Morphological and atomic analytical studies on enamel and dentin irradiated by an erbium, chromium:YSGG laser

Clinical effects of laser-based cavity preparation on class V resin-composite fillings

The aim of the present clinically controlled two-year study was to investigate the influence of laser-based cavity preparation on the long-term performance of Class V resin-composite fillings. Class V non-carious lesions (n = 75) were randomly assigned to two test and one control group. Cavities in both test groups were prepared using an Er,Cr:YSGG laser (Waterlase MD, Biolase, Irvine, California, USA). The device was operated at 3 W (150 mJ, 30 J/cm²), 50% water, 60% air, 30 Hz in H mode. Subsequently, laser-prepared tooth surfaces in test group I (n = 21) were additionally conditioned by acid etching (etch-and-rinse). Laser-prepared cavities of test group II (n = 21) received no additional acid conditioning. After application of an adhesive, all cavities were restored using the resin-composite Venus®. For cavities in the control group (n = 33) conventional diamond burs were used for preparation which was followed by an etch-and-rinse step, too. The fillings were evaluated immediately (baseline) and after 6, 12 and 24 months of wear according to the C-criteria of the USPHS-compatible CPM-index. The results showed that after 24 month of wear, laser-preparation was associated with fillings of high clinical acceptability. Compared to conventional bur-based treatment, laser-based cavity preparation resulted in fillings with high marginal integrity and superior marginal ledge configurations (p = 0.003). Furthermore, laser-preparation combined with additional acid-conditioning (test group I) resulted in fillings with the best marginal integrity and the lowest number in marginal discoloration, especially at the enamel-composite margins (p = 0.044). In addition, total loss of fillings was also less frequently observed in both laser groups as compared to the control. The results clearly demonstrate that laser-based cavity preparation will benefit the clinical long-time performance of Class V resin-composite fillings. Furthermore, additional acid-conditioning after laser preparation is of advantage.

Application of Er,Cr:YSGG laser versus photopolymerization after silver diamine fluoride in primary teeth

Examine the effect of dental curing light and laser treatments applied after Silver Diamine Fluoride (SDF) on dentin hardness in carious primary molars. This in-vitro study consisted of 30 extracted primary molars with caries extending into dentin without pulpal involvement. The collected teeth were randomly divided into three groups: group 1: received SDF then Sub-ablative low-energy of Er,Cr:YSGG laser, group 2: received SDF followed by application of curing light for 40 s, group 3: had SDF treatment only. In all groups, 38% Ag (NH3)2F SDF was used. Vickers hardness test was performed on sound dentin below carious lesion. Kruskal-Wallis Test was used to determine the mean difference in dentin hardness of the groups at 5% Significance level using SPSS software. Surface hardness of sound dentin below the carious lesion was statistically significantly higher in the laser + SDF group (891.24 ± 37.33 kgf/mm2) versus the two other groups (Light cure + SDF = 266.65 ± 90.81 kgf/mm2 and SDF only = 117.91 ± 19.19 kgf/mm2) with p-value ≤ 0.001. Although Photopolymerization of SDF increases the surface hardness of sound dentin below the carious lesion, applying laser after SDF has the highest surface hardness due to the laser's sub-ablation of dentin.

Shear bond strength of acid and laser conditioned enamel and dentine to composite resin restorations: An in vitro study

Objective

To compare the shear bond strength of enamel or dentin conditioned with either Er,Cr:YSGG (erbium, chromium: yttrium–scandium–gallium–garnet) laser or phosphoric acid to composite resin restoration.

Material and methods

Forty posterior human extracted teeth were used. After mesiodistal sectioning of the teeth crowns, the samples were randomly divided into two groups—in the first group (E), bonding was performed on the enamel after roughening and in the second group (D), the enamel was removed and bonding was performed on the dentin. These groups were further randomly divided into two subgroups according to the type of etching (n = 20 each). In the acid‐etched groups (EA and DA), the surfaces were etched with 37% phosphoric acid. In the laser‐conditioned groups (EL and DL), the surfaces were conditioned with Er,Cr:YSGG laser. Total‐etch adhesive system was used to bond all the 80 specimens resin composite. The composite was vertically light‐cured, and the specimens were subjected to a shear bond strength test. Modes of bond failure were determined with a stereomicroscope.

Results

The highest shear bond strength was observed for the DA group (16.25 ± 1.10 MPa, p < 0.0001), whereas the lowest was observed for the DL group (8.56 ± 0.67 MPa). The adhesive failure mode was the most frequently observed in all groups.

Conclusions

The shear bond strength of composite resin bonded to enamel and dentin etched with phosphoric acid was higher than when conditioned with Er,Cr:YSGG laser. Thus, laser conditioning is not recommended.

Er,Cr:YSGG Laser Energy Delivery: Pulse and Power Effects on Enamel Surface and Erosive Resistance

BACKGROUND

High power lasers have been suggested as a useful tool for dental caries and erosion prevention due to the increase of enamel acid resistance.

OBJECTIVE

to evaluate the effect of Er,Cr:YSGG (erbium,chromium:yttrium, scandium, gallium, garnet) laser irradiation pulse frequency and power on enamel surface and acid erosion resistance.

METHODS

By combining pulse frequency (5-75 Hz) and power settings (0.10-1.00 W), 20 irradiated groups and one nonirradiated control group were tested. A total of 63 bovine enamel blocks (n = 3/group) were prepared for surface hardness and roughness evaluation, performed in three phases: baseline, after irradiation, and after erosive challenge. Enamel blocks were irradiated with Er,Cr:YSGG laser with MZ8 tip (iPlus; Waterlase, Biolase, CA) for 30 sec according to experimental group and submitted. Erosive challenge consisted of four cycles alternating immersion in 0.01 M HCl (5 mL/mm²; 2 min; at 37°C) and immersion in artificial saliva for 3 h. Analysis of variance (three-way ANOVA), Tukey's test, and Pearson correlation were performed for the statistical analysis (p < 0.05).

RESULTS

After irradiation, groups irradiated with pulse frequency of 10 and 15 Hz showed a decrease in surface hardness. After erosive challenge, 5 and 75 W groups showed increase in surface hardness; 0.25, 0.5, 0.75, and 1 W groups showed minor alterations in surface roughness.

CONCLUSIONS

the irradiation of Er,Cr:YSGG laser with different parameters of power and pulse frequency settings may alter enamel surface and erosive resistance differently. Pulse frequency of 30 Hz and power of 0.50 W was considered the best parameter to prevent enamel acid erosion.

Effect of 2.94 µm Er: YAG laser on the chemical composition of hard tissues

The aim was to investigate the effect of the Er-YAG laser radiation on morphology and chemical composition of enamel, dentin, and bone. The specimens of the three groups were irradiated with a very long pulse mode (VLP) of 2.94 µm Er-YAG laser with 100 mJ pulse energy and energy density of 8.42 J/ c m 2 for 30 s, at a repetition rate of 15 Hz. The organic and inorganic content of the samples were investigated by Fourier Transforms Infrared spectroscopy (FTIR). The morphological characteristics were investigated with scanning electron microscopy (SEM) and elemental analysis (calcium and phosphorus) with energy-dispersive X-ray spectroscopy (EDX). FTIR data were analyzed with a One-Way ANCOVA test and EDX data with the independent sample t-test. Following the laser radiation, FTIR showed a significant decrease in the organic content of all tissues. The weight percentage (wt %) calcium content of dentin and bone increased significantly following irradiation with a p-value of .002 for both tissues, but the wt % of phosphorus content was not influenced significantly. The morphological alterations expressed signs of fusion in all the samples.

Effect of Er,Cr:YSGG laser application in the treatment of experimental periodontitis

The purpose of this study was to evaluate the influence of an erbium, chromium:yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser in the absence or presence of manual scaling and root planning (SRP) for the treatment of induced periodontitis in rats. Ligatures were placed in the subgingival region of the maxillary first molar. After a 7-day period, the ligatures were removed, and 40 rats were randomly divided into four groups (G), as follows: (GI) no treatment, (GII) scaling and root planning (SRP) with curettes, (GIII) Er,Cr:YSGG laser irradiation and (GIV) SRP with curettes followed by Er,Cr:YSGG laser irradiation. Seven and 30 days after the treatment, the animals were sacrificed and histologic, histometric and immunohistochemistry analyses were performed. All groups showed similar histopathological characteristics during the evaluation period. The histometric analysis was confirmed using Bonferroni and paired t tests. At 7 and 30 days, groups II, III and IV exhibited greater bone formation in the furcation area when compared to group I (p < 0.0001; p < 0.05). During the 7-day period, the groups irradiated with the laser (III and IV) showed a statistically larger new bone area than the group treated with SRP (II) (p < 0.01). Immunohistochemistry analysis revealed that the control group exhibited a higher expression of tartrate-resistant acid phosphatase (TRAP) and the receptor activator of nuclear factor κΒ ligand (RANKL) when compared to groups II, III and IV (p < 0.05). All treatments were able to reduce the inflammatory processes, consequently enabling the repair of periodontal tissues. The results achieved with the application of the Er,Cr:YSGG laser suggest that this laser can stimulate greater bone formation, especially over a shorter period of time.

Effects of Er:YAG laser irradiation and manipulation treatments on dentin components, part 2: energy-dispersive X-ray fluorescence spectrometry study

The effects of laser etching, decontamination, and storage treatments on dentin components were studied by energy-dispersive X-ray fluorescence spectrometry (EDXRF). Thirty bovine incisors were prepared to expose the dentin surface and then divided into two main groups based upon the decontamination process and storage procedure: autoclaved (group A, n=15) or stored in aqueous thymol solution (group B, n=15). The surfaces of the dentin slices were schematically divided into four areas, with each one corresponding to a treatment subgroup. The specimens were either etched with phosphoric acid (control subgroup) or irradiated with erbium-doped yttrium-aluminum-garnet (Er:YAG) laser (subgroups: I-80 mJ, II-120 mJ, and III-180 mJ). Samples were analyzed by micro-EDXRF, yielding three spectra for each area (before and after treatment). Surface mappings covering an area of 80x60 points with steps of 20 mum were also performed on selected specimens. The amount of Ca and P in group A specimens decreased significantly (P<0.05) after the acid etching and the CaP ratio increased (P<0.001). Er:YAG laser-etching using lower laser energies did not produce significant changes in dentin components. The mapping data support the hypothesis that acid etching on dentin produced a more chemically homogeneous surface and thus a more favorable surface for the diffusion of adhesive monomers.

Construction of a standard test assembly for controlled laser studies in tissues: preliminary study on human bone material

The aim of the study is the construction of a test assembly, which facilitates objective, comparative studies on the cutting performance of lasers in hard tissue. To ensure the applicability of our own construction for the reproducible performance of laser incisions in hard tissue, eleven freshly extracted blocks (2x1.5 cm2) of human bone were prepared with a Er,Cr:YSGG laser by using a handheld handpiece, respectively, using the constructed device for a standardized cutting. A total of 44 cuts were executed. The specimen were then histologically evaluated. The standard test assembly met the requirements concerning the provision of objective results. The findings of the histological evaluation prove the reproducibility of the results. The standard test assembly presented in this paper facilitates comparative studies of different laser systems by reducing subjective influence on the preparation to a minimum. The results of this preliminary study show that the precision of the guiding instrument for laser cutting reduces the error of cut width by 50-fold, from 50 to 1 microm.

Influence of the water content in dental enamel and dentin on ablation with erbium YAG and erbium YSGG lasers

The theory of the ablation of dental hard tissue with erbium lasers is based on a process of thermomechanical interaction, which is explained by the absorption of the radiation in the water component of the tissue. The abrupt evaporation of the water is the cause of tissue fragments being blasted out of the tooth structure. The aim of this study is to examine the effect of the water contained in dental hard tissues on the efficiency of ablation. 192 specimens of both bovine dental enamel and bovine dentin are irradiated with an Er:YAG and an Er,Cr:YSGG laser. Half of the specimens are dehydrated beforehand. Irradiation is carried out in subgroups: without water spray and with water spray at flow rates of 0.8 and 3 mls. The ablated volume is determined following histological preparation. Only in dentin, and then only with irradiation with the Er:YAG laser, is the water contained in the tissue found to have a significant influence (p < 0.0001) on the ablated volume. The water content has no effect on the efficiency of laser ablation in any of the other test groups. In contrast, the externally supplied water always has a significant influence on the effectiveness of the ablation process.

Morphological Study of the Er,Cr:YSGG Laser for Root Canal Preparation in Mandibular Incisors with Curved Root Canals

OBJECTIVE

The objectives of this study were to observe morphological changes of root canal walls and to evaluate the capability of Er,Cr:YSGG laser for preparation of curved mandibular incisor root canals in vitro.

BACKGROUND DATA

There are no published reports on the use of Er,Cr:YSGG laser for curved root canal preparation.

METHODS

Twenty curved mandibular incisor root canals (10 and 15 degrees) were prepared sequentially by laser irradiation at 20 Hz, 2 Wusing two different sizes of fine fiber tips (200 and 320 microm in diameters). After laser irradiation, the teeth were bisected longitudinally, and the specimens were observed by stereoscope and scanning electron microscope (SEM).

RESULTS

Root canal walls of the irradiated areas showed step-like appearances and openings of dentinal tubules, and root canal preparation, having curvatures of less than 10 degrees, could be carried out by this laser irradiation.

CONCLUSIONS

Er,Cr:YSGG laser irradiation is capable of preparing root canals having curvatures of less than 10 degrees.

Morphological comparative study on ablation of dental hard tissues at cavity preparation by Er:YAG and Er,Cr:YSGG lasers

OBJECTIVE

The purpose of this study was to evaluate morphologically the dental hard tissue ablation at the class V cavity preparation by two types of laser devices: Er:YAG and Er,Cr:YSGG lasers in vitro.

BACKGROUND DATA

There have been no reports on the comparative study of dental tissue ablation at cavity preparation by Er:YAG and Er,Cr:YSGG lasers.

METHODS

Twenty-two extracted human mature molar teeth were used in this study and divided into two groups of 11 teeth each. The teeth of the Er:YAG laser-irradiated group were irradiated at the parameters of 250 mJ/pulse and 15 Hz with water spray, and those of the Er,Cr:YSGG laserirradiated group were irradiated at the parameters of 5 Wand 20 Hz with water spray. After cavity preparation, the teeth were dehydrated, coated with platinum, and examined by scanning electron microscopy.

RESULTS

Both of the laser devices were capable of ablating dental hard tissues, but similar, irregular, and rugged surface aspects with different depths were observed. Open dentinal tubules at the cavities prepared by Er,Cr:YSGG laser were more clearly visible than those prepared by Er:YAG laser. Smaller width and stripped surfaces were observed on the cavities prepared by Er,Cr:YSGG laser.

CONCLUSION

The results suggested that there is little difference between the two types of lasers-Er:YAG and Er,Cr:YSGG lasers-morphologically for class V cavity preparation, because both lasers were capable of preparing class V cavities, and the morphological features of the irradiated surfaces were very similar.

Effect of Er:YAG laser on enamel acid resistance: Morphlogical and atomic spectrometry analysis

BACKGROUND AND OBJECTIVES

This study evaluated the effect of Er:YAG laser on enamel acid resistance.

STUDY DESIGN/MATERIALS AND METHODS

Seventy human enamel slabs were randomly divided into seven groups (n = 10): G1, Er:YAG laser (Key Laser 2, KaVo, Germany) 60 mJ, 2 Hz, 33.3 J/cm2 (handpiece no. 2051, non-contact); G2, Er:YAG laser 80 mJ, 2 Hz, 44.4 J/cm2 (handpiece no. 2051, non-contact); G3, Er:YAG laser 120 mJ, 2 Hz, 66.6 J/cm2 (handpiece no. 2051, non-contact); G4, Er:YAG laser 64 mJ, 2 Hz, 20 J/cm2 (handpiece no. 2055, contact); G5, Er:YAG laser 86.4 mJ, 2 Hz, 26.9 J/cm2 (handpiece no. 2055, contact); G6, Er:YAG laser 135 mJ, 2 Hz, 42.2 J/cm2 (handpiece no. 2055, contact); G7, control. After laser irradiation, samples were submitted to an acid challenge. For both the nos. 2051 and 2055 handpieces, irradiation was performed with a water cooled spray (5.0 ml/minutes). The calcium and phosphorous ions delivered from the tooth surface were quantified by atomic emission spectrometry, and morphological analysis of the enamel surface was performed under scanning electron microscopy. Kruskal-Wallis and multiple comparisons tests were applied to distinguish significant differences among the treatments (alpha = 5%).

RESULTS

Groups G1, G2, and G4 presented decreased demineralization. The SEM evaluation revealed different surface alterations as a result of the different energies used.

CONCLUSION

Lower energies can decrease enamel solubility without severe alterations of the enamel.

Erbium lasers in dentistry

Erbium hard tissue lasers have the capability to prepare enamel, dentin, caries, cementum, and bone in addition to cutting soft tissue. The ability of hard tissue lasers to reduce or eliminate vibrations, the audible whine of drills, microfractures, and some of the discomfort that many patients fear and commonly associate with high-speed handpieces is impressive. In addition, these lasers can be used with a reduced amount of local anesthetic for many procedures. Today, these instruments have evolved from their initial use for all classes of cavity preparations to their ability for removing soft tissue, their usefulness in the disinfection of bacteria within endodontic canals, and most recently, as an alternative to the high speed handpiece for the removal of bone in oral and maxillofacial surgery. In addition, recent research has centered on the value of the erbium family of laser wavelengths in periodontics, including the removal of calculus.

Comparative Study of Carious Dentin Removal by Er,Cr:YSGG Laser and Carisolv

OBJECTIVE

The present study aimed to compare carious dentin removal by air turbine, Carisolv and erbium,chromium:yttrium,scandium,gallium,garnet (Er,Cr:YSGG) laser, and examine morphological changes before and after these caries removal techniques under light microscopy and scanning electron microscopy (SEM).

BACKGROUND DATA

Although there have been numerous studies on removing caries by Er,Cr:YSGG laser, none has compared Er,Cr:YSGG laser and Carisolv, or reported on the usage of DIAGNOdent as a diagnostic tool particularly for advanced caries in in vitro experiments.

MATERIALS AND METHODS

Sixty extracted human teeth diagnosed as advanced caries were divided into three groups based on the treatment received, namely air turbine, Carisolv, and Er,Cr:YSGG laser groups. Each group was sub-divided into two in order to examine the results with or without finishing using nylon brush, 15% ethylene diamine tetraacetic acid (EDTA) or low-power laser, respectively. After evaluation by DIAGNOdent, specimens were observed under light microscopy or SEM.

RESULTS

Light microscopic observations varied considerably in the three treatment groups. SEM revealed that the surfaces treated by air turbine were very smooth, but with substantial debris. The Carisolv group exhibited a very rough surface with a thick smear layer, while the Er,Cr:YSGG group demonstrated smooth undulations with little smear layer and debris. Among the finishing techniques, the laser group demonstrated the best efficiency. DIAGNOdent scores supported the results of light microscopy.

CONCLUSION

These results suggest that caries removal by Er,Cr:YSGG laser is very effective even without finishing and DIAGNOdent is useful for diagnosing advanced caries in in vitro experiments.

Morphological changes of bovine mandibular bone irradiated by Er,Cr:YSGG laser: an in vitro study

OBJECTIVE

The purpose of this study was to investigate the morphological changes of bovine mandibular bone following Er,Cr:YSGG laser irradiation in different methods in vitro.

BACKGROUND DATA

Recently, an erbium, chromium/yttrium, scandium, garmet (Er,Cr:YSGG) laser device that emits a laser beam at the wavelength of 2.78 micro m was introduced. This type of infrared laser proved to ablate dental hard tissues effectively. However, the different effects of bone ablation by this laser in different irradiation methods were still unknown.

MATERIALS AND METHODS

Adult bovine mandibular bones were cut into 24 small pieces, 3-4 cm in length. The parameters of Er,Cr:YSGG laser irradiation were as follows: wavelength was 2.78 micro m, pulse duration was 140-200 micro sec, repetition rate was 20 pulse/sec, power was 4 W, spot size was 1.26 x 10(-3) mm(2), and energy density was 160 J/cm(2). Irradiation methods were different in four groups (six specimens in each group): group A, fixed position and contact mode; group B, fixed position and noncontact mode; group C, nonfixed position and contact mode; and group D, nonfixed position and noncontact mode.

RESULTS

Ablation depth in group A was significantly greater than in group B (p < 0.01). In group A, thermal damage was apparent. In group B, C, and D, thermal damage was minimal.

CONCLUSION

Er,Cr:YSGG laser allows for precise surgical bone cutting and ablation with minimal thermal damage to adjacent tissue. Irradiation in different methods may achieve different ablation rates and thermal damage.

Clinical assessment of Er,Cr:YSGG laser application for cavity preparation

In this study, an erbium,chromium:YSGG (Er,Cr:YSGG) laser emitting at a wavelength of 2.78 microm was clinically applied to remove caries and prepare cavities, and the clinical outcome was evaluated. Effective clinical application of Er,Cr:YSGG laser had been expected from previous studies. This study included 44 patients (26 females, 18 males; aged 23-58) with a total of 50 cavity preparations by the Er,Cr:YSGG laser irradiation at 3-6 W with water spray. Patient acceptance and prognosis were evaluated. Most cases (94%) were prepared without anesthesia, and no pain was felt in 34 cases (68%). No adverse reaction was observed in any of the cases, and patient acceptance for this system was favorable. All cases had a good prognosis. In 45 cases (90%), overall clinical evaluation was satisfactory. From the present study, it can be concluded that the Er,Cr:YSGG laser system is an efficient, effective, and safe device for caries removal and cavity preparation.

Effects of erbium,chromium:YSGG laser irradiation on canine mandibular bone

BACKGROUND

Only relatively few reports have described the morphological effects on bone produced by erbium,chromium: yttrium,scandium,gallium,garnet (Er,Cr:YSGG) laser irradiation, and none has investigated the atomic changes or estimated the temperature increases involved. The objectives of this study were to investigate the morphological, atomic, and temperature changes in irradiated areas during and after laser irradiation, and to evaluate the cutting effect on canine mandibular bone in vitro.

METHODS

Two canine mandibular bones were cut into 3 to 5 cm pieces and irradiated by an Er,Cr:YSGG laser utilizing a water-air spray at 5 W and 8 Hz for 10 or 30 seconds. During and after laser irradiation, temperature increases in the irradiated areas were measured by thermography. The samples were then observed by stereoscopy and scanning electron microscopy to determine morphological changes and by energy dispersive x-ray spectroscopy to evaluate atomic alterations.

RESULTS

Regular holes or grooves having sharp edges and smooth walls were produced, but no melting or carbonization was observed. The maximum temperature increase was an average 12.6 degrees C for 30-second irradiation. The continuous time of a temperature increase of more than 10 degrees C was consistently less than 10 seconds. An atomic analytical examination revealed that the calcium:phosphorus ratio was not significantly changed between the lased and unlased areas (P>0.0 1).

CONCLUSION

These results showed that the Er,Cr:YSGG laser cuts canine mandibular bone effectively without burning, melting, or altering the calcium:phosphorus ratio of the irradiated bone.

Effects of erbium, chromium:YSGG laser irradiation on root surface: morphological and atomic analytical studies

OBJECTIVE

The purpose of this study was to investigate the morphological and atomic changes on the root surface by stereoscopy, field emission-scanning electron microscopy (FE-SEM), and energy dispersive X-ray spectroscopy (SEM-EDX) after erbium, chromium:yttrium, scandium, gallium, garnet (Er,Cr:YSGG) laser irradiation in vitro.

SUMMARY BACKGROUND DATA

There have been few reports on morphological and atomic analytical study on root surface by Er,Cr:YSGG laser irradiation.

METHODS

Eighteen extracted human premolar and molar teeth were irradiated on root surfaces at a vertical position with water-air spray by an Er,Cr:YSGG laser at the parameter of 5.0 W and 20 Hz for 5 sec while moving. The samples were then morphologically observed by stereoscopy and FE-SEM and examined atomic-analytically by SEM-EDX.

RESULTS

Craters having rough but clean surfaces and no melting or carbonization were observed in the samples. An atomic analytical examination showed that the calcium ratio to phosphorus showed no significant changes between the control and irradiated areas (p > 0.01).

CONCLUSIONS

These results showed that the Er,Cr:YSGG laser has a good cutting effect on root surface and causes no burning or melting after laser irradiation.