Arterial geometry, flow pattern, wall shear and mass transport: potential physiological significance

A 3D scaling law for supravalvular aortic stenosis suited for stethoscopic auscultations

In this study a frequency scaling law for 3D anatomically representative supravalvular aortic stenosis (SVAS) cases is proposed. The law is uncovered for stethoscopy's preferred auscultation range (70-120 Hz). LES simulations are performed on the CFD solver Fluent, leveraging Simulia's Living Heart Human Model (LHHM), modified to feature hourglass stenoses that range between 30 to 80 percent (mild to severe) in addition to the descending aorta. For physiological hemodynamic boundary conditions the Windkessel model is implemented via a UDF subroutine. The flow-generated acoustic signal is then extracted using the FW-H model and analyzed using FFT. A preferred receiver location that matches clinical practice is confirmed (right intercostal space) and a correlation between the degree of stenosis and a corresponding acoustic frequency is obtained. Five clinical auscultation signals are tested against the scaling law, with the findings interpreted in relation to the NHS classification of stenosis and to the assessments of experienced cardiologists. The scaling law is thus shown to succeed as a potential quantitative decision-support tool for clinicians, enabling them to reliably interpret stethoscopic auscultations for all degrees of stenosis, which is especially useful for moderate degrees of SVAS. Computational investigation of more complex stenotic cases would enhance the clinical relevance of this proposed scaling law, and will be explored in future research.

Vascular Cast to Program Antistenotic Hemodynamics and Remodeling of Vein Graft

The structural stability of medical devices is established by managing stress distribution in response to organ movement. Veins abruptly dilate upon arterial grafting due to the mismatched tissue property, resulting in flow disturbances and consequently stenosis. Vascular cast is designed to wrap the vein-artery grafts, thereby adjusting the diameter and property mismatches by relying on the elastic fixity. Here, a small bridge connection in the cast structure serves as an essential element to prevent stress concentrations due to the improved elastic fixity. Consequently, the vein dilation is efficiently suppressed, healthy (laminar and helical) flow is induced effectively, and the heathy functions of vein grafting are promoted, as indicated by the flow directional alignment of endothelial cells with arterialization, muscle expansion, and improved contractility. Finally, collaborative effects of the bridge drastically suppress stenosis with patency improvement. As a key technical point, the advantages of the bridge addition are validated via the computational modeling of fluid-structure interaction, followed by a customized ex vivo set-up and analyses. The calculated effects are verified using a series of cell, rat, and canine models towards translation. The bridge acted like "Little Dutch boy" who saved the big mass using one finger by supporting the cast function.

The loss of helical flow in the thoracic aorta might be an identifying marker for the risk of acute type B aortic dissection

BACKGROUND AND OBJECTIVE

The occurrence of acute type B aortic dissection (TBAD) remained unclear. This study aimed to investigate the association between flow features and hemodynamic parameters in aortas that demonstrated the risk of TBAD occurrence.

METHODS

The geometries of 15 hyperacute TBAD and 12 control patients (with healthy aorta) were reconstructed from computed tomography angiography images. Pre-TBAD models were then obtained by eliminating the dissection flaps. Flow features and hemodynamic parameters, including wall shear stress-related parameters and helicities, were compared between pre-TBAD and control models using computational fluid dynamics.

RESULTS

There were no significant differences in baseline characteristics and anatomical parameters between the two groups. Significant contralateral helical blood flow was present in the healthy thoracic aorta, while almost no helical flow was observed in the pre-TBAD group. In addition, the mean normal transverse wall shear stress (NtransWSS) was significantly higher in the pre-TBAD group (aortic arch 0.49±0.09 vs. 0.40±0.05, P = 0.04; descending aorta: 0.46±0.05 vs. 0.33±0.02, P<0.01). Moreover, a significantly negative correlation was found between helicity and NtransWSS in the descending aorta. Moreover, the location of primary tears in 12 pre-TABD subjects matched well with regions of high NtransWSS.

CONCLUSIONS

Loss of helical flow in the aortic arch and descending aorta may be a major flow feature in patients with underlying TBAD, resulting in increased flow disturbance and wall lesions.

Components of Oranta-AO software expert system for innovative application of blood pressure monitors

The authors developed and substantiated the original methods of arterial oscillography, which were implemented in the developed Oranta-AO information system. The methods of application to the arterial oscillogram registered at measurement of arterial pressure gives the possibility to carry out the supplementary systematic assessment of health, functional state of cardiovascular system, its reserve possibilities etc. The authors also developed an Expert System (based on machine-learning methods) for the differential diagnosis of risks of heart, lung, mental illness and prognosis of some blood parameters. Oranta-AO software system was created based on research results due to methods and algorithms that were innovate. For the mathematical modeling of arterial oscillograms used cyclic random processes. Methods of arterial oscillograms processing based on its model in the form of a cyclic random process was developed. The method of evaluation of the rhythm function of arterial oscillograms and statistical methods for estimating the probabilistic characteristics of arterial oscillograms were developed. To solve the clustering problem, the Python k-means and k-means++ algorithm were used. Oranta-AO information system consists of three interrelated parts: mobile application, computing kernel and web system. Computing kernel and web system are deployed on AWS servers and have been tested already. The developed environment aims to be integrated into every new model of electronic meters in the world. Certification (EN 62304:2014, ISO 13485: 2018) in Ukraine is completed, PCT priority is completed. The next step will be to establish cooperation with manufacturers of electronic pressure monitors, patenting and certification in world.

Heterogeneous Maturation of Arterio-Venous Fistulas and Loop-Shaped Venous Interposition Grafts: A Histological and 3D Flow Simulation Comparison

Vascular graft maturation is associated with blood flow characteristics, such as velocity, pressure, vorticity, and wall shear stress (WSS). Many studies examined these factors separately. We aimed to examine the remodeling of arterio-venous fistulas (AVFs) and loop-shaped venous interposition grafts, together with 3D flow simulation. Thirty male Wistar rats were randomly and equally divided into sham-operated, AVF, and loop-shaped venous graft (Loop) groups, using the femoral and superficial inferior epigastric vessels for anastomoses. Five weeks after surgery, the vessels were removed for histological evaluation, or plastic castings were made and scanned for 3D flow simulation. Remodeling of AVF and looped grafts was complete in 5 weeks. Histology showed heterogeneous morphology depending on the distribution of intraluminal pressure and WSS. In the Loop group, an asymmetrical WSS distribution coincided with the intima hyperplasia spots. The tunica media was enlarged only when both pressure and WSS were high. The 3D flow simulation correlated with the histological findings, identifying “hotspots” for intimal hyperplasia formation, suggesting a predictive value. These observations can be useful for microvascular research and for quality control in microsurgical training.

Comparative study of the effects of cigarette smoke versus next generation tobacco and nicotine product extracts on endothelial function

Tobacco smoking and hemodynamic forces are key stimuli for the development of endothelial dysfunction. As an alternative to smoking, next generation tobacco and nicotine products (NGP) are now widely used. However, little is known about their potential pro-inflammatory and atherogenic effects on the endothelium. In this study, we analyzed key parameters of endothelial function after exposure to aqueous smoke extracts (AqE) of a heated tobacco product (HTP), an electronic cigarette (e-cig), a conventional cigarette (3R4F) and pure nicotine. All experiments were performed under atheroprotective high laminar or atherogenic low flow with primary human endothelial cells. Treatment with 3R4F, but not alternative smoking products, reduced endothelial cell viability and wound healing capability via the PI3K/AKT/eNOS(NOS3) pathway. Laminar flow delayed detrimental effects on cell viability by 3R4F treatment. 3R4F stimulation led to activation of NRF2 antioxidant defense system at nicotine concentrations ≥0.56 μg/ml and increased expression of its target genes HMOX1 and NQO1. Treatment with HTP revealed an induction of HMOX1 and NQO1 at dosages with ≥1.68 μg/ml nicotine, whereas e-cig and nicotine exposure had no impact. Analyses of pro-inflammatory genes revealed an increased ICAM1 expression under 3R4F treatment. 3R4F reduced VCAM1 expression in a dose-dependent manner; HTP treatment had similar but milder effects; e-cig and nicotine treatment had no impact. SELE expression was induced by 3R4F under static conditions. High laminar flow prevented this upregulation. Stimulation with laminar flow led to downregulation of CCL2 (MCP-1). From this downregulated level, only 3R4F increased CCL2 expression at higher concentrations. Finally, under static conditions, all components increased adhesion of monocytes to endothelial cells. Interestingly, only stimulation with 3R4F revealed increased monocyte adhesion under atherosclerosis-prone low flow. In conclusion, all product categories activated anti-oxidative or pro-inflammatory patterns. NGP responses were typically lower than in 3R4F exposed cells. Also, 3R4F stimulation led to an impaired endothelial wound healing and induced a pro-inflammatory phenotype compared to NGP treatment.

Organotypic endothelial adhesion molecules are key for Trypanosoma brucei tropism and virulence

Trypanosoma brucei is responsible for lethal diseases in humans and cattle in Sub-Saharan Africa. These extracellular parasites extravasate from the blood circulation into several tissues. The importance of the vasculature in tissue tropism is poorly understood. Using intravital imaging and bioluminescence, we observe that gonadal white adipose tissue and pancreas are the two main parasite reservoirs. We show that reservoir establishment happens before vascular permeability is compromised, suggesting that extravasation is an active mechanism. Blocking endothelial surface adhesion molecules (E-selectin, P-selectins, or ICAM2) significantly reduces extravascular parasite density in all organs and delays host lethality. Remarkably, blocking CD36 has a specific effect on adipose tissue tropism that is sufficient to delay lethality, suggesting that establishment of the adipose tissue reservoir is necessary for parasite virulence. This work demonstrates the importance of the vasculature in a T. brucei infection and identifies organ-specific adhesion molecules as key players for tissue tropism.

•

Our study investigates the blood vasculature for T. brucei reservoir establishment

•

We show the pancreas is a large extravascular reservoir

•

We establish that T. brucei tropism is linked to organotypic adhesion molecules

•

Interfering with adhesion molecules impacts parasite virulence and host survival

Micro-Rheological Changes of Red Blood Cells in the Presence of an Arterio-Venous Fistula or a Loop-Shaped Venous Graft in the Rat

Introduction: In case of kidney failure, hemodialysis is the primary kidney replacement technique. Several vascular access methods used for the therapy, one of which is the arterio-venous fistula (AVF). In the AVF, the blood flow is altered, which can elevate the mechanical stress on the red blood cells (RBCs). This can affect the RBC hemorheological properties, and it can further cause systemic changes. To lower the turbulence and shear stress, we performed a loop-shaped arterio-arterial venous interposition graft (loop-shaped graft) to compare its effect to the conventional AVF. Materials and Methods: Thirty male Wistar were used (permission registration Nr.: 25/2016/UDCAW). The animals were randomly divided into sham-operated, AVF, and loop groups (n = 10/each). The superficial inferior epigastric vein (SIEV) was used to create the AVF and the loop-shaped graft. Blood samples were taken before/after the surgery and at the 1st, 3rd, and 5th postoperative weeks. We measured hemorhelogical, hematological, and blood gas parameters. The microcirculation of the hind limbs was also monitored using Laser Doppler fluxmetry. Results: Hematocrit, RBC count, and hemoglobin decreased by the 1st postoperative week. The erythrocyte aggregation values significantly increased in the fistula group by the 5th week (6.43 ± 2.31 vs. 13.60; p < 0.0001; vs. before operation). At the postoperative 1st week in the loop group, the values showed a significant decrease in RBC deformability. During the maturation period, dominantly at the 5th week, all values were normalized. The operated hind limb's skin microcirculation significantly increased in the sham and loop group by the 1st week (39 ± 10.57 vs. 73.93 ± 1.97 BFU, p < 0.01). This increase wasn't observed in the fistula group probably due to a steal-effect. Conclusion: Unlike in the loop group, in the presence of the fistula, several rheological parameters have changed. The loop-shaped graft had only minimal impact on micro-rheological parameters.

Numerical considerations for advection-diffusion problems in cardiovascular hemodynamics

Numerical simulations of cardiovascular mass transport pose significant challenges due to the wide range of Péclet numbers and backflow at Neumann boundaries. In this paper we present and discuss several numerical tools to address these challenges in the context of a stabilized finite element computational framework. To overcome numerical instabilities when backflow occurs at Neumann boundaries, we propose an approach based on the prescription of the total flux. In addition, we introduce a "consistent flux" outflow boundary condition and demonstrate its superior performance over the traditional zero diffusive flux boundary condition. Lastly, we discuss discontinuity capturing (DC) stabilization techniques to address the well-known oscillatory behavior of the solution near the concentration front in advection-dominated flows. We present numerical examples in both idealized and patient-specific geometries to demonstrate the efficacy of the proposed procedures. The three contributions discussed in this paper successfully address commonly found challenges when simulating mass transport processes in cardiovascular flows.

Pulmonary artery hemodynamic assessment of blood flow characteristics in repaired tetralogy of Fallot patients versus healthy child volunteers

Background

This study aimed to assess the severity of helix and vortex flow in pulmonary artery hemodynamic using 4-dimensional flow cardiac magnetic resonance (4D flow CMR) in patients with repaired tetralogy of Fallot (rTOF) and healthy child volunteers and to explore the relationship between pulmonary hemodynamic changes and right heart function.

Methods

CMR studies were performed in 25 rTOF patients (15 M/10 F; 8.44±4.52 years) and 10 normal child volunteers (7 M/3 F; 8.2±1.22 years) on 3.0T MR scanners. Cardiac function was calculated in the patient and control groups. Systolic diameter, peak velocity, net flow, and regurgitation was quantified in the main pulmonary artery (MPA) plane, left pulmonary artery (LPA) plane, and right pulmonary artery (RPA) plane. The relationship between the hemodynamic parameters and quantitative flow indices and right ventricular (RV) function were analyzed through simple linear regression analysis using Pearson R-values. We analyzed differences in flow patterns between the 2 groups for the same slice. According to the severity of the helix and vortex flow in the 4D flow CMR, we categorized rTOF patients into the following groups: group 1, severe flow grading; group 2, mild flow grading; group 3, no flow grading; the control cases with no flow grade were included in group 4. We compared RV cardiac function, wall shear stress (WSS), and viscous energy loss (EL) between group 1+2 and group 3+4 using unpaired t-test analysis for normally distributed data and the Mann-Whitney test for non-normally distributed continuous variables.

Results

RV end-diastolic volume index (EDV_i) (127.8±36.13 vs. 83.11±6.18, respectively; P<0.001), RV end-systolic volume index (ESV_i) (65.14±27.02 vs. 36.13±5.95, respectively; P<0.001), and ejection fraction (EF) (49.97±6.39 vs. 56.71±4.56, respectively; P=0.006,) were significantly different between the groups. The rTOF diameters of the MPA and RPA were significantly larger than those of the control group (19.74±4.01 vs. 14.97±2.37 for MPA, P=0.001; 12.04±3.28 vs. 8.99±1.23 for RPA, P=0.004, respectively). There were correlations between peak WSS and pulmonary regurgitation (PR) in the MPA (R=0.48, P=0.014), correlations between peak systolic EL and RVEDV (R=0.51, P=0.008), and between peak systolic EL and RVESV (R=0.51, P=0.009). The peak systole and diastole WSS of group 1+2 were significantly different compared to group 3+4 in the MPA (P<0.05). The peak systole and diastole EL of group 1+2 was significantly different from group 3+4 in the MPA (P<0.05). The peak systole EL of group 1+2 was significantly different from group 3+4 in the RPA (P<0.01).

Conclusions

Increased peak WSS and EL were associated with pulmonary hemodynamic changes in the MPA and RPA. There might be an earlier marker of evolving hemodynamic inefficiency than that in traditional parameters. The better understanding of pulmonary artery hemodynamic assessment in rTOF may lead to a greater insight into pulmonary artery (PA)-RV interactions and how they ultimately impact RV function.

The role of oxygen transport in atherosclerosis and vascular disease

Atherosclerosis and vascular disease of larger arteries are often associated with hypoxia within the layers of the vascular wall. In this review, we begin with a brief overview of the molecular changes in vascular cells associated with hypoxia and then emphasize the transport mechanisms that bring oxygen to cells within the vascular wall. We focus on fluid mechanical factors that control oxygen transport from lumenal blood flow to the intima and inner media layers of the artery, and solid mechanical factors that influence oxygen transport to the adventitia and outer media via the wall's microvascular system-the vasa vasorum (VV). Many cardiovascular risk factors are associated with VV compression that reduces VV perfusion and oxygenation. Dysfunctional VV neovascularization in response to hypoxia contributes to plaque inflammation and growth. Disturbed blood flow in vascular bifurcations and curvatures leads to reduced oxygen transport from blood to the inner layers of the wall and contributes to the development of atherosclerotic plaques in these regions. Recent studies have shown that hypoxia-inducible factor-1α (HIF-1α), a critical transcription factor associated with hypoxia, is also activated in disturbed flow by a mechanism that is independent of hypoxia. A final section of the review emphasizes hypoxia in vascular stenting that is used to enlarge vessels occluded by plaques. Stenting can compress the VV leading to hypoxia and associated intimal hyperplasia. To enhance oxygen transport during stenting, new stent designs with helical centrelines have been developed to increase blood phase oxygen transport rates and reduce intimal hyperplasia. Further study of the mechanisms controlling hypoxia in the artery wall may contribute to the development of therapeutic strategies for vascular diseases.

Efficiently Generating Mixing by Combining Differing Small Amplitude Helical Geometries

Helical geometries have been used in recent years to form cardiovascular prostheses such as stents and shunts. The helical geometry has been found to induce swirling flow, promoting in-plane mixing. This is hypothesised to reduce the formation of thrombosis and neo-intimal hyperplasia, in turn improving device patency and reducing re-implantation rates. In this paper we investigate whether joining together two helical geometries, of differing helical radii, in a repeating sequence, can produce significant gains in mixing effectiveness, by embodying a ‘streamline crossing’ flow environment. Since the computational cost of calculating particle trajectories over extended domains is high, in this work we devised a procedure for efficiently exploring the large parameter space of possible geometry combinations. Velocity fields for the single geometries were first obtained using the spectral/hp element method. These were then discontinuously concatenated, in series, for the particle tracking based mixing analysis of the combined geometry. Full computations of the most promising combined geometries were then performed. Mixing efficiency was evaluated quantitatively using Poincaré sections, particle residence time data, and information entropy. Excellent agreement was found between the idealised (concatenated flow field) and the full simulations of mixing performance, revealing that a strict discontinuity between velocity fields is not required for mixing enhancement, via streamline crossing, to occur. Optimal mixing was found to occur for the combination R = 0.2 D and R = 0.5 D , producing a 70 % increase in mixing, compared with standard single helical designs. The findings of this work point to the benefits of swirl disruption and suggest concatenation as an efficient means to determine optimal configurations of repeating geometries for future designs of vascular prostheses.

Precise plan of hybrid treatment for thoracoabdominal aortic aneurysm: Hemodynamics of retrograde reconstruction visceral arteries from the iliac artery

Hybrid visceral-renal debranching procedures with endovascular repair have been proposed as a less invasive alternative to conventional thoracoabdominal aortic aneurysm or dissection (TAAA or TAAD) surgery. Up to now, there has been no information about the hemodynamic effects of retrograde visceral reconstruction (RVR) for Crawford type II/III/IV TAAA patients undergoing hybrid treatment. The aim is to provide insights in the abnormal hemodynamics of RVR from unilateral or bilateral common iliac arteries (CIAs). Idealized three-dimensional AAs with RVR from unilateral CIA or bilateral CIAs were generated and computationally simulated. The results show that RVRs from CIA lead to a dramatic decrease in flow to the visceral organs compared with a healthy AA and that the anastomosis region is most dangerous to graft occlusion and the initiation of an aneurysm. In addition, compared with a quar-furcated graft, the employment of bilateral bi-furcated grafts have better performance in terms of the wall shear stress (WSS) and flow filed but result in less flow to the celiac and mesenteric arteries. This study has revealed the potential risks after an RVR operation, and points out the advantages and disadvantages of different approaches for the visceral reconstruction, which the vascular surgeons are not fully aware of. According to our results, bilateral bi-furcated grafts are recommended to the TAAA patients when the CIAs are unique inflow sites for visceral reconstruction. A precise plan with patient specific for TAAA or TAAD will be designed for better long-term outcome.

Small diameter helical vascular scaffolds support endothelial cell survival

There is an acute clinical need for small-diameter vascular grafts as a treatment option for cardiovascular disease. Here, we used an intelligent design system to recreate the natural structure and hemodynamics of small arteries. Nano-fibrous tubular scaffolds were fabricated from blends of polyvinyl alcohol and gelatin with inner helices to allow a near physiological spiral flow profile, using the electrospinning technique. Human coronary artery endothelial cells (ECs) were seeded on the inner surface and their viability, distribution, gene expression of mechanosensitive and adhesion molecules compared to that in conventional scaffolds, under static and flow conditions. We show significant improvement in cell distribution in helical vs. conventional scaffolds (94% ± 9% vs. 82% ± 7.2%; P < 0.05) with improved responsiveness to shear stress and better ability to withhold physiological pressures. Our helical vascular scaffold provides an improved niche for EC growth and may be attractive as a potential small diameter vascular graft.

Hemodynamics and Oxygen Transport through Pararenal Aortic Aneurysm Treated with Multilayer Stent: A Numerical Study

BACKGROUND

As opposed to an endoluminal stent graft, a multilayer stent (MS) consists of a porous mesh, which allows for the possibility of treating pararenal aortic aneurysms (PRAAs) that involve a significant branch vessel. However, the choice of the density of the MS plays a vital role in isolating the aneurysm and allowing unobstructed blood flow in the branch vessel.

METHOD

In the present study, we examined 3 cases (without a stent and with single-layer and double-layer stents) via numerical simulations to explore the feasibility of the MSs used in the treatment of such aneurysms and estimate whether there is a more appropriate or optimal stent density.

RESULTS

With stent intervention, the velocity of blood flow in the sac decreased, but the pressure on the surface of the aneurysm did not decrease although it became more uniform. In addition, the "region of double low" (with low wall shear stress and a low Sherwood number) enlarged after stent implantation. Even with the double-layer stent, however, the flux of the branch vessel was still above normal, and we could predict that the optimal stent porosity was approximately 49.9%.

CONCLUSIONS

Unlike in previous studies, an MS could not be feasibly applied to high-risk PRAAs. However, an MS can induce sac thrombosis in the later stages while maintaining visceral vessel patency, and our results suggest that the optimal stent may be a 4-layer stent.

Heterogeneity in the nonplanarity and arterial curvature of arteriovenous fistulas in vivo

OBJECTIVE

Native arteriovenous fistulas (AVFs) for hemodialysis are susceptible to nonmaturation. Adverse features of local blood flow have been implicated in the formation of perianastomotic neointimal hyperplasia that may underpin nonmaturation. Whereas computational fluid dynamic simulations of idealized models highlight the importance of geometry on fluid and vessel wall interactions, little is known in vivo about AVF geometry and its role in adverse clinical outcomes. This study set out to examine the three-dimensional geometry of native AVFs and the geometric correlates of AVF failure.

METHODS

As part of an observational study between 2013 and 2016, patients underwent creation of an upper limb AVF according to current surgical best practice. Phase-contrast magnetic resonance imaging was performed on the day of surgery to obtain luminal geometry along with ultrasound measurements of flow. Magnetic resonance imaging data sets were segmented and reconstructed for quantitative and qualitative analysis of local geometry. Clinical maturation was evaluated at 6 weeks.

RESULTS

There were 60 patients who were successfully imaged on the day of surgery. Radiocephalic (n = 17), brachiocephalic (n = 40), and brachiobasilic (n = 3) fistulas were included in the study. Centerlines extracted from segmented vessel lumen exhibited significant heterogeneity in arterial nonplanarity and curvature. Furthermore, these features are more marked in brachiocephalic than in radiocephalic fistulas. Across the cohort, the projected bifurcation angle was 73 ± 16 degrees (mean ± standard deviation). Geometry was preserved at 2 weeks in 20 patients who underwent repeated imaging. A greater degree of arterial nonplanarity (log odds ratio [logOR], 0.95 per 0.1/vessel diameter; 95% confidence interval [CI], 0.22-1.90; P = .03) and a larger bifurcation angle (logOR, 0.05 per degree; 95% CI, 0.01-0.09; P = .02) are associated with a greater rate of maturation, as is fistula location (upper vs lower arm; logOR, -1.9; 95% CI, -3.2 to 0.7; P = .002).

CONCLUSIONS

There is significant heterogeneity in the three-dimensional geometry of AVFs, in particular, arterial nonplanarity and curvature. In this largest cohort of AVF geometry to date, the effect of individual geometric correlates on maturation is uncertain but supports the premise that future modeling studies will need to acknowledge the complex geometry of AVFs.

Swirling Flow and Wall Shear: Evaluating the BioMimics 3D Helical Centerline Stent for the Femoropopliteal Segment

The BioMimics 3D self-expanding nitinol stent represents a strategy for femoropopliteal intervention that is alternative or complementary to deployment of drug-coated stents or balloons. Whereas conventional straight stents reduce arterial curvature and disturb blood flow, creating areas of low wall shear, where neointimal hyperplasia predominantly develops, the helical centerline geometry of the BioMimics 3D maintains or imparts arterial curvature, promotes laminar swirling blood flow, and elevates wall shear to protect against atherosclerosis and restenosis. In the multicenter randomized MIMICS trial, treatment of femoropopliteal disease with the BioMimics 3D (n = 50) significantly improved 2-year primary patency (log-rank test p = 0.05) versus a control straight stent (n = 26), with no cases of clinically driven target lesion revascularization between 12 and 24 months (log-rank test p = 0.03 versus controls). In geometric X-ray analysis, the BioMimics stent was significantly more effective in imparting a helical shape even when the arterial segment was moderately to severely calcified. Computational fluid dynamics analysis showed that average wall shear was significantly higher with the helical centerline stent (1.13 ± 0.13 Pa versus 1.06 ± 0.12 Pa, p = 0.05). A 271-patient multicenter international MIMICS-2 trial and a 500-patient real-world MIMICS-3D registry are underway.

Optimized vascular network by stereolithography for tissue engineered skin

This paper demonstrates the essential and efficient methods to design, and fabricate optimal vascular network for tissue engineering structures based on their physiological conditions. Comprehensive physiological requirements in both micro and macro scales were considered in developing the optimisation design for complex vascular vessels. The optimised design was then manufactured by stereolithography process using materials that are biocompatible, elastic and surface bio-coatable. The materials are self-developed photocurable resin consist of BPA-ethoxylated-diacrylate, lauryl acrylate and isobornylacrylate with Irgacure® 184, the photoinitiator. The optimised vascular vessel offers many advantages: 1) it provides the maximum nutrient supply; 2) it minimises the recirculation areas and 3) it allows the wall shear stress on the vessel in a healthy range. The stereolithography manufactured vascular vessels were then embedded in the hydrogel seeded with cells. The results of in vitro studies show that the optimised vascular network has the lowest cell death rate compared with a pure hydrogel scaffold and a hydrogel scaffold embedded within a single tube in day seven. Consequently, these design and manufacture routes were shown to be viable for exploring and developing a high range complex and specialised artificial vascular networks.

Numerical identification of the rupture locations in patient-specific abdominal aortic aneurysmsusing hemodynamic parameters

The rupture of an abdominal aortic aneurysm (AAA) is generally an unexpected event. Up to now, there is no agreement on an accurate criteria to predict the rupture risk of AAAs. This paper aims to numerically investigate the hemodynamics of three ruptured and one non-ruptured patient-specific AAA models to correlate local hemodynamic parameters with the rupture sites, and for the first time, this study introduced helicity as a potential index for the rupture potential of AAAs.3D reconstructions from CT scans were done. The simulation revealed that all the rupture sites were in regions of stagnation with near zero wall shear stress (WSS) but large WSS gradient (WSSG), which may explain the observation by the former researchers that the rupture site in the ruptured AAA has the lowest recorded wall thickness compared to other non-ruptured regions. Moreover, all the ruptures occurred at regions of zero helicity which represents a purely axial or circumferential flow. In addition, this study revealed that the double low region for the non-ruptured AAA was present with a thick layer of plaques, it suggests that the AAA rupture and the formation of atherosclerotic plaques may share a lot common physiological features. However, the fact that there are no plaques present in the walls of three RAAAs also indicates that AAA is not always a result of atherosclerosis. The current computational study may complement the maximum diameter, peak wall stress and other clinically relevant factors in AAA ruptures to identify the rupture sites of AAAs.

Helical Centerline Stent Improves Patency: Two-Year Results From the Randomized Mimics Trial

BACKGROUND

Reintervention in the femoropopliteal artery is frequent and a major driver of cost-effectiveness. High wall shear generated by swirling blood flow is associated with reduced occurrence of atherosclerosis and restenosis. This trial investigated the clinical and hemodynamic outcomes of the BioMimics 3D self-expanding tubular nitinol stent with helical centerline geometry compared with a straight stent in the femoropopliteal artery.

METHODS AND RESULTS

In a prospective, multicenter, randomized controlled trial, 76 patients with symptomatic peripheral arterial disease were randomized 2:1 to receive a helical or a straight stent. An independent core laboratory adjudicated angiographic and ultrasound parameters. The primary safety end point was freedom from a composite of all death, target limb amputation, and target lesion revascularization at 30 days. The primary effectiveness end point was freedom from clinically driven target lesion revascularization at 6 months. Patency was a secondary end point. Subjects were followed up for 2 years from intervention. The primary safety (1-sided P<0.01) and efficacy (1-sided P<0.001) end points for the helical stent were met. The proportion of patients treated with the helical stent who maintained patency at 12 and 24 months was 80% and 72%, respectively, compared with 71% and 55% for the control group. The difference was significant through 24 months (P=0.05). Freedom from clinically driven target lesion revascularization for the helical compared with straight stent was 91% versus 92% at 12 months and 91% versus 76% at 24 months.

CONCLUSIONS

Both groups had similar safety outcomes and clinically driven target lesion revascularization to 2 years. However, after placement of a BioMimics 3D helical stent, there was improved patency to 2 years.

CLINICAL TRIAL REGISTRATION

URL: http://www.clinicaltrials.gov. Unique identifier: NCT02163863.

Cigarette smoke extract counteracts atheroprotective effects of high laminar flow on endothelial function

Tobacco smoking and hemodynamic forces are key stimuli in the development of endothelial dysfunction and atherosclerosis. High laminar flow has an atheroprotective effect on the endothelium and leads to a reduced response of endothelial cells to cardiovascular risk factors compared to regions with disturbed or low laminar flow. We hypothesize that the atheroprotective effect of high laminar flow could delay the development of endothelial dysfunction caused by cigarette smoking. Primary human endothelial cells were stimulated with increasing dosages of aqueous cigarette smoke extract (CSEaq). CSEaq reduced cell viability in a dose-dependent manner. The main mediator of cellular adaption to oxidative stress, nuclear factor erythroid 2-related factor 2 (NRF2) and its target genes heme oxygenase (decycling) 1 (HMOX1) or NAD(P)H quinone dehydrogenase 1 (NQO1) were strongly increased by CSEaq in a dose-dependent manner. High laminar flow induced elongation of endothelial cells in the direction of flow, activated the AKT/eNOS pathway, increased eNOS expression, phosphorylation and NO release. These increases were inhibited by CSEaq. Pro-inflammatory adhesion molecules intercellular adhesion molecule-1 (ICAM1), vascular cell adhesion molecule-1 (VCAM1), selectin E (SELE) and chemokine (C-C motif) ligand 2 (CCL2/MCP-1) were increased by CSEaq. Low laminar flow induced VCAM1 and SELE compared to high laminar flow. High laminar flow improved endothelial wound healing. This protective effect was inhibited by CSEaq in a dose-dependent manner through the AKT/eNOS pathway. Low as well as high laminar flow decreased adhesion of monocytes to endothelial cells. Whereas, monocyte adhesion was increased by CSEaq under low laminar flow, this was not evident under high laminar flow. This study shows the activation of major atherosclerotic key parameters by CSEaq. Within this process, high laminar flow is likely to reduce the harmful effects of CSEaq to a certain degree. The identified molecular mechanisms might be useful for development of alternative therapy concepts.

The Effect of Arterial Curvature on Blood Flow in Arterio-Venous Fistulae: Realistic Geometries and Pulsatile Flow

Arterio-Venous Fistulae (AVF) are regarded as the "gold standard" method of vascular access for patients with End-Stage Renal Disease (ESRD) who require haemodialysis. However, up to 60% of AVF do not mature, and hence fail, as a result of Intimal Hyperplasia (IH). Unphysiological flow and oxygen transport patterns, associated with the unnatural and often complex geometries of AVF, are believed to be implicated in the development of IH. Previous studies have investigated the effect of arterial curvature on blood flow in AVF using idealized planar AVF configurations and non-pulsatile inflow conditions. The present study takes an important step forwards by extending this work to more realistic non-planar brachiocephalic AVF configurations with pulsatile inflow conditions. Results show that forming an AVF by connecting a vein onto the outer curvature of an arterial bend does not, necessarily, suppress unsteady flow in the artery. This finding is converse to results from a previous more idealized study. However, results also show that forming an AVF by connecting a vein onto the inner curvature of an arterial bend can suppress exposure to regions of low wall shear stress and hypoxia in the artery. This finding is in agreement with results from a previous more idealized study. Finally, results show that forming an AVF by connecting a vein onto the inner curvature of an arterial bend can significantly reduce exposure to high WSS in the vein. The results are important, as they demonstrate that in realistic scenarios arterial curvature can be leveraged to reduce exposure to excessively low/high levels of WSS and regions of hypoxia in AVF. This may in turn reduce rates of IH and hence AVF failure.

Design and Comparison of Large Vessel Stents: Balloon Expandable and Self-Expanding Peripheral Arterial Stents

Endovascular stenting has evolved over the last 50 years since its inception into the framework of management of vascular atherosclerotic disease. Stent design has evolved as lesion complexity has increased. Nevertheless, certain first principles regarding stent design have been recapitulated time and again with every iteration of endovascular stents. This article reviews principles of endovascular stent design and compares and contrasts key aspects of balloon expandable and self-expanding stents.

Mathematical Analysis and Physical Profile of Blalock-Taussig Shunt and Sano Modification Procedure in Hypoplastic Left Heart Syndrome: Review of the Literature and Implications for the Anesthesiologist

The first stage of surgical treatment for hypoplastic left heart syndrome (HLHS) includes the creation of artificial systemic-to-pulmonary connections to provide pulmonary blood flow. The modified Blalock-Taussig (mBT) shunt has been the technique of choice for this procedure; however, a right ventricle-pulmonary artery (RV-PA) shunt has been introduced into clinical practice with encouraging but still conflicting outcomes when compared with the mBT shunt. The aim of this study is to explore mathematical modeling as a tool for describing physical profiles that could assist the surgical team in predicting complications related to stenosis and malfunction of grafts in an attempt to find correlations with clinical outcomes from clinical studies that compared both surgical techniques and to assist the anesthesiologist in making decisions to manage patients with this complex cardiac anatomy. Mathematical modeling to display the physical characteristics of the chosen surgical shunt is a valuable tool to predict flow patterns, shear stress, and rate distribution as well as energetic performance at the graft level and relative to ventricular efficiency. Such predictions will enable the surgical team to refine the technique so that hemodynamic complications be anticipated and prevented, and are also important for perioperative management by the anesthesia team.

Numerical Assessment of Novel Helical/Spiral Grafts with Improved Hemodynamics for Distal Graft Anastomoses

In the present work, numerical simulations were conducted for a typical end-to-side distal graft anastomosis to assess the effects of inducing secondary flow, which is believed to remove unfavourable flow environment. Simulations were carried out for four models, generated based on two main features of 'out-of-plane helicity' and 'spiral ridge' in the grafts as well as their combination. Following a qualitative comparison against in vitro data, various mean flow and hemodynamic parameters were compared and the results showed that helicity is significantly more effective in inducing swirling flow in comparison to a spiral ridge, while their combination could be even more effective. In addition, the induced swirling flow was generally found to be increasing the wall shear stress and reducing the flow stagnation and particle residence time within the anastomotic region and the host artery, which may be beneficial to the graft longevity and patency rates. Finally, a parametric study on the spiral ridge geometrical features was conducted, which showed that the ridge height and the number of spiral ridges have significant effects on inducing swirling flow, and revealed the potential of improving the efficiency of such designs.

Engineering design of artificial vascular junctions for 3D printing

Vascular vessels, including arteries, veins and capillaries, are being printed using additive manufacturing technologies, also known as 3D printing. This paper demonstrates that it is important to follow the vascular design by nature as close as possible when 3D printing artificial vascular branches. In previous work, the authors developed an algorithm of computational geometry for constructing smooth junctions for 3D printing. In this work, computational fluid dynamics (CFDs) is used to compare the wall shear stress and blood velocity field for the junctions of different designs. The CFD model can reproduce the expected wall shear stress at locations remote from the junction. For large vessels such as veins, it is shown that ensuring the smoothness of the junction and using smaller joining angles as observed in nature is very important to avoid high wall shear stress and recirculation. The issue is however less significant for capillaries. Large joining angles make no difference to the hemodynamic behavior, which is also consistent with the fact that most capillary junctions have large joining angles. The combination of the CFD analysis and the junction construction method form a complete design method for artificial vascular vessels that can be 3D printed using additive manufacturing technologies.

Hemodynamics

A review is presented of the physical principles governing the distribution of blood flow and blood pressure in the vascular system. The main factors involved are the pulsatile driving pressure generated by the heart, the flow characteristics of blood, and the geometric structure and mechanical properties of the vessels. The relationship between driving pressure and flow in a given vessel can be understood by considering the viscous and inertial forces acting on the blood. Depending on the vessel diameter and other physical parameters, a wide variety of flow phenomena can occur. In large arteries, the propagation of the pressure pulse depends on the elastic properties of the artery walls. In the microcirculation, the fact that blood is a suspension of cells strongly influences its flow properties and leads to a nonuniform distribution of hematocrit among microvessels. The forces acting on vessel walls include shear stress resulting from blood flow and circumferential stress resulting from blood pressure. Biological responses to these forces are important in the control of blood flow and the structural remodeling of vessels, and also play a role in major disease processes including hypertension and atherosclerosis. Consideration of hemodynamics is essential for a comprehensive understanding of the functioning of the circulatory system.

Drug-Eluting Stent Design is a Determinant of Drug Concentration at the Endothelial Cell Surface

Although drug-eluting stents (DES) have greatly reduced arterial restenosis, there are persistent concerns about stent thrombosis. DES thrombosis is attributable to retarded vascular re-endothelialization due to both stent-induced flow disturbance and the inhibition by the eluted drug of endothelial cell proliferation and migration. The present computational study aims to determine the effect of DES design on both stent-induced flow disturbance and the concentration of eluted drug at the arterial luminal surface. To this end, we consider three closed-cell stent designs that resemble certain commercial stents as well as three "idealized" stents that provide insight into the impact of specific characteristics of stent design. To objectively compare the different stents, we introduce the Stent Penalty Index (SPI), a dimensionless quantity whose value increases with both the extent of flow disturbance and luminal drug concentration. Our results show that among the three closed-cell designs studied, wide cell designs lead to lower SPI and are thus expected to have a less adverse effect on vascular re-endothelialization. For the idealized stent designs, a spiral stent provides favorable SPI values, whereas an intertwined ring stent leads to an elevated SPI. The present findings shed light onto the effect of stent design on the concentration of the eluted drug at the arterial luminal surface, an important consideration in the assessment of DES performance.

Microbubble Void Imaging: A Non-invasive Technique for Flow Visualisation and Quantification of Mixing in Large Vessels Using Plane Wave Ultrasound and Controlled Microbubble Contrast Agent Destruction

There is increasing recognition of the influence of the flow field on the physiology of blood vessels and their development of pathology. Preliminary work is reported on a novel non-invasive technique, microbubble void imaging, which is based on ultrasound and controlled destruction of microbubble contrast agents, permitting flow visualisation and quantification of flow-induced mixing in large vessels. The generation of microbubble voids can be controlled both spatially and temporally using ultrasound parameters within the safety limits. Three different model vessel geometries-straight, planar-curved and helical-with known effects on the flow field and mixing were chosen to evaluate the technique. A high-frame-rate ultrasound system with plane wave transmission was used to acquire the contrast-enhanced ultrasound images, and an entropy measure was calculated to quantify mixing. The experimental results were cross-compared between the different geometries and with computational fluid dynamics. The results indicated that the technique is able to quantify the degree of mixing within the different configurations, with a helical geometry generating the greatest mixing, and a straight geometry, the lowest. There is a high level of concordance between the computational fluid dynamics and experimental results. The technique could also serve as a flow visualisation tool.

Haemodynamics and Flow Modification Stents for Peripheral Arterial Disease: A Review

Endovascular stents are widely used for the treatment of peripheral arterial disease (PAD). However, the development of in-stent restenosis and downstream PAD progression remain a challenge. Stent revascularisation of PAD causes arterial trauma and introduces abnormal haemodynamics, which initiate complicated biological processes detrimental to the arterial wall. The interaction between stent struts and arterial cells in contact, and the blood flow field created in a stented region, are highly affected by stent design. Spiral flow is known as a normal physiologic characteristic of arterial circulation and is believed to prevent the development of flow disturbances. This secondary flow motion is lost in atheromatous disease and its re-introduction after endovascular treatment of PAD has been suggested as a method to induce stabilised and coherent haemodynamics. Stent designs able to generate spiral flow may support endothelial function and therefore increase patency rates. This review is focused on secondary flow phenomena in arteries and the development of flow modification stent technologies for the treatment of PAD.

Critical evaluation of three hemodynamic models for the numerical simulation of intra-stent flows

We evaluate here three hemodynamic models used for the numerical simulation of bare and stented artery flows. We focus on two flow features responsible for intra-stent restenosis: the wall shear stress and the re-circulation lengths around a stent. The studied models are the Poiseuille profile, the simplified pulsatile profile and the complete pulsatile profile based on the analysis of Womersley. The flow rate of blood in a human left coronary artery is considered to compute the velocity profiles. "Ansys Fluent 14.5" is used to solve the Navier-Stokes and continuity equations. As expected our results show that the Poiseuille profile is questionable to simulate the complex flow dynamics involved in intra-stent restenosis. Both pulsatile models give similar results close to the strut but diverge far from it. However, the computational time for the complete pulsatile model is five times that of the simplified pulsatile model. Considering the additional "cost" for the complete model, we recommend using the simplified pulsatile model for future intra-stent flow simulations.

Effect of swirling blood flow on vortex formation at post-stenosis

Various clinical observations reported that swirling blood flow is a normal physiological flow pattern in various vasculatures. The swirling flow has beneficial effects on blood circulation through the blood vessels. It enhances oxygen transfer and reduces low-density lipoprotein concentration in the blood vessel by enhancing cross-plane mixing of the blood. However, the fluid-dynamic roles of the swirling flow are not yet fully understood. In this study, inhibition of material deposition at the post-stenosis region by the swirling flow was observed. To reveal the underlying fluid-dynamic characteristics, pathline flow visualization and time-resolved particle image velocimetry measurements were conducted. Results showed that the swirling inlet flow increased the development of vortices at near wall region of the post-stenosis, which can suppress further development of stenosis by enhancing transport and mixing of the blood flow. The fluid-dynamic characteristics obtained in this study would be useful for improving hemodynamic characteristics of vascular grafts and stents in which the stenosis frequently occurred. Moreover, the time-resolved particle image velocimetry measurement technique and vortex identification method employed in this study would be useful for investigating the fluid-dynamic effects of the swirling flow on various vascular environments.

The effect of in-plane arterial curvature on blood flow and oxygen transport in arterio-venous fistulae

Arterio-Venous Fistulae (AVF) are the preferred method of vascular access for patients with end stage renal disease who need hemodialysis. In this study, simulations of blood flow and oxygen transport were undertaken in various idealized AVF configurations. The objective of the study was to understand how arterial curvature affects blood flow and oxygen transport patterns within AVF, with a focus on how curvature alters metrics known to correlate with vascular pathology such as Intimal Hyperplasia (IH). If one subscribes to the hypothesis that unsteady flow causes IH within AVF, then the results suggest that in order to avoid IH, AVF should be formed via a vein graft onto the outer-curvature of a curved artery. However, if one subscribes to the hypothesis that low wall shear stress and/or low lumen-to-wall oxygen flux (leading to wall hypoxia) cause IH within AVF, then the results suggest that in order to avoid IH, AVF should be formed via a vein graft onto a straight artery, or the inner-curvature of a curved artery. We note that the recommendations are incompatible-highlighting the importance of ascertaining the exact mechanisms underlying development of IH in AVF. Nonetheless, the results clearly illustrate the important role played by arterial curvature in determining AVF hemodynamics, which to our knowledge has been overlooked in all previous studies.

Fluid-dynamic optimal design of helical vascular graft for stenotic disturbed flow

Although a helical configuration of a prosthetic vascular graft appears to be clinically beneficial in suppressing thrombosis and intimal hyperplasia, an optimization of a helical design has yet to be achieved because of the lack of a detailed understanding on hemodynamic features in helical grafts and their fluid dynamic influences. In the present study, the swirling flow in a helical graft was hypothesized to have beneficial influences on a disturbed flow structure such as stenotic flow. The characteristics of swirling flows generated by helical tubes with various helical pitches and curvatures were investigated to prove the hypothesis. The fluid dynamic influences of these helical tubes on stenotic flow were quantitatively analysed by using a particle image velocimetry technique. Results showed that the swirling intensity and helicity of the swirling flow have a linear relation with a modified Germano number (Gn*) of the helical pipe. In addition, the swirling flow generated a beneficial flow structure at the stenosis by reducing the size of the recirculation flow under steady and pulsatile flow conditions. Therefore, the beneficial effects of a helical graft on the flow field can be estimated by using the magnitude of Gn*. Finally, an optimized helical design with a maximum Gn* was suggested for the future design of a vascular graft.

From Histology and Imaging Data to Models for In-Stent Restenosis

The implantation of stents has been used to treat coronary artery stenosis for several decades. Although stenting is successful in restoring the vessel lumen and is a minimally invasive approach, the long-term outcomes are often compromised by in-stent restenosis (ISR). Animal models have provided insights into the pathophysiology of ISR and are widely used to evaluate candidate drug inhibitors of ISR. Such biological models allow the response of the vessel to stent implantation to be studied without the variation of lesion characteristics encountered in patient studies.

This paper describes the development of complementary in silico models employed to improve the understanding of the biological response to stenting using a porcine model of restenosis. This includes experimental quantification using microCT imaging and histology and the use of this data to establish numerical models of restenosis. Comparison of in silico results with histology is used to examine the relationship between spatial localization of fluid and solid mechanics stimuli immediately post-stenting. Multi-scale simulation methods are employed to study the evolution of neointimal growth over time and the variation in the extent of neointimal hyperplasia within the stented region. Interpretation of model results through direct comparison with the biological response contributes to more detailed understanding of the pathophysiology of ISR, and suggests the focus for follow-up studies.

In conclusion we outline the challenges which remain to both complete our understanding of the mechanisms responsible for restenosis and translate these models to applications in stent design and treatment planning at both population-based and patient-specific levels.

Simulation of oxygen transfer in stented arteries and correlation with in-stent restenosis

Computational models are used to study the combined effect of biomechanical and biochemical factors on coronary in-stent restenosis, which is a postoperative remodeling and regrowth pathology of the stented arteries. More precisely, we address numerical simulations, on the basis of Navier-Stokes and mass transport equations, to study the role of perturbed wall shear stresses and reduced oxygen concentration in a geometrical model reconstructed from a real porcine artery treated with a stent. Joining in vivo and in silico tools of investigation has multiple benefits in this case. On one hand, the geometry of the arterial wall and of the stent closely correspond to a real implanted configuration. On the other hand, the inspection of histological tissue samples informs us on the location and intensity of in-stent restenosis. As a result, we are able to correlate geometrical factors, such as the axial variation of the artery diameter and its curvature; the numerical quantification of biochemical stimuli, such as wall shear stresses; and the availability of oxygen to the inner layers of the artery, with the appearance of in-stent restenosis. This study shows that the perturbation of the vessel curvature could induce hemodynamic conditions that stimulate undesired arterial remodeling.

Intimal hyperplasia following implantation of helical-centreline and straight-centreline stents in common carotid arteries in healthy pigs: influence of intraluminal flow

Intimal hyperplasia (IH) is a leading cause of obstruction of vascular interventions, including arterial stents, bypass grafts and arteriovenous grafts and fistulae. Proposals to account for arterial stent-associated IH include wall damage, low wall shear stress (WSS), disturbed flow and, although not widely recognized, wall hypoxia. The common non-planarity of arterial geometry and flow, led us to develop a bare-metal, nitinol, self-expanding stent with three-dimensional helical-centreline geometry. This was deployed in one common carotid artery of healthy pigs, with a straight-centreline, but otherwise identical (conventional) stent deployed contralaterally. Both stent types deformed the arteries, but the helical-centreline device additionally deformed them helically and caused swirling of intraluminal flow. At sacrifice, one month post stent deployment, histology revealed significantly less IH in the helical-centreline than straight-centreline stented vessels. Medial cross-sectional area was not significantly different in helical-centreline than straight-centreline stented vessels. By contrast, luminal cross-sectional area was significantly larger in helical-centreline than straight-centreline stented vessels. Mechanisms considered to account for those results include enhanced intraluminal WSS and enhanced intraluminal blood-vessel wall mass transport, including of oxygen, in the helical-centreline stented vessels. Consistent with the latter proposal, adventitial microvessel density was lower in the helical-centreline stented than straight-centreline stented vessels.

A computational exploration of helical arterio-venous graft designs

Although arterio-venous grafts (AVGs) are the second best option as long-term vascular access for hemodialysis, they suffer from complications caused by intimal hyperplasia, mainly located in vessel regions of low and oscillating wall shear stress. However, certain flow patterns in the bulk may reduce these unfavorable hemodynamic conditions. We therefore studied, with computational fluid dynamics (CFD), the impact of a helical AVG design on the occurrence of (un)favorable hemodynamic conditions at the venous anastomosis. Six CFD-models of an AVG in closed-loop configuration were constructed: one conventional straight graft, and five helical designed grafts with a pitch of 105 mm down to 35 mm. At the venous anastomosis, disturbed shear was assessed by quantifying the area with unfavorable conditions, and by analyzing averaged values in a case-specific patch. The bulk hemodynamics were assessed by analyzing the kinetic helicity in and the pressure drop over the graft. The most helical design scores best, being instrumental to suppress disturbed shear in the venous segment. There is, however, no trivial relationship between the number of helix turns of the graft and disturbed shear in the venous segment, when a realistic closed-loop AVG model is investigated. Bulk flow investigation showed a marked increase of helicity intensity in, and a moderate pressure drop over the AVG by introducing a lower pitch. At the venous anastomosis, unfavorable hemodynamic conditions can be reduced by introducing a helical design. However, due to the complex flow conditions, the optimal helical design for an AVG cannot be derived without studying case by case.

Index proposal and basic estimator study for quantification of oscillation of the secondary flow pattern in tortuous vessels

The development of atherosclerosis has been shown to correlate with regions of low wall shear stress and seemingly reduced mass transport. The local tortuosity of the arteries and local secondary flow oscillation also seem to be negatively correlated with the local occurrence of the disease. However there is currently no tool or physiological parameter that can be measured non-invasively to assess the local oscillation of the flow. Standard Colour Doppler imaging of secondary flow patterns during the blood pulse is studied and illustrated, and the local oscillation of the secondary flow pattern is proposed as an index, which could be an indicator of the likelihood of future disease development. Preliminary results are presented using a basic estimator developed for the proof of concept in the case of swirling flow, and based on colour-coded video signals collected in different configurations. In vitro results show that there is a correspondence between the Doppler patterns and the secondary flow patterns, the repeatability of the measures, and that the proposed index and its estimator reflect a joint influence of the local oscillation of the secondary flow pattern and of the flow rate. On another hand, while in vivo results still suffer from instabilities, noise and from scanners and processing limitations, they demonstrate that it is possible to use Colour Doppler imaging to image and characterize in vivo the secondary flow patterns and their oscillations non-invasively, and that it is possible for a trained clinician to perform manually such Doppler measurements for processing.

Macro-scale phenomena of arterial coupled cells: a massively parallel simulation

Impaired mass transfer characteristics of blood-borne vasoactive species such as adenosine triphosphate in regions such as an arterial bifurcation have been hypothesized as a prospective mechanism in the aetiology of atherosclerotic lesions. Arterial endothelial cells (ECs) and smooth muscle cells (SMCs) respond differentially to altered local haemodynamics and produce coordinated macro-scale responses via intercellular communication. Using a computationally designed arterial segment comprising large populations of mathematically modelled coupled ECs and SMCs, we investigate their response to spatial gradients of blood-borne agonist concentrations and the effect of micro-scale-driven perturbation on the macro-scale. Altering homocellular (between same cell type) and heterocellular (between different cell types) intercellular coupling, we simulated four cases of normal and pathological arterial segments experiencing an identical gradient in the concentration of the agonist. Results show that the heterocellular calcium (Ca(2+)) coupling between ECs and SMCs is important in eliciting a rapid response when the vessel segment is stimulated by the agonist gradient. In the absence of heterocellular coupling, homocellular Ca(2+) coupling between SMCs is necessary for propagation of Ca(2+) waves from downstream to upstream cells axially. Desynchronized intracellular Ca(2+) oscillations in coupled SMCs are mandatory for this propagation. Upon decoupling the heterocellular membrane potential, the arterial segment looses the inhibitory effect of ECs on the Ca(2+) dynamics of the underlying SMCs. The full system comprises hundreds of thousands of coupled nonlinear ordinary differential equations simulated on the massively parallel Blue Gene architecture. The use of massively parallel computational architectures shows the capability of this approach to address macro-scale phenomena driven by elementary micro-scale components of the system.