A 14-Bit, 12 V-to-100 V Voltage Compliance Electrical Stimulator with Redundant Digital Calibration

Electrical stimulation is an important technique for modulating the functions of the nervous system through electrical stimulus. To implement a more competitive prototype that can tackle the domain-specific difficulties of existing electrical stimulators, three key techniques are proposed in this work. Firstly, a load-adaptive power saving technique called over-voltage detection is implemented to automatically adjust the supply voltage. Secondly, redundant digital calibration (RDC) is proposed to improve current accuracy and ensure safety during long-term electrical stimulation without costing too much circuit area and power. Thirdly, a flexible waveform generator is designed to provide arbitrary stimulus waveforms for particular applications. Measurement results show the stimulator can adjust the supply voltage from 12 V to 100 V automatically, and the measured effective resolution of the stimulation current reaches 14 bits in a full range of 6.5 mA. Without applying charge balancing techniques, the average mismatch between the cathodic and anodic current pulses in biphasic stimulus is 0.0427%. The proposed electrical stimulator can generate arbitrary stimulus waveforms, including sine, triangle, rectangle, etc., and it is supposed to be competitive for implantable and wearable devices.

Advanced Metallic and Polymeric Coatings for Neural Interfacing: Structures, Properties and Tissue Responses

Neural electrodes are essential for nerve signal recording, neurostimulation, neuroprosthetics and neuroregeneration, which are critical for the advancement of brain science and the establishment of the next-generation brain-electronic interface, central nerve system therapeutics and artificial intelligence. However, the existing neural electrodes suffer from drawbacks such as foreign body responses, low sensitivity and limited functionalities. In order to overcome the drawbacks, efforts have been made to create new constructions and configurations of neural electrodes from soft materials, but it is also more practical and economic to improve the functionalities of the existing neural electrodes via surface coatings. In this article, recently reported surface coatings for neural electrodes are carefully categorized and analyzed. The coatings are classified into different categories based on their chemical compositions, i.e., metals, metal oxides, carbons, conducting polymers and hydrogels. The characteristic microstructures, electrochemical properties and fabrication methods of the coatings are comprehensively presented, and their structure-property correlations are discussed. Special focus is given to the biocompatibilities of the coatings, including their foreign-body response, cell affinity, and long-term stability during implantation. This review article can provide useful and sophisticated insights into the functional design, material selection and structural configuration for the next-generation multifunctional coatings of neural electrodes.

Electrochemical and biological characterization of thin-film platinum-iridium alloy electrode coatings: a chronic in vivo study

OBJECTIVE

To evaluate the electrochemical properties, biological response, and surface characterization of an electrodeposited Platinum-Iridium (Pt-Ir) electrode coating on cochlear implants subjected to chronic stimulation in vivo.

APPROACH

Electrochemical impedance spectroscopy (EIS), charge storage capacity (CSC), charge injection limit (CIL), and voltage transient (VT) impedance were measured bench-top before and after implant and in vivo. Coated Pt-Ir and uncoated Pt electrode arrays were implanted into cochlea of normal hearing rats and stimulated for ∼4 h d, 5 d week^-1 for 5 weeks at levels within the normal clinical range. Neural function was monitored using electrically-evoked auditory brainstem responses. After explant, the electrode surfaces were assessed, and cochleae examined histologically.

MAIN RESULTS

When measured on bench-top before and after stimulation, Pt-Ir coated electrodes had significantly lower VT impedance (p < 0.001) and significantly higher CSC (p < 0.001) and CIL (p < 0.001) compared to uncoated Pt electrodes. In vivo, the CSC and CIL of Pt-Ir were significantly higher than Pt throughout the implantation period (p= 0.047 and p< 0.001, respectively); however, the VT impedance (p= 0.3) was not. There was no difference in foreign body response between material cohorts, although cochleae implanted with coated electrodes contained small deposits of Pt-Ir. There was no evidence of increased neural loss or loss of neural function in either group. Surface examination revealed no Pt corrosion on any electrodes.

SIGNIFICANCE

Electrodeposited Pt-Ir electrodes demonstrated significant improvements in electrochemical performance on the bench-top and in vivo compared to uncoated Pt. Neural function and tissue response to Pt-Ir electrodes were not different from uncoated Pt, despite small deposits of Pt-Ir in the tissue capsule. Electrodeposited Pt-Ir coatings offer promise as an improved electrode coating for active neural prostheses.

A fully intraocular high-density self-calibrating epiretinal prosthesis

This paper presents a fully intraocular self-calibrating epiretinal prosthesis with 512 independent channels in 65 nm CMOS. A novel digital calibration technique matches the biphasic currents of each channel independently while the calibration circuitry is shared among every 4 channels. Dual-band telemetry for power and data with on-chip rectifier and clock recovery reduces the number of off-chip components. The rectifier utilizes unidirectional switches to prevent reverse conduction loss in the power transistors and achieves an efficiency > 80%. The data telemetry implements a phase-shift keying (PSK) modulation scheme and supports data rates up to 20 Mb/s. The system occupies an area of 4.5 ×3.1 mm². It features a pixel size of 0.0169 mm² and arbitrary waveform generation per channel. In vitro measurements performed on a Pt/Ir concentric bipolar electrode in phosphate buffered saline (PBS) are presented. A statistical measurement over 40 channels from 5 different chips shows a current mismatch with μ = 1.12 μA and σ = 0.53 μA. The chip is integrated with flexible MEMS origami coils and parylene substrate to provide a fully intraocular implant.

Optimized single pulse stimulation strategy for retinal implants

Retinal implants offer prospects of vision restoration for some blind patients by eliciting visual percepts of spots of light called 'phosphenes'. Recently, a mathematical model has been developed that predicts patients' perception of phosphene brightness for current-driven electrical stimulation of the retina. This model is explored for different stimulation parameters on a single electrode, including safety and hardware limitations, to produce phosphenes of specified brightness. We describe a procedure to derive stimulation parameters to account for such constraints, and describe methods to construct optimal stimuli in terms of producing maximal perceived brightness and efficient generation of phosphenes of a given brightness by employing minimal energy. In both cases, it is found that the resulting optimized stimulation waveforms consist of a long stimulation period, and interphase delays between initial and charge-balancing phases.

Achievable peak electrode voltage reduction by neurostimulators using descending staircase currents to deliver charge

This paper considers the achievable reduction in peak voltage across two driving terminals of an RC circuit when delivering charge using a stepped current waveform, comprising a chosen number of steps of equal duration, compared with using a constant current over the total duration. This work has application to the design of neurostimulators giving reduced peak electrode voltage when delivering a given electric charge over a given time duration. Exact solutions for the greatest possible peak voltage reduction using two and three steps are given. Furthermore, it is shown that the achievable peak voltage reduction, for any given number of steps is identical for simple series RC circuits and parallel RC circuits, for appropriate different values of RC. It is conjectured that the maximum peak voltage reduction cannot be improved using a more complicated RC circuit.

In vivo validation of custom-designed silicon-based microelectrode arrays for long-term neural recording and stimulation

We developed and validated silicon-based neural probes for neural stimulating and recording in long-term implantation in the brain. The probes combine the deep reactive ion etching process and mechanical shaping of their tip region, yielding a mechanically sturdy shank with a sharpened tip to reduce insertion force into the brain and spinal cord, particularly, with multiple shanks in the same array. The arrays' insertion forces have been quantified in vitro. Five consecutive chronically-implanted devices were fully functional from 3 to 18 months. The microelectrode sites were electroplated with iridium oxide, and the charge injection capacity measurements were performed both in vitro and after implantation in the adult feline brain. The functionality of the chronic array was validated by stimulating in the cochlear nucleus and recording the evoked neuronal activity in the central nucleus of the inferior colliculus. The arrays' recording quality has also been quantified in vivo with neuronal spike activity recorded up to 566 days after implantation. Histopathology evaluation of neurons and astrocytes using immunohistochemical stains indicated minimal alterations of tissue architecture after chronic implantation.

Predicting phosphene elicitation in patients with retinal implants: a mathematical study

Single pulse waveforms were considered in a recent model for phosphene elicitation in patients with a retinal prosthesis. Waveforms are constrained to charge-balanced stimuli consisting of a single cathodic and anodic pulse pair. Mathematical models of such stimuli have been constructed and presented based upon patient testimonials. In this work, we derive analytic expressions that may be employed to determine equibrightness levels for different waveforms. We provide an example calculation to show quantitative improvements in stimulation efficiency that are consistent with qualitative findings on waveform effects.

Stimulus driver for epilepsy seizure suppression with adaptive loading impedance

A stimulus driver circuit for a micro-stimulator used in an implantable device is presented in this paper. For epileptic seizure control, the target of the driver was to output 30 µA stimulus currents when the electrode impedance varied between 20 and 200 kΩ. The driver, which consisted of the output stage, control block and adaptor, was integrated in a single chip. The averaged power consumption of the stimulus driver was 0.24-0.56 mW at 800 Hz stimulation rate. Fabricated in a 0.35 µm 3.3 V/24 V CMOS process and applied to a closed-loop epileptic seizure monitoring and controlling system, the proposed design has been successfully verified in the experimental results of Long-Evans rats with epileptic seizures.