altering product qualities. This article is protected by copyright. All rights reserved.

Perfusion culture of Chinese Hamster Ovary cells for bioprocessing applications

Much of the biopharmaceutical industry's success over the past 30 years has relied on products derived from Chinese Hamster Ovary (CHO) cell lines. During this time, improvements in mammalian cell cultures have come from cell line development and process optimization suited for large-scale fed-batch processes. Originally developed for high cell densities and sensitive products, perfusion processes have a long history. Driven by high volumetric titers and a small footprint, perfusion-based bioprocess research has regained an interest from academia and industry. The recent pandemic has further highlighted the need for such intensified biomanufacturing options. In this review, we outline the technical history of research in this field as it applies to biologics production in CHO cells. We demonstrate a number of emerging trends in the literature and corroborate these with underlying drivers in the commercial space. From these trends, we speculate that the future of perfusion bioprocesses is bright and that the fields of media optimization, continuous processing, and cell line engineering hold the greatest potential. Aligning in its continuous setup with the demands for Industry 4.0, perfusion biomanufacturing is likely to be a hot topic in the years to come.

Rapid intensification of an established CHO cell fed-batch process

Currently, the mammalian biomanufacturing industry explores process intensification (PI) to meet upcoming demands of biotherapeutics while keeping production flexible but, more importantly, as economic as possible. However, intensified processes often require more development time compared with conventional fed‐batches (FBs) preventing their implementation. Hence, rapid and efficient, yet straightforward strategies for PI are needed. In this study we demonstrate such a strategy for the intensification of an N‐stage FB by implementing N‐1 perfusion cell culture and high inoculum cell densities resulting in a robust intensified FB (iFB). Furthermore, we show successful combination of such an iFB with the addition of productivity enhancers, which has not been reported so far. The conventional CHO cell FB process was step‐wise improved and intensified rapidly in multi‐parallel small‐scale bioreactors using N‐1 perfusion. The iFBs were performed in 15 and 250 ml bioreactors and allowed to evaluate the impact on key process indicators (KPI): the space–time yield (STY) was successfully doubled from 0.28 to 0.55 g/L d, while product quality was maintained. This gain was generated by initially increasing the inoculation density, thus shrinking process time, and second supplementation with butyric acid (BA), which reduced cell growth and enhanced cell‐specific productivity from ~25 to 37 pg/(cell d). Potential impacts of PI on cell metabolism were evaluated using flux balance analysis. Initial metabolic differences between the standard and intensified process were observed but disappeared quickly. This shows that PI can be achieved rapidly for new as well as existing processes without introducing sustained changes in cellular and metabolic behavior.

Automation of high CHO cell density seed intensification via online control of the cell specific perfusion rate and its impact on the N-stage inoculum quality

Current CHO cell production processes require an optimized space-time-yield. Process intensification can support achieving this by enhancing the productivity and improving facility utilization. The use of perfusion at the last stage of the seed train (N-1) for high cell density inoculation of the fed-batch N-stage production culture is a relatively new approach with few industry applicable examples. Within this work, the impact of the cell-specific perfusion rate (CSPR) of the N-1 perfusion and the relevance of its control for the quality of generated inoculation cells was evaluated using an automated perfusion rate (PR) control based on online biomass measurements. Precise correlations (R² = 0.99) between permittivity and viable cell counts were found up to the high densities of 100⋅10⁶ c·mL^-1. Cells from N-1 perfusion were cultivated at a high and low CSPR with 50 and 20 pL·(c·d)^-1, respectively. Lowered cell growth and an increased apoptotic reaction was found as a consequence of the latter due to nutrient limitations and reduced uptake rates. Subsequently, batch cultivations (N-stage) from the different N-1 sources were inoculated to evaluate the physiological state of the inoculum. Successive responses resulting from the respective N-1 condition were uncovered. While cell growth and productivity of approaches inoculated from high CSPR and a conventional seed were comparable, low CSPR inoculation suffered significantly in terms of reduced initial cell growth and impaired viability. This study underlines the importance to determine the CSPR for the design and implementation of an N-1 perfusion process in order to achieve the desired performance at the crucial production stage.

Antibody capture process based on magnetic beads from very high cell density suspension

Cell clarification represents a major challenge for the intensification through very high cell density in the production of biopharmaceuticals such as monoclonal antibodies (mAbs). The present report proposes a solution to this challenge in a streamlined process where cell clarification and mAb capture are performed in a single step using magnetic beads coupled with protein A. Capture of mAb from non-clarified CHO cell suspension showed promising results; however, it has not been demonstrated that it can handle the challenge of very high cell density as observed in intensified fed-batch cultures. The performances of magnetic bead-based mAb capture on non-clarified cell suspension from intensified fed-batch culture were studied. Capture from a culture at density larger than 100 × 10⁶ cells/ml provided an adsorption efficiency of 99% and an overall yield of 93% with a logarithmic host cell protein (HCP) clearance of ≈2-3 and a resulting HCP concentration ≤≈5 ppm. These results show that direct capture from very high cell density cell suspension is possible without prior processing. This technology, which brings significant benefits in terms of operational cost reduction and performance improvements such as low HCP, can be a powerful tool alleviating the challenge of process intensification.

Productivity improvement and charge variant modulation for intensified cell culture processes by adding a carboxypeptidase B (CpB) treatment step

The goal of cell culture process intensification is to improve productivity while maintaining acceptable quality attributes. In this report, four processes, namely a conventional manufacturing Process A, and processes intensified by enriched N-1 seed (Process B), by perfusion N-1 seed (Process C), and by perfusion production (Process D) were developed for the production of a monoclonal antibody. The three intensified processes substantially improved productivity, however, the product either failed to meet the specification for charge variant species (main peak) for Process D or the production process required early harvest to meet the specification for charge variant species, Day 10 or Day 6 for Processes B and C, respectively. The lower main peak for the intensified processes was due to higher basic species resulting from higher C-terminal lysine. To resolve this product quality issue, we developed an enzyme treatment method by introducing carboxypeptidase B (CpB) to clip the C-terminal lysine, leading to significantly increased main peak and an acceptable and more homogenous product quality for all the intensified processes. Additionally, Processes B and C with CpB treatment extended bioreactor durations to Day 14 increasing titer by 38% and 108%, respectively. This simple yet effective enzyme treatment strategy could be applicable to other processes that have similar product quality issues.

End-to-end collaboration to transform biopharmaceutical development and manufacturing

An ambitious 10‐year collaborative program is described to invent, design, demonstrate, and support commercialization of integrated biopharmaceutical manufacturing technology intended to transform the industry. Our goal is to enable improved control, robustness, and security of supply, dramatically reduced capital and operating cost, flexibility to supply an extremely diverse and changing portfolio of products in the face of uncertainty and changing demand, and faster product development and supply chain velocity, with sustainable raw materials, components, and energy use. The program is organized into workstreams focused on end‐to‐end control strategy, equipment flexibility, next generation technology, sustainability, and a physical test bed to evaluate and demonstrate the technologies that are developed. The elements of the program are synergistic. For example, process intensification results in cost reduction as well as increased sustainability. Improved robustness leads to less inventory, which improves costs and supply chain velocity. Flexibility allows more products to be consolidated into fewer factories, reduces the need for new facilities, simplifies the acquisition of additional capacity if needed, and reduces changeover time, which improves cost and velocity. The program incorporates both drug substance and drug product manufacturing, but this paper will focus on the drug substance elements of the program.

Rational Design of Single Copy Expression Cassettes in Defined Chromosomal Sites Overcomes Intraclonal Cell-to-Cell Expression Heterogeneity and Ensures Robust Antibody Production

The expression of endogenous genes as well as transgenes depends on regulatory elements within and surrounding genes as well as their epigenetic modifications. Members of a cloned cell population often show pronounced cell-to-cell heterogeneity with respect to the expression of a certain gene. To investigate the heterogeneity of recombinant protein expression we targeted cassettes into two preselected chromosomal hot-spots in Chinese hamster ovary (CHO) cells. Depending on the gene of interest and the design of the expression cassette, we found strong expression variability that could be reduced by epigenetic modifiers, but not by site-specific recruitment of the modulator dCas9-VPR. In particular, the implementation of ubiquitous chromatin opening elements (UCOEs) reduced cell-to-cell heterogeneity and concomitantly increased expression. The application of this method to recombinant antibody expression confirmed that rational design of cell lines for production of transgenes with predictable and high titers is a promising approach.

Developments and opportunities in continuous biopharmaceutical manufacturing

Today's biologics manufacturing practices incur high costs to the drug makers, which can contribute to high prices for patients. Timely investment in the development and implementation of continuous biomanufacturing can increase the production of consistent-quality drugs at a lower cost and a faster pace, to meet growing demand. Efficient use of equipment, manufacturing footprint, and labor also offer the potential to improve drug accessibility. Although technological efforts enabling continuous biomanufacturing have commenced, challenges remain in the integration, monitoring, and control of traditionally segmented unit operations. Here, we discuss recent developments supporting the implementation of continuous biomanufacturing, along with their benefits.

Applications and analysis of hydrolysates in animal cell culture

Animal cells are used in the manufacturing of complex biotherapeutic products since the 1980s. From its initial uses in biological research to its current importance in the biopharmaceutical industry, many types of culture media were developed: from serum-based media to serum-free to protein-free chemically defined media. The cultivation of animal cells economically has become the ultimate goal in the field of biomanufacturing. Serum serves as a source of amino acids, lipids, proteins and most importantly growth factors and hormones, which are essential for many cell types. However, the use of serum is unfavorable due to its high price tag, increased lot-to-lot variations and potential risk of microbial contamination. Efforts are progressively being made to replace serum with recombinant proteins such as growth factors, cytokines and hormones, as well as supplementation with lipids, vitamins, trace elements and hydrolysates. While hydrolysates are more complex, they provide a diverse source of nutrients to animal cells, with potential beneficial effects beyond the nutritional value. In this review, we discuss the use of hydrolysates in animal cell culture and briefly cover the composition of hydrolysates, mode of action and potential contaminants with some perspectives on its potential role in animal cell culture media formulations in the future.

Why Is Batch Processing Still Dominating the Biologics Landscape? Towards an Integrated Continuous Bioprocessing Alternative

Continuous manufacturing of biologics (biopharmaceuticals) has been an area of active research and development for many reasons, ranging from the demand for operational streamlining to the requirement of achieving obvious economic benefits. At the same time, biopharma strives to develop systems and concepts that can operate at similar scales for clinical and commercial production—using flexible infrastructures, such as single-use flow paths and small surge vessels. These developments should simplify technology transfer, reduce footprint and capital investment, and will allow to react readily to changing market pressures while maintaining quality attributes. Despite a number of clearly identified benefits compared to traditional batch processes, continuous bioprocessing is still not widely adopted for commercial manufacturing. This paper details how industry-specific technological, organizational, economic, and regulatory barriers that exist in biopharmaceutical manufacturing are hindering the adoption of continuous production processes. Based on this understanding, the roles of process systems engineering (PSE), process analytical technologies, and process modeling and simulation are highlighted as key enabling tools in overcoming these multi-faceted barriers in today’s manufacturing environment. Of course, we do recognize that there is also a need for a clear set of regulations to guide a transition of biologics manufacturing towards continuous processing. Furthermore, the role played by the emerging fields of process integration and automation as well as digitalization is explored, as these are the tools of the future to facilitate this transition from batch to continuous production. Finally, an outlook focusing on technology, management, and regulatory aspects is presented to identify key concerted efforts required to drive the broad adaptation of continuous manufacturing in biopharmaceutical processes.