Investigation of the Axial Gap Clearance in a Hydrodynamic-Passive Magnetically Levitated Rotary Blood Pump Using X-Ray Radiography

The Impact of Rotor Axial Displacement Variation on Simulation Accuracy of Fully Magnetic Levitation Centrifugal Blood Pump

The rotor axial displacement of the full magnetic levitation blood pump varies with the operating conditions. The effect of rotor axial displacement on simulation results is unclear. This study aimed to evaluate the effect of rotor axial displacement on the predicted blood pump flow field, hydraulic performance, and hemocompatibility through simulation. This study used the CentriMag blood pump as a model, and conducted computational fluid dynamics simulations to assess the impact of rotor displacement. Considering rotor axial displacement leads to opposite results regarding predicted residence time and thrombotic risk compared with not considering rotor axial displacement. Not considering rotor axial displacement leads to deviations in the predicted values, where the effects on the flow field within the blood pump, ratio of secondary flow, and amount of shear stress >150 Pa are significant. The variation in the back clearance of the blood pump caused by the ideal and actual rotor displacements is the main cause of the above phenomena. Given that the rotor axial displacement significantly impacts the simulation accuracy, the effect of rotor axial displacement must be considered in the simulation.

The Future of Durable Mechanical Circulatory Support: Emerging Technological Innovations and Considerations to Enable Evolution of the Field

The field of durable mechanical circulatory support (MCS) has undergone an incredible evolution over the past few decades, resulting in significant improvements in longevity and quality of life for patients with advanced heart failure. Despite these successes, substantial opportunities for further improvements remain, including in pump design and ancillary technology, perioperative and postoperative management, and the overall patient experience. Ideally, durable MCS devices would be fully implantable, automatically controlled, and minimize the need for anticoagulation. Reliable and long-term total artificial hearts for biventricular support would be available; and surgical, perioperative, and postoperative management would be informed by the individual patient phenotype along with computational simulations. In this review, we summarize emerging technological innovations in these areas, focusing primarily on innovations in late preclinical or early clinical phases of study. We highlight important considerations that the MCS community of clinicians, engineers, industry partners, and venture capital investors should consider to sustain the evolution of the field.

Effect of Particle Migration on the Stress Field in Microfluidic Flows of Blood Analog Fluids at High Reynolds Numbers

In the present paper, we investigate how the reductions in shear stresses and pressure losses in microfluidic gaps are directly linked to the local characteristics of cell-free layers (CFLs) at channel Reynolds numbers relevant to ventricular assist device (VAD) applications. For this, detailed studies of local particle distributions of a particulate blood analog fluid are combined with wall shear stress and pressure loss measurements in two complementary set-ups with identical flow geometry, bulk Reynolds numbers and particle Reynolds numbers. For all investigated particle volume fractions of up to 5%, reductions in the stress and pressure loss were measured in comparison to a flow of an equivalent homogeneous fluid (without particles). We could explain this due to the formation of a CFL ranging from 10 to 20 μm. Variations in the channel Reynolds number between Re = 50 and 150 did not lead to measurable changes in CFL heights or stress reductions for all investigated particle volume fractions. These measurements were used to describe the complete chain of how CFL formation leads to a stress reduction, which reduces the apparent viscosity of the suspension and results in the Fåhræus-Lindqvist effect. This chain of causes was investigated for the first time for flows with high Reynolds numbers (Re∼100), representing a flow regime which can be found in the narrow gaps of a VAD.

The impact of rotor configurations on hemodynamic features, hemocompatibility and dynamic balance of the centrifugal blood pump: A numerical study

To investigate the effect of rotor design configuration on hemodynamic features, hemocompatibility and dynamic balance of blood pumps. Computational fluid dynamics was employed to investigate the effects of rotor type (closed impeller, semi-open impeller), clearance height and back vanes on blood pump performance. In particular, the Eulerian hemolysis model based on a power-law function and the Lagrangian thrombus model with integrated stress accumulation and residence time were applied to evaluate the hemocompatibility of the blood pump. This study shows that compared to the closed impeller, the semi-open impeller can improve hemolysis at a slight sacrifice in head pressure, but increase the risk of thrombogenic potential and disrupt rotor dynamic balance. For the semi-open impeller, the pressure head, hemolysis, and axial thrust of the blood pump decrease with increasing front clearance, and the risk of thrombosis increases first and then decreases with increasing front clearance. Variations in back clearance have little effect on pressure head, but larger on back clearance, worsens hemolysis, thrombogenic potential and rotor dynamic balance. The employment of back vanes has little effect on the pressure head. All back vanes configurations have an increased risk of hemolysis in the blood pump but are beneficial for the improvement of the rotor dynamic balance of the blood pump. Reasonable back vanes configuration (higher height, wider width, longer length and more number) decreases the flow separation, increases the velocity of blood in the back clearance, and reduces the risk of blood pooling and thrombosis. It was also found that hemolysis index (HI) was highly negatively correlated with pressure difference between the top and back clearances (r = -.87), and thrombogenic potential was positively correlated with pressure difference between the top and back clearances (r = .71). This study found that rotor type, clearance height, and back vanes significantly affect the hydraulic performance, hemocompatibility and rotor dynamic balance of centrifugal blood pumps through secondary flow. These parameters should be carefully selected when designing and optimizing centrifugal blood pumps for improving the blood pump clinical outcomes.

Numerical study on the performance of centrifugal blood pump with superhydrophobic surface

AIM

In order to reduce the blood damage of an artificial heart pump and optimize its hydraulic performance, a centrifugal blood pump with superhydrophobic characteristics is proposed in this study.

METHODS

To study the influence of superhydrophobic surface characteristics on the performance of centrifugal blood pumps, the Navier slip model is used to simulate the slip characteristics of superhydrophobic surfaces, which is realized by the user defined function of ANSYS fluent. The user defined functions with different values of slip length are verified by two benchmark solutions of laminar flow and turbulence in the pipeline. The blood pump model adopts the designed centrifugal blood pump, and its head, hydraulic efficiency and hemolysis index are calculated. The Navier slip boundary condition (a constant slip-length of 50 μm) is applied to the walls of the blood pump impeller and a volute at different positions, and the influence of the superhydrophobic surface on the performance of the blood pump at the design point Q = 6 L/min was compared and analyzed.

RESULTS

The results show that the centrifugal blood pump model used in this paper has good blood compatibility and meets the design requirements; the superhydrophobic surface can significantly reduce the scalar shear stress in the blood pump. At the design point, when the slip length is 50 μm, the mass-average scalar shear stress in the impeller area and the volute area reduction rate is about 5.9%, the hydraulic efficiency growth rate is about 3.8%, the hemolysis index reduction rate is about 18.4%, and the pressure head changes little with a growth rate of 0.3%.

CONCLUSIONS

Centrifugal blood pumps with superhydrophobic surfaces can improve the efficiency of blood pumps and reduce hemolysis. Based on these encouraging results, vitro investigations for actual blood damage would be practicable.

Hemodynamic investigation and in vitro evaluation of a novel mixed flow blood pump

INTRODUCTION

Ventricular assist devices (VADs) are considered as an effective treatment for patients with advanced heart failure, while complications associated with blood damage remain a burden. Structure design innovation has potential to reduce hemolysis and improve hemocompatibility.

METHODS

In this research, a novel mixed flow blood pump that integrates structural features of the axial and centrifugal VADs was proposed. The pump consists of an inducer, a mixed impeller supported by two ceramic pivot bearings and a volute. The flow field and laminar viscous shear stress were analyzed by the in-silico simulation. The hydraulic and hemolytic performance were evaluated in vitro by using a 3D printed pump.

RESULTS

The flow field distribution showed that streamlines in the connection area were smoothly transitioned through structural integration and no irregular flow occurred in the entire flow channel. The axial blades work as a fluid accelerator (generating 18.56% of the energy), and the centrifugal blades provide the main pressure head. The proportion of fluid inside the pump exposed to low laminar viscous shear stress (<50 Pa) and high laminar viscous shear stress (>150 Pa) was 99.02% and 0.03%, respectively. The in vitro hemolysis test results showed that the NIH (Normalized Index of Hemolysis) value of the mixed pump is 0.0079 ± 0.0039 g/100 L (n=6).

CONCLUSION

It can be concluded that the mixed flow structure is effective to improve hydraulic performance, eliminate flow disturbance and minimize shear stresses. This novel pump design is expected to provide a new direction for the development of next-generation VADs.

Hemolytic Footprint of Rotodynamic Blood Pumps

OBJECTIVE

In preclinical examinations, rotodynamic blood pumps (RBPs) are predominantly evaluated at design-point conditions. In clinical practice, however, they run at diversified modes of operation. This study aimed at extending current preclinical evaluation of hemolytic profiles in RBPs toward broader, clinically relevant ranges of operation.

METHODS

Two implantable RBPs the HeartMate 3 (HM3) and the HeartWare Ventricular Assist Device (HVAD) were analyzed at three pump speeds (HM3: 4300, 5600, 7000rpm; HVAD: 1800, 2760, 3600rpm) with three flow rates (1-9L/min) per speed setting. Hemolysis measurements were performed in heparinized bovine blood. The delta free hemoglobin (dfHb) and the normalized index of hemolysis (NIH) served as hemolytic measures. Statistical analysis was performed by multiple comparison of the 9 operating conditions. Moreover, computational fluid dynamics (CFD) was applied to provide mechanistic insights into the interrelation between hydraulics and hemolysis by correlating numerically computed hydraulic losses with in-vitro hemolytic measures.

RESULTS

In both devices, dfHb increased toward increasing speeds, particularly during low but also during high flow condition. By contrast, in both RBPs magnitudes of NIH were significantly elevated during low flow operation compared to high flow conditions (p<0.0036). Maps of hemolytic metrics revealed morphologically similar trends to in-silico hydraulic losses (r>0.793).

CONCLUSIONS

While off-design operation is associated with increased hemolytic profiles, the setting of different operating conditions render a preclinical prediction of clinical impact with current hemolysis metrics difficult.

SIGNIFICANCE

The identified increase in hemolytic measures during episodes of off-design operation is highlighting the need to consider worst-case operation during preclinical examinations.

Heuristic optimization of impeller sidewall gaps-based on the bees algorithm for a centrifugal blood pump by CFD

Optimization studies on blood pumps that require complex designs are gradually increasing in number. The essential design criteria of centrifugal blood pump are minimum shear stress with maximal efficiency. The geometry design of impeller sidewall gaps (blade tip clearance, axial gap, radial gap) is highly effective with regard to these two criteria. Therefore, unlike methods such as trial and error, the optimal dimensions of these gaps should be adjusted via a heuristic method, giving more effective results. In this study, the optimal gaps that can ensure these two design criteria with The Bees Algorithm (BA), which is a population-based heuristic method, are investigated. Firstly, a Computational Fluid Dynamics (CFD) analysis of sample pump models, which are selected according to the orthogonal array and pre-designed with different gaps, are performed. The dimensions of the gaps are optimized through this mathematical model. The simulation results for the improved pump model are nearly identical to those predicted by the BA. The improved pump model, as designed with the optimal gap dimensions so obtained, is able to meet the design criteria better than all existing sample pumps. Thanks to the optimal gap dimensions, it has been observed that compared to average values, it has provided a 42% reduction in aWSS and a 20% increase in efficiency. Moreover, original an approach to the design of impeller sidewall gaps was developed. The results show that computational costs have been significantly reduced by using the BA in blood pump geometry design.

Thrombotic Risk of Rotor Speed Modulation Regimes of Contemporary Centrifugal Continuous-flow Left Ventricular Assist Devices

Contemporary centrifugal continuous-flow left ventricular assist devices (LVADs) incorporate dynamic speed modulation algorithms. Hemocompatibility of these periodic unsteady pump operating conditions has been only partially explored. We evaluated whether speed modulation induces flow alterations associated with detrimental prothrombotic effects. For this aim, we evaluated the thrombogenic profile of the HeartWare ventricular assist device (HVAD) Lavare Cycle (LC) and HeartMate3 (HM3) artificial pulse (AP) via comprehensive numerical evaluation of (i) pump washout, (ii) stagnation zones, (iii) shear stress regimens, and (iv) modeling of platelet activation status via the platelet activity state (PAS) model. Data were compared between different simulated operating scenarios, including: (i) constant rotational speed and pump pressure head, used as reference; (ii) unsteady pump pressure head as induced by cardiac pulsatility; and (iii) unsteady rotor speed modulation of the LC (HVAD) and AP (HM3). Our results show that pump washout did not improve across the different simulated scenarios in neither the HVAD nor the HM3. The LC reduced but did not eliminate flow stagnation (-57%) and did not impact metrics of HVAD platelet activation (median PAS: +0.4%). The AP reduced HM3 flow stagnation by up to 91% but increased prothrombotic shear stress and simulated platelet activation (median PAS: +124%). Our study advances understanding of the pathogenesis of LVAD thrombosis, suggesting mechanistic implications of rotor speed modulation. Our data provide rationale criteria for the future design optimization of next generation LVADs to further reduce hemocompatibility-related adverse events.

Effect of the Center Post Establishment and Its Design Variations on the Performance of a Centrifugal Rotary Blood Pump

PURPOSE

The main purpose is to compare the characteristics and performance of a centrifugal blood pump with and without center post. Furthermore, to propose a center post design guide for the development of centrifugal blood pumps: finding the appropriate height and diameter of the center post.

METHODS

A centrifugal blood pump with different center post configurations is investigated using Computational Fluid Dynamics (CFD) in an extensive parametric approach. Height and diameter of the center post are varied on 4 levels each. Pressure head and hydraulic efficiency curves, pressure and velocity contours and volumetric histograms of scalar shear stress (SSS) distribution are discussed in detail.

RESULTS

The simulation results show uniform pressure distribution around the casing in the baseline design. Although obtaining the minimum Normalized Index of Hemolysis (NIH), average scalar shear stress (ASSS), and volumetric percentage ratios (SSS > 9, 50 and 150 Pa), a stagnation and recirculation zone in the impeller eye above the casing bottom is detected in center post free (H = 0 mm) pump. With the establishment and further increase of the center post height, the stagnation zone disappears gradually. The results also indicate that flow recirculation and stagnation around the circumference of the center post occurs when the center post has a small diameter. As the diameter increases, a reversed flow is formed between the impeller and the center post.

CONCLUSIONS

The center post can greatly reduce the stagnation zone occurring in the center post free pump. The diameter of center post makes a difference to the flow field in the gap between the impeller and the center post.

Impeller (straight blade) design variations and their influence on the performance of a centrifugal blood pump

INTRODUCTION

The miniaturization of blood pumps has become a trend due to the advantage of easier transplantation, especially for pediatric patients. In small-scale pumps, it is much easier and more cost-efficient to manufacture the impeller with straight blades compared to spiral-profile blades.

METHODS

Straight-blade impeller designs with different blade angles, blade numbers, and impeller flow passage positions are evaluated using the computational fluid dynamics method. Blade angles (θ = 0°, 20°, 30°, and 40°), blade numbers (N = 5, 6, 7, and 8), and three positions of impeller flow passage (referred to as top, middle, and bottom) are selected as the studied parametric values.

RESULTS

The numerical results reveal that with increasing blade angle, the pressure head and the hydraulic efficiency increase, and the average scalar shear stress and the normalized index of hemolysis decrease. The minimum radial force and axial thrust are obtained when θ equals 20°. In addition, the minimum average scalar shear stress and normalized index of hemolysis values are obtained when N = 6, and the maximum values are obtained when N = 5. Regarding the impeller flow passage position, the axial thrust and the stagnation area forming in the impeller eye are reduced as the flow passage height declines.

CONCLUSION

The consideration of a blade angle can greatly improve the performance of blood pumps, although the influence of the blade number is not very easily determined. The bottom position of the impeller flow passage is the best design.

Computational characterization of flow and blood damage potential of the new maglev CH-VAD pump versus the HVAD and HeartMate II pumps

Left ventricular assist devices are routinely used to treat patients with advanced heart failure as a bridge to transplant or a destination therapy. However, non-physiological shear stress generated by left ventricular assist devices damages blood cells. The continued development of novel left ventricular assist devices is essential to improve the left ventricular assist device therapy for heart failure patients. The CH-VAD is a new maglev centrifugal left ventricular assist device. In this study, the CH-VAD pump was numerically analyzed and compared with the HVAD and HeartMate II pumps under two clinically relevant conditions (flow: 4.5 L/min, pressure head: normal ~80 and hypertension ~120 mmHg). The velocity and shear stress fields, washout, and hemolysis index of the three pumps were assessed with computational fluid dynamics analysis. Under the same condition, the CH-VAD hemolysis index was two times lower than the HVAD and HeartMate II pumps; the CH-VAD had the least percentage volume with shear stress larger than 100 Pa (i.e. normal condition: 0.4% vs HVAD 1.0%, and HeartMate II 2.9%). Under the normal condition, more than 98% was washed out of the three pumps within 0.4 s. The washout times were slightly shorter under the hypertension condition for the three pumps. No regions inside the CH-VAD or HVAD had extremely long residential time, while areas near the straightener of the HeartMate II pump had long residential time (>4 s) indicating elevated risks of thrombosis. The computational fluid dynamics results suggested that the CH-VAD pump has a better hemolytic biocompatibility than the HVAD and HeartMate II pumps under the normal and hypertension conditions.

Artificial Organs 2018: A Year in Review

In this Editor's Review, articles published in 2018 are organized by category and summarized. We provide a brief reflection of the research and progress in artificial organs intended to advance and better human life while providing insight for continued application of these technologies and methods. Artificial Organs continues in the original mission of its founders "to foster communications in the field of artificial organs on an international level." Artificial Organs continues to publish developments and clinical applications of artificial organ technologies in this broad and expanding field of organ Replacement, Recovery, and Regeneration from all over the world. Peer-reviewed special issues this year included contributions from the 13th International Conference on Pediatric Mechanical Circulatory Support Systems and Pediatric Cardiopulmonary Perfusion edited by Dr. Akif Undar, and the 25th Congress of the International Society for Mechanical Circulatory Support edited by Dr. Marvin Slepian. Additionally, many editorials highlighted the worldwide survival differences in hemodialysis and perspectives on mechanical circulatory support and stem cell therapies for cardiac support. We take this time also to express our gratitude to our authors for offering their work to this journal. We offer our very special thanks to our reviewers who give so generously of time and expertise to review, critique, and especially provide meaningful suggestions to the author's work whether eventually accepted or rejected. Without these excellent and dedicated reviewers the quality expected from such a journal could not be possible. We also express our special thanks to our Publisher, John Wiley & Sons for their expert attention and support in the production and marketing of Artificial Organs. We look forward to reporting further advances in the coming years.

EFFECT OF A HIGH-FREQUENCY VIBRATION BOUNDARY ON RBC

The vibrations in blood pumps were often caused by high speed, suspension structure, viscoelastic implantation environment and other factors in practical application. Red blood cell (RBC) was modeled using a nonlinear spring network model. The immersed boundary-lattice Boltzmann method (IB-LBM) was used to investigate the impact of high-frequency vibration boundary on RBC. To confirm the RBC model, the simulation results of RBC stretching were compared with experimental results. We examined the force acting on RBC membrane nodes; moreover, we determined whether RBC energy was affected by different frequencies, amplitudes, and vibration models of the boundary. Furthermore, we examined whether RBC energy was affected by the distance between the top and bottom boundaries. The energy of RBCs in shear flow disturbed by the vibration boundary was also investigated. The results indicate that larger amplitude (Am), frequency (Fr), and opposite vibration velocity of top and bottom boundary produced a larger force that acted on RBC membrane nodes and larger energy changes in RBCs. The vibration boundary may cause turbulence and alter RBC energy. When the blood pump was designed and optimized, the vibration frequency and amplitude of the blood pump body and impeller should be reduced, the phase of the blood pump body and impeller vibration velocity should be close. To alleviate the free energy of RBCs and to reduce RBC injury in the blood pump, the distance between RBCs and the boundary should not be less than 20[Formula: see text][Formula: see text]m.

Fluid Dynamics in the HeartMate 3: Influence of the Artificial Pulse Feature and Residual Cardiac Pulsation

Ventricular assist devices (VADs), among which the HeartMate 3 (HM3) is the latest clinically approved representative, are often the therapy of choice for patients with end-stage heart failure. Despite advances in the prevention of pump thrombosis, rates of stroke and bleeding remain high. These complications are attributed to the flow field within the VAD, among other factors. One of the HM3's characteristic features is an artificial pulse that changes the rotor speed periodically by 4000 rpm, which is meant to reduce zones of recirculation and stasis. In this study, we investigated the effect of this speed modulation on the flow fields and stresses using high-resolution computational fluid dynamics. To this end, we compared Eulerian and Lagrangian features of the flow fields during constant pump operation, during operation with the artificial pulse feature, and with the effect of the residual native cardiac cycle. We observed good washout in all investigated situations, which may explain the low incidence rates of pump thrombosis. The artificial pulse had no additional benefit on scalar washout performance, but it induced rapid variations in the flow velocity and its gradients. This may be relevant for the removal of deposits in the pump. Overall, we found that viscous stresses in the HM3 were lower than in other current VADs. However, the artificial pulse substantially increased turbulence, and thereby also total stresses, which may contribute to clinically observed issues related to hemocompatibility.

Blood damage in Left Ventricular Assist Devices: Pump thrombosis or system thrombosis?

Introduction:

Despite significant technical advancements in the design and manufacture of Left Ventricular Assist Devices, post-implant thrombotic and thromboembolic complications continue to affect long-term outcomes. Previous efforts, aimed at optimizing pump design as a means of reducing supraphysiologic shear stresses generated within the pump and associated prothrombotic shear-mediated platelet injury, have only partially altered the device hemocompatibility.

Methods:

We examined hemodynamic mechanisms that synergize with hypershear within the pump to contribute to the thrombogenic potential of the overall Left Ventricular Assist Device system.

Results:

Numerical simulations of blood flow in differing regions of the Left Ventricular Assist Device system, that is the diseased native left ventricle, the pump inflow cannula, the impeller, the outflow graft and the anastomosed downstream aorta, reveal that prothrombotic hemodynamic conditions might occur at these specific sites. Furthermore, we show that beyond hypershear, additional hemodynamic abnormalities exist within the pump, which may elicit platelet activation, such as recirculation zones and stagnant platelet trajectories. We also provide evidences that particular Left Ventricular Assist Device implantation configurations and specific post-implant patient management strategies, such as those allowing aortic valve opening, are more hemodynamically favorable and reduce the thrombotic risk.

Conclusion:

We extend the perspective of pump thrombosis secondary to the supraphysiologic shear stress environment of the pump to one of Left Ventricular Assist Device system thrombosis, raising the importance of comprehensive characterization of the different prothrombotic risk factors of the total system as the target to achieve enhanced hemocompatibility and improved clinical outcomes.

Normal fluid stresses are prevalent in rotary ventricular assist devices: A computational fluid dynamics analysis

Despite the evolution of ventricular assist devices, ventricular assist device patients still suffer from complications due to the damage to blood by fluid dynamic stress. Since rotary ventricular assist devices are assumed to exert mainly shear stress, studies of blood damage are based on shear flow experiments. However, measurements and simulations of cell and protein deformation show normal and shear stresses deform, and potentially damage, cells and proteins differently. The aim was to use computational fluid dynamics to assess the prevalence of normal stress, in comparison with shear stress, in rotary ventricular assist devices. Our calculations showed normal stresses do occur in rotary ventricular assist devices: the fluid volumes experiencing normal stress above 10 Pa were 0.011 mL (0.092%) and 0.027 mL (0.39%) for the HeartWare HVAD and HeartMate II (HMII), and normal stresses over 100 Pa were present. However, the shear stress volumes were up to two orders of magnitude larger than the normal stress volumes. Considering thresholds for red blood cell and von Willebrand factor deformation by normal and shear stresses, the fluid volumes causing deformation by normal stress were between 2.5 and 5 times the size of those causing deformation by shear stress. The exposure times to the individual normal stress deformation regions were around 1 ms. The results clearly show, for the first time, that while blood within rotary ventricular assist devices experiences more shear stress at much higher magnitudes as compared with normal stress, there is sufficient normal stress exposure present to cause deformation of, and potentially damage to, the blood components. This study is the first to quantify the fluid stress components in real blood contacting devices.

Effect of blade curvature on the hemolytic and hydraulic characteristics of a centrifugal blood pump

Aims:

Impeller design has a significant impact on the overall performance of a blood pump. In this study, the effect of the blade curvature was investigated by performing in silico and in vitro studies on a recently developed centrifugal blood pump.

Methods:

A computational fluid dynamics study was performed for the flow rates of 3–5 L/min at 2000 r/min. The computational fluid dynamics model was also applied on the US Food and Drug Administration (FDA) benchmark blood pump to validate our computational method. The relative hemolysis index was calculated with the Eulerian hemolysis estimation method for five impellers with the wrap angles ranging from 0° to 240°. Hydraulic experiments were conducted for the validation of computational fluid dynamics results. In addition, the curved-blade impeller (120°) and the straight-blade impeller (0°) were evaluated with in vitro hemolysis tests using human blood.

Results:

The wrap angle of 120° provided the best hydraulic and hemolytic performance. Pump achieved the physiologic operating pressures and flows with 85–115 mmHg at 2.5–5.9 L/min. Compared to the straight-blade impeller, the 120° model reduces the relative hemolysis index and the plasma-free hemoglobin near 72.8% and 56.7%, respectively. Comparison of in silico and in vitro results indicated the similar trend to the blade curvature.

Conclusion:

Introducing a blade curvature enhanced the hydrodynamic and hemolytic performance compared to the straight-blade configuration for the investigated centrifugal blood pump. The findings of this study provide new insights into centrifugal blood pump design by examining the influence of the blade curvature.