Rounded Layering Transitions on the Surface of Ice

Precisely Controlled Polymerization of Two-Dimensional Conducting Polymers in Quasi-Liquid Layer Enables Ultrahigh Sensing Performance

Gas sensors based on conducting polymers offer great potential for high-performance room temperature applications due to their cost-effectiveness, high-sensitivity, and operational advantage. However, their current performance is limited by the deficiency of control in conventional polymerization methods, leading to poor crystallinity and inconsistent material properties. Here, the quasi-liquid layer (QLL) on the ice surface acts as a self-regulating nano-reactor for precise control of thermodynamics and kinetics in the polymerization, resulting in a 7.62 nm thick two-dimensional (2D) polyaniline (PANI) film matching the QLL thickness. The ultra-thin film optimizes the exposure of active sites, enhancing the detection of analyte gases at low concentrations. It is validated by fabricating a chemiresistive gas sensor with the 2D PANI film, demonstrating stable room-temperature detection of ammonia down to 10 ppt in ambient air with an impressive 10% response. This achievement represents the highest sensitivity among sensors of this kind while maintaining excellent selectivity and repeatability. Moreover, the QLL-controlled polymerization strategy offers an alternative route for precise control of the polymerization process for conducting polymers, enabling the creation of advanced materials with enhanced properties.

Hierarchical Structuring of Black Silicon Wafers by Ion-Flow-Stimulated Roughening Transition: Fundamentals and Applications for Photovoltaics

Ion-flow-stimulated roughening transition is a phenomenon that may prove useful in the hierarchical structuring of nanostructures. In this work, we have investigated theoretically and experimentally the surface texturing of single-crystal and multi-crystalline silicon wafers irradiated using ion-beam flows. In contrast to previous studies, ions had relatively low energies, whereas flow densities were high enough to induce a quasi-liquid state in the upper silicon layers. The resulting surface modifications reduced the wafer light reflectance to values characteristic of black silicon, widely used in solar energetics. Features of nanostructures on different faces of silicon single crystals were studied numerically based on the mesoscopic Monte Carlo model. We established that the formation of nano-pyramids, ridges, and twisting dune-like structures is due to the stimulated roughening transition effect. The aforementioned variety of modified surface morphologies arises due to the fact that the effects of stimulated surface diffusion of atoms and re-deposition of free atoms on the wafer surface from the near-surface region are manifested to different degrees on different Si faces. It is these two factors that determine the selection of the allowable "trajectories" (evolution paths) of the thermodynamic system along which its Helmholtz free energy, F, decreases, concomitant with an increase in the surface area of the wafer and the corresponding changes in its internal energy, U (dU>0), and entropy, S (dS>0), so that dF=dU - TdS<0, where T is the absolute temperature. The basic theoretical concepts developed were confirmed in experimental studies, the results of which showed that our method could produce, abundantly, black silicon wafers in an environmentally friendly manner compared to traditional chemical etching.

Self-diffusion and shear viscosity for the TIP4P/Ice water model

With an ever-increasing interest in water properties, many intermolecular force fields have been proposed to describe the behavior of water. Unfortunately, good models for liquid water usually cannot provide simultaneously an accurate melting point for ice. For this reason, the TIP4P/Ice model was developed for targeting the melting point and has become the preferred choice for simulating ice at coexistence. Unfortunately, available data for its dynamic properties in the liquid state are scarce. Therefore, we demonstrate a series of simulations aimed at the calculation of transport coefficients for the TIP4P/Ice model over a large range of thermodynamic conditions, ranging from T = 245 K to T = 350 K, for the temperature, and from p = 0 to p = 500 MPa, for the pressure. We have found that the self-diffusion (shear viscosity) exhibits smaller (increased) values than TIP4P/2005 and experiments. However, rescaling the temperature with respect to the triple point temperature, as in a corresponding states plot, we find that TIP4P/Ice compares very well with TIP4P/2005 and experiment. Such observations allow us to infer that despite the different original purposes of these two models examined here, one can benefit from a vast number of reports regarding the behavior of transport coefficients for the TIP4P/2005 model and utilize them following the routine described in this paper.

Effect of sodium chloride adsorption on the surface premelting of ice

We characterise the structural properties of the quasi-liquid layer (QLL) at two low-index ice surfaces in the presence of sodium chloride (Na⁺/Cl^-) ions by molecular dynamics simulations. We find that the presence of a high surface density of Na⁺/Cl^- pairs changes the surface melting behaviour from step-wise to gradual melting. The ions lead to an overall increase of the thickness and the disorder of the QLL, and to a low-temperature roughening transition of the air-ice interface. The local molecular structure of the QLL is similar to that of liquid water, and the differences between the basal and primary prismatic surface are attenuated by the presence of Na⁺/Cl^- pairs. These changes modify the crystal growth rates of different facets and the solvation environment at the surface of sea-water ice with a potential impact on light scattering and environmental chemical reactions.

Intermolecular forces at ice and water interfaces: premelting, surface freezing and regelation

Using Lifshitz theory we assess the role of van der Waals forces at interfaces of ice and water. The results are combined with measured structural forces from computer simulations to develop a quantitative model of the surface free energy of premelting films. This input is employed within the framework of wetting theory and allows us to predict qualitatively the behavior of quasi-liquid layer thickness as a function of ambient conditions. Our results emphasize the significance of vapor pressure. The ice vapor interface is shown to exhibit only incomplete premelting, but the situation can shift to a state of complete surface melting above water saturation. The results obtained serve also to assess the role of subsurface freezing at the water-vapor interface, and we show that intermolecular forces favor subsurface ice nucleation only in conditions of water undersaturation. We show ice regelation at ambient pressure may be explained as a process of capillary freezing, without the need to invoke the action of bulk pressure melting. Our results for van der Waals forces are exploited in order to gauge dispersion interactions in empirical point charge models of water.

Premelting layer during ice growth: role of clusters

The premelting layer plays an important role in ice growth, but there is a significant gap in our knowledge between the atomistic premelting surface structure and the macroscopic growth mechanism. In this work, using large-scale molecular dynamics simulation, we reveal the existence of clusters on the premelting surface, as an intermediate feature bridging the gap. We show the spontaneous formation and evolution of clusters, and they form a stable distribution determined by the growth rate. We demonstrate how this stable distribution is related to the growth mode of ice, connected by the growth of clusters. We come to a bilayer-by-bilayer growth mode at simulation-reachable high growth rates, but another mechanism, namely "cluster stacking", is speculated to exist at lower growth rates. This work builds a connection between the microscopic structure of the premelting layer and the macroscopic growth of ice, making a step forward toward the full understanding of premelting and ice growth.

How ice grows from premelting films and water droplets

Close to the triple point, the surface of ice is covered by a thin liquid layer (so-called quasi-liquid layer) which crucially impacts growth and melting rates. Experimental probes cannot observe the growth processes below this layer, and classical models of growth by vapor deposition do not account for the formation of premelting films. Here, we develop a mesoscopic model of liquid-film mediated ice growth, and identify the various resulting growth regimes. At low saturation, freezing proceeds by terrace spreading, but the motion of the buried solid is conveyed through the liquid to the outer liquid-vapor interface. At higher saturations water droplets condense, a large crater forms below, and freezing proceeds undetectably beneath the droplet. Our approach is a general framework that naturally models freezing close to three phase coexistence and provides a first principle theory of ice growth and melting which may prove useful in the geosciences.