1
|
Chen Y, Li D, Liu Z, Liu Y, Fan H, Hou S. Research progress of portable extracorporeal membrane oxygenation. Expert Rev Med Devices 2023; 20:221-232. [PMID: 36846940 DOI: 10.1080/17434440.2023.2185136] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 03/01/2023]
Abstract
INTRODUCTION Extracorporeal membrane oxygenation (ECMO) is primarily used for the supportive treatment of patients suffering from severe cardiopulmonary failure. With the continued development of ECMO technology, the relevant scenarios also extend pre-hospital and inter-hospital. In order to meet the needs of emergency treatment in communities, disaster sites and battlefields, inter-hospital transfer and evacuation; miniaturized and portable ECMO has become a current research hotspot. AREA COVERED The paper first introduces the principle, composition and common modes of ECMO and summarizes the research status of portable ECMO, Novalung and wearable ECMO, analyzes the characteristics and shortcomings of existing equipment. finally, we discussed the focus and development trend of portable ECMO technology. EXPERT OPINION Currently, portable ECMO has many applications in interhospital transport and there are various studies on portable and wearable ECMO devices, but the development of portable ECMO still faces many challenges. In the future, research related to integrated components, rich sensor arrays, Intelligent ECMO system and lightweight technology can make future portable ECMO more suitable for pre-hospital emergency and interhospital transport.
Collapse
Affiliation(s)
- Yuansen Chen
- Institute of Disaster and Emergency Medicine, Tianjin University, Tianjin, China.,Wenzhou Safety (Emergency) Institute, Tianjin University, Wenzhou, China
| | - Duo Li
- Institute of Disaster and Emergency Medicine, Tianjin University, Tianjin, China.,Wenzhou Safety (Emergency) Institute, Tianjin University, Wenzhou, China
| | - Ziquan Liu
- Institute of Disaster and Emergency Medicine, Tianjin University, Tianjin, China.,Wenzhou Safety (Emergency) Institute, Tianjin University, Wenzhou, China
| | - Yanqing Liu
- Institute of Disaster and Emergency Medicine, Tianjin University, Tianjin, China.,Wenzhou Safety (Emergency) Institute, Tianjin University, Wenzhou, China
| | - Haojun Fan
- Institute of Disaster and Emergency Medicine, Tianjin University, Tianjin, China.,Wenzhou Safety (Emergency) Institute, Tianjin University, Wenzhou, China
| | - Shike Hou
- Institute of Disaster and Emergency Medicine, Tianjin University, Tianjin, China.,Wenzhou Safety (Emergency) Institute, Tianjin University, Wenzhou, China
| |
Collapse
|
2
|
Syed A, Kerdi S, Qamar A. Bioengineering Progress in Lung Assist Devices. Bioengineering (Basel) 2021; 8:89. [PMID: 34203316 PMCID: PMC8301204 DOI: 10.3390/bioengineering8070089] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/09/2021] [Revised: 05/31/2021] [Accepted: 06/21/2021] [Indexed: 11/17/2022] Open
Abstract
Artificial lung technology is advancing at a startling rate raising hopes that it would better serve the needs of those requiring respiratory support. Whether to assist the healing of an injured lung, support patients to lung transplantation, or to entirely replace native lung function, safe and effective artificial lungs are sought. After 200 years of bioengineering progress, artificial lungs are closer than ever before to meet this demand which has risen exponentially due to the COVID-19 crisis. In this review, the critical advances in the historical development of artificial lungs are detailed. The current state of affairs regarding extracorporeal membrane oxygenation, intravascular lung assists, pump-less extracorporeal lung assists, total artificial lungs, and microfluidic oxygenators are outlined.
Collapse
Affiliation(s)
- Ahad Syed
- Nanofabrication Core Lab, King Abdullah University of Science and Technology, Thuwal 23955-6900, Saudi Arabia;
| | - Sarah Kerdi
- Biological and Environmental Science and Engineering Division, King Abdullah University of Science and Technology (KAUST), Thuwal 23955-6900, Saudi Arabia;
| | - Adnan Qamar
- Biological and Environmental Science and Engineering Division, King Abdullah University of Science and Technology (KAUST), Thuwal 23955-6900, Saudi Arabia;
| |
Collapse
|
3
|
Orizondo RA, Omecinski KS, May AG, Dhamotharan V, Frankowski BJ, Burgreen GW, Ye SH, Kocyildirim E, Sanchez PG, D’Cunha J, Wagner WR, Federspiel WJ. Month-long Respiratory Support by a Wearable Pumping Artificial Lung in an Ovine Model. Transplantation 2021; 105:999-1007. [PMID: 33031226 PMCID: PMC8024407 DOI: 10.1097/tp.0000000000003481] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/26/2022]
Abstract
BACKGROUND A wearable artificial lung could improve lung transplantation outcomes by easing implementation of physical rehabilitation during long-term pretransplant respiratory support. The Modular Extracorporeal Lung Assist System (ModELAS) is a compact pumping artificial lung currently under development. This study evaluated the long-term in vivo performance of the ModELAS during venovenous support in awake sheep. Feedback from early trials and computational fluid dynamic analysis guided device design optimization along the way. METHODS The ModELAS was connected to healthy sheep via a dual-lumen cannula in the jugular vein. Sheep were housed in a fixed-tether pen while wearing the device in a holster during support. Targeted blood flow rate and support duration were 2-2.5 L/min and 28-30 days, respectively. Anticoagulation was maintained via systemic heparin. Device pumping and gas exchange performance and hematologic indicators of sheep physiology were measured throughout support. RESULTS Computational fluid dynamic-guided design modifications successfully decreased pump thrombogenicity from initial designs. For the optimized design, 4 of 5 trials advancing past early perioperative and cannula-related complications lasted the full month of support. Blood flow rate and CO2 removal in these trials were 2.1 ± 0.3 L/min and 139 ± 15 mL/min, respectively, and were stable during support. One trial ended after 22 days of support due to intradevice thrombosis. Support was well tolerated by the sheep with no signs of hemolysis or device-related organ impairment. CONCLUSIONS These results demonstrate the ability of the ModELAS to provide safe month-long support without consistent deterioration of pumping or gas exchange capabilities.
Collapse
Affiliation(s)
- Ryan A. Orizondo
- McGowan Institute for Regenerative Medicine, University of Pittsburgh
- Department of Medicine, University of Pittsburgh
- Department of Bioengineering, University of Pittsburgh
| | - Katelin S. Omecinski
- McGowan Institute for Regenerative Medicine, University of Pittsburgh
- Department of Bioengineering, University of Pittsburgh
| | - Alexandra G. May
- McGowan Institute for Regenerative Medicine, University of Pittsburgh
- Department of Chemical and Petroleum Engineering, University of Pittsburgh
| | - Vishaal Dhamotharan
- McGowan Institute for Regenerative Medicine, University of Pittsburgh
- Department of Bioengineering, University of Pittsburgh
| | | | - Greg W. Burgreen
- Computational Fluid Dynamics Group, Center for Advanced Vehicular Systems, Mississippi State University
| | - Sang-Ho Ye
- McGowan Institute for Regenerative Medicine, University of Pittsburgh
- Department of Surgery, University of Pittsburgh
| | - Ergin Kocyildirim
- McGowan Institute for Regenerative Medicine, University of Pittsburgh
- Department of Cardiothoracic Surgery, Children’s Hospital of Pittsburgh
| | - Pablo G. Sanchez
- Department of Cardiothoracic Surgery, University of Pittsburgh Medical Center
| | - Jonathan D’Cunha
- Department of Cardiothoracic Surgery, University of Pittsburgh Medical Center
| | - William R. Wagner
- McGowan Institute for Regenerative Medicine, University of Pittsburgh
- Department of Bioengineering, University of Pittsburgh
- Department of Chemical and Petroleum Engineering, University of Pittsburgh
- Department of Surgery, University of Pittsburgh
| | - William J. Federspiel
- McGowan Institute for Regenerative Medicine, University of Pittsburgh
- Department of Bioengineering, University of Pittsburgh
- Department of Chemical and Petroleum Engineering, University of Pittsburgh
- Department of Critical Care Medicine, University of Pittsburgh Medical Center
- Clinical and Translational Science Institute, University of Pittsburgh
| |
Collapse
|
4
|
Hemocompatibility of new magnetically-levitated centrifugal pump technology compared to the CentriMag adult pump. Sci Rep 2020; 10:22055. [PMID: 33328596 PMCID: PMC7744571 DOI: 10.1038/s41598-020-78709-0] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/03/2019] [Accepted: 11/26/2020] [Indexed: 11/25/2022] Open
Abstract
The specific hemocompatibility properties of mechanical-circulatory-support (MCS)-pump technologies have not previously been described in a comparable manner. We thus investigated the hemocompatibility-indicating marker of a new magnetically-levitated (MagLev) centrifugal pump (MT-Mag) in a human, whole-blood mock-loop for 360 min using the MCS devices as a driving component. We compared those results with the CentriMag adult (C-Mag) device under the same conditions according to ISO10993-4. Blood samples were analyzed via enzyme-linked-immunosorbent-assay (ELISA) for markers of coagulation, complement system, and the inflammatory response. The time-dependent activation of the coagulation system was measured by detecting thrombin-anti-thrombin complexes (TAT). The activation of the complement system was determined by increased SC5b-9 levels in both groups. A significant activation of neutrophils (PMN-elastase) was detected within the C-Mag group, but not in the MT-Mag group. However, the amount of PMN-elastase at 360 min did not differ significantly between groups. The activation of the complement and coagulation system was found to be significantly time-dependent in both devices. However, coagulation activation as determined by the TAT level was lower in the MT-Mag group than in the C-Mag group. This slight disparity could have been achieved by the optimized secondary flow paths and surface coating, which reduces the interaction of the surface with blood.
Collapse
|
5
|
Swol J, Shigemura N, Ichiba S, Steinseifer U, Anraku M, Lorusso R. Artificial lungs--Where are we going with the lung replacement therapy? Artif Organs 2020; 44:1135-1149. [PMID: 33098217 DOI: 10.1111/aor.13801] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/26/2020] [Revised: 08/03/2020] [Accepted: 08/04/2020] [Indexed: 12/12/2022]
Abstract
Lung transplantation may be a final destination therapy in lung failure, but limited donor organ availability creates a need for alternative management, including artificial lung technology. This invited review discusses ongoing developments and future research pathways for respiratory assist devices and tissue engineering to treat advanced and refractory lung disease. An overview is also given on the aftermath of the coronavirus disease 2019 pandemic and lessons learned as the world comes out of this situation. The first order of business in the future of lung support is solving the problems with existing mechanical devices. Interestingly, challenges identified during the early days of development persist today. These challenges include device-related infection, bleeding, thrombosis, cost, and patient quality of life. The main approaches of the future directions are to repair, restore, replace, or regenerate the lungs. Engineering improvements to hollow fiber membrane gas exchangers are enabling longer term wearable systems and can be used to bridge lung failure patients to transplantation. Progress in the development of microchannel-based devices has provided the concept of biomimetic devices that may even enable intracorporeal implantation. Tissue engineering and cell-based technologies have provided the concept of bioartificial lungs with properties similar to the native organ. Recent progress in artificial lung technologies includes continued advances in both engineering and biology. The final goal is to achieve a truly implantable and durable artificial lung that is applicable to destination therapy.
Collapse
Affiliation(s)
- Justyna Swol
- Department of Respiratory Medicine, Allergology and Sleep Medicine, Intensive Care Medicine, Paracelsus Medical University Nuremberg, General Hospital Nuremberg, Nuremberg, Germany
| | - Norihisa Shigemura
- Division of Cardiovascular Surgery, Temple University Health System Inc., Philadelphia, PA, USA
| | - Shingo Ichiba
- Department of Surgical Intensive Care Medicine, Nippon Medical School Hospital, Bunkyo-ku, Japan
| | - Ulrich Steinseifer
- Department of Cardiovascular Engineering, Institute of Applied Medical Engineering, Aachen, Germany
| | - Masaki Anraku
- Department of Thoracic Surgery, The University of Tokyo Graduate School of Medicine Faculty of Medicine, Bunkyo-ku, Japan
| | - Roberto Lorusso
- Cardio-Thoracic Surgery Department - Heart & Vascular Centre, Maastricht University Medical Hospital, Maastricht, The Netherlands
| |
Collapse
|
6
|
New Approaches to Respiratory Assist: Bioengineering an Ambulatory, Miniaturized Bioartificial Lung. ASAIO J 2020; 65:422-429. [PMID: 30044238 DOI: 10.1097/mat.0000000000000841] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/25/2022] Open
Abstract
Although state-of-the-art treatments of respiratory failure clearly have made some progress in terms of survival in patients suffering from severe respiratory system disorders, such as acute respiratory distress syndrome (ARDS), they failed to significantly improve the quality of life in patients with acute or chronic lung failure, including severe acute exacerbations of chronic obstructive pulmonary disease or ARDS as well. Limitations of standard treatment modalities, which largely rely on conventional mechanical ventilation, emphasize the urgent, unmet clinical need for developing novel (bio)artificial respiratory assist devices that provide extracorporeal gas exchange with a focus on direct extracorporeal CO2 removal from the blood. In this review, we discuss some of the novel concepts and critical prerequisites for such respiratory lung assist devices that can be used with an adequate safety profile, in the intensive care setting, as well as for long-term domiciliary therapy in patients with chronic ventilatory failure. Specifically, we describe some of the pivotal steps, such as device miniaturization, passivation of the blood-contacting surfaces by chemical surface modifications, or endothelial cell seeding, all of which are required for converting current lung assist devices into ambulatory lung assist device for long-term use in critically ill patients. Finally, we also discuss some of the risks and challenges for the long-term use of ambulatory miniaturized bioartificial lungs.
Collapse
|
7
|
An In Vitro Blood Flow Loop System for Evaluating the Thrombogenicity of Medical Devices and Biomaterials. ASAIO J 2020; 66:183-189. [PMID: 30807378 PMCID: PMC10370649 DOI: 10.1097/mat.0000000000000958] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/15/2022] Open
Abstract
A reliable in vitro dynamic test method to evaluate device thrombogenicity is very important for the improvement of the design and safety of blood-contacting medical devices, while reducing the use of animal studies. In this study, a recirculating flow loop system was developed for thrombogenicity testing, using donor sheep blood anticoagulated with Anticoagulant Citrate Dextrose Solution A (ACDA) and used within 24-36 hr postdraw. Immediately before testing, the blood was recalcified and heparinized to a donor-specific target concentration. The heparinization level was based on a static pretest, in which latex tubes were incubated at room temperature for 30 min in blood with a series of heparin concentrations and evaluated for thrombus deposition. For dynamic testing, blood was recirculated at room temperature through a polyvinyl chloride (PVC) tubing loop containing a test material for 1 hr at 200 ml/min using a roller pump. Nine materials were investigated: a negative control (polytetrafluoroethylene [PTFE]), a positive control (latex), and seven commonly used biomaterials including PVC, two silicones with different formulations (Q-Sil and V-Sil), nylon, polyurethane (PU), high-density polyethylene (HDPE), and polyether block amide (PEBAX). The results showed that latex was significantly more thrombogenic than all the other materials (p < 0.05), PVC and Q-Sil exhibited intermediate thrombogenicity with significantly more thrombus surface coverage and thrombus weight than PTFE (p < 0.05), whereas PTFE and the rest of the biomaterials had little to no thrombus deposition. In summary, the test loop system was able to effectively differentiate materials with different thrombogenic potentials.
Collapse
|
8
|
|
9
|
Abstract
One in five children with end-stage lung failure (ESLF) die while awaiting lung transplant. No suitable animal model of ESLF exists for the development of artificial lung devices for bridging to transplant. Small lambs weighing 15.7 ± 3.1 kg (n = 5) underwent ligation of the left anterior pulmonary artery (PA) branch, and gradual occlusion of the right main PA over 48 hours. All animals remained hemodynamically stable. Over seven days of disease model conditions, they developed pulmonary hypertension (mean PA pressure 20 ± 5 vs. 33 ± 4 mm Hg), decreased perfusion (SvO2 66 ± 3 vs. 55 ± 8%) with supplemental oxygen requirement, and severe tachypneic response (45 ± 9 vs. 82 ± 23 breaths/min) (all p < 0.05). Severe right heart dysfunction developed (tricuspid annular plane systolic excursion 13 ± 3 vs. 7 ± 2 mm, fractional area change 36 ± 6 vs. 22 ± 10 mm, ejection fraction 51 ± 9 vs. 27 ± 17%, all p < 0.05) with severe tricuspid regurgitation and balloon-shaped dilation of the right ventricle. This model of pediatric ESLF reliably produces pulmonary hypertension, right heart strain, and impaired gas exchange, and will be used to develop a pediatric artificial lung.
Collapse
|
10
|
Rajagopal K, Hoeper MM. State of the Art: Bridging to lung transplantation using artificial organ support technologies. J Heart Lung Transplant 2016; 35:1385-1398. [PMID: 27916175 DOI: 10.1016/j.healun.2016.10.005] [Citation(s) in RCA: 24] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/02/2016] [Revised: 10/05/2016] [Accepted: 10/12/2016] [Indexed: 11/29/2022] Open
Abstract
Lung transplantation increasingly is being performed in recipients of higher risk and acuity. A subset of these patients has severely abnormal gas exchange and/or right ventricular dysfunction, such that artificial organ support strategies are required to bridge patients to lung transplantation. We review the rationales and currently used and potential strategies for bridging to lung transplantation and characterize bridging outcomes. Based on physiologic reasoning and a study of the existing literature, we provide a working strategy for bridging to lung transplantation.
Collapse
Affiliation(s)
- Keshava Rajagopal
- Center for Advanced Heart Failure and Department of Cardiothoracic/Vascular Surgery, University of Texas-Houston and Memorial Hermann-Texas Medical Center, Houston, Texas.
| | - Marius M Hoeper
- Department of Respiratory Medicine, Hannover Medical School, and German Center for Lung Research (DZL), Hannover, Germany
| |
Collapse
|
11
|
Pilarczyk K, Heckmann J, Lyskawa K, Strauß A, Haake N, Wiese I, Jakob H, Kamler M, Pizanis N. Comparison of a New Miniaturized Extracorporeal Membrane Oxygenation System With Integrated Rotary Blood Pump to a Standard System in a Porcine Model of Acute Lung Injury. Artif Organs 2015; 40:645-58. [PMID: 26636760 DOI: 10.1111/aor.12611] [Citation(s) in RCA: 4] [Impact Index Per Article: 0.4] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/03/2023]
Abstract
Extracorporeal membrane oxygenation (ECMO) is used for severe acute respiratory distress syndrome. However, available ECMO systems are large and not well designed for fast delivery, emergency implantation, and interhospital transfer. Therefore, a new miniaturized oxygenator with integrated rotary blood pump (ILIAS) was developed and compared with a standard ECMO system in a large animal model. Acute lung injury was induced with repeated pulmonary saline lavage in 14 pigs until PaO2 /FiO2 -ratio was <100 mm Hg with a positive-end-expiratory-pressure of 5 mbar. Pigs were assigned to the following three groups: group 1 (n = 4): control group with conventional ventilation; group 2 (n = 5): standard vv-ECMO; group 3 (n = 5): vv-ILIAS. Gas exchange, hemodynamics, hemolysis, and coagulation activation were examined over a period of 8 h. No device failed during the observation period. PaCO2 decreased from 59.40 ± 4.14 mm Hg to 48.62 ± 4.50 mm Hg after 1 h in the ILIAS group compared with an improvement of PaCO2 from 48.86 ± 7.45 to 40.10 ± 6.02 in the conventional ECMO group (P = not significant [n.s.]). ARDS-induced respiratory acidosis was controlled promptly with a pH of 7.2 ± 0.1 at baseline increasing to 7.4 ± 0.1 in both study groups after 60 min of ECMO support. Mean carbon dioxide transfer was comparable between the conventional ECMO and ILIAS (211.36 ± 78.39 mL/min vs. 219.99 ± 76.72 mL/min, P = n.s.). PaO2 /FiO2 increased from 118.4 ± 15.5 mm Hg to 179.1 ± 72.4 mm Hg in the ILIAS group compared with an improvement of oxygenation from 107.1 ± 24.9 mm Hg to 179.0 ± 45.7 mm Hg in the standard ECMO group (P = n.s.). Mean oxygen transfer was calculated with 136.09 ± 30.25 mL/min for the ILIAS and 129.05 ± 36.28 mL/min for the standard ECMO. Hemodynamic instability or significant activation of the plasmatic coagulation was not observed. However, hemolysis was significantly higher in the ILIAS group compared with the conventional ECMO. As the ILIAS prototype provided excellent gas exchange with hemodynamic stability comparable with a standard ECMO system, we believe this study serves as a proof of concept. Further development and design modifications (optimized rotation speed and surface coating of rotor) are already done and another experiment is projected to reduce hemolysis and platelet consumption for clinical application.
Collapse
Affiliation(s)
- Kevin Pilarczyk
- Department of Thoracic and Cardiovascular Surgery, West German Heart and Vascular Center Essen, University Hospital Essen, Essen, Germany
| | - Jens Heckmann
- Department of Thoracic and Cardiovascular Surgery, West German Heart and Vascular Center Essen, University Hospital Essen, Essen, Germany
| | - Kathrin Lyskawa
- Department of Thoracic and Cardiovascular Surgery, West German Heart and Vascular Center Essen, University Hospital Essen, Essen, Germany
| | - Andreas Strauß
- Andreas Strauß Medizintechnik, Technology Center Ruhr, Bochum, Germany
| | - Nils Haake
- Department of Cardiovascular Surgery, University of Schleswig-Holstein, Kiel, Germany
| | - Ingo Wiese
- Department of Thoracic and Cardiovascular Surgery, West German Heart and Vascular Center Essen, University Hospital Essen, Essen, Germany
| | - Heinz Jakob
- Department of Thoracic and Cardiovascular Surgery, West German Heart and Vascular Center Essen, University Hospital Essen, Essen, Germany
| | - Markus Kamler
- Department of Thoracic and Cardiovascular Surgery, West German Heart and Vascular Center Essen, University Hospital Essen, Essen, Germany
| | - Nikolaus Pizanis
- Department of Thoracic and Cardiovascular Surgery, West German Heart and Vascular Center Essen, University Hospital Essen, Essen, Germany
| |
Collapse
|
12
|
Schibilsky D, Lenglinger M, Avci-Adali M, Haller C, Walker T, Wendel HP, Schlensak C. Hemocompatibility of Axial Versus Centrifugal Pump Technology in Mechanical Circulatory Support Devices. Artif Organs 2015; 39:723-8. [DOI: 10.1111/aor.12544] [Citation(s) in RCA: 10] [Impact Index Per Article: 1.1] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/30/2023]
Affiliation(s)
- David Schibilsky
- Department of Thoracic and Cardiovascular Surgery; University Medical Center Tuebingen; Tübingen Germany
| | - Matthias Lenglinger
- Department of Thoracic and Cardiovascular Surgery; University Medical Center Tuebingen; Tübingen Germany
| | - Meltem Avci-Adali
- Department of Thoracic and Cardiovascular Surgery; University Medical Center Tuebingen; Tübingen Germany
| | - Christoph Haller
- Department of Thoracic and Cardiovascular Surgery; University Medical Center Tuebingen; Tübingen Germany
| | - Tobias Walker
- Department of Thoracic and Cardiovascular Surgery; University Medical Center Tuebingen; Tübingen Germany
| | - Hans Peter Wendel
- Department of Thoracic and Cardiovascular Surgery; University Medical Center Tuebingen; Tübingen Germany
| | - Christian Schlensak
- Department of Thoracic and Cardiovascular Surgery; University Medical Center Tuebingen; Tübingen Germany
| |
Collapse
|
13
|
Ding J, Chen Z, Niu S, Zhang J, Mondal NK, Griffith BP, Wu ZJ. Quantification of Shear-Induced Platelet Activation: High Shear Stresses for Short Exposure Time. Artif Organs 2015; 39:576-83. [PMID: 25808300 DOI: 10.1111/aor.12438] [Citation(s) in RCA: 46] [Impact Index Per Article: 5.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/26/2023]
Abstract
Thrombosis and thromboembolism are the life-threatening clinical complications for patients supported or treated with prosthetic cardiovascular devices. The high mechanical shear stress within these devices is believed to be the major contributing factor to cause platelet activation (PA) and function alteration, leading to thrombotic events. There have been limited quantitative data on how the high mechanical shear stress causes platelet activation. In this study, shear-induced PA in the ranges of well-defined shear stress and exposure time relevant to cardiovascular devices was quantitatively characterized for human blood using two novel flow-through Couette-type blood shearing devices. Four markers of platelet activation-surface P-selectin (CD62p), platelet-derived microparticles (PMPs), platelet-monocyte aggregation (PMA), and soluble P-selectin-were measured by flow cytometry and enzyme-linked immunosorbent assay (ELISA), respectively. The results indicated that PA induced by high shear stresses with short exposure time could be reliably detected with surface P-selectin, and, to a lesser extent, PMPs rather than soluble P-selectin. It was also verified that PMA can be a highly sensitive indirect marker of platelet activation. The quantitative relationship between percentage of activated platelets indicated by surface P-selectin expression and shear stress/exposure time follows well the power law functional form. The coefficients of the power law models of PA based on surface P-selectin expression were derived.
Collapse
Affiliation(s)
- Jun Ding
- Artificial Organs Laboratory, Department of Surgery, University of Maryland School of Medicine, Baltimore, MD, USA.,Department of Mechanical Engineering, University of Maryland, Baltimore County, Baltimore, MD, USA
| | - Zengsheng Chen
- Artificial Organs Laboratory, Department of Surgery, University of Maryland School of Medicine, Baltimore, MD, USA
| | - Shuqiong Niu
- Artificial Organs Laboratory, Department of Surgery, University of Maryland School of Medicine, Baltimore, MD, USA
| | - Jiafeng Zhang
- Artificial Organs Laboratory, Department of Surgery, University of Maryland School of Medicine, Baltimore, MD, USA
| | - Nandan K Mondal
- Artificial Organs Laboratory, Department of Surgery, University of Maryland School of Medicine, Baltimore, MD, USA
| | - Bartley P Griffith
- Artificial Organs Laboratory, Department of Surgery, University of Maryland School of Medicine, Baltimore, MD, USA
| | - Zhongjun J Wu
- Artificial Organs Laboratory, Department of Surgery, University of Maryland School of Medicine, Baltimore, MD, USA
| |
Collapse
|
14
|
Almeida D, Barletta M, Mathews L, Graham L, Quandt J. Comparison between invasive blood pressure and a non-invasive blood pressure monitor in anesthetized sheep. Res Vet Sci 2014; 97:582-6. [DOI: 10.1016/j.rvsc.2014.10.004] [Citation(s) in RCA: 7] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/06/2014] [Revised: 07/24/2014] [Accepted: 10/05/2014] [Indexed: 10/24/2022]
|
15
|
Abstract
In this Editor's Review, articles published in 2013 are organized by category and briefly summarized. We aim to provide a brief reflection of the currently available worldwide knowledge that is intended to advance and better human life while providing insight for continued application of technologies and methods of organ Replacement, Recovery, and Regeneration. As the official journal of The International Federation for Artificial Organs, The International Faculty for Artificial Organs, the International Society for Rotary Blood Pumps, the International Society for Pediatric Mechanical Cardiopulmonary Support, and the Vienna International Workshop on Functional Electrical Stimulation, Artificial Organs continues in the original mission of its founders "to foster communications in the field of artificial organs on an international level". Artificial Organs continues to publish developments and clinical applications of artificial organ technologies in this broad and expanding field of organ Replacement, Recovery, and Regeneration from all over the world. We take this time also to express our gratitude to our authors for offering their work to this journal. We offer our very special thanks to our reviewers who give so generously of time and expertise to review, critique, and especially provide so meaningful suggestions to the author's work whether eventually accepted or rejected and especially to those whose native tongue is not English. Without these excellent and dedicated reviewers the quality expected from such a journal could not be possible. We also express our special thanks to our Publisher, Wiley Periodicals, for their expert attention and support in the production and marketing of Artificial Organs. We look forward to recording further advances in the coming years.
Collapse
|
16
|
Mertz L. Biocompatible Medical Devices: Raise the Bar for Health Care. IEEE Pulse 2013; 4:16-20. [DOI: 10.1109/mpul.2013.2262139] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/10/2022]
|