Near Field Flow Characteristics of the Bjork-Shiley Monostrut Valve in a Modified Single Shot Valve Chamber

Role of vortices in cavitation formation in the flow at the closure of a bileaflet mitral mechanical heart valve

Bubble cavitation occurs in the flow field when local pressure drops below vapor pressure. One hypothesis states that low-pressure regions in vortices created by instantaneous valve closure and occluder rebound promote bubble formation. To quantitatively analyze the role of vortices in cavitation, we applied particle image velocimetry (PIV) to reduce the instantaneous fields into plane flow that contains information about vortex core radius, maximum tangential velocity, circulation strength, and pressure drop. Assuming symmetrical flow along the center of the St. Jude Medical 25-mm valve, flow fields downstream of the closing valve were measured using PIV in the mitral position of a circulatory mock loop. Flow measurements were made during successive time phases immediately following the impact of the occluder with the housing (O/H impact) at valve closing. The velocity profile near the vortex core clearly shows a typical Rankine vortex. The vortex strength reaches maximum immediately after closure and rapidly decreases at about 10 ms, indicating viscous dissipation; vortex strength also intensifies with rising pulse rate. The maximum pressure drop at the vortex center is approximately 20 mmHg, an insignificant drop relative to atmospheric vapor pressures, which implies vortices play a minor role in cavitation formation.

A detailed fluid mechanics study of tilting disk mechanical heart valve closure and the implications to blood damage

Hemolysis and thrombosis are among the most detrimental effects associated with mechanical heart valves. The strength and structure of the flows generated by the closure of mechanical heart valves can be correlated with the extent of blood damage. In this in vitro study, a tilting disk mechanical heart valve has been modified to measure the flow created within the valve housing during the closing phase. This is the first study to focus on the region just upstream of the mitral valve occluder during this part of the cardiac cycle, where cavitation is known to occur and blood damage is most severe. Closure of the tilting disk valve was studied in a "single shot" chamber driven by a pneumatic pump. Laser Doppler velocimetry was used to measure all three velocity components over a 30 ms period encompassing the initial valve impact and rebound. An acrylic window placed in the housing enabled us to make flow measurements as close as 200 microm away from the closed occluder. Velocity profiles reveal the development of an atrial vortex on the major orifice side of the valve shed off the tip of the leaflet. The vortex strength makes this region susceptible to cavitation. Mean and maximum axial velocities as high as 7 ms and 20 ms were recorded, respectively. At closure, peak wall shear rates of 80,000 s(-1) were calculated close to the valve tip. The region of the flow examined here has been identified as a likely location of hemolysis and thrombosis in tilting disk valves. The results of this first comprehensive study measuring the flow within the housing of a tilting disk valve may be helpful in minimizing the extent of blood damage through the combined efforts of experimental and computational fluid dynamics to improve mechanical heart valve designs.

Wavelet transforms in the analysis of mechanical heart valve cavitation

Cavitation is known to cause blood element damage and may introduce gaseous emboli into the cerebral circulation, increasing the patient's risk of stroke. Discovering methods to reduce the intensity of cavitation induced by mechanical heart valves (MHVs) has long been an area of interest. A novel approach for analyzing MHV cavitation is presented. A wavelet denoising method is explored because currently used analytical techniques fail to suitably unmask the cavitation signal from other valve closing sounds and noise detected with a hydrophone. Wavelet functions are used to denoise the cavitation signal during MHV closure and rebound. The wavelet technique is applied to the signal produced by closure of a 29-mm Medtronic-Hall MHV in degassed water with a gas content of 5 ppm. Valve closing dynamics are investigated under loading conditions of 500, 2500, and 4500 mm Hg/s. The results display a marked improvement in the quantity and quality of information that can be extracted from acoustic cavitation signals using the wavelet technique compared to conventional analytical techniques. Time and frequency data indicate the likelihood and characteristics of cavitation formation under specified conditions. Using this wavelet technique we observe an improved signal-to-noise ratio, an enhanced time-dependent aspect, and the potential to minimize valve closing sounds, which disguise individual cavitation events. The overall goal of this work is to eventually link specific valves with characteristic waveforms or distinct types of cavitation, thus promoting improved valve designs.