Use of solution-processed zinc oxide to prevent the breakdown in silver nanowire networks

Highly Transmittance, Mechanical, Thermally Stable Silver Nanowires Network Using ZnO Nanoparticles

This research addresses challenges with silver nanowires (Ag NWs) as transparent conductive electrodes (TCEs) and heaters in commercial devices. Here, zinc oxide nanoparticles (ZnO NPs) are first reported as a protective layer for Ag NWs. Multi-physics simulations confirm enhanced thermal stability due to improved heat dissipation, temperature distribution, and thermal conductivity from ZnO. When Ag NWs are surrounded by air, heat transfers mainly through convection and radiation because of air's low conduction coefficient. Encasing Ag NWs in ZnO enhances heat transfer to the ZnO surface, accelerating cooling and dissipating more heat into the atmosphere via convection. The results show composite's efficiency in the Joule effect, maintaining a consistent temperature of 78 °C for 700 s after 500 bending cycles, a significant improvement over Ag NWs operating for only 5 s at 80 °C. Additionally, the composite film exhibited exceptional performance, including a sheet resistance of 9.8 Ω sq-1 and an optical transmittance of 96.96 %, outperforming Ag NWs, which have a sheet resistance of 12 Ω sq-1 and a transmittance of 94.11%. The combination of enhanced electrical, thermal, and mechanical stability, along with impressive optical properties, makes Ag NWs/ZnO NPs a promising candidate for transparent conductive electrode materials in various applications.

Accelerated and outdoor weathering of silver nanowire transparent conductors under electrical stress in pseudo-modules

In realistic applications, silver nanowires (AgNWs) are encapsulated in optoelectrical devices to function as transparent conductors and electrodes. Environmental stressors along with the essential electrical stress are inevitably harmful to the AgNWs inside the devices. Herein, to investigate the degradation behavior discrepancy between materials-level and device-level tests, we adopted pseudo-module to mimic the encapsulation. The pseudo-module allows the application of electrical stress and facilitates the interim specimen access for materials characterization through assembly-disassembly. Indoor accelerated and outdoor weathering tests with applied electrical stress to the pseudo-module encapsulated AgNW networks were performed. The impaired optoelectrical properties and morphological changes of AgNWs due to multiple or individual stressor(s) are investigated. Results indicate UVA exposure at elevated temperature coupled with electrical stress is responsible for the electrical failure of AgNW networks. Sulfidation that depresses optical transparency of AgNW networks is prone to occur at lower temperature. This work provides unambiguous degradation behaviors of AgNWs inside encapsulants, helping to improve the design of AgNWs related optoelectrical devices in the applications of solar irradiation environments.

Novel Insights into Inkjet Printed Silver Nanowires Flexible Transparent Conductive Films

Silver nanowire (AgNWs) inks for inkjet printing were prepared and the effects of the solvent system, wetting agent, AgNWs suspension on the viscosity, surface tension, contact angle between ink droplet and poly(ethylene) terephthalate (PET) surface, and pH value of AgNWs ink were discussed. Further, AgNWs flexible transparent conductive films were fabricated by using inkjet printing process on the PET substrate, and the effects of the number printing layer, heat treatment temperature, drop frequency, and number of nozzle on the microstructures and photoelectric properties of AgNWs films were investigated in detail. The experimental results demonstrated that the 14-layer AgNWs printed film heated at 60 °C and 70 °C had an average sheet resistance of 13 Ω∙sq⁻¹ and 23 Ω∙sq⁻¹ and average transparency of 81.9% and 83.1%, respectively, and displayed good photoelectric performance when the inkjet printing parameters were set to the voltage of 20 V, number of nozzles of 16, drop frequency of 7000 Hz, droplet spacing of 15 μm, PET substrate temperatures of 40 °C and nozzles of 35 °C during printing, and heat treatment at 60 °C for 20 min. The accumulation and overflow of AgNWs at the edges of the linear pattern were observed, which resulted in a decrease in printing accuracy. We successfully printed the heart-shaped pattern and then demonstrated that it could work well. This showed that the well-defined pattern with good photoelectric properties can be obtained by using an inkjet printing process with silver nanowires ink as inkjet material.