Energy recycling under ambient illumination for internet-of-things using metal/oxide/metal-based colorful organic photovoltaics

Editorial: Focus on green nanomaterials for a sustainable internet of things

In the dynamic landscape of the Internet of Things (IoT), where smart devices are reshaping our world, nanomaterials can play a pivotal role in ensuring the IoT's sustainability. These materials are poised to redefine the development of smart devices, not only enabling cost-effective fabrication but also unlocking novel functionalities. As the IoT is set to encompass an astounding number of interconnected devices, the demand for environmentally friendly nanomaterials takes center stage. ThisFocus Issuespotlights cutting-edge research that explores the intersection of nanomaterials and sustainability. The collection delves deep into this critical nexus, encompassing a wide range of topics, from fundamental properties to applications in devices (e.g. sensors, optoelectronic synapses, energy harvesters, memory components, energy storage devices, and batteries), aspects concerning circularity and green synthesis, and an array of materials comprising organic semiconductors, perovskites, quantum dots, nanocellulose, graphene, and two-dimensional semiconductors. Authors not only showcase advancements but also delve into the sustainability profile of these materials, fostering a responsible endeavour toward a green IoT future.

High-Performance and Stable Perovskite Solar Cells Using Carbon Quantum Dots and Upconversion Nanoparticles

Upconversion nanoparticles (UCNPs) and carbon quantum dots (CQDs) have recently received a lot of attention as promising materials to improve the stability and efficiency of perovskite solar cells (PSCs). This is because they can passivate the surfaces of perovskite-sensitive materials and act as a spectrum converter for sunlight. In this study, we mixed and added both promising nanomaterials to PSC layers at the ideal mixing ratios. When compared to the pristine PSCs, the fabricated PSCs showed improved power conversion efficiency (PCE), from 16.57% to 20.44%, a higher photocurrent, and a superior fill factor (FF), which increased from 70% to 75%. Furthermore, the incorporation of CQDs into the manufactured PSCs shielded the perovskite layer from water contact, producing a device that was more stable than the original.

Alwan N, Velkin VI, Sharipov P, Safaraliev M, Chen X. Experimental Study on Performance Enhancement of a Photovoltaic Module Incorporated with CPU Heat Pipe-A 5E Analysis

As is already known, solar photovoltaic (PV) technology is a widely accepted technology for power generation worldwide. However, it is scientifically proven that its power output decreases with an increase in the temperature of the PV module. Such an important issue is controlled by adopting a number of cooling mechanisms for the PV module. The present experimental study assesses the effect of a fanless CPU heat pipe on the performance of a PV module. The experiment was conducted in June in real weather conditions in Yekaterinburg, Russian Federation. The comparative analysis of two PV panels (i.e., cooled, and uncooled) based on the electrical energy, exergy performance, economic, embodied energy and energy payback (5E) for the two systems is presented and discussed. The key results from the study are that the average temperature reduction from the cooling process is 6.72 °C. The average power for the cooled panel is 11.39 W against 9.73 W for the uncooled PV panel; this represents an increase of 1.66 W for the cooled module. Moreover, the average improvements in the electrical efficiency, and embodied energy recorded for a cooled PV panel 2.98%, and 438.52 kWh, respectively. Furthermore, the calculations of the levelized cost of energy (LCE) for the cooled PV panel indicate that it can range from 0.277-0.964 USD/kWh, while that for the uncooled PV panel also ranges from 0.205-0.698 USD/kWh based on the number of days of operation of the plant.

Surfactant Tween 20 Controlled Perovskite Film Fabricated by Thermal Blade Coating for Efficient Perovskite Solar Cells

In recent years, additive engineering has received considerable attention for the fabrication of high-performance perovskite solar cells (PSCs). In this study, a non-ionic surfactant, polyoxyethylene (20) sorbitan monolaurate (Tween 20), was added as an additive into the MAPbI₃ perovskite layer, and the thermal-assisted blade-coating method was used to fabricate a high-quality perovskite film. The Tween 20 effectively passivated defects and traps in the MAPbI₃ perovskite films. Such a film fabricated with an appropriate amount of Tween 20 on the substrate showed a higher photoluminescence (PL) intensity and longer carrier lifetime. At the optimal concentration of 1.0 mM Tween 20, the performance of the PSC was apparently enhanced, and the champion PSC demonstrated a PCE of 18.80%. Finally, this study further explored and compared the effect on the device performance and ambient stability of the MAPbI₃ perovskite film prepared by the spin-coating method and the thermal-assisted blade coating.

Cathode Interlayer Engineering for Efficient Organic Solar Cells under Solar Illumination and Light-Emitting Diode Lamp

Organic solar cells (OSCs) have become a potential energy source for indoor light harvesting in recent years as they have witnessed a record power conversion efficiency (PCE) of over 30% under indoor lights. Among various strategies, interlayer engineering is one of the important factors in improving the performance of OSCs. Here, we reported an efficient OSC based on PM6:Y6 photoactive layer showing an excellent PCE of ~22% and ~14% under light-emitting diode (LED, 1000-lx) and 1-sun (AM1.5 G) conditions, respectively. The performance of OSCs was optimized by systematically investigating the optical, electrochemical, and morphological characteristics of three different cathode interlayers (CILs) named as: PEIE, ZnO, and ZnO/PEIE (bilayer). The high transmittance (~90%), suitable work function (~4.1 eV), and improved surface morphology (RMS: 2.61 nm) of the bilayer CIL contributes in improving the performance of OSCs. In addition, the suppressed charge recombination and improved charge carrier transport are attributed to high shunt resistance and appropriate energy levels alignment between photoactive layer and bilayer CIL. The findings in the study might provide guidelines for designing novel interlayers in the development of efficient OSCs for different illumination conditions.

2D MXene: A Potential Candidate for Photovoltaic Cells? A Critical Review

The 2D transition metal carbides/nitrides (2D MXenes) are a versatile class of 2D materials for photovoltaic (PV) systems. The numerous advantages of MXenes, including their excellent metallic conductivity, high optical transmittance, solution processability, tunable work-function, and hydrophilicity, make them suitable for deployment in PV technology. This comprehensive review focuses on the synthesis methodologies and properties of MXenes and MXene-based materials for PV systems. Titanium carbide MXene (Ti3 C2 Tx ), a well-known member of the MXene family, has been studied in many PV applications. Herein, the effectiveness of Ti3 C2 Tx as an additive in different types of PV cells, and the synergetic impact of Ti3 C2 Tx as an interfacial material on the photovoltaic performance of PV cells, are systematically examined. Subsequently, the utilization of Ti3 C2 Tx as a transparent conductive electrode, and its influence on the stability of the PV cells, are discussed. This review also considers problems that emerged from previous studies, and provides guidelines for the further exploration of Ti3 C2 Tx and other members of the 2D MXene family in PV technology. This timely study is expected to provide comprehensive understanding of the current status of MXenes, and to set the direction for the future development in 2D material design and processing for PVs.

Ambient Light Energy Harvesting and Numerical Modeling of Non-Linear Phenomena

Ambient light is an energy-harvesting source that can recharge a battery with less human interaction and can be used to prolong the operational time of the Internet of Things, e.g., mobile phones and wearable devices. Available light energy is insufficient for directly charging mobile phones and wearable devices, but it can supplement batteries to power some low-energy-consuming critical functions of the wearable device, especially in low-power consumption wearables. However, in an emergency scenario when the battery’s operational time is not sufficient or a battery charging source is unavailable, a solution is required to extend the limited battery span for mobile and wearable devices. This work presents the bottlenecks and new advancements in the commercialization of photovoltaics for smartphones and wearable technologies based on ambient light energy harvesting. A new technique, in which a smartphone cover is used as a solar concentrator to enhance light energy harvesting associated with algorithms, is experimentally demonstrated. Our research outcomes show that solar concentrators can improve light intensity by approximately 1.85 and 1.43 times at 90° and 71° angles, respectively, thus harvesting more ambient light energy at 2500 lx light intensity in a typical office environment. Type-1 PV and Type-2 PV cells were able to charge the additional battery in 8 h under 2500 lx lighting intensity in an indoor office environment. A system and logic algorithm technique is presented to efficiently transfer harvested light energy to perform low-energy consumption operations in a device, in order to improve the operational time of the device’s battery.

Optimizing Device Structure of PTB7-Th:PNDI-T10 Bulk Heterojunction Polymer Solar Cells by Enhancing Optical Absorption

Using the optical transfer matrix method, we optimized the layered structure of a conventional and an inverted BHJ OSC with the active layer made of blended PTB7-Th:PNDI-T10 by maximizing the optical absorption and, hence, the JSC. The maximum JSC thus obtained from the optimised structure of the inverted OSC was 139 Am−2 and that of the conventional OSC was 135 Am−2. Simulation of the electric field distribution in both inverted and conventional OSCs showed that the formation of a single CIP was obtained in the active layer of thickness 105 nm in both OSCs. As the light incidents from the ITO side, it was found that excitons were generated more closely to ITO electrode, which favors the efficient charge transport and collection at the opposite electrodes in the inverted OSC, which produces higher JSC.

Performance-Enhancing Sulfur-Doped TiO2 Photoanodes for Perovskite Solar Cells

High-performance electron transport layer (ETL) anode generally needs to form a uniform dense layer with suitable conduction band position and good electron transport properties. The TiO2 photoanode is primarily applied as the ETL because it is low-cost, has diverse thin-film preparation methods and has good chemical stability. However, pure TiO2 is not an ideal ETL because it lacks several important criteria, such as low conductivity and conduction band mismatch with compositional-tailored perovskite. Thus, TiO2 is an inefficient photo-anode or ETL for high-performance perovskite devices. In this study, sulfur as dopant in the TiO2 photo-anode thin film is used to fabricate solid-state planar perovskite solar cells in relatively high humidity (40–50%). The deposited S-doped thin film improves the power conversion efficiency (PCE) of the device to 6.0%, with the un-doped TiO2 producing a PCE of 5.1% in the best device. Improvement in PCE is due to lower recombination and higher photocurrent density, resulting in 18% increase in PCE (5.1–6.0%).

Elucidating Charge Generation in Green-Solvent Processed Organic Solar Cells

Organic solar cells have the potential to become the cheapest form of electricity. Rapid increase in the power conversion efficiency of organic solar cells (OSCs) has been achieved with the development of non-fullerene small-molecule acceptors. Next generation photovoltaics based upon environmentally benign “green solvent” processing of organic semiconductors promise a step-change in the adaptability and versatility of solar technologies and promote sustainable development. However, high-performing OSCs are still processed by halogenated (non-environmentally friendly) solvents, so hindering their large-scale manufacture. In this perspective, we discuss the recent progress in developing highly efficient OSCs processed from eco-compatible solvents, and highlight research challenges that should be addressed for the future development of high power conversion efficiencies devices.

Investigation of Dye Dopant Influence on Electrooptical and Morphology Properties of Polymeric Acceptor Matrix Dedicated for Ternary Organic Solar Cells

The publication presents the results of investigations of the influence of dye dopant on the electrooptical and morphology properties of a polymeric donor:acceptor mixture. Ternary thin films (polymer:dye:fullerene) were investigated for potential application as an active layer in organic solar cells. The aim of the research is to determine the effect of selected dye materials (dye D131, dye D149, dye D205, dye D358) on the three-component layer and their potential usefulness as an additional donor in ternary cells, based on P3HT donor and PC71BM acceptor. UV-vis spectroscopy studies were performed, and absorption and luminescence spectra were determined. Ellipsometry parameters for single dye and ternary layers have been measured. The analyses were performed using the Raman spectroscopy method, and the Raman spectra of the mixtures and single components have been determined. Organic layers were prepared and studied using scanning electron microscope and atomic force microscope. For dyes, ultraviolet photoelectron spectroscopy and X-ray photoelectron spectroscopy studies were carried out and the ternary system was presented and analyzed in terms of energy bands.

Voltage Rise Regulation with a Grid Connected Solar Photovoltaic System

Renewable Distributed Generation (RDG), when connected to a Distribution Network (DN), suffers from power quality issues because of the distorted currents drawn from the loads connected to the network over generation of active power injection at the Point of Common Coupling (PCC). This research paper presents the voltage rise regulation strategy at the PCC to enhance power quality and continuous operation of RDG, such as Photovoltaic Arrays (PVAs) connected to a DN. If the PCC voltage is not regulated, the penetration levels of the renewable energy integration to a DN will be limited or may be ultimately disconnected in the case of a voltage rise issue. The network is maintained in both unity power factor and voltage regulation mode, depending on the condition of the voltage fluctuation occurrences at the PCC. The research investigation shows that variation in the consumer’s loads (reduction) causes an increase in the power generated from the PVA, resulting in an increase in the grid current amplitude, reduction in the voltage of the feeder impedance and an increase in the phase voltage amplitude at the PCC. When the system is undergoing unity power factor mode, PCC voltage amplitude tends to rises with the loads. Its phase voltage amplitude rises above an acceptable range with no-loads which are not in agreement, as specified in the IEEE-1547 and Southern Africa grid code prerequisite. Incremental Conduction with Integral Regulator bases (IC + PI) are employed to access and regulate PVA generation, while the unwanted grid current distortions are attenuated from the network using an in-loop second order integral filtering circuit algorithm. Hence, the voltage rise at the PCC is mitigated through the generation of positive reactive power to the grid from the Distribution Static Compensator (DSTATCOM), thereby regulating the phase voltage. The simulation study is carried out in a MATLAB/Simulink environment for PVA performance.

Lithium-Based Upconversion Nanoparticles for High Performance Perovskite Solar Cells

In this work, we report an easy, efficient method to synthesize high quality lithium-based upconversion nanoparticles (UCNPs) which combine two promising materials (UCNPs and lithium ions) known to enhance the photovoltaic performance of perovskite solar cells (PSCs). Incorporating the synthesized YLiF₄:Yb,Er nanoparticles into the mesoporous layer of the PSCs cells, at a certain doping level, demonstrated a higher power conversion efficiency (PCE) of 19%, additional photocurrent, and a better fill factor (FF) of 82% in comparison to undoped PSCs (PCE = ~16.5%; FF = 71%). The reported results open a new avenue toward efficient PSCs for renewable energy applications.

Simulating the Performance of a Formamidinium Based Mixed Cation Lead Halide Perovskite Solar Cell

With the aim of decreasing the number of experiments to obtain a perovskite solar cell (PSC) with maximum theoretical efficiency, in this paper, PSC performance was studied using the program solar cell capacitance simulator (SCAPS-1D). The PSC with the architecture ITO/TiO₂/perovskite/spiro-MeOTAD/Au was investigated, while the selected perovskite was mixed cation Rb_0.05Cs_0.1FA_0.85PbI₃. The analysis was based on an experimentally prepared solar cell with a power conversion efficiency of ~7%. The PSC performance, verified by short-circuit current density (J_sc), open-circuit voltage (V_oc), fill factor (FF) and power conversion efficiency (PCE), was studied by optimization of the simulation parameters responsible for improvement of the cell operation. The optimized parameters were absorber layer thickness, doping, defect concentration and the influence of the resistivity (the net effect of ohmic loss, R_s and the leakage current loss represented by the resistivity, R_shunt). The results of SCAPS-1D simulations estimated the theoretical power conversion efficiency of 15% for our material. We have showed that the main contribution to improvement of solar cell efficiency comes with lowering ohmic resistivity of the cell as well as doping and defect concentration, because their concentration is proportional to recombination rate.