Ultrasound elastic tensor imaging: comparison with MR diffusion tensor imaging in the myocardium

Transfontanellar shear wave elastography of the neonatal brain for quantitative evaluation of white matter damage

Cerebral white matter damage (WMD) is the most frequent brain lesion observed in infants surviving premature birth. Qualitative B-mode cranial ultrasound (cUS) is widely used to assess brain integrity at bedside. Its limitations include lower discriminatory power to predict long-term outcomes compared to magnetic resonance imaging (MRI). Shear wave elastography (SWE), a promising ultrasound imaging modality, might improve this limitation by detecting quantitative differences in tissue stiffness. The study enrolled 90 neonates (52% female, mean gestational age = 30.1  ± 4.5 weeks), including 78 preterm and 12 term controls. Preterm neonates underwent B-mode and SWE assessments in frontal white matter (WM), parietal WM, and thalami on day of life (DOL) 3, DOL8, DOL21, 40 weeks, and MRI at term equivalent age (TEA). Term infants were assessed on DOL3 only. Our data revealed that brain stiffness increased with gestational age in preterm infants but remained lower at TEA compared to the control group. In the frontal WM, elasticity values were lower in preterm infants with WMD detected on B-mode or MRI at TEA and show a good predictive value at DOL3. Thus, brain stiffness measurement using SWE could be a useful screening method for early identification of preterm infants at high WMD risk.Registration numbers: EudraCT number ID-RCB: 2012-A01530-43, ClinicalTrial.gov number NCT02042716.

Ultrasound Shear Wave Elastography in Cardiology

The advent of high-frame rate imaging in ultrasound allowed the development of shear wave elastography as a noninvasive alternative for myocardial stiffness assessment. It measures mechanical waves propagating along the cardiac wall with speeds that are related to stiffness. The use of cardiac shear wave elastography in clinical studies is increasing, but a proper understanding of the different factors that affect wave propagation is required to correctly interpret results because of the heart's thin-walled geometry and intricate material properties. The aims of this review are to give an overview of the general concepts in cardiac shear wave elastography and to discuss in depth the effects of age, hemodynamic loading, cardiac morphology, fiber architecture, contractility, viscoelasticity, and system-dependent factors on the measurements, with a focus on clinical application. It also describes how these factors should be considered during acquisition, analysis, and reporting to ensure an accurate, robust, and reproducible measurement of the shear wave.

In plane quantification ofin vivomuscle elastic anisotropy factor by steered ultrasound pushing beams

Objective.Skeletal muscles are organized into distinct layers and exhibit anisotropic characteristics across various scales. Assessing the arrangement of skeletal muscles may provide valuable biomarkers for diagnosing muscle-related pathologies and evaluating the efficacy of clinical interventions.Approach. In this study, we propose a novel ultrafast ultrasound sequence constituted of steered pushing beams was proposed for ultrasound elastography applications in transverse isotropic muscle. Based on the propagation of the shear wave vertical mode, it is possible to fit the experimental results to retrieve in the same imaging plane, the shear modulus parallel to fibers as well as the elastic anisotropy factor (ratio of Young's moduli times the shear modulus perpendicular to fibers).Main results. The technique was demonstratedin vitroin phantoms andex vivoin fusiform beef muscles. At last, the technique was appliedin vivoon fusiform muscles (biceps brachii) and mono-pennate muscles (gastrocnemius medialis) during stretching and contraction.Significance. This novel sequence provides access to new structural and mechanical biomarkers of muscle tissue, including the elastic anisotropy factor, within the same imaging plane. Additionally, it enables the investigation of multiples parameters during muscle active and passive length changes.

[Echocardiography with high frame rates in the clinical practice : Principles, applications and perspectives]

Continuous developments in cardiovascular imaging, software and hardware have led to technological advancements that open new ways for assessing myocardial mechanics, hemodynamics, and function. Through new scan modalities, echocardiographic scanners can nowadays achieve very high frame rates up to 5000 frames s-1 which enables a wide variety of new applications, including shear wave elastography, ultrafast speckle tracking, the visualization of intracardiac blood flow and myocardial perfusion imaging. This review provides an overview of these advances and demonstrates possible applications and their potential added value in the clinical practice.

Impact of Ventricular Geometric Characteristics on Myocardial Stiffness Assessment Using Shear-Wave Velocity in Healthy Children and Young Adults

BACKGROUND

Diastolic myocardial stiffness (MS) can serve as a key diagnostic parameter for congenital or acquired heart diseases. Using shear modulus and shear-wave velocity (SWV), shear-wave elastography (SWE) is an emerging ultrasound-based technique that can allow noninvasive assessment of MS. However, MS extrinsic parameters such as left ventricular geometric characteristics could affect shear-wave propagation. The aims of this study were to determine a range of normal values of MS using SWE in age groups of healthy children and young adults and to explore the impact of left ventricular geometric characteristics on SWE.

METHODS

Sixty healthy volunteers were recruited in the study and divided into 2 groups: neonates (0-1 months old, n = 15) and >1 month old (1 month to 45 years of age, n = 45). SWE was performed using the Verasonics Vantage systems with a phased-array ultrasound probe. The anteroseptal basal segment was assessed in two views. SWE was electrocardiographically triggered during the end-diastolic phase. Conventional echocardiography was performed to assess ventricular function and anatomy. Results are presented as stiffness values along with mean velocity measurements and SDs. Simple and multivariate linear regression analyses were performed.

RESULTS

For neonates, mean MS was 1.87 ± 0.79 kPa (range, 0.59-2.91 kPa; mean SWV, 1.37 ± 0.57 m/sec), with high variability and no correlation with age (P = .239). For this age group, no statistically significant correlation was found between MS and any demographic or echocardiographic parameters (P > .05). For the >1 month old group, a mean MS value of 1.67 ± 0.53 kPa was observed (range, 0.6-3 kPa; mean SWV, 1.29 ± 0.49 m/sec) for healthy volunteers. When paired for age, no sex-related difference was observed (P = .55). In univariate linear regression analysis, age (r = 0.83, P < .01), diastolic interventricular septal thickness (r = 0.72, P < .01), and left ventricular end-diastolic diameter (r = 0.67, P < .01) were the parameters with the highest correlation coefficients with MS. In a multiple linear regression analysis incorporating these three parameters as cofounding factors, age was the only statistically significant parameters (r = 0.81, P = .02).

CONCLUSION

Diastolic MS increases linearly in children and young adults. Diastolic MS correlates more robustly with age than with myocardial and left ventricular geometric characteristics. However, the geometry affects SWV, implying the need to determine well-established boundaries in future studies for the clinical application of SWE.

Anisotropy in ultrasound shear wave elastography: An add-on to muscles characterization

Ultrasound shear wave elastography was developed the past decade, bringing new stiffness biomarker in clinical practice. This biomarker reveals to be of primarily importance for the diagnosis of breast cancer or liver fibrosis. In muscle this biomarker become much more complex due to the nature of the muscle itself: an anisotropic medium. In this manuscript we depict the underlying theory of propagating waves in such anisotropic medium. Then we present the available methods that can consider and quantify this parameter. Advantages and drawbacks are discussed to open the way to imagine new methods that can free this biomarker in a daily clinical practice.

Proof of Concept of 3-D Backscatter Tensor Imaging Tomography for Non-invasive Assessment of Human Breast Cancer Collagen Organization

Tumor growth, similarly to several other pathologies, tends to change the structural orientation of soft tissue fibers, which can become relevant markers for diagnosis. Current diagnosis protocols may require a biopsy for histological analysis, which is an invasive, painful and stressful procedure with a minimum turnaround time of 2 d. Otherwise, diagnosis may involve the use of complex methods with limited availability such as diffusion tensor imaging (magnetic resonance diffusion tensor imaging), which is not widely used in medical practice. Conversely, advanced methodologies in ultrasound imaging such as backscatter tensor imaging (BTI) might become a routine procedure in clinical practice at a limited cost. This method evaluates the local organization of soft tissues based on the spatial coherence of their backscattered ultrasonic echoes. Previous work has proven that BTI applied with matrix probes enables measurement of the orientation of soft tissue fibers, especially in the myocardium. The aims of the study described here were (i) to present for the first time a methodology for performing BTI in a volume on ex vivo human breast tumors using a linear probe and (ii) to display a first proof of concept of the link between BTI measurements and the orientation of collagen fibers.

Hadamard-Encoded Synthetic Transmit Aperture Imaging for Improved Lateral Motion Estimation in Ultrasound Elastography

Lateral motion estimation has been a challenge in ultrasound elastography mainly due to the low resolution, low sampling frequency, and lack of phase information in the lateral direction. Synthetic transmit aperture (STA) can achieve high resolution due to two-way focusing and can beamform high-density image lines for improved lateral motion estimation with the disadvantages of low signal-to-noise ratio (SNR) and limited penetration depth. In this study, Hadamard-encoded STA (Hadamard-STA) is proposed for the improvement of lateral motion estimation in elastography, and it is compared with STA and conventional focused wave (CFW) imaging. Simulations, phantom, and in vivo experiments were conducted to make the comparison. The normalized root mean square error (NRMSE) and the contrast-to-noise ratio (CNR) were calculated as the evaluation criteria in the simulations. The results show that, at a noise level of -10 dB and an applied strain of -1% (compression), Hadamard-STA decreases the NRMSEs of lateral displacements by 46.92% and 35.35%, decreases the NRMSEs of lateral strains by 52.34% and 39.75%, and increases the CNRs by 9.70 and 9.75 dB compared with STA and CFW, respectively. In the phantom experiments performed on a heterogeneous tissue-mimicking phantom, the sum of squared differences (SSD) between the reference and the motion-compensated RF data, and the CNR were calculated as the evaluation criteria. At an applied strain of -1.80%, Hadamard-STA is found to decrease the SSDs by 20.91% and 30.99% and increase the CNRs by 14.15 and 24.66 dB compared with STA and CFW, respectively. In the experiments performed on a breast phantom, Hadamard-STA achieves better visualization of the breast inclusion with a clearer boundary between the inclusion and the background than STA and CFW. The in vivo experiments were performed on a patient with a breast tumor, and the tumor could also be better visualized with a more homogeneous background in the strain image obtained by Hadamard-STA than by STA and CFW. These results demonstrate that Hadamard-STA achieves a substantial improvement in lateral motion estimation and maybe a competitive method for quasi-static elastography.

Ex Vivo Evaluation of Mechanical Anisotropic Tissues with High-Frequency Ultrasound Shear Wave Elastography

The use of imaging devices to assess directional mechanics of tissues is highly desirable. This is because the directional mechanics depend on fiber orientation, and altered directional mechanics are closely related to the pathological status of tissues. However, measuring directional mechanics in tissues with high-stiffness is challenging due to the difficulty of generating localized displacement in these tissues using acoustic radiation force, a general method for generating displacement in ultrasound-based elastography. In addition, common ultrasound probes do not provide rotational function, which makes the measurement of directional mechanics inaccurate and unreliable. Therefore, we developed a high-frequency ultrasound mechanical wave elastography system that can accommodate a wide range of tissue stiffness and is also equipped with a motorized rotation stage for precise imaging of directional mechanics. A mechanical shaker was applied to the elastography system to measure tissues with high-stiffness. Phantom and ex vivo experiments were performed. In the phantom experiments, the lateral and axial resolution of the system were determined to be 144 μm and 168 μm, respectively. In the ex vivo experiments, we used swine heart and cartilage, both of which are considered stiff. The elastography system allows us to acquire the directional mechanics with high angular resolution in the heart and cartilage. The results demonstrate that the developed elastography system is capable of imaging a wide range of tissues and has high angular resolution. Therefore, this system might be useful for the diagnostics of mechanically anisotropic tissues via ex vivo tests.

Assessing cardiac stiffness using ultrasound shear wave elastography

Shear wave elastography offers a new dimension to echocardiography: it measures myocardial stiffness. Therefore, it could provide additional insights into the pathophysiology of cardiac diseases affecting myocardial stiffness and potentially improve diagnosis or guide patient treatment. The technique detects fast mechanical waves on the heart wall with high frame rate echography, and converts their propagation velocity into a stiffness value. A proper interpretation of shear wave data is required as the shear wave interacts with the intrinsic, yet dynamically changing geometrical and material characteristics of the heart under pressure. This dramatically alters the wave physics of the propagating wave, demanding adapted processing methods compared to other shear wave elastography applications as breast tumor and liver stiffness staging. Furthermore, several advanced analysis methods have been proposed to extract supplementary material features such as viscosity and anisotropy, potentially offering additional diagnostic value. This review explains the general mechanical concepts underlying cardiac shear wave elastography and provides an overview of the preclinical and clinical studies within the field. We also identify the mechanical and technical challenges ahead to make shear wave elastography a valuable tool for clinical practice.

Smart ultrasound device for non-invasive real-time myocardial stiffness quantification of the human heart

Quantitative assessment of myocardial stiffness is crucial to understand and evaluate cardiac biomechanics and function. Despite the recent progresses of ultrasonic shear wave elastography, quantitative evaluation of myocardial stiffness still remains a challenge because of strong elastic anisotropy. In this paper we introduce a smart ultrasound approach for non-invasive real-time quantification of shear wave velocity (SWV) and elastic fractional anisotropy (FA) in locally transverse isotropic elastic medium such as the myocardium. The approach relies on a simultaneous multidirectional evaluation of the SWV without a prior knowledge of the fiber orientation. We demonstrated that it can quantify accurately SWV in the range of 1.5 to 6 m/s in transverse isotropic medium (FA<0.7) using numerical simulations. Experimental validation was performed on calibrated phantoms and anisotropic ex vivo tissues. A mean absolute error of 0.22 m/s was found when compared to gold standard measurements. Finally, in vivo feasibility of myocardial anisotropic stiffness assessment was evaluated in four healthy volunteers on the antero-septo basal segment and on anterior free wall of the right ventricle (RV) in end-diastole. A mean longitudinal SWV of 1.08 0.20 m/s was measured on the RV wall and 1.74 0.51 m/s on the Septal wall with a good intra-volunteer reproducibility (0.18 m/s). This approach has the potential to become a clinical tool for the quantitative evaluation of myocardial stiffness and diastolic function.

Spontaneous extension wave for in vivo assessment of arterial wall anisotropy

Another type of natural wave, traced from longitudinal wall motion and propagation along the artery, is observed in our in vivo human carotid artery experiments. We coin it as extension wave (EW) and hypothesize that EW velocity (EWV) is associated with arterial longitudinal stiffness. The EW is thus assumed to complement the pulse wave (PW), whose velocity (PWV) is tracked from the radial wall displacement and linked to arterial circumferential stiffness through the Moens-Korteweg equation, as indicators for arterial mechanical anisotropy quantification by noninvasive high-frame-rate ultrasound. The relationship between directional arterial stiffnesses and the two natural wave speeds was investigated in wave theory, finite-element simulations based on isotropic and anisotropic arterial models, and in vivo human common carotid artery (n = 10) experiments. Excellent agreement between the theory and simulations showed that EWV was 2.57 and 1.03 times higher than PWV in an isotropic and an anisotropic carotid artery model, respectively, whereas in vivo EWV was consistently lower than PWV in all 10 healthy human subjects. A strong linear correlation was substantiated in vivo between EWV and arterial longitudinal stiffness quantified by a well-validated vascular-guided wave imaging technique (VGWI). We thereby proposed a novel index calculated as EWV²/PWV² as an alternative to assess arterial mechanical anisotropy. Simulations and in vivo results corroborated the effect of mechanical anisotropy on the propagation of spontaneous waves along the arterial wall. The proposed anisotropy index demonstrated the feasibility of the concurrent EW and PW imaged by high frame-rate ultrasound in grading of arterial wall anisotropy.NEW & NOTEWORTHY An extension wave formed by longitudinal wall displacements was observed by high-frame-rate ultrasound in the human common carotid artery in vivo. A strong correlation between extension wave velocity and arterial longitudinal stiffness complements the well-established pulse wave, which is linked to circumferential stiffness, to noninvasively assess direction-dependent wall elasticity of the major artery. The proposed anisotropy index, which directly reflects arterial wall microstructure and function, might be a potential risk factor for screening (sub-) clinical cardiovascular diseases.

Influence of transducer orientation on shear wave velocity measurements of the iliotibial band

Tissue anisotropy influences estimation of mechanical properties of connective tissues, such as the iliotibial band (ITB). This study investigated the influence of ultrasound transducer rotation and tilt on shear wave velocity (SWV, an index of stiffness) measurements of the ITB and the intra-rater repeatability of SWV measurements in the longitudinal direction. SWV was measured unilaterally (dominant limb) using ultrasound shear wave elastography in the middle region of the ITB in supine at rest (20-25° knee flexion) in ten healthy volunteers (4 females). A 3-dimensional video system provided real-time feedback of probe orientation with respect to the thigh. Measurements were made at 10° increments of probe rotation, from longitudinal to transverse alignment relative to the approximate direction of ITB fibres, and 5-10° tilts about the longitudinal and sideways axes of the transducer. One-way repeated measures ANOVA compared SWV between angles and tilts. Intraclass correlation coefficients (ICCs) and standard error of measurement (SEM) were used to calculate repeatability for two to five (longitudinal only) repetitions. SWV was greatest when the transducer was aligned to ITB fibres (longitudinal: 10.5 ± 1.7 m/s) and lowest when perpendicular (transverse: 5.8 ± 2.4 m/s). Compared to longitudinal alignment, SWV decreased significantly (p < 0.01) when the transducer was rotated 20° or more. Tilted measurements did not differ between angles. Intra-rater repeatability was excellent with the average of two measurements (ICC = 0.99, 95% CI 0.95, 0.99; SEM = 0.31 m/s). These findings show that SWV changes with orientation relative to fibre direction. Transducer orientation requires careful control to ensure comparable measures.

Electronic Point Spread Function Rotation Using a Three-Row Transducer for ARFI-Based Elastic Anisotropy Assessment: In Silico and Experimental Demonstration

Degree of anisotropy (DoA) of mechanical properties has been assessed as the ratio of acoustic radiation force impulse (ARFI)-induced peak displacements (PDs) achieved using spatially asymmetric point spread functions (PSFs) that are rotated 90° to each other. Such PSF rotation has been achieved by manually rotating a linear array transducer, but manual rotation is cumbersome and prone to misalignment errors and higher variability in measurements. The purpose of this work is to evaluate the feasibility of electronic PSF rotation using a three-row transducer, which will reduce variability in DoA assessment. A Siemens 9L4, with 3×192 elements, was simulated in Field II to generate spatially asymmetric ARFI PSFs that were electronically rotated 63° from each other. Then, using the finite element method (FEM), PD due to the ARFI excitation PSFs in 42 elastic, incompressible, transversely isotropic (TI) materials with shear moduli ratios of 1.0-6.0 were modeled. Finally, the ratio of PDs achieved using the two rotated PSFs was evaluated to assess elastic DoA. DoA increased with increasing shear moduli ratios and distinguished materials with 17% or greater difference in shear moduli ratios (Wilcoxon, ). Experimentally, the ratio of PDs achieved using ARFI PSF rotated 63° from each other distinguished the biceps femoris muscle from two pigs, which had median shear moduli ratios of 4.25 and 3.15 as assessed by shear wave elasticity imaging (SWEI). These results suggest that ARFI-based DoA assessment can be achieved without manual transducer rotation using a three-row transducer capable of electronically rotating PSFs by 63°. It is expected that electronic PSF rotation will facilitate data acquisitions and improve the reproducibility of elastic anisotropy assessments.

Correlation length ratio as a parameter for determination of fiber-like structures in soft tissues

Quantitative ultrasound methods can provide valuable information about the microstructure of a material or tissue. This works well when the common assumptions of homogeneity, isotropy, and diffuse scattering conditions are valid. In biological tissues, however, these assumptions are often violated because the microstructure of biological tissues is often heterogeneous and anisotropic. The microstructure of biological tissues can change with disease, and therefore accurate identification and description of a tissue's microstructure can offer important clinical insight. To address the challenge of evaluating the microstructure of biological tissues, here we introduce a novel parameter called the correlation length ratio (CLR), a ratio of lateral to axial correlation lengths for backscattered echo signals. We developed it to determine the presence of fiber-like structures in soft tissues by comparing this value in tissue to a threshold determined from a reference material that is homogeneous, isotropic, and provides diffuse scattering. We tested this novel parameter in phantoms with spherical scattering sources, in an anisotropic phantom (containing elongated fibers), and in human biceps muscle. We found that the CLR accurately detected the presence of elongated structures in both the anisotropic phantom and muscle. These results encourage further exploration of this novel parameter in microstructurally complex tissues.

Assessing Myocardial Architecture: The Challenges and Controversies

In recent decades, investigators have strived to describe and quantify the orientation of the cardiac myocytes in an attempt to classify their arrangement in healthy and diseased hearts. There are, however, striking differences between the investigations from both a technical and methodological standpoint, thus limiting their comparability and impeding the drawing of appropriate physiological conclusions from the structural assessments. This review aims to elucidate these differences, and to propose guidance to establish methodological consensus in the field. The review outlines the theory behind myocyte orientation analysis, and importantly has identified pronounced differences in the definitions of otherwise widely accepted concepts of myocytic orientation. Based on the findings, recommendations are made for the future design of studies in the field of myocardial morphology. It is emphasised that projection of myocyte orientations, before quantification of their angulation, introduces considerable bias, and that angles should be assessed relative to the epicardial curvature. The transmural orientation of the cardiomyocytes should also not be neglected, as it is an important determinant of cardiac function. Finally, there is considerable disagreement in the literature as to how the orientation of myocardial aggregates should be assessed, but to do so in a mathematically meaningful way, the normal vector of the aggregate plane should be utilised.

A direct comparison of natural and acoustic-radiation-force-induced cardiac mechanical waves

Natural and active shear wave elastography (SWE) are potential ultrasound-based techniques to non-invasively assess myocardial stiffness, which could improve current diagnosis of heart failure. This study aims to bridge the knowledge gap between both techniques and discuss their respective impacts on cardiac stiffness evaluation. We recorded the mechanical waves occurring after aortic and mitral valve closure (AVC, MVC) and those induced by acoustic radiation force throughout the cardiac cycle in four pigs after sternotomy. Natural SWE showed a higher feasibility than active SWE, which is an advantage for clinical application. Median propagation speeds of 2.5-4.0 m/s and 1.6-4.0 m/s were obtained after AVC and MVC, whereas ARF-based median speeds of 0.9-1.2 m/s and 2.1-3.8 m/s were reported for diastole and systole, respectively. The different wave characteristics in both methods, such as the frequency content, complicate the direct comparison of waves. Nevertheless, a good match was found in propagation speeds between natural and active SWE at the moment of valve closure, and the natural waves showed higher propagation speeds than in diastole. Furthermore, the results demonstrated that the natural waves occur in between diastole and systole identified with active SWE, and thus represent a myocardial stiffness in between relaxation and contraction.

Role of Ultrasound in Low Back Pain: A Review

Low back pain is one of most common musculoskeletal disorders around the world. One major problem clinicians face is the lack of objective assessment modalities. Computed tomography and magnetic resonance imaging are commonly utilized but are unable to clearly distinguish patients with low back pain from healthy patients with respect to abnormalities. The reason may be the anisotropic nature of muscles, which is altered in function, and the scans provide only structural assessment. In view of this, ultrasound may be helpful in understanding the disease as it is performed in real-time and comprises different modes that measure thickness, blood flow and stiffness. By the use of ultrasound, patients with low back pain have been found to differ from healthy patients with respect to the thickness and stiffness of the transversus abdominis, thoracolumbar fascia and multifidus. The study results are currently still not conclusive, and further study is necessary to validate. Future work should focus on quantitative assessment of these tissues to provide textural, structural, hemodynamic and mechanical studies of low back pain. This review highlights the current understanding of how medical ultrasound has been used for diagnosis and study of low back pain and discusses potential new applications.

Anatomically correct assessment of the orientation of the cardiomyocytes using diffusion tensor imaging

Diffusion tensor imaging has been used for assessing the orientation of cardiac myocytes for decades. Striking methodological differences exist between studies when quantifying these orientations. This limits the comparability between studies, and impedes collaboration and the drawing of appropriate physiological conclusions. We have sought to elucidate these differences, permitting us to propose a standardised "tool set" that might better establish consensus in future studies. We fixed hearts from seven 25 kg pigs in formalin, and scanned them using diffusion tensor imaging. Using various angle definitions as found in literature, we assessed the orientations of cardiomyocytes, comparing them in terms of helical and intrusion angles, along with the orientation of their aggregations. The difference between assessment of the helical angle with and without relation to the epicardial curvature was 25.2° (SD: 7.9) at the base, 5.8° (1.9) at the equatorial level, and 28.0° (7.0) at the apex, ANOVA P = 0.001. In comparable fashion, the intrusion angle differed by 25.9° (12.9), 7.6° (0.98) and 17.5° (4.7), P = 0.01, and the angle of the aggregates (E3-angle) differed by 25.0° (13.5) at the base, 9.4° (1.7) at the equator, and 23.1° (6.2) apically, P = 0.003. When assessing 14 definitions used in literature to calculate the orientation of aggregates, only 4 rendered identical results. The findings show that any attempt to use projection of eigenvectors introduces considerable bias. The epicardial curvature of the ventricular cone needs to be taken into account when seeking to provide accurate quantification of the orientation of the aggregated cardiomyocytes, especially in the apical and basal regions. This means that projection of eigenvectors should be avoided prior to quantifying myocyte orientation, especially when assessing radial orientation. Based on our results, we suggest appropriate methods for valid assessment of myocyte orientation using diffusion tensor imaging.

Myocardial Stiffness Evaluation Using Noninvasive Shear Wave Imaging in Healthy and Hypertrophic Cardiomyopathic Adults

OBJECTIVES

The goal of our study was to investigate the potential of myocardial shear wave imaging (SWI) to quantify the diastolic myocardial stiffness (MS) (kPa) noninvasively in adult healthy volunteers (HVs) and its physiological variation with age, and in hypertrophic cardiomyopathy (HCM) populations with heart failure and preserved ejection function (HFpEF).

BACKGROUND

MS is an important prognostic and diagnostic parameter of the diastolic function. MS is affected by physiological changes but also by pathological alterations of extracellular and cellular tissues. However, the clinical assessment of MS and the diastolic function remains challenging. SWI is a novel ultrasound-based technique that has the potential to provide intrinsic MS noninvasively.

METHODS

We prospectively included 80 adults: 60 HV (divided into 3 groups: 20- to 39-year old patients [n = 20]; 40- to 59-year-old patients [n = 20]; and 60- to 79-year-old patients [n = 20]) and 20 HCM-HFpEF patients. Echocardiography, cardiac magnetic resonance imaging and biological explorations were achieved. MS evaluation was performed using an ultrafast ultrasound scanner with cardiac phased array. The fractional anisotropy of MS was also estimated.

RESULTS

MS increased significantly with age in the HV group (the mean MS was 2.59 ± 0.58 kPa, 4.70 ± 0.88 kPa, and 6.08 ± 1.06 kPa for the 20- to 40-year-old, 40- to 60-year-old, and 60- to 80-year-old patient groups, respectively; p < 0.01 between each group). MS was significantly higher in HCM-HFpEF patients than in HV patients (mean MS = 12.68 ± 2.91 kPa vs. 4.47 ± 1.68 kPa, respectively; p < 0.01), with a cut-off at 8 kPa (area under the curve = 0.993; sensitivity = 95%, specificity = 100%). The fractional anisotropy was lower in HCM-HFpEF (mean = 0.133 ± 0.073) than in HV (0.238 ± 0.068) (p < 0.01). Positive correlations were found between MS and diastolic parameters in echocardiography (early diastolic peak/early diastolic mitral annular velocity, r = 0.783; early diastolic peak/transmitral flow propagation velocity, r = 0.616; left atrial volume index, r = 0.623) and with fibrosis markers in cardiac magnetic resonance (late gadolinium enhancement, r = 0.804; myocardial T1 pre-contrast, r = 0.711).

CONCLUSIONS

MS was found to increase with age in healthy adults and was significantly higher in HCM-HFpEF patients. Myocardial SWI has the potential to become a clinical tool for the diagnostic of diastolic dysfunction. (Non-invasive Evaluation of Myocardial Stiffness by Elastography [Elasto-Cardio]; NCT02537041).

Imaging technologies for cardiac fiber and heart failure: a review

There has been an increasing interest in studying cardiac fibers in order to improve the current knowledge regarding the mechanical and physiological properties of the heart during heart failure (HF), particularly early HF. Having a thorough understanding of the changes in cardiac fiber orientation may provide new insight into the mechanisms behind the progression of left ventricular (LV) remodeling and HF. We conducted a systematic review on various technologies for imaging cardiac fibers and its link to HF. This review covers literature reports from 1900 to 2017. PubMed and Google Scholar databases were searched using the keywords "cardiac fiber" and "heart failure" or "myofiber" and "heart failure." This review highlights imaging methodologies, including magnetic resonance diffusion tensor imaging (MR-DTI), ultrasound, and other imaging technologies as well as their potential applications in basic and translational research on the development and progression of HF. MR-DTI and ultrasound have been most useful and significant in evaluating cardiac fibers and HF. New imaging technologies that have the ability to measure cardiac fiber orientations and identify structural and functional information of the heart will advance basic research and clinical diagnoses of HF.

An in silico framework to analyze the anisotropic shear wave mechanics in cardiac shear wave elastography

Shear wave elastography (SWE) is a potential tool to non-invasively assess cardiac muscle stiffness. This study focused on the effect of the orthotropic material properties and mechanical loading on the performance of cardiac SWE, as it is known that these factors contribute to complex 3D anisotropic shear wave propagation. To investigate the specific impact of these complexities, we constructed a finite element model with an orthotropic material law subjected to different uniaxial stretches to simulate SWE in the stressed cardiac wall. Group and phase speed were analyzed in function of tissue thickness and virtual probe rotation angle. Tissue stretching increased the group and phase speed of the simulated shear wave, especially in the direction of the muscle fiber. As the model provided access to the true fiber orientation and material properties, we assessed the accuracy of two fiber orientation extraction methods based on SWE. We found a higher accuracy (but lower robustness) when extracting fiber orientations based on the location of maximal shear wave speed instead of the angle of the major axis of the ellipsoidal group speed surface. Both methods had a comparable performance for the center region of the cardiac wall, and performed less well towards the edges. Lastly, we also assessed the (theoretical) impact of pathology on shear wave physics and characterization in the model. It was found that SWE was able to detect changes in fiber orientation and material characteristics, potentially associated with cardiac pathologies such as myocardial fibrosis. Furthermore, the model showed clearly altered shear wave patterns for the fibrotic myocardium compared to the healthy myocardium, which forms an initial but promising outcome of this modeling study.

Review of the emerging role of optical polarimetry in characterization of pathological myocardium

Myocardial infarction (MI), a cause of significant morbidity and mortality, is typically followed by microstructural alterations where the necrotic myocardium is steadily replaced with a collagen scar. Engineered remodeling of the fibrotic scar via stem cell regeneration has been shown to improve/restore the myocardium function after MI. Nevertheless, the heterogeneous nature of the scar patch may impair the myocardial electrical integrity, leading to the formation of arrhythmogenesis. Radiofrequency ablation (RFA) offers an effective treatment for focal arrhythmias where local heating generated via electric current at specific spots in the myocardium ablate the arrhythmogenic foci. Characterization of these myocardial pathologies (i.e., infarcted, stem cell regenerated, and RFA-ablated myocardial tissues) is of potential clinical importance. Optical polarimetry, the use of light to map and characterize the polarization signatures of a sample, has emerged as a powerful imaging tool for structural characterization of myocardial tissues, exploiting the underlying highly fibrous tissue nature. This study aims to review the recent progress in optical polarimetry pertaining to the characterization of myocardial pathologies while describing the underlying biological rationales that give rise to the optical imaging contrast in various pathologies of the myocardium. Future possibilities of and challenges to optical polarimetry in cardiac imaging clinics are also discussed.

Ultra-high field upper extremity peripheral nerve and non-contrast enhanced vascular imaging

OBJECTIVE

The purpose of this study was to explore the efficacy of Ultra-high field [UHF] 7 Tesla [T] MRI as compared to 3T MRI in non-contrast enhanced [nCE] imaging of structural anatomy in the elbow, forearm, and hand [upper extremity].

MATERIALS AND METHOD

A wide range of sequences including T1 weighted [T1] volumetric interpolate breath-hold exam [VIBE], T2 weighted [T2] double-echo steady state [DESS], susceptibility weighted imaging [SWI], time-of-flight [TOF], diffusion tensor imaging [DTI], and diffusion spectrum imaging [DSI] were optimized and incorporated with a radiofrequency [RF] coil system composed of a transverse electromagnetic [TEM] transmit coil combined with an 8-channel receive-only array for 7T upper extremity [UE] imaging. In addition, Siemens optimized protocol/sequences were used on a 3T scanner and the resulting images from T1 VIBE and T2 DESS were compared to that obtained at 7T qualitatively and quantitatively [SWI was only qualitatively compared]. DSI studio was utilized to identify nerves based on analysis of diffusion weighted derived fractional anisotropy images. Images of forearm vasculature were extracted using a paint grow manual segmentation method based on MIPAV [Medical Image Processing, Analysis, and Visualization].

RESULTS

High resolution and high quality signal-to-noise ratio [SNR] and contrast-to-noise ratio [CNR]-images of the hand, forearm, and elbow were acquired with nearly homogeneous 7T excitation. Measured [performed on the T1 VIBE and T2 DESS sequences] SNR and CNR values were almost doubled at 7T vs. 3T. Cartilage, synovial fluid and tendon structures could be seen with higher clarity in the 7T T1 and T2 weighted images. SWI allowed high resolution and better quality imaging of large and medium sized arteries and veins, capillary networks and arteriovenous anastomoses at 7T when compared to 3T. 7T diffusion weighted sequence [not performed at 3T] demonstrates that the forearm nerves are clearly delineated by fiber tractography. The proper digital palmar arteries and superficial palmar arch could also be clearly visualized using TOF nCE 7T MRI.

CONCLUSION

Ultra-high resolution neurovascular imaging in upper extremities is possible at 7T without use of renal toxic intravenous contrast. 7T MRI can provide superior peripheral nerve [based on fiber anisotropy and diffusion coefficient parameters derived from diffusion tensor/spectrum imaging] and vascular [nCE MRA and vessel segmentation] imaging.

Acoustic Radiation Force Impulse (ARFI)-Induced Peak Displacements Reflect Degree of Anisotropy in Transversely Isotropic Elastic Materials

In transversely isotropic (TI) materials, mechanical properties (Young's modulus, shear modulus, and Poisson's ratio) are different along versus across the axis of symmetry (AoS). In this work, the feasibility of interrogating such directional mechanical property differences using acoustic radiation force impulse (ARFI) imaging is investigated. We herein test the hypotheses that 1) ARFI-induced peak displacements (PDs) vary with TI material orientations when an asymmetrical ARFI excitation point spread function (PSF) is used, but not when a symmetrical ARFI PSF is employed; and 2) the ratio of PDs induced with the long axis of an asymmetrical ARFI PSF oriented along versus across the material's AoS is related to the degree of anisotropy of the material. These hypotheses were tested in silico using finite element method (FEM) models and Field II. ARFI excitations had F/1.5, 3, 4, or 5 focal configurations, with the F/1.5 and F/5 cases having the most asymmetrical and symmetrical PSFs at the focal depth, respectively. These excitations were implemented for ARFI imaging in 52 different simulated TI materials with varying degrees of anisotropy, and the ratio of ARFI-induced PDs was calculated. The change in the ratio of PDs with respect to the anisotropy of the materials was highest for the F/1.5, indicating that PD was most strongly impacted by the material orientation when the ARFI excitation was the most asymmetrical. On the contrary, the ratio of PDs did not depend on the anisotropy of the material for the F/5 ARFI excitation, suggesting that PD did not depend on material orientation when the ARFI excitation was symmetrical. Finally, the ratio of PDs achieved using asymmetrical ARFI PSF reflected the degree of anisotropy in TI materials. These results support that symmetrical ARFI focal configurations are desirable when the orientation of the ARFI excitation to the AoS is not specifically known and measurement standardization is important, such as for longitudinal or cross-sectional studies of anisotropic organs. However, asymmetrical focal configurations are useful for exploiting anisotropy, which may be diagnostically relevant. Feasibility for future experimental implementation is demonstrated by simulating ultrasonic displacement tracking and by varying the ARF duration.

Quantitative Assessment of Left Ventricular Diastolic Stiffness Using Cardiac Shear Wave Elastography: A Pilot Study

OBJECTIVES

The purpose of this study was to systematically investigate the feasible echocardiographic views for human transthoracic cardiac shear wave elastography (SWE) and the impact of myocardial anisotropy on myocardial stiffness measurements.

METHODS

A novel cardiac SWE technique using pulse inversion harmonic imaging and time-aligned sequential tracking was developed for this study. The technique can measure the quantitative local myocardial stiffness noninvasively. Ten healthy volunteers were recruited and scanned by the proposed technique 3 times on 3 different days.

RESULTS

Seven combinations of echocardiographic views and left ventricular (LV) segments were found to be feasible for LV diastolic stiffness measurements: basal interventricular septum under parasternal short- and long-axis views; mid interventricular septum under parasternal short- and long-axis views; anterior LV free wall under parasternal short- and long-axis views; and posterior LV free wall under a parasternal short-axis view. Statistical analyses showed good repeatability of LV diastolic stiffness measurements among 3 different days from 70% of the participants for the basal interventricular septum and posterior LV free wall short-axis views. On the same LV segment, the mean diastolic shear wave speed measurements from the short-axis view were statistically different from the long-axis measurements: 1.82 versus 1.29 m/s for the basal interventricular septum; 1.81 versus 1.45 m/s for mid interventricular septum; and 1.96 versus 1.77 m/s for the anterior LV free wall, indicating that myocardial anisotropy plays a substantial role in LV diastolic stiffness measurements.

CONCLUSIONS

These results establish the preliminary normal range of LV diastolic stiffness under different scan views and provide important guidance for future clinical studies using cardiac SWE.

Mapped Chebyshev pseudo-spectral method for simulating the shear wave propagation in the plane of symmetry of a transversely isotropic viscoelastic medium

Shear wave elastography is a versatile technique that is being applied to many organs. However, in tissues that exhibit anisotropic material properties, special care must be taken to estimate shear wave propagation accurately and efficiently. A two-dimensional simulation method is implemented to simulate the shear wave propagation in the plane of symmetry in transversely isotropic viscoelastic media. The method uses a mapped Chebyshev pseudo-spectral method to calculate the spatial derivatives and an Adams-Bashforth-Moulton integrator with variable step sizes for time marching. The boundaries of the two-dimensional domain are surrounded by perfectly matched layers to approximate an infinite domain and minimize reflection errors. In an earlier work, we proposed a solution for estimating the apparent shear wave elasticity and viscosity of the spatial group velocity as a function of rotation angle through a low-frequency approximation by a Taylor expansion. With the solver implemented in MATLAB, the simulated results in this paper match well with the theory. Compared to the finite element method simulations we used before, the pseudo-spectral solver consumes less memory and is faster and achieves better accuracy.

Shear Wave Imaging of Passive Diastolic Myocardial Stiffness: Stunned Versus Infarcted Myocardium

Objectives

The aim of this study was to investigate the potential of shear wave imaging (SWI), a novel ultrasound-based technique, to noninvasively quantify passive diastolic myocardial stiffness in an ovine model of ischemic cardiomyopathy.

Background

Evaluation of diastolic left ventricular function is critical for evaluation of heart failure and ischemic cardiomyopathy. Myocardial stiffness is known to be an important property for the evaluation of the diastolic myocardial function, but this parameter cannot be measured noninvasively by existing techniques.

Methods

SWI was performed in vivo in open-chest procedures in 10 sheep. Ligation of a diagonal of the left anterior descending coronary artery was performed for 15 min (stunned group, n = 5) and 2 h (infarcted group, n = 5). Each procedure was followed by a 40-min reperfusion period. Diastolic myocardial stiffness was measured at rest, during ischemia, and after reperfusion by using noninvasive shear wave imaging. Simultaneously, end-diastolic left ventricular pressure and segmental strain were measured with a pressure catheter and sonomicrometers during transient vena caval occlusions to obtain gold standard evaluation of myocardial stiffness using end-diastolic strain-stress relationship (EDSSR).

Results

In both groups, the end-systolic circumferential strain was drastically reduced during ischemia (from 14.2 ± 1.2% to 1.3 ± 1.6% in the infarcted group and from 13.5 ± 3.0% to 1.9 ± 1.8% in the stunned group; p <0.01). SWI diastolic stiffness increased after 2 h of ischemia from 1.7 ± 0.4 to 6.2 ± 2.2 kPa (p < 0.05) and even more after reperfusion (12.1 ± 4.2 kPa; p < 0.01). Diastolic myocardial stiffening was confirmed by the exponential constant coefficient of the EDSSR, which increased from 8.8 ± 2.3 to 25.7 ± 9.5 (p < 0.01). In contrast, SWI diastolic stiffness was unchanged in the stunned group (2.3 ± 0.4 kPa vs 1.8 ± 0.3 kPa, p = NS) which was confirmed also by the exponential constant of EDSSR (9.7 ± 3.1 vs 10.2 ± 2.3, p = NS).

Conclusions

Noninvasive SWI evaluation of diastolic myocardial stiffness can differentiate between stiff, noncompliant infarcted wall and softer wall containing stunned myocardium.

DTI template-based estimation of cardiac fiber orientations from 3D ultrasound

PURPOSE

Cardiac muscle fibers directly affect the mechanical, physiological, and pathological properties of the heart. Patient-specific quantification of cardiac fiber orientations is an important but difficult problem in cardiac imaging research. In this study, the authors proposed a cardiac fiber orientation estimation method based on three-dimensional (3D) ultrasound images and a cardiac fiber template that was obtained from magnetic resonance diffusion tensor imaging (DTI).

METHODS

A DTI template-based framework was developed to estimate cardiac fiber orientations from 3D ultrasound images using an animal model. It estimated the cardiac fiber orientations of the target heart by deforming the fiber orientations of the template heart, based on the deformation field of the registration between the ultrasound geometry of the target heart and the MRI geometry of the template heart. In the experiments, the animal hearts were imaged by high-frequency ultrasound, T1-weighted MRI, and high-resolution DTI.

RESULTS

The proposed method was evaluated by four different parameters: Dice similarity coefficient (DSC), target errors, acute angle error (AAE), and inclination angle error (IAE). Its ability of estimating cardiac fiber orientations was first validated by a public database. Then, the performance of the proposed method on 3D ultrasound data was evaluated by an acquired database. Their average values were 95.4% ± 2.0% for the DSC of geometric registrations, 21.0° ± 0.76° for AAE, and 19.4° ± 1.2° for IAE of fiber orientation estimations. Furthermore, the feasibility of this framework was also performed on 3D ultrasound images of a beating heart.

CONCLUSIONS

The proposed framework demonstrated the feasibility of using 3D ultrasound imaging to estimate cardiac fiber orientation of in vivo beating hearts and its further improvements could contribute to understanding the dynamic mechanism of the beating heart and has the potential to help diagnosis and therapy of heart disease.

Material stiffness parameters as potential predictors of presence of left ventricle myocardial infarction: 3D echo-based computational modeling study

Background

Ventricle material properties are difficult to obtain under in vivo conditions and are not readily available in the current literature. It is also desirable to have an initial determination if a patient had an infarction based on echo data before more expensive examinations are recommended. A noninvasive echo-based modeling approach and a predictive method were introduced to determine left ventricle material parameters and differentiate patients with recent myocardial infarction (MI) from those without.

Methods

Echo data were obtained from 10 patients, 5 with MI (Infarct Group) and 5 without (Non-Infarcted Group). Echo-based patient-specific computational left ventricle (LV) models were constructed to quantify LV material properties. All patients were treated equally in the modeling process without using MI information. Systolic and diastolic material parameter values in the Mooney-Rivlin models were adjusted to match echo volume data. The equivalent Young’s modulus (YM) values were obtained for each material stress–strain curve by linear fitting for easy comparison. Predictive logistic regression analysis was used to identify the best parameters for infract prediction.

Results

The LV end-systole material stiffness (ES-YM_f) was the best single predictor among the 12 individual parameters with an area under the receiver operating characteristic (ROC) curve of 0.9841. LV wall thickness (WT), material stiffness in fiber direction at end-systole (ES-YM_f) and material stiffness variation (∆YM_f) had positive correlations with LV ejection fraction with correlation coefficients r = 0.8125, 0.9495 and 0.9619, respectively. The best combination of parameters WT + ∆YM_f was the best over-all predictor with an area under the ROC curve of 0.9951.

Conclusion

Computational modeling and material stiffness parameters may be used as a potential tool to suggest if a patient had infarction based on echo data. Large-scale clinical studies are needed to validate these preliminary findings.

Utility of MRI Diffusion Tensor Imaging in Carpal Tunnel Syndrome: A Meta-Analysis

BACKGROUND After successful utilization of diffusion tensor imaging (DTI) in detecting brain pathologies, it is now being examined for use in the detection of peripheral neuropathies. The aim of this meta-analysis was to evaluate the diagnostic potentials of DTI in carpal tunnel syndrome (CTS). MATERIAL AND METHODS The literature search was performed in multiple electronic databases using a keyword search and final selection of the studies was based on predetermined inclusion and exclusion criteria. We performed a meta-analyses of mean differences in fractional anisotropy (FA) and apparent diffusion coefficient (ADC) between CTS patient and healthy subjects. Publication bias detection was done with Begg's test and sensitivity analyses were performed to explore the source/s of higher heterogeneity and the authenticity of results. RESULTS FA was significantly lower in CTS patients in comparison with healthy subjects (mean and the difference [95% confidence interval] was -0.06 [-0.10, -0.02] (p=0.003). The ADC was significantly higher in CTS patients (mean difference [95% CI] was 0.10 [0.02, 0.18], p=0.02). Overall sensitivity of FA-based diagnosis was 82.82%, with 77.83% specificity. CONCLUSIONS DTI can be a valuable tool in diagnosing CTS.

Toward 3-D Echocardiographic Determination of Regional Myofiber Structure

As a step toward the goal of relating changes in underlying myocardial structure to observed altered cardiac function in the hearts of individual patients, this study addresses the feasibility of creating echocardiography-derived maps of regional myocardial fiber structure for entire, intact, excised sheep hearts. Backscatter data were obtained from apical echocardiographic images acquired with a clinical ultrasonic imaging system and used to determine local fiber orientations in each of seven hearts. Systematic acquisition across the entire heart volume provided information sufficient to give a complete map for each heart. Results from the echocardiography-derived fiber maps compare favorably with corresponding results derived from diffusion tensor magnetic resonance imaging. The results of this study provide evidence of the feasibility of using echocardiographic methods to generate individualized whole heart fiber maps for patients.

Investigation of the effects of myocardial anisotropy for shear wave elastography using impulsive force and harmonic vibration

The myocardium is known to be an anisotropic medium where the muscle fiber orientation changes through the thickness of the wall. Shear wave elastography methods use propagating waves which are measured by ultrasound or magnetic resonance imaging (MRI) techniques to characterize the mechanical properties of various tissues. Ultrasound- or MR-based methods have been used and the excitation frequency ranges for these various methods cover a large range from 24-500 Hz. Some of the ultrasound-based methods have been shown to be able to estimate the fiber direction. We constructed a model with layers of elastic, transversely isotropic materials that were oriented at different angles to simulate the heart wall in systole and diastole. We investigated the effect of frequency on the wave propagation and the estimation of fiber direction and wave speeds in the different layers of the assembled models. We found that waves propagating at low frequencies such as 30 or 50 Hz showed low sensitivity to the fiber direction but also had substantial bias in estimating the wave speeds in the layers. Using waves with higher frequency content (>200 Hz) allowed for more accurate fiber direction and wave speed estimation. These results have particular relevance for MR- and ultrasound-based elastography applications in the heart.

Shear wave vibrometry evaluation in transverse isotropic tissue mimicking phantoms and skeletal muscle

Ultrasound radiation force-based methods can quantitatively evaluate tissue viscoelastic material properties. One of the limitations of the current methods is neglecting the inherent anisotropy nature of certain tissues. To explore the phenomenon of anisotropy in a laboratory setting, we created two phantom designs incorporating fibrous and fishing line material with preferential orientations. Four phantoms were made in a cube-shaped mold; both designs were arranged in multiple layers and embedded in porcine gelatin using two different concentrations (8%, 14%). An excised sample of pork tenderloin was also studied. Measurements were made in the phantoms and the pork muscle at different angles by rotating the phantom with respect to the transducer, where 0° and 180° were defined along the fibers, and 90° and 270° across the fibers. Shear waves were generated and measured by a Verasonics ultrasound system equipped with a linear array transducer. For the fibrous phantom, the mean and standard deviations of the shear wave speeds along (0°) and across the fibers (90°) with 8% gelatin were 3.60  ±  0.03 and 3.18  ±  0.12 m s(-1) and with 14% gelatin were 4.10  ±  0.11 and 3.90  ±  0.02 m s(-1). For the fishing line material phantom, the mean and standard deviations of the shear wave speeds along (0°) and across the fibers (90°) with 8% gelatin were 2.86  ±  0.20 and 2.44  ±  0.24 m s(-1) and with 14% gelatin were 3.40  ±  0.09 and 2.84  ±  0.14 m s(-1). For the pork muscle, the mean and standard deviations of the shear wave speeds along the fibers (0°) at two different locations were 3.83  ±  0.16 and 3.86  ±  0.12 m s(-1) and across the fibers (90°) were 2.73  ±  0.18 and 2.70  ±  0.16 m s(-1), respectively. The fibrous and fishing line gelatin-based phantoms exhibited anisotropy that resembles that observed in the pork muscle.

Reliable protocol for shear wave elastography of lower limb muscles at rest and during passive stretching

Development of shear wave elastography gave access to non-invasive muscle stiffness assessment in vivo. The aim of the present study was to define a measurement protocol to be used in clinical routine for quantifying the shear modulus of lower limb muscles. Four positions were defined to evaluate shear modulus in 10 healthy subjects: parallel to the fibers, in the anterior and posterior aspects of the lower limb, at rest and during passive stretching. Reliability was first evaluated on two muscles by three operators; these measurements were repeated six times. Then, measurement reliability was compared in 11 muscles by two operators; these measurements were repeated three times. Reproducibility of shear modulus was 0.48 kPa and repeatability was 0.41 kPa, with all muscles pooled. Position did not significantly influence reliability. Shear wave elastography appeared to be an appropriate and reliable tool to evaluate the shear modulus of lower limb muscles with the proposed protocol.

Characterization of transverse isotropy in compressed tissue-mimicking phantoms

Tissues such as skeletal muscle and kidneys have well-defined structure that affects the measurements of mechanical properties. As an approach to characterize the material properties of these tissues, different groups have assumed that they are transversely isotropic (TI) and measure the shear wave velocity as it varies with angle with respect to the structural architecture of the organ. To refine measurements in these organs, it is desirable to have tissue-mimicking phantoms that exhibit similar anisotropic characteristics. Some approaches involve embedding fibers into a material matrix. However, if a homogeneous solid is under compression due to a static stress, an acoustoelastic effect can manifest that makes the measured wave velocities change with the compression stress. We propose to exploit this characteristic to demonstrate that stressed tissue mimicking phantoms can be characterized as a TI material. We tested six phantoms made with different concentrations of gelatin and agar. Stress was applied by the weight of a water container centered on top of a plate on top of the phantom. A linear array transducer and a V-1 Verasonics system were used to induce and measure shear waves in the phantoms. The shear wave motion was measured using a compound plane wave imaging technique. Autocorrelation was applied to the received in-phase/quadrature data. The shear wave velocity, c, was estimated using a Radon transform method. The transducer was mounted on a rotating stage so measurements were made every 10° over a range of 0° to 360°, where the stress is applied along 0° to 180° direction. The shear moduli were estimated. A TI model was fit to the data and the fractional anisotropy was evaluated. This approach can be used to explore many configurations of transverse isotropy with the same phantom, simply by applying stress to the tissue-mimicking phantom.

4-D ultrafast shear-wave imaging

Over the last ten years, shear wave elastography (SWE) has seen considerable development and is now routinely used in clinics to provide mechanical characterization of tissues to improve diagnosis. The most advanced technique relies on the use of an ultrafast scanner to generate and image shear waves in real time in a 2-D plane at several thousands of frames per second. We have recently introduced 3-D ultrafast ultrasound imaging to acquire with matrix probes the 3-D propagation of shear waves generated by a dedicated radiation pressure transducer in a single acquisition. In this study, we demonstrate 3-D SWE based on ultrafast volumetric imaging in a clinically applicable configuration. A 32 × 32 matrix phased array driven by a customized, programmable, 1024-channel ultrasound system was designed to perform 4-D shear-wave imaging. A matrix phased array was used to generate and control in 3-D the shear waves inside the medium using the acoustic radiation force. The same matrix array was used with 3-D coherent plane wave compounding to perform high-quality ultrafast imaging of the shear wave propagation. Volumetric ultrafast acquisitions were then beamformed in 3-D using a delay-and-sum algorithm. 3-D volumetric maps of the shear modulus were reconstructed using a time-of-flight algorithm based on local multiscale cross-correlation of shear wave profiles in the three main directions using directional filters. Results are first presented in an isotropic homogeneous and elastic breast phantom. Then, a full 3-D stiffness reconstruction of the breast was performed in vivo on healthy volunteers. This new full 3-D ultrafast ultrasound system paves the way toward real-time 3-D SWE.

Characterization of transverse isotropy in compressed tissue-mimicking phantoms

Tissues such as skeletal muscle and kidneys have well-defined structure that affects the measurements of mechanical properties. As an approach to characterize the material properties of these tissues, different groups have assumed that they are transversely isotropic (TI) and measure the shear wave velocity as it varies with angle with respect to the structural architecture of the organ. To refine measurements in these organs, it is desirable to have tissue-mimicking phantoms that exhibit similar anisotropic characteristics. Some approaches involve embedding fibers into a material matrix. However, if a homogeneous solid is under compression due to a static stress, an acoustoelastic effect can manifest that makes the measured wave velocities change with the compression stress. We propose to exploit this characteristic to demonstrate that stressed tissue mimicking phantoms can be characterized as a TI material. We tested six phantoms made with different concentrations of gelatin and agar. Stress was applied by the weight of a water container centered on top of a plate on top of the phantom. A linear array transducer and a V-1 Verasonics system were used to induce and measure shear waves in the phantoms. The shear wave motion was measured using a compound plane wave imaging technique. Autocorrelation was applied to the received in-phase/quadrature data. The shear wave velocity, c, was estimated using a Radon transform method. The transducer was mounted on a rotating stage so measurements were made every 10° over a range of 0° to 360°, where the stress is applied along 0° to 180° direction. The shear moduli were estimated. A TI model was fit to the data and the fractional anisotropy was evaluated. This approach can be used to explore many configurations of transverse isotropy with the same phantom, simply by applying stress to the tissue-mimicking phantom.

Role of multimodality cardiac imaging in the management of patients with hypertrophic cardiomyopathy: an expert consensus of the European Association of Cardiovascular Imaging Endorsed by the Saudi Heart Association

Taking into account the complexity and limitations of clinical assessment in hypertrophic cardiomyopathy (HCM), imaging techniques play an essential role in the evaluation of patients with this disease. Thus, in HCM patients, imaging provides solutions for most clinical needs, from diagnosis to prognosis and risk stratification, from anatomical and functional assessment to ischaemia detection, from metabolic evaluation to monitoring of treatment modalities, from staging and clinical profiles to follow-up, and from family screening and preclinical diagnosis to differential diagnosis. Accordingly, a multimodality imaging (MMI) approach (including echocardiography, cardiac magnetic resonance, cardiac computed tomography, and cardiac nuclear imaging) is encouraged in the assessment of these patients. The choice of which technique to use should be based on a broad perspective and expert knowledge of what each technique has to offer, including its specific advantages and disadvantages. Experts in different imaging techniques should collaborate and the different methods should be seen as complementary, not as competitors. Each test must be selected in an integrated and rational way in order to provide clear answers to specific clinical questions and problems, trying to avoid redundant and duplicated information, taking into account its availability, benefits, risks, and cost.

Viscoelasticity in Achilles tendonopathy: quantitative assessment by using real-time shear-wave elastography

PURPOSE

To investigate the differences in viscoelastic properties between normal and pathologic Achilles tendons (ATs) by using real-time shear-wave elastography (SWE).

MATERIALS AND METHODS

The institutional review board approved this study, and written informed consent was obtained from 25 symptomatic patients and 80 volunteers. One hundred eighty ultrasonographic (US) and SWE studies of ATs without tendonopathy and 30 studies of the middle portion of the AT in patients with tendonopathy were assessed prospectively. Each study included data sets acquired at B-mode US (tendon morphology and cross-sectional area) and SWE (axial and sagittal mean velocity and relative anisotropic coefficient) for two passively mobilized ankle positions. The presence of AT tears at B-mode US and signal-void areas at SWE were noted.

RESULTS

Significantly lower mean velocity was shown in tendons with tendonopathy than in normal tendons in the relaxed position at axial SWE (P < .001) and in the stretched position at sagittal (P < .001) and axial (P = .0026) SWE. Tendon softening was a sign of tendonopathy in relaxed ATs when the mean velocity was less than or equal to 4.06 m · sec(-1) at axial SWE (sensitivity, 54.2%; 95% confidence interval [CI]: 32.8, 74.4; specificity, 91.5%; 95% CI: 86.3, 95.1) and less than or equal to 5.70 m · sec(-1) at sagittal SWE (sensitivity, 41.7%; 95% CI: 22.1, 63.3; specificity, 81.8%; 95% CI: 75.3, 87.2) and in stretched ATs, when the mean velocity was less than or equal to 4.86 m · sec(-1) at axial SWE (sensitivity, 66.7%; 95% CI: 44.7, 84.3; specificity, 75.6%; 95% CI: 68.5, 81.7) and less than or equal to 14.58 m · sec(-1) at sagittal SWE (sensitivity, 58.3%; 95% CI: 36.7, 77.9; specificity, 83.5%; 95% CI: 77.2, 88.7). Anisotropic results were not significantly different between normal and pathologic ATs. Six of six (100%) partial-thickness tears appeared as signal-void areas at SWE.

CONCLUSION

Whether the AT was relaxed or stretched, SWE helped to confirm and quantify pathologic tendon softening in patients with tendonopathy in the midportion of the AT and did not reveal modifications of viscoelastic anisotropy in the tendon. Tendon softening assessed by using SWE appeared to be highly specific, but sensitivity was relatively low.

Ultrasound backscatter tensor imaging (BTI): analysis of the spatial coherence of ultrasonic speckle in anisotropic soft tissues

The assessment of fiber architecture is of major interest in the progression of myocardial disease. Recent techniques such as magnetic resonance diffusion tensor imaging (MR-DTI) or ultrasound elastic tensor imaging (ETI) can derive the fiber directions by measuring the anisotropy of water diffusion or tissue elasticity, but these techniques present severe limitations in a clinical setting. In this study, we propose a new technique, backscatter tensor imaging (BTI), which enables determination of the fiber directions in skeletal muscles and myocardial tissues, by measuring the spatial coherence of ultrasonic speckle. We compare the results to ultrasound ETI. Acquisitions were performed using a linear transducer array connected to an ultrasonic scanner mounted on a motorized rotation device with angles from 0° to 355° by 5° increments to image ex vivo bovine skeletal muscle and porcine left ventricular myocardial samples. At each angle, multiple plane waves were transmitted and the backscattered echoes recorded. The coherence factor was measured as the ratio of coherent intensity over incoherent intensity of backscattered echoes. In skeletal muscle, maximal/minimal coherence factor was found for the probe parallel/perpendicular to the fibers. In myocardium, the coherence was assessed across the entire myocardial thickness, and the position of maxima and minima varied transmurally because of the complex fibers distribution. In ETI, the shear wave speed variation with the probe angle was found to follow the coherence variation. Spatial coherence can thus reveal the anisotropy of the ultrasonic speckle in skeletal muscle and myocardium. BTI could be used on any type of ultrasonic scanner with rotating phased-array probes or 2-D matrix probes for noninvasive evaluation of myocardial fibers.

Layer-specific radiofrequency ultrasound-based strain analysis in a porcine model of ischemic cardiomyopathy validated by a geometric model

Local layer-specific myocardial deformation after myocardial infarction (MI) has not been studied extensively although the sub-endocardium is more vulnerable to ischemia and interstitial fibrosis deposition. Radiofrequency (RF) ultrasound-based analysis could provide superior layer-specific radial strain estimation compared with clinically available deformation imaging techniques. In this study, we used RF-based myocardial deformation measurements to investigate layer-specific differences between healthy and damaged myocardium in a porcine model of chronic MI. RF data were acquired epicardially in healthy (n = 21) and infarcted (n = 5) regions of a porcine chronic MI model 12 wk post-MI. Radial and longitudinal strains were estimated in the sub-endocardial, mid-wall and sub-epicardial layers of the left ventricle. Collagen content was quantified in three layers of healthy and infarcted regions in five pigs. An analytical geometric model of the left ventricle was used to theoretically underpin the radial deformation estimated in different myocardial layers. Means ± standard errors of the peak radial and longitudinal strain estimates of the sub-endocardial, mid-wall and sub-epicardial layers of the healthy and infarcted tissue were: 82.7 ± 5.2% versus 39.9 ± 10.8% (p = 0.002), 63.6 ± 3.3% versus 38.8 ± 7.7% (p = 0.004) and 34.3 ± 3.0% versus 35.1 ± 5.2% (p = 0.9), respectively. The radial strain gradient between the sub-endocardium and the sub-epicardium had decreased 12 wk after MI, and histologic examination revealed the greatest increases in collagen in the sub-endocardial and mid-wall layers. Comparable normal peak radial strain values were found by geometric modeling when input values were derived from the in vivo measurements and literature. In conclusion, the estimated strain values are realistic and indicate that sub-endocardial radial strain in healthy tissue can amount to 80%. This high value can be explained by the cardiac geometry, as was illustrated by geometric modeling. After MI, strain values were decreased and collagen content was increased in the sub-endocardial and mid-wall layers. Layer-specific peak radial strain can be assessed by RF strain estimation and clearly differs between healthy and infarcted tissue. Although the relationship between tissue stiffness and tissue strain is not strictly local, this novel technique provides a valuable way to assess layer-specific regional cardiac function in a variety of myocardial diseases.

Acoustic waves in medical imaging and diagnostics

Up until about two decades ago acoustic imaging and ultrasound imaging were synonymous. The term ultrasonography, or its abbreviated version sonography, meant an imaging modality based on the use of ultrasonic compressional bulk waves. Beginning in the 1990s, there started to emerge numerous acoustic imaging modalities based on the use of a different mode of acoustic wave: shear waves. Imaging with these waves was shown to provide very useful and very different information about the biological tissue being examined. We discuss the physical basis for the differences between these two basic modes of acoustic waves used in medical imaging and analyze the advantages associated with shear acoustic imaging. A comprehensive analysis of the range of acoustic wavelengths, velocities and frequencies that have been used in different imaging applications is presented. We discuss the potential for future shear wave imaging applications.

Length and activation dependent variations in muscle shear wave speed

Muscle stiffness is known to vary as a result of a variety of disease states, yet current clinical methods for quantifying muscle stiffness have limitations including cost and availability. We investigated the capability of shear wave elastography (SWE) to measure variations in gastrocnemius shear wave speed induced via active contraction and passive stretch. Ten healthy young adults were tested. Shear wave speeds were measured using a SWE transducer positioned over the medial gastrocnemius at ankle angles ranging from maximum dorsiflexion to maximum plantarflexion. Shear wave speeds were also measured during voluntary plantarflexor contractions at a fixed ankle angle. Average shear wave speed increased significantly from 2.6 to 5.6 m s(-1) with passive dorsiflexion and the knee in an extended posture, but did not vary with dorsiflexion when the gastrocnemius was shortened in a flexed knee posture. During active contractions, shear wave speed monotonically varied with the net ankle moment generated, reaching 8.3 m s(-1) in the maximally contracted condition. There was a linear correlation between shear wave speed and net ankle moment in both the active and passive conditions; however, the slope of this linear relationship was significantly steeper for the data collected during passive loading conditions. The results show that SWE is a promising approach for quantitatively assessing changes in mechanical muscle loading. However, the differential effect of active and passive loading on shear wave speed makes it important to carefully consider the relevant loading conditions in which to use SWE to characterize in vivo muscle properties.

Extracting Cardiac Myofiber Orientations from High Frequency Ultrasound Images

Cardiac myofiber plays an important role in stress mechanism during heart beating periods. The orientation of myofibers decides the effects of the stress distribution and the whole heart deformation. It is important to image and quantitatively extract these orientations for understanding the cardiac physiological and pathological mechanism and for diagnosis of chronic diseases. Ultrasound has been wildly used in cardiac diagnosis because of its ability of performing dynamic and noninvasive imaging and because of its low cost. An extraction method is proposed to automatically detect the cardiac myofiber orientations from high frequency ultrasound images. First, heart walls containing myofibers are imaged by B-mode high frequency (>20 MHz) ultrasound imaging. Second, myofiber orientations are extracted from ultrasound images using the proposed method that combines a nonlinear anisotropic diffusion filter, Canny edge detector, Hough transform, and K-means clustering. This method is validated by the results of ultrasound data from phantoms and pig hearts.

Imaging myocardial fiber orientation using polarization sensitive optical coherence tomography

Knowledge of myocardial fiber architecture is essential towards understanding heart functions. We demonstrated in this study a method to map cardiac muscle structure using the local optical axis obtained from polarization-sensitive optical coherence tomography (PSOCT). An algorithm was developed to extract the true local depth-resolved optical axis, retardance, and diattenuation from conventional round-trip results obtained in a Jones matrix-based PSOCT system. This method was applied to image the myocardial fiber orientation in a bovine heart muscle sample.