Solid State Ionics: from Michael Faraday to green energy-the European dimension

Systematic study of ionic conduction in silver iodide/mesoporous alumina composites 2: effects of silver bromide doping

In our preceding paper (Y. Fukui et al., Phys. Chem. Chem. Phys., 2023, 25, 25594-25602), we reported a systematic study of the Ag+-ion conducting behaviour of silver iodide (AgI)-loaded mesoporous aluminas (MPAs) with different pore diameters and AgI-loading ratios. By optimising the control parameters, the Ag+-ion conductivity has reached 7.2 × 10-4 S cm-1 at room temperature, which is more than three orders of magnitude higher than that of bulk AgI. In the present study, the effect of silver bromide (AgBr)-doping in the AgI/MPA composites on Ag+-ion conductivity is systematically investigated for the first time, using variable-temperature powder X-ray diffraction, differential scanning calorimetry, and electrochemical impedance spectroscopy measurements. The AgBr-doped AgI/MPA composites, AgI-AgBr/MPA, formed a homogeneous β/γ-AgI-structured solid solution (β/γ-AgIss) for the composites with AgBr ≤ 10 mol%, above which the composites underwent a phase separation into β/γ-AgIss and face-centred cubic AgBr solid solutions (AgBrss). The onset temperature of the exothermic peaks attributed to the transition from α-AgI-structured solid-solution phase to β/γ-AgIss or AgBrss decreased with increasing the AgBr-doping ratio. The room-temperature ionic conductivity of the AgI-AgBr/MPA composites exhibited a volcano-type dependence on the AgBr-doping ratio with the highest value (1.6 × 10-3 S cm-1) when the AgBr content was 10 mol%. This value is more than twice as high as that of the highest conducting AgI/MPA found in our previous study.

Systematic study of ionic conduction in silver iodide/mesoporous alumina composites 1: effects of pore size and filling level

A systematic study of Ag+-ion conducting behavior in Ag+-loaded porous materials was conducted over the entire sub-10 nm region for the first time. The effects of the pore diameter of mesoporous aluminas (MPAs) and the amount of silver iodide (AgI) loaded into MPAs were investigated using N2 gas adsorption/desorption, powder X-ray diffraction, differential scanning calorimetry, and electrochemical impedance spectroscopy measurements. Confinement of AgI in the mesoporous space lowers the phase transition temperature between the β/γ- and α-phases relative to that of bulk AgI. The AgI-loading into the MPAs with smaller pores led to a more significant decrease in the transition temperature, possibly because the smaller AgI nanoparticles in the pores must have a higher surface energy to stabilize the high-temperature phase. The room-temperature ionic conductivity exhibits a volcano-type dependence on the pore diameter with the highest value when AgI was loaded into MPA with a pore diameter of 7.1 nm (7.2 × 10-4 S cm-1 at room temperature). Concerning the 7.1 nm-MPA, the room-temperature ionic conductivity was the highest for the nearly fully occupied composite, which is more than three orders of magnitude higher than that of the bulk AgI. The present study reveals that the Ag+-ion conductivity in AgI/MPA composites can be controlled by optimizing the pore diameter of MPA and the AgI-loading ratio.

Progress and Perspective of Glass-Ceramic Solid-State Electrolytes for Lithium Batteries

The all-solid-state lithium battery (ASSLIB) is one of the key points of future lithium battery technology development. Because solid-state electrolytes (SSEs) have higher safety performance than liquid electrolytes, and they can promote the application of Li-metal anodes to endow batteries with higher energy density. Glass-ceramic SSEs with excellent ionic conductivity and mechanical strength are one of the main focuses of SSE research. In this review paper, we discuss recent advances in the synthesis and characterization of glass-ceramic SSEs. Additionally, some discussions on the interface problems commonly found in glass-ceramic SSEs and their solutions are provided. At the end of this review, some drawbacks of glass-ceramic SSEs are summarized, and future development directions are prospected. We hope that this review paper can help the development of glass-ceramic solid-state electrolytes.

Opportunities of Flexible and Portable Electrochemical Devices for Energy Storage: Expanding the Spotlight onto Semi-solid/Solid Electrolytes

The ever-increasing demand for flexible and portable electronics has stimulated research and development in building advanced electrochemical energy devices which are lightweight, ultrathin, small in size, bendable, foldable, knittable, wearable, and/or stretchable. In such flexible and portable devices, semi-solid/solid electrolytes besides anodes and cathodes are the necessary components determining the energy/power performances. By serving as the ion transport channels, such semi-solid/solid electrolytes may be beneficial to resolving the issues of leakage, electrode corrosion, and metal electrode dendrite growth. In this paper, the fundamentals of semi-solid/solid electrolytes (e.g., chemical composition, ionic conductivity, electrochemical window, mechanical strength, thermal stability, and other attractive features), the electrode-electrolyte interfacial properties, and their relationships with the performance of various energy devices (e.g., supercapacitors, secondary ion batteries, metal-sulfur batteries, and metal-air batteries) are comprehensively reviewed in terms of materials synthesis and/or characterization, functional mechanisms, and device assembling for performance validation. The most recent advancements in improving the performance of electrochemical energy devices are summarized with focuses on analyzing the existing technical challenges (e.g., solid electrolyte interphase formation, metal electrode dendrite growth, polysulfide shuttle issue, electrolyte instability in half-open battery structure) and the strategies for overcoming these challenges through modification of semi-solid/solid electrolyte materials. Several possible directions for future research and development are proposed for going beyond existing technological bottlenecks and achieving desirable flexible and portable electrochemical energy devices to fulfill their practical applications. It is expected that this review may provide the readers with a comprehensive cross-technology understanding of the semi-solid/solid electrolytes for facilitating their current and future researches on the flexible and portable electrochemical energy devices.

Nanoionics from Biological to Artificial Systems: An Alternative Beyond Nanoelectronics

Ion transport under nanoconfined spaces is a ubiquitous phenomenon in nature and plays an important role in the energy conversion and signal transduction processes of both biological and artificial systems. Unlike the free diffusion in continuum media, anomalous behaviors of ions are often observed in nanostructured systems, which is governed by the complex interplay between various interfacial interactions. Conventionally, nanoionics mainly refers to the study of ion transport in solid-state nanosystems. In this review, to extent this concept is proposed and a new framework to understand the phenomena, mechanism, methodology, and application associated with ion transport at the nanoscale is put forward. Specifically, here nanoionics is summarized into three categories, i.e., biological, artificial, and hybrid, and discussed the characteristics of each system. Compared with nanoelectronics, nanoionics is an emerging research field with many theoretical and practical challenges. With this forward-looking perspective, it is hoped that nanoionics can attract increasing attention and find wide range of applications as nanoelectronics.

Fundamentals and Principles of Solid-State Electrochemical Sensors for High Temperature Gas Detection

The rapid development of science, technology, and engineering in the 21st century has offered a remarkable rise in our living standards. However, at the same time, serious environmental issues have emerged, such as acid rain and the greenhouse effect, which are associated with the ever-increasing need for energy consumption, 85% of which comes from fossil fuels combustion. From this combustion process, except for energy, the main greenhouse gases-carbon dioxide and steam-are produced. Moreover, during industrial processes, many hazardous gases are emitted. For this reason, gas-detecting devices, such as electrochemical gas sensors able to analyze the composition of a target atmosphere in real time, are important for further improving our living quality. Such devices can help address environmental issues and inform us about the presence of dangerous gases. Furthermore, as non-renewable energy sources run out, there is a need for energy saving. By analyzing the composition of combustion emissions of automobiles or industries, combustion processes can be optimized. This review deals with electrochemical gas sensors based on solid oxide electrolytes, which are employed for the detection of hazardous gasses at high temperatures and aggressive environments. The fundamentals, the principle of operation, and the configuration of potentiometric, amperometric, combined (amperometric-potentiometric), and mixed-potential gas sensors are presented. Moreover, the results of previous studies on carbon oxides (COx), nitrogen oxides (NOx), hydrogen (H2), oxygen (O2), ammonia (NH3), and humidity (steam) electrochemical sensors are reported and discussed. Emphasis is given to sensors based on oxygen ion and proton-conducting electrolytes.

Fuzzy logic: about the origins of fast ion dynamics in crystalline solids

Nuclear magnetic resonance offers a wide range of tools to analyse ionic jump processes in crystalline and amorphous solids. Both high-resolution and time-domain [Formula: see text], [Formula: see text], [Formula: see text], [Formula: see text] NMR helps throw light on the origins of rapid self-diffusion in materials being relevant for energy storage. It is well accepted that [Formula: see text] ions are subjected to extremely slow exchange processes in compounds with strong site preferences. The loss of this site preference may lead to rapid cation diffusion, as is also well known for glassy materials. Further examples that benefit from this effect include, e.g. cation-mixed, high-entropy fluorides [Formula: see text], Li-bearing garnets ([Formula: see text]) and thiophosphates such as [Formula: see text]. In non-equilibrium phases site disorder, polyhedra distortions, strain and the various types of defects will affect both the activation energy and the corresponding attempt frequencies. Whereas in [Formula: see text] ([Formula: see text]) cation mixing influences F anion dynamics, in [Formula: see text] ([Formula: see text]) the potential landscape can be manipulated by anion site disorder. On the other hand, in the mixed conductor [Formula: see text] cation-cation repulsions immediately lead to a boost in [Formula: see text] diffusivity at the early stages of chemical lithiation. Finally, rapid diffusion is also expected for materials that are able to guide the ions along (macroscopic) pathways with confined (or low-dimensional) dimensions, as is the case in layer-structured [Formula: see text] or [Formula: see text]. Diffusion on fractal systems complements this type of diffusion. This article is part of the Theo Murphy meeting issue 'Understanding fast-ion conduction in solid electrolytes'.

Paper-Based Device for Sweat Chloride Testing Based on the Photochemical Response of Silver Halide Nanocrystals

A new method for the determination of chloride anions in sweat is described. The novelty of the method relies on the different photochemical response of silver ions and silver chloride crystals when exposed to UV light. Silver ions undergo an intense colorimetric transition from colorless to dark grey-brown due to the formation of nanosized Ag while AgCl exhibits a less intense color change from white to slightly grey. The analytical signal is obtained as mean grey value of color intensity on the paper surface and is expressed as the absolute difference between the signal of the blank (i.e., in absence of chloride) and the sample (i.e., in the presence of chloride). The method is simple to perform (addition of sample, incubation in the absence of light, irradiation, and offline measurement in a flatbed scanner), does not require any special signal processing steps (the color intensity is directly measured from a constant window on the paper surface without any imager processing) and is performed with minimum sample volume (2 μL). The method operates within a large chloride concentration range (10–140 mM) with good detection limits (2.7 mM chloride), satisfactory recoveries (95.2–108.7%), and reproducibility (<9%). Based on these data the method could serve as a potential tool for the diagnosis of cystic fibrosis through the determination of chloride in human sweat.

In situ electron holography for characterizing Li ion accumulation in the interface between electrode and solid-state-electrolyte

The reconstructed phase image of the in situ holography unravels Li ion behavior in the electrolyte beneath the electrode during the charging process.

Perspectives for Ag2S NIR-II nanoparticles in biomedicine: from imaging to multifunctionality

Research on near-infrared (NIR) bioimaging has progressed very quickly in the past few years, as fluorescence imaging is reaching a credible implementation as a preclinical technique. The applications of NIR bioimaging in theranostics have contributed to its increasing impact. This has brought about the development of novel technologies and, simultaneously, of new contrast agents capable of acting as efficient NIR optical probes. Among these probes, Ag₂S nanoparticles (NPs) have attracted increasing attention due to their temperature-sensitive NIR-II emission, which can be exploited for deep-tissue imaging and thermometry, and their heat delivery capabilities. This multifunctionality makes Ag₂S NPs ideal candidates for theranostics. This review presents a critical analysis of the synthesis routes, properties and optical features of Ag₂S NPs. We also discuss the latest and most remarkable achievements enabled by these NPs in preclinical imaging and theranostics, together with a critical assessment of their potential to face forthcoming challenges in biomedicine.

Fluoride-Ion Batteries: On the Electrochemical Stability of Nanocrystalline La0.9Ba0.1F2.9 against Metal Electrodes

Over the past years, ceramic fluorine ion conductors with high ionic conductivity have stepped into the limelight of materials research, as they may act as solid-state electrolytes in fluorine-ion batteries (FIBs). A factor of utmost importance, which has been left aside so far, is the electrochemical stability of these conductors with respect to both the voltage window and the active materials used. The compatibility with different current collector materials is important as well. In the course of this study, tysonite-type La0.9Ba0.1F2.9, which is one of the most important electrolyte in first-generation FIBs, was chosen as model substance to study its electrochemical stability against a series of metal electrodes viz. Pt, Au, Ni, Cu and Ag. To test anodic or cathodic degradation processes we carried out cyclic voltammetry (CV) measurements using a two-electrode set-up. We covered a voltage window ranging from −1 to 4 V, which is typical for FIBs, and investigated the change of the response of the CVs as a function of scan rate (2 mV/s to 0.1 V/s). It turned out that Cu is unstable in combination with La0.9Ba0.1F2.9, even before voltage was applied. The cells with Au and Pt electrodes show reactions during the CV scans; in the case of Au the irreversible changes seen in CV are accompanied by a change in color of the electrode as investigated by light microscopy. Ag and Ni electrodes seem to suffer from contact issues which, most likely, also originate from side reactions with the electrode material. The experiments show that the choice of current collectors in future FIBs will become an important topic if we are to develop long-lasting FIBs. Most likely, protecting layers between the composite electrode material and the metal current collector have to be developed to prevent any interdiffusion or electrochemical degradation processes.

First universality of conductivity spectra in superprotonic (NH4)3H(SO4)2 single crystal

We present the frequency study of electric conductivity in the superprotonic single crystal in a wide temperature range covering the superprotonic phase I and the low conducting, ferroelastic phase II. The data below microwave frequencies are analyzed using the Summerfield scaling method to check for presence of the first universality. The scaled conductivity obtained from the raw experimental data plotted versus scaled frequency do not show the universality because it contains, in a low temperature range, steps related to relaxational dielectric contribution. The contribution, evidenced by a temperature study of frequency dependence of ε″, presumably comes from polar ammonia and therefore does not reflect properties of the hopping motion of mobile ions. To get rid of it, the conductivity is calculated using the impedance data obtained from the fitting procedure of the Nyquist plots. The resulting scaled ac conductivity plot forms a single curve in a wide temperature range. Thus, (NH₄)₃H(SO₄)₂ meets criteria for the first universality, despite the fact that it undergoes the structural, superionic phase transition in the temperature range studied.

Spatial confinement – rapid 2D F− diffusion in micro- and nanocrystalline RbSn2F5

NMR and conductivity spectroscopy reveal 2D diffusion in both microcrystalline and nanocrystalline RbSn₂F₅.

Stretchable Ionics - A Promising Candidate for Upcoming Wearable Devices

As many devices for human utility aim for fast and convenient communication with users, superb electronic devices are demonstrated to serve as hardware for human-machine interfaces in wearable forms. Wearable devices for daily healthcare and self-diagnosis offer more human-like properties unconstrained by deformation. In this sense, stretchable ionics based on flexible and stretchable hydrogels are on the rise as another means to develop wearable devices for bioapplications for two main reasons: i) ionic currents and choosing the same signal carriers for biological areas, and ii) the adoption of hydrogel ionic conductors, which are intrinsically stretchable materials with biocompatibility. Here, the current status of stretchable ionics and future applications are introduced, whose positive effects can be magnified by stretchable ionics.

Paper-based devices for biothiols sensing using the photochemical reduction of silver halides

This study describes the development of paper-based devices for the determination of biothiols. The devices are inexpensive (composed of paper and silver halide particles), and the analytical protocol is easily executable with minimum technical expertise and without the need of specialized equipment; the user has to add a test sample, illuminate the device with a UV lamp, and read the color change of the sensing area using a simple imaging device (i.e., cell-phone camera) or a bare eye. The detection mechanism of the assay is based on the biothiols-mediated photoreduction of nanometer-sized silver chloride particles deposited on the surface of paper; photoreduced silver chloride particles have a grayish coloration that depends on the concentration of biothiols in the tested solution. This is the first time that the UV-mediated photoreduction of solid silver halides particles is used for analytical purposes. The performance of the devices has been tested on the detection of total biothiols content of artificial body fluids and protein-free human blood plasma samples, and the results were satisfactory in terms of sensitivity, selectivity, recoveries and reproducibility.

Magnetic Control of Magneto-Electrochemical Cell and Electric Double Layer Transistor

A magneto-electrochemical cell and an electric double layer transistor (EDLT), each containing diluted [Bmim]FeCl₄ solution, have been controlled by applying a magnetic field in contrast to the control of conventional field effect devices by an applied electric field. A magnetic field of several hundred mT generated by a small neodymium magnet is sufficient to operate magneto-electrochemical cells, which generate an electromotive force of 130 mV at maximum. An EDLT composed of hydrogen-terminated diamond was also operated by applying a magnetic field. Although it showed reversible drain current modulation with a magnetoresistance effect of 503%, it is not yet advantageous for practical application. Magnetic control has unique and interesting characteristics that are advantageous for remote control of electrochemical behavior, the application for which conventional electrochemical devices are not well suited. Magnetic control is opening a door to new applications of electrochemical devices and related technologies.

Solid state ionics: a Japan perspective

The 70-year history of scientific endeavor of solid state ionics research in Japan is reviewed to show the contribution of Japanese scientists to the basic science of solid state ionics and its applications. The term 'solid state ionics' was defined by Takehiko Takahashi of Nagoya University, Japan: it refers to ions in solids, especially solids that exhibit high ionic conductivity at a fairly low temperature below their melting points. During the last few decades of exploration, many ion conducting solids have been discovered in Japan such as the copper-ion conductor Rb₄Cu₁₆I₇Cl₁₃, proton conductor SrCe_1-x Y _x O₃, oxide-ion conductor La_0.9Sr_0.9Ga_0.9Mg_0.1O₃, and lithium-ion conductor Li₁₀GeP₂S₁₂. Rb₄Cu₁₆I₇Cl₁₃ has a conductivity of 0.33 S cm^-1 at 25 °C, which is the highest of all room temperature ion conductive solid electrolytes reported to date, and Li₁₀GeP₂S₁₂ has a conductivity of 0.012 S cm^-1 at 25 °C, which is the highest among lithium-ion conductors reported to date. Research on high-temperature proton conducting ceramics began in Japan. The history, the discovery of novel ionic conductors and the story behind them are summarized along with basic science and technology.

Conductivity Optimization of Tysonite-type La1-xBaxF3-x Solid Electrolytes for Advanced Fluoride Ion Battery

Use of lithium ion batteries is currently the method of choice when it comes to local stationary storage of electrical energy. In the search for an alternative system, fluoride ion batteries (FIBs) emerge as a candidate due to their high theoretical capacity, and no lithium is needed for its operation. To improve the cycling performance and lower the working temperature of a solid-state battery, one of the critical components is the electrolyte, which needs advanced performance. This paper aims at developing an electrolyte with enhanced ionic conductivity for fluoride ions, to be used in a FIB. Tysonite La_1-xBa_xF_3-x (0 ≤ x ≤ 0.15) solid solutions were synthesized by a facile wet chemical method, and its ionic conductivity was analyzed using electrochemical impedance spectroscopy. A composition study shows that the conductivity reaches a maximum of 1.26 × 10^-4 S·cm^-1 at 60 °C for the La_0.95Ba_0.05F_2.95 pellet sintered at 800 °C for 20 h, which is 1 order of magnitude higher than that for the as-prepared pellet and 2 times higher than the conductivity of sintered ball-milled batches. The reason for this dramatic increment is the more efficient decrement of grain boundary resistance upon sintering. Morphological, chemical, and structural characterizations of solid electrolytes were studied by X-ray diffraction, scanning electron microscopy , energy dispersive X-ray spectroscopy, physisorption by the Brunauer-Emmett-Teller method, and transmission electron microscopy. Electrochemical testing was carried out for the FIB cell using La_0.95Ba_0.05F_2.95 as electrolyte due to its highest conductivity among the compositions, Ce as anode, and BiF₃ as a cathode. The cycling performance was found to be considerably improved when compared to our earlier work, which used the ball-milled electrolyte.

Time-reversal symmetry for systems in a constant external magnetic field

The time-reversal properties of charged systems in a constant external magnetic field are reconsidered in this paper. We show that the evolution equations of the system are invariant under a new symmetry operation that implies a new signature property for time-correlation functions under time reversal. We then show how these findings can be combined with a previously identified symmetry to determine, for example, null components of the correlation functions of velocities and currents and of the associated transport coefficients. These theoretical predictions are illustrated by molecular dynamics simulations of superionic AgI.

Low Dimensional String-like Relaxation Underpins Superionic Conduction in Fluorites and Related Structures

Among the superionic conductors that show a Faraday transition – the continuous increase in the ionic conductivity over a range of temperatures – the fluorite structures have enjoyed incisive examinations over the past four decades; yet the fundamental nature of superionicity has remained largely inconclusive. Departing from the traditional quasi-static defect framework, we provide weighty evidence for string-like dynamical structures that govern the fast ion conduction process in fluorites. We show that lower temperatures encourage the growth of longer but slowly relaxing strings and vice-versa – a direct manifestation of heterogeneous dynamics. Remarkably, the ionic conductivity is inversely correlated to the lifetime of the ions that participate in the strings and not explicitly to the ion population. Our analysis methodology, which resolves a long-standing disagreement on defect structures and the mechanism of ionic transport in fcc fluorite structures, is well-positioned to describe the dynamics of low dimensional conduction in a larger class of superionic conductors.

Imidazolium cation transportation in a 1-D coordination polymer

We synthesized a coordination polymer, [EtMeIm][Cu(bpy)(Me₂PO₄)₃], containing an anionic 1-D chain and an ethyl methyl imidazolium cation.

Energy storage through intercalation reactions: electrodes for rechargeable batteries

Electrochemical energy storage has been an important enabling technology for modern electronics of all kinds, and will grow in importance as more electric vehicles and grid-scale storage systems are deployed. We briefly review the history of intercalation electrodes and basic concepts pertaining to batteries based on intercalation reactions. Then we summarize how the critical performance metrics—energy density, power density, safety and stability—relate back to electrode materials properties, and how these materials properties are related to fundamental chemical and physical structure relationships highlighted with the most recent research advancement. Challenges and avenues for further research have been highlighted throughout.

Effect of Ionic Conductivity on Response Speed of SrTiO3-Based All-Solid-State Electric-Double-Layer Transistor

An all-solid-state electric-double-layer transistor (EDLT) with a Y-stabilized ZrO₂ (YSZ) proton conductor/SrTiO₃ (STO) single crystal has been fabricated to investigate ionic conductivity effect on the response speed, which should be a key parameter for development of next-generation EDLTs. The drain current exhibited a 4-order-of-magnitude increment by electrostatic carrier doping at the YSZ/STO interface due to ion migration, and the behavior strongly depended on the operation temperature. An Arrhenius-type plot of the ionic conductivity (σ(i)) in the YSZ and t(c)⁻¹, which is a current-rise time needed for charge accumulation at the YSZ/STO interface, shows a synchronized variation, indicating a proportional relationship between the two parameters. Analysis of the σ(i)-t(c) diagram shows that, in contrast to conventional EDLTs, the response speed should reach picosecond order at room temperature by using extreme miniaturization and superionic conductors. Furthermore, the diagram indicates that plenty of solid electrolytes, which have not been used due to the lack of criteria for evaluation, can be a candidate for all-solid-state EDLTs exceeding the carrier density of conventional EDLTs, even though the response speed becomes comparably lower than those of FETs.

Correlated fluorine diffusion and ionic conduction in the nanocrystalline F(-) solid electrolyte Ba(0.6)La(0.4)F(2.4)-(19)F T1(ρ) NMR relaxation vs. conductivity measurements

Chemical reactions induced by mechanical treatment may give access to new compounds whose properties are governed by chemical metastability, defects introduced and the size effects present. Their interplay may lead to nanocrystalline ceramics with enhanced transport properties being useful to act as solid electrolytes. Here, the introduction of large amounts of La into the cubic structure of BaF2 served as such an example. The ion transport properties in terms of dc-conductivity values of the F(-) anion conductor Ba1-xLaxF2+x (here with x = 0.4) considerably exceed those of pure, nanocrystalline BaF2. So far, there is only little knowledge about activation energies and jump rates of the elementary hopping processes. Here, we took advantage of both impedance spectroscopy and (19)F NMR relaxometry to get to the bottom of ion jump diffusion proceeding on short-range and long-range length scales in Ba0.6La0.4F2.4. While macroscopic transport is governed by an activation energy of 0.55 to 0.59 eV, the elementary steps of hopping seen by NMR are characterised by much smaller activation energies. Fortunately, we were able to deduce an F(-) self-diffusion coefficient by the application of spin-locking NMR relaxometry.

In situ and nonvolatile photoluminescence tuning and nanodomain writing demonstrated by all-solid-state devices based on graphene oxide

In situ and nonvolatile tuning of photoluminescence (PL) has been achieved based on graphene oxide (GO), the PL of which is receiving much attention because of various potential applications of the oxide (e.g., display, lighting, and nano-biosensor). The technique is based on in situ and nonvolatile tuning of the sp(2) domain fraction to the sp(3) domain fraction (sp(2)/sp(3) fraction) in GO through an electrochemical redox reaction achieved by solid electrolyte thin films. The all-solid-state variable PL device was fabricated by GO and proton-conducting mesoporous SiO2 thin films, which showed an extremely low PL background. The device successfully tuned the PL peak wavelength in a very wide range from 393 to 712 nm, covering that for chemically tuned GO, by adjusting the applied DC voltage within several hundred seconds. We also demonstrate the sp(2)/sp(3) fraction tuning using a conductive atomic force microscope. The device achieved not only writing, but also erasing of the sp(2)/sp(3)-fraction-tuned nanodomain (both directions operation). The combination of these techniques is applicable to a wide range of nano-optoelectronic devices including nonvolatile PL memory devices and on-demand rewritable biosensors that can be integrated into nano- and microtips which are transparent, ultrathin, flexible, and inexpensive.