An in vitro study to assess facial and ocular deposition from Respimat Soft Mist inhaler

Effect of Nasal Inhalation on Drug Particle Deposition and Size Distribution in the Upper Airway: With Soft Mist Inhalers

Delivery of drugs to the lungs is commonly achieved using nasal and/or oral breathing-assisted techniques. The route of inhalation can substantially change the fate of inhaled droplets. The Respimat® Soft Mist™ Inhaler (SMI) is a commercially available efficient inhaler with 40-60% effectiveness. In the present study, we used computational fluid dynamics (CFD) with a custom setup to investigate the effect of a combined oral/nasal inhalation route on the SMI's regional droplet deposition, size distribution, and flow field. Our setup used a modified induction port (MIP) to mimic nasal inhalation inside the human respiratory tract. Six different oral/nasal flow rate ratios inside the MIP were applied (total flow rate of 30 l/min). An overall good agreement was achieved between simulation outcomes and in vitro results. Our results confirmed that the combined inhalation route affects the flow field, altering the MIP's droplet deposition and size distribution. The lowest depositional loss, mainly in the mouth area, was observed at oral/nasal flow rate ratios of O/N = 1 and O/N = 2 with 3% and 7.7% values, respectively. Droplets with a 2-5 µm diameter range showed the highest droplet mass inside the MIP at all combined flow rates. We observed less intense vortexes followed by a lower level of turbulent kinetic energy at the oral/nasal ratio of 1. Increasing the relative humidity (RH) at oral/nasal flow rate ratios of 0.07, 1, and 14 led to an increase in droplet deposition at the outlet of the MIP.

Pulmonary Toxicity of Benzalkonium Chloride

The available toxicity data of benzalkonium chloride (BKC) clearly shows that it is toxic; however, the weight of evidence favors the view that at doses encountered in nasally and orally inhaled pharmaceutical preparations it is well tolerated. The adverse toxicological data predominantly come from in vitro and animal studies in which doses and exposure periods employed were excessive in relation to the clinical doses and their posology and, therefore, not directly applicable to the clinic. The conflict between the in vitro and animal data and the clinical experience can be reconciled by understanding some of the physicochemical properties of BKC, the nasal and respiratory tract microenvironments, the doses used, and the posology.

The function and performance of aqueous aerosol devices for inhalation therapy

OBJECTIVES

In this review paper, we explore the interaction between the functioning mechanism of different nebulizers and the physicochemical properties of the formulations for several types of devices, namely jet, ultrasonic and vibrating-mesh nebulizers; colliding and extruded jets; electrohydrodynamic mechanism; surface acoustic wave microfluidic atomization; and capillary aerosol generation.

KEY FINDINGS

Nebulization is the transformation of bulk liquids into droplets. For inhalation therapy, nebulizers are widely used to aerosolize aqueous systems, such as solutions and suspensions. The interaction between the functioning mechanism of different nebulizers and the physicochemical properties of the formulations plays a significant role in the performance of aerosol generation appropriate for pulmonary delivery. Certain types of nebulizers have consistently presented temperature increase during the nebulization event. Therefore, careful consideration should be given when evaluating thermo-labile drugs, such as protein therapeutics. We also present the general approaches for characterization of nebulizer formulations.

SUMMARY

In conclusion, the interplay between the dosage form (i.e. aqueous systems) and the specific type of device for aerosol generation determines the effectiveness of drug delivery in nebulization therapies, thus requiring extensive understanding and characterization.

Tiotropium Respimat(®) Soft Mist™ inhaler: a review of its use in chronic obstructive pulmonary disease

The long-acting anticholinergic agent tiotropium bromide (Spiriva(®)) is available as a solution for inhalation via Respimat(®) Soft Mist™ Inhaler in the EU and various other countries for the treatment of chronic obstructive pulmonary disease (COPD). With the Respimat(®) Soft Mist™ Inhaler there is improved lung deposition of drug (allowing a reduced dosage compared with tiotropium HandiHaler(®)), the delivered drug dose is independent of inspiratory effort and the prolonged duration of the aerosol cloud should make the co-ordination of actuation and inhalation easier. In patients with COPD, tiotropium Respimat(®) improved lung function, COPD exacerbations, health-related quality of life and dyspnoea and was at least as effective as tiotropium HandiHaler(®). Tiotropium Respimat(®) was generally well tolerated in patients with COPD, with anticholinergic adverse events among the most commonly reported adverse events. In the TIOSPIR trial, tiotropium Respimat(®) was noninferior to tiotropium HandiHaler(®) in terms of all-cause mortality, and the risk of cardiovascular mortality or major adverse cardiovascular events did not significantly differ between the two treatment groups. In conclusion, tiotropium Respimat(®) Soft Mist™ Inhaler is a useful option for the treatment of patients with COPD.

Considerations for Designing In Vitro Bioequivalence (IVBE) Studies for Pressurized Metered Dose Inhalers (pMDIs) with Spacer or Valved Holding Chamber (S/VHC) Add-on Devices

BACKGROUND

The choice of analytical test methods and associated statistical considerations are considered for the laboratory testing of pressurized metered dose inhaler-spacer/valved holding chamber (pMDI-S/VHC) combinations for in vitro bioequivalence (IVBE).

METHODS

Four scenarios are presented for comparing TEST ("second entry" or "generic") versus REF ("innovator"): (1) innovator and second entry product pMDI alone without any S/VHC (baseline comparison); (2) innovator and second entry pMDI product with the same S/VHC; (3) innovator pMDI product with existing S/VHC and second entry product with a different S/VHC; and (4) introduction of a second, different S/VHC to be used with a given innovator pMDI product. The following aspects should be reviewed in the preparatory stage of designing experiments to establish IVBE: (a) the inclusion of delayed inhalation; (b) the utilization of age-appropriate flow rates; and (c) the use of anatomically appropriate face models for evaluation of devices with a facemask. Statistical considerations that fit in with such experimental methods include: selection of pMDI batches and S/VHC lots; choice of sample size and acceptance criteria; bracketing or worst case approaches; and balanced/paired designs. A stepwise approach for selection of impactor stage groupings is presented, and an approach to determine realistic acceptance criteria based on REF product characteristics is suggested.

RESULTS

An example of an efficient statistical design of experiment is provided for each scenario, together with alternate approaches for calculation of confidence intervals for the mean TEST/REF relationship. It is important to appreciate that the optimal design depends on balancing numerous considerations and will thus likely differ from case to case; hence, the designs presented here should be seen as illustrations rather than the only option available. More effective approaches may be found that suit a particular case at hand.

CONCLUSIONS

The information provided will assist in developing correlations in support of IVBE for these add-on devices.

Equivalence considerations for orally inhaled products for local action-ISAM/IPAC-RS European Workshop report

The purpose of this article is to document the discussions at the 2010 European Workshop on Equivalence Determinations for Orally Inhaled Drugs for Local Action, cohosted by the International Society for Aerosols in Medicine (ISAM) and the International Pharmaceutical Consortium on Regulation and Science (IPAC-RS). The article summarizes current regulatory approaches in Europe, the United States, and Canada, and presents points of consensus as well as ongoing debate in the four major areas: in vitro testing, pharmacokinetic and pharmacodynamic studies, and device similarity. Specific issues in need of further research and discussion are also identified.

Current therapies and technological advances in aqueous aerosol drug delivery

Recent advances in aerosolization technology have led to renewed interest in pulmonary delivery of a variety of drugs. Pressurized metered dose inhalers (pMDIs) and dry powder inhalers (DPIs) have experienced success in recent years; however, many limitations are presented by formulation difficulties, inefficient delivery, and complex device designs. Simplification of the formulation process as well as adaptability of new devices has led many in the pharmaceutical industry to reconsider aerosolization in an aqueous carrier. In the acute care setting, breath-enhanced air-jet nebulizers are controlling and minimizing the amount of wasted medication, while producing a high percentage of respirable droplets. Vibrating mesh nebulizers offer advantages in higher respirable fractions (RFs) and slower velocity aerosols when compared with air-jet nebulizers. Vibrating mesh nebulizers incorporating formulation and patient adaptive components provide improvements to continuous nebulization technology by generating aerosol only when it is most likely to reach the deep lung. Novel innovations in generation of liquid aerosols are now being adapted for propellant-free pulmonary drug delivery to achieve unprecedented control over dose delivered and are leading the way for the adaptation of systemic drugs for delivery via the pulmonary route. Devices designed for the metered dose delivery of insulin, morphine, sildenafil, triptans, and various peptides are all currently under investigation for pulmonary delivery to treat nonrespiratory diseases. Although these devices are currently still in clinical testing (with the exception of the Respimat), metered dose liquid inhalers (MDLIs) have already shown superior outcomes to current pulmonary and systemic delivery methods.