Advanced bone formation in grooves in vitro is not restricted to calcified biological materials

ROMP-Derived cyclooctene-based monolithic polymeric materials reinforced with inorganic nanoparticles for applications in tissue engineering

Porous monolithic inorganic/polymeric hybrid materials have been prepared via ring-opening metathesis copolymerization starting from a highly polar monomer, i.e., cis-5-cyclooctene-trans-1,2-diol and a 7-oxanorborn-2-ene-derived cross-linker in the presence of porogenic solvents and two types of inorganic nanoparticles (i.e., CaCO₃ and calcium hydroxyapatite, respectively) using the third-generation Grubbs initiator RuCl₂(Py)₂(IMesH₂)(CHPh). The physico-chemical properties of the monolithic materials, such as pore size distribution and microhardness were studied with regard to the nanoparticle type and content. Moreover, the reinforced monoliths were tested for the possible use as scaffold materials in tissue engineering, by carrying out cell cultivation experiments with human adipose tissue-derived stromal cells.

Stereo imaging and cytocompatibility of a model dental implant surface formed by direct laser fabrication

Direct laser fabrication (DLF) allows solids with complex geometry to be produced by sintering metal powder particles in a focused laser beam. In this study, 10 Ti6Al4V alloy model dental root implants were obtained by DLF, and surface characterization was carried out using stereo scanning electron microscopy to produce 3D reconstructions. The surfaces were extremely irregular, with approximately 100 microm deep, narrow intercommunicating crevices, shallow depressions and deep, rounded pits of widely variable shape and size, showing ample scope for interlocking with the host bone. Roughness parameters were as follows: R(t), 360.8 microm; R(z), 358.4 microm; R(a), 67.4 microm; and R(q), 78.0 microm. Disc specimens produced by DLF with an identically prepared surface were used for biocompatibility studies with rat calvarial osteoblasts: After 9 days, cells had attached and spread on the DLF surface, spanning across the crevices, and voids. Cell density was similar to that on a commercial rough microtextured surface but lower than on commercial smooth machined and smooth-textured grit-blasted, acid-etched surfaces. Human fibrin clot extension on the DLF surface was slightly improved by inorganic acid etching to increase the microroughness. With further refinements, DLF could be an economical means of manufacturing implants from titanium alloys.

Nanoscale modifications of PET polymer surfaces via oxygen-plasma discharge yield minimal changes in attachment and growth of mammalian epithelial and mesenchymal cells in vitro

Surface topography is believed to be a factor affecting cellular morphology, proliferation, and differentiation. The effect of surface roughness in the micron to supramicron range has been investigated previously. In the current study, the influence of nanoscale surface roughness was examined in terms of its effects on morphology, cytoskeleton expression, proliferation, differentiation, and apoptosis of three model cell types. Polyethylene terephthalate (PET) disks were etched using oxygen plasma to produce uniform and decidedly nanoscale levels of surface roughness. Three distinct types of cell lines-mouse 3T3-L1 preadipocytes, human JEG-3 choriocarcinoma cells, and human MCF-7 breast adenocarcinoma cells-were cultured on the plasma-treated disks. Untreated PET disks were used as a control. Cytoskeletal proteins (F-actin and cytokeratin) exhibited similar patterns of expression. Cell morphology also was similar on both surfaces. Cell growth kinetics for the three types of cells and hormone secretion from the JEG-3 cells were not significantly different from that of the controls (p > 0.05). However, the differentiation of preadipocyte 3T3-L1 cells into lipid-laden fat cells was modestly affected by nanoscale surface topography. In addition, 15-deoxy-Delta(12,14)-prostaglandin J(2) (15dPGJ(2))-induced apoptosis of the JEG-3 and MCF-7 cells revealed differences between the two surfaces. Plasma-treated surfaces showed more differentiated and apoptotic cells, respectively, compared to the controls. These results indicate that nanoscale roughness contributes in only moderate ways to cellular adhesion, proliferation, and differentiation in the cell lines tested.