Effect of Er:YAG Laser Etching on the Shear Bond Strength and Microleakage of Self-Glazed Zirconia Ceramics

The possibility of clinical bonding between metal/ceramic brackets to zirconia: in vitro study

Objective: The present study aimed to assess the bond strength and durability of six bonding agents concerning their application to metal or ceramic brackets and zirconia. Materials and Methods: Six resin cement bonding agents (XT, XTS, RSBU, RGBU, SBPM, and GMP) were chosen for this investigation. Specimens were either stored in distilled water at 37°C for 24 h or subjected to 5,000 thermocycles before conducting a Shear Bond Strength (SBS) test. Statistical analysis of the SBS data was performed using three-way ANOVA and Games-Howell tests (α = 0.05). The Adhesive Remnant Index was examined, and the debonding surface details on brackets and zirconia were observed. Results: For metal brackets, all groups demonstrated clinically acceptable bond strength, irrespective of storage conditions, except for the XT group. Regarding ceramic brackets, all groups displayed acceptable bond strength after 24 h of water storage. However, following thermocycling, a significant decrease in SBS was noted across all groups (p < 0.05), with SBPM exhibiting a higher bond strength. Three-way ANOVA analysis indicated that SBS values were notably influenced by each factor, and an interaction among the three independent variables was observed (p = 0.000). Conclusion: The reliable bond strength between ceramic brackets and zirconia was significantly lower after thermocycling compared to that of metal brackets and zirconia. SBPM exhibited consistent and robust bond strength between ceramic/metal brackets and zirconia across various storage conditions. Furthermore, the HEMA-free adhesive demonstrated a potentially more consistent bonding performance compared to the HEMA-containing adhesive employed in this study.

Effect of silica coating and laser treatment on the flexural strength, surface characteristics, and bond strength of a dental zirconia

This study investigated the effect of irradiation with an erbium-doped yttrium aluminium garnet (Er:YAG) laser and coating with silica on the surface characteristics, bond strength, and flexural strength of dental zirconia. Three hundred and forty-three standard zirconia specimens were created, and 49 were assigned to each of seven surface treatment groups: (i) no treatment; Er:YAG laser (80 mJ/2 Hz) with pulse widths of 50 μs (ii), 100 μs (iii), 300 μs (iv), or 600 μs (v); or tribochemical silica coating at the partially sintered stage (vi) or after sintering was complete (vii). All specimens were sintered after the surface treatments, except for the group in which specimens were sintered before treatment. The study outcomes were roughness, surface loss, microshear bond strength (μSBS), and biaxial flexural strength (BFS). Mean roughness and surface loss values were significantly higher in specimens from irradiated groups than in those from silica-coated groups. Regarding μSBS, after aging, specimens from all experimental groups presented very low and similar μSBS values, irrespective of the surface treatment. Silica coating after sintering yielded the highest BFS (1149.5 ± 167.6 MPa), while coating partially sintered specimens with silica resulted a BFS (826.9 ± 60.9 MPa) similar to that of the untreated control group (794.9 ± 101.7 MPa). Laser treatments, irrespective of pulse width used, significantly decreased the BFS. In the group treated with laser at 300 μs pulse width, specimens exhibited the lowest BFS value (514.1 ± 71.5 MPa). Adhesion to zirconia was not stable after aging, regardless of the surface treatment implemented.

Effects of Dentin Ablation by a Q-Switching Er:YSGG Laser with a High Pulse Repetition Rate

Objective: The aim of the study was to evaluate the characteristics of dentin ablation with a high pulse repetition rate Q-switching 2.79 μm laser. Materials and methods: Dentin was ablated using a homemade Q-switching Er:YSGG laser with a high pulse repetition rate. Er:YSGG radiation was applied with a pulse energy of 1 or 10 mJ for 100 or 3 Hz pulse repetition rate, respectively. A scanning electron microscope (SEM) was used to observe the microstructures of dentin samples after ablation. Teeth were irradiated in vitro with a 100 Hz pulse repetition rate under two different modes: free running and Q-switching. A thermocouple was applied to measure the temperature in the pulp cavity during ablation. Results: A 100 or 3 Hz Q-switching laser was used to irradiate dentin for 30 and 100 sec, respectively. There was no significant difference in ablation mass loss between the two conditions. The SEM photographs showed more dentinal tubules and no damage in the ablation area when using the 100 Hz Q-switching laser. The temperature of the pulp cavity was maintained below 41°C when using a Q-switching laser. Conclusions: The Q-switching Er:YSGG laser with a high pulse repetition rate exhibited greater ablation efficiency and better morphology than the low pulse repetition rate Q-switching laser. The experimental results also demonstrate the significant advantage of the Q-switching laser over free-running lasers for protecting dental pulp tissue. The Q-switching Er:YSGG laser with a high pulse repetition rate is expected to become an efficient new dental tool.