Corrosion behavior of dental alloys used for retention elements in prosthodontics

Corrosive Studies of a Prosthetic Ni-Cr Alloy Coated with Ti(C,N) Type Layers

Background: Investigating the general corrosion resistance of Ti(C,N) type coatings on a prosthetic nickel alloy in the aspect of their use as protective coatings on prosthetic and orthodontic elements. Methods: Five groups of Ni-Cr alloy samples covered with Ti(C,N) type coatings differing in their carbon and nitrogen contents were used for the tests. The reference group included alloy samples without coatings. The samples were held for 105 days (2520 h) in salt spray chambers and examined by means of the NSS (neutral salt spray) and SWAAT (sea water acetic acid test) tests. After the periods of 14, 28, 81 and 105 days, the samples were removed and weighed, and their weight losses were determined. Results: In the case of each type of Ti(C,N) coating, the mass loss was lower than the mass loss of a sample without a coating, which makes it possible to state that coatings improve the corrosion resistance. No significant differences in the resistance were observed between the particular coatings. The corrosion rate of the examined coatings is close to parabolic. Conclusions: Ti(C,N) type coatings improve the resistance of a prosthetic Ni-Cr alloy and can be used as protective coatings for prosthetic and orthodontic elements.

Experimental Study Regarding the Behavior at Different pH of Two Types of Co-Cr Alloys Used for Prosthetic Restorations

Cobalt-chromium (Co-Cr) alloys are widely utilized in dentistry. The salivary pH is a significant factor, which affects the characteristics and the behavior of dental alloys through corrosion. This study aimed to evaluate the corrosion behavior in artificial saliva with different pH values (3, 5.7, and 7.6) of two commercial Co-Cr dental alloys manufactured by casting and by milling. Corrosion resistance was determined by the polarization resistance technique, and the tests were carried out at 37 ± 1 °C, in Carter Brugirard artificial saliva. After the electrochemical parameters, it can be stated that the cast Co-Cr alloy has the lowest corrosion current density, the highest polarization resistance, and the lowest speed of corrosion in artificial saliva with pH = 7.6. In the case of milled Co-Cr alloy, the same behavior was observed, but in artificial saliva with pH = 5.7, it recorded the most electropositive values of open circuit potential and corrosion potential. Although both cast and milled Co-Cr alloys presented a poorer corrosion resistance in artificial saliva with a more acidic pH value, the milled Co-Cr alloy had better corrosion behavior, making this alloy a better option for the prosthetic treatment of patients suffering from GERD.

Effect of core materials for core fabrication for dental implants on in-vitro cytocompatibility of MC3T3-E1 cells

Background

Despite the wide use of dental materials for CAD/CAM system in prosthetic treatment, the effect of the materials, which are used as dental implants core fabricated, on cells involved in dental implant osseointegration is uncertain. This study aimed to investigate and compare the effect of single core materials used for dental implants fabricated by the dental prostheses fabrication process and the CAD/CAM milling method on MC3T3-E1 cells.

Methods

The materials used for prostheses restoration in this experiment were Porcelain Fused Gold (P.F.G), Lithium disilicate glass ceramic (LiSi₂), Zirconia (ZrO₂), Nickel-Chromium (Ni-Cr) and Cobalt-Chromium (Co-Cr). MC3T3-E1 cells were cultured and used, the cell adhesion and morphology were observed and analyzed using confocal laser scanning microscopy (CLSM). Methoxyphenyl tetrazolium salt (MTS) and alkaline phosphatase (ALP) assay were used to observe the cell proliferation and differentiation.

Results

CLSM revealed irregular cell adhesion and morphology and the filopodia did not spread in the Ni-Cr specimen group. Significantly high cell proliferation was observed in the ZrO₂ specimen group. The LiSi₂ specimen group presented significantly high cell differentiation. Intergroup comparison of cell proliferation and differentiation between the Ni-Cr specimen group and all other specimen groups showed significant differences (p < .05).

Conclusion

Cell proliferation and differentiation were observed from the cores, which were fabricated with all specimen groups on cytocompatibility except the Ni-Cr specimen group.