Effect of the physical properties of acrylic resin of overnight immersion in sodium hypochlorite solution

Effect of disinfectants on multispecies biofilm, the physical and mechanical properties of polymethyl methacrylate, and the corrosion of cobalt chromium alloy

STATEMENT OF PROBLEM

The optimal disinfection protocol that controls adverse effects and promotes effective antimicrobial action on removable prostheses is unclear.

PURPOSE

This in vitro study investigated the effect of disinfectant solutions on the biological, physical, mechanical, and chemical properties of removable prosthesis materials.

MATERIAL AND METHODS

Specimens of polymethyl methacrylate (PMMA) and cobalt chromium (Co-Cr) alloy were immersed in distilled water (PMMA) or artificial saliva (Co-Cr) as the control and in 0.25% sodium hypochlorite (NaOCl0.25%), 0.5% chloramine T (CT0.5%), and 0.15% Triclosan (TR0.15%). The antibiofilm activity was evaluated by microbial load and cell metabolisms of the mixed biofilm. Physical (color change, sorption, solubility, and surface roughness), mechanical (hardness, flexural, and impact strength), and chemical (corrosion) properties were analyzed before and after simulating a 5-year immersion. Laser confocal microscopy, scanning electron microscopy (SEM), and dispersive energy spectroscopy (EDS) complemented the analyses. The data were analyzed by using the Mann-Whitney U test, Kruskal-Wallis with Dunn posttests, 1-way ANOVA, and repeated measures ANOVA (α=.05).

RESULTS

All solutions were effective against bacteria, but only NaOCl0.25% eliminated Candida spp. TR0.15%, and CT0.5% increased cell metabolisms. For interaction (time and solution), there was a reduction in PMMA hardness in the control and TR0.15%. Color, sorption, solubility, and flexural strength did not change. CT0.5% and TR0.15% were similar for impact resistance. CT0.5% caused the lowest roughness. NaOCl0.25% showed the greatest corrosive potential. Dark spots were seen under SEM in Co-Cr stored with NaOCl0.25% and TR0.15%. EDS indicated different proportions of oxygen, cobalt, chromium, and molybdenum.

CONCLUSIONS

NaOCl0.25% had the best antimicrobial action. CT0.5% and TR0.15% have potential. Hardness and roughness changes were clinically acceptable, and the other properties remained unchanged. All the solutions caused color changes. NaOCl0.25% was unsatisfactory for use with Co-Cr, CT0.5% was intermediate, and TR0.15% was suitable.

Effects of simulated long-term exposure to bottled, neutral pH electrolyzed oxidizing water on the properties of denture base resins

STATEMENT OF PROBLEM

Denture stomatitis can pose serious health risks, especially to older people. Chemical denture cleaning agents must be effective, yet not adversely affect the longevity of removable dentures. Ready-to-use (RTU) neutral pH electrolyzed oxidizing water (EOW) is an effective biocide against Candida albicans biofilms on denture resins, but the effects of daily disinfection with EOW on the physical and mechanical properties of resins have not been established.

PURPOSE

The purpose of this in vitro study was to investigate the effects of simulated long-term exposure to RTU EOW on the color, surface characteristics, and flexural strength of denture base resins.

MATERIAL AND METHODS

Heat-polymerized (HP), 3D printed (3D) and computer-aided design and computer-aided manufacture (CAD-CAM)-milled (CC) denture resin specimens (square: 20×20×3.3 mm; beam: 64×10×3.3 mm) were immersed in tap water (TW), RTU EOW (Neutral Anolyte ANK; Envirolyte; EOW), or a commercial denture cleaning tablet solution (Polident 3-Minute; Glaxo SmithKline; PD), mimicking a 5-minute once daily disinfection routine performed up to 3.0 years. Color and surface roughness were recorded (n=3, squares), and changes in color (∆E00) and surface roughness (∆Ra) were calculated. Flexural strength (n=12, beams) and surface hardness (n=18, beams) were measured with a universal testing machine. The fractured surfaces of specimens were examined by scanning electron microscopy and energy dispersive spectroscopy. Data were assessed by performing the Shapiro-Wilk or D'Agostino and Pearson normality tests. Two-way ANOVA or the Kruskal-Wallis test with a post hoc Tukey HSD or Dunn multiple comparisons (α=.05) was used for statistical analyses.

RESULTS

No significant changes were found in either color or surface roughness for HP, 3D, and CC resins after 1.5-year and 3.0-year immersion in any of the agents (P>.05). The surface hardness of 3D resins reduced by 14% with TW and by 23% with EOW and PD at 3.0 years. The flexural strengths of all 3 resins were unaffected by 3.0-year immersion (P>.05).

CONCLUSIONS

Simulated long-term immersion disinfection with RTU neutral pH EOW did not adversely affect the physical and mechanical properties of HP or CC denture resins.

Effect of immersion in disinfectants on the color stability of denture base resins and artificial teeth obtained by 3D printing

PURPOSE

To evaluate the effect of immersion in disinfecting solutions on the color stability of denture base resins and artificial teeth obtained by 3D printing.

MATERIALS AND METHODS

Forty discs (15 × 3 mm) were obtained for each group: Lucitone 550 and Cosmos Denture 3D (denture base resins), Duralay and Cosmos TEMP 3D (artificial teeth resins). The discs were immersed in disinfectant solutions: Corega Tabs, 2% chlorhexidine digluconate, 0.25% sodium hypochlorite, and distilled water. Color measurements were obtained with a spectrophotometer before immersion in disinfectants and after the simulated periods of 6 and 12 months. Data (ΔE00 ) were submitted to mixed three-way ANOVA and Bonferroni post-test.

RESULTS

For denture base resins, Cosmos Denture 3D showed greater color change regardless of the solution and immersion time. The immersion time of 6 months influenced the color change of the denture base resins regardless of the disinfectant solution. For the artificial teeth resins, the immersion time of 12 months showed a significant color change when compared to 6 months. Cosmos TEMP 3D showed greater color change for all solutions, except for 0.25% sodium hypochlorite. Duralay resin showed greater color change in 2% chlorhexidine, regardless of immersion time.

CONCLUSIONS

For denture base resins, the immersion time significantly changed the color regardless of the solution. For artificial teeth resins, Cosmos TEMP 3D showed greater color changes in all solutions when compared to Duralay, except for 0.25% sodium hypochlorite. Chlorhexidine digluconate significantly changed the color of Duralay.

Effects of disinfection with a vinegar-hydrogen peroxide mixture on the surface characteristics of denture acrylic resins

OBJECTIVE

This study aimed to investigate changes in the surface characteristics of two denture resins when disinfected with a vinegar-hydrogen peroxide (VHP) mixture.

MATERIALS AND METHODS

Microwave-polymerized or 3D printed acrylic resin disks were immersed for 900 min (simulating 90 daily uses) in the following solutions (N = 10): water; 0.5% sodium hypochlorite; hydrogen peroxide and water dilution (1:1 ratio); vinegar and water dilution (1:1 ratio); and VHP mixture. Surface roughness, Knoop microhardness, surface free energy, and scanning electron microscopic images were assessed before and after the immersions. Results were compared using the 2-way ANOVA for repeated measures and Tukey test, at 5% significance.

RESULTS

Surface roughness and microhardness did not differ (P > .05) among the solutions and times. Surface free energy and its dispersive component increased (P < .05) for all solutions. All solutions, except for water and VHP mixture, degraded microtopography.

CONCLUSIONS

The VHP mixture was not deleterious to conventional and 3D-printed resin surfaces.

CLINICAL RELEVANCE

Conventional and 3D printed resin dentures can be disinfected with a VHP mixture in a 1:1 ratio because this mixture does not substantially affect the surface characteristics after 90 daily immersions. On the contrary, sodium hypochlorite, hydrogen peroxide, and vinegar solutions, even in low concentrations, should be used with caution for denture disinfection because they may alter the resin microtopography over time.

Effect of denture cleansers on color stability and surface roughness of denture bases fabricated from three different techniques: Conventional heat-polymerizing, CAD/CAM additive, and CAD/CAM subtractive manufacturing

PURPOSE

Denture base materials are commonly exposed to different denture cleansers which can affect their essential properties. This study aimed to assess the effect of denture cleansers on color stability and surface roughness of poly methyl methacrylate (PMMA) denture bases fabricated from different techniques: Conventional heat-polymerizing, CAD/CAM additive and CAD/CAM subtractive.

MATERIALS AND METHODS

In this in vitro study, 24 disc-shaped specimens were fabricated by the mentioned methods for each group. The initial color and surface roughness of specimens were recorded. The specimens were randomly divided into three subgroups (n = 8): a control subgroup (distilled water), and two experimental subgroups of bioactive oxygen tablet (Corega) and 1% sodium hypochlorite solution. Then they were immersed in the solutions simulating 180 days of clinical use. Color change (∆E) was measured by a spectrophotometer according to the CIE L*a*b* color space and the American National Bureau of Standards (NBS = 0.92 × ∆E). Final surface roughness was recorded by a profilometer and its change was calculated. The Kruskal-Wallis test followed by the Wilcoxon signed rank test were used for statistical analyses (α = .05).

RESULTS

The conventional and CAD/CAM subtractive groups showed an increase in surface roughness following immersion in hypochlorite solution (p < .05). After immersion in the solutions, the highest surface roughness was noted in the conventional group, and the lowest in the CAD/CAM additive group. The CAD/CAM additive group experienced a significant color change in hypochlorite solution (p < .05) and showed the highest color change while the CAD/CAM subtractive group showed the lowest color change in all denture cleanser solutions.

CONCLUSION

Although the CAD/CAM additive denture base resins had the lowest surface roughness after exposure to denture cleanser solutions, they showed significant color change, which should be taken into account. Using hypochlorite as a denture cleanser should be cautioned due to its negative effects on the surface roughness and color stability of denture base materials.

Effect of Effervescent Denture Cleansers on 3D Surface Roughness of Conventional Heat Polymerized, Subtractively, and Additively Manufactured Denture Base Resins: An In Vitro Study

PURPOSE

To compare the change in surface roughness of denture bases fabricated using three different techniques (additive manufacturing, subtractive manufacturing, and conventional heat-polymerizing) when immersed in two commonly available denture cleansers.

MATERIALS AND METHODS

One hundred and seventeen disc-shaped denture base specimens (39/group), were fabricated by subtractive manufacturing (Wieland), additive manufacturing (NextDent Denture 3D+), and conventional heat-polymerizing (Meliodent) techniques, following the manufacturers' instructions. Specimens were randomly divided into 3 groups and immersed in two effervescent denture cleansing solutions and distilled water to simulate 180 days of denture cleansing. A 3D optical noncontact surface profilometer was used to record the surface roughness of the tested denture base materials before and after immersion. Two-way ANOVA, followed by Bonferroni post hoc test, was used to assess the effects of denture cleansers on surface roughness of tested denture base resins.

RESULTS

When immersed in Fixodent and Fittydent effervescent denture cleansing solutions, the highest change in absolute surface roughness (∆Sa, in μm) was observed in additively manufactured denture base material (0.181 ±0.018 and 0.079 ±0.008), followed by heat-polymerized denture base material (0.149 ±0.012 and 0.059 ± 0.011), while subtractively manufactured denture base material showed the least change (0.110 ±0.026 and 0.038 ±0.007), respectively. There was a difference in the extent of change in surface roughness between the denture cleansers. The change in surface roughness was much higher with the Fixodent denture cleanser as compared to the Fittydent denture cleanser.

CONCLUSION

Subtractively manufactured denture base resin displayed the lowest change while additively manufactured denture base resin displayed the highest change in surface roughness in both denture cleansers, but the extent of change in surface roughness was variable.

Effect of Denture Disinfectants on the Mechanical Performance of 3D-Printed Denture Base Materials

Denture care and maintenance are necessary for both denture longevity and underlying tissue health. However, the effects of disinfectants on the strength of 3D-printed denture base resins are unclear. Herein, distilled water (DW), effervescent tablet, and sodium hypochlorite (NaOCl) immersion solutions were used to investigate the flexural properties and hardness of two 3D-printed resins (NextDent and FormLabs) compared with a heat-polymerized resin. The flexural strength and elastic modulus were investigated using the three-point bending test and Vickers hardness test before (baseline) immersion and 180 days after immersion. The data were analyzed using ANOVA and Tukey's post hoc test (α = 0.05), and further verified by using electron microscopy and infrared spectroscopy. The flexural strength of all the materials decreased after solution immersion (p < 0.001). The effervescent tablet and NaOCl immersion reduced the flexural strength (p < 0.001), with the lowest values recorded with the NaOCl immersion. The elastic modulus did not significantly differ between the baseline and after the DW immersion (p > 0.05), but significantly decreased after the effervescent tablet and NaOCl immersion (p < 0.001). The hardness significantly decreased after immersion in all the solutions (p < 0.001). The immersion of the heat-polymerized and 3D-printed resins in the DW and disinfectant solutions decreased the flexural properties and hardness.

Do denture cleansers influence the surface roughness and adhesion and biofilm formation of Candida albicans on acrylic resin? Systematic review and meta-analysis

PURPOSE

To evaluate the influence of denture cleansers on the surface roughness, Candida albicans adhesion, and biofilm formation on denture base acrylic resins.

STUDY SELECTION

Electronic databases and gray literature were searched using an individual search strategy. In vitro studies that evaluated the effects of immersion in denture cleansers on the surface roughness (µm) and antimicrobial activity (CFU/mL) on samples of heat-polymerized denture base acrylic resins were included.

RESULTS

After screening, 17 studies were included, and a qualitative synthesis was performed. After assessing the risk of bias, only nine studies were included in the meta-analysis. The meta-analysis results showed that the evaluated solutions (0.5% sodium hypochlorite, 1% sodium hypochlorite, alkaline peroxide, and natural substances) did not influence the roughness of the acrylic resin. However, in the qualitative analysis, it was not possible to confirm an association between roughness and C. albicans adhesion and biofilm formation on the acrylic resin samples.

CONCLUSION

Denture cleansers did not affect the surface roughness of denture base acrylic resins.

Complete denture hygiene solutions: antibiofilm activity and effects on physical and mechanical properties of acrylic resin

BACKGROUND

Appropriated denture hygiene is a predictive factor for longevity of rehabilitation treatment and maintenance of the oral mucosal health. Although, disinfectant solutions are commonly used as denture cleansers, the impact of these solutions on acrylic resin-based dentures remain unclear.

OBJECTIVE

To evaluate, in vitro, the antibiofilm activity of complete denture hygiene solutions and their effects on physical and mechanical properties of acrylic resin.

METHODOLOGY

For antibiofilm activity measurement acrylic resin specimens were contaminated with Candida albicans, Candida glabrata and Streptococcus mutans. After biofilm growth, the specimens were assigned to the hygiene solutions: Distilled water (Control); 0.2% Sodium hypochlorite (SH); Efferdent Power Clean Crystals (EPC) and 6.25% Ricinus communis (RC). The viability of microorganisms was evaluated by agar plate counts. In parallel, physical, and mechanical properties of the acrylic resin were evaluated after simulating a 5-year period of daily immersion in the previously mentioned solutions. The changes in surface roughness, color, microhardness, flexural strength, impact strength, sorption and solubility were evaluated. Data were compared by ANOVA followed by the Tukey test or Kruskal-Wallis followed by the Dunn test depending on the distribution (α=0.05).

RESULTS

Regarding antibiofilm action, SH eliminated all microorganisms while EPC and RC exhibited moderate action against S. mutans (p=0.001) and C. glabrata (p<0.001), respectively. Relative to effects on the physical and mechanical properties of the acrylic resin, RC led to higher values of color change (p=0.030), hardness (p<0.001), surface roughness (p=0.006) and flexural strength (p<0.001). Moreover, RC induced the highest values of changes in solubility (p<0.001). EPC promoted greater changes in surface morphology, whereas immersion in SH retained the initial appearance of the acrylic resin surface. All hygiene solutions reduced the impact strength (p<0.05).

CONCLUSION

SH presented the most effective antibiofilm activity. In addition, changes on properties were observed after immersion in RC, which were considered within acceptable limits.

Color Stability and Surface Properties of PMMA/ZrO2 Nanocomposite Denture Base Material after Using Denture Cleanser

Objectives

This study aimed to evaluate denture cleanser effects on color stability, surface roughness, and hardness of PMMA denture base resin reinforced with nano-ZrO₂.

Materials and Methods

A total of 420 specimens were fabricated of unreinforced and nano-ZrO₂ reinforced acrylic resin at 2.5% and 5%, resulting in 3 main groups. These groups were further subdivided (n = 10) according to immersion solution (distilled water, Corega, sodium hypochlorite, and Renew) and immersion duration. Surface roughness, hardness, and color were measured at baseline (2 days-T₀) in distilled water and then after 180 and 365 days of immersion (T₁ & T₂) in water or denture cleansing solutions. Data was collected and analyzed using two-way ANOVA followed by Bonferroni post hoc test (α = 0.05).

Results

Surface roughness increased significantly after denture cleanser immersion of unmodified and nano-ZrO₂-modified PMMA materials while hardness decreased (P < 0.001). The denture cleansers significantly affected the color of both PMMA denture bases (P < 0.001). The immersion time in denture cleansers significantly affected all tested properties (P < 0.001). Within denture cleansers, NaOCl showed the highest adverse effects (P < 0.05) while Renew showed the least adverse effects.

Conclusion

Denture cleansers can significantly result in color change and alter the surface roughness and hardness of denture base resin even with ZrO₂ nanoparticles addition. Therefore, they should be carefully used.

Surface roughness of acrylic resins used for denture base after chemical disinfection: A systematic review and meta-analysis

OBJECTIVE

This study aimed to systematically review the literature regarding the surface roughness of polymethylmethacrylate (PMMA) for denture bases, disinfected with different chemical agents and analyse the outcomes of the included studies.

BACKGROUND

Various chemical disinfection protocols to clean the removable dental prosthesis are reported in the literature, however systematic reviews analysing the outcomes in the surface roughness of the PMMA are lacking.

METHODS

The Preferred Reporting Items for Systematic Review and Meta-Analyses (PRISMA) checklist was used to structure this systematic review. The inclusion criteria were as follows: clinical trials, in vitro studies, studies in English and studies comparing the effects of chemical disinfection products on the surface roughness of PMMA. An electronic search was performed in the following databases: PubMed/MEDLINE, Scopus and Web of Science.; we also conducted a manual search for articles published in specific journals of dental prostheses and dental materials.

RESULTS

Thirteen in vitro studies in this systematic review and meta-analysis. According to the meta-analysis, the effects of 0.5% (P = .32; MD: 0.06; CI: -0.05 to 0.17; heterogeneity: P < .00001; I²  = 92%) and 1% NaOCl solutions (P = .27; MD: 0.01; CI: -0.01. to 0.03; heterogeneity: P = .03; I²  = 55%) did not statistically differ between the groups studied. Effects of alkaline peroxide were statistically significant (P = .0009; MD: 0.01; CI: 0.01-0.02; heterogeneity: P = .004; I²  = 65%), suggesting that it promotes deterioration of the PMMA surface.

CONCLUSION

The alkaline peroxide, when used as a disinfectant, generated changes on the surface roughness of PMMA and should be used with caution; however, NaOCl, even at different concentrations, caused fewer changes on the surface of the denture base.

Effect of Cleansers on the Colour Stability of Zirconia Impregnated PMMA Bio-Nanocomposite

Exposure of denture base acrylic resins to the oral environment and storage media for extended periods of time results in colour change due to changes in the properties of the material. The purpose of this in vitro study was to assess the colour stability of high-impact heat-polymerized denture base acrylic resin (HI PMMA) impregnated with zirconia nanoparticles after storage in distilled water (DW) and denture cleaners such as Steradent (STD) and Milton (MIL) for 180 days. Ninety specimens of PMMA + Zirconia nanocomposite with varying nanoparticle concentrations (1.5 wt.%, 3.0 wt.%, 5.0 wt.%, 7.0 wt.% and 10 wt.%) were prepared with a diameter and thickness of 25 ± 1.0 mm × 2 ± 0.1 mm and divided into six groups, while each group was further divided into three subgroups: storage in DW (control), STD and MIL. Colour changes were measured with a Minolta Chroma Meter (Minolta, Osaka, Japan), and assessed using the CIE L*a*b* colorimetric system. Data were statistically analysed for colour change with Friedman's Two-way and Kruskal-Wallis tests at a pre-set alpha value level of 0.05. The colour change (ΔΕ) exhibiting significant differences were found among all groups immersed in denture cleaners, and all values increased with time. According to the National Bureau of Standards, the control group displayed the lowest colour change value (ΔΕ = 1.22), and the highest value was for 10 wt.% ZrO₂ while stored in MIL (ΔΕ = 6.07). The values of colour change for storage in water ranged from 0.49 (control) to 1.82 (10 wt.% ZrO₂). The colour change value for the composite group containing 3 wt.% zirconia was clinically acceptable. However, high concentrations of denture cleaners should be avoided, and the shortest cleaning time is recommended to improve the clinical life of the nanocomposite denture base.

Effects of Denture Cleansers on the Flexural Strength of PMMA Denture Base Resin Modified with ZrO2 Nanoparticles

PURPOSE

The additions of zirconium oxide nanoparticles (nano-ZrO₂ ) to denture base materials have produced nanocomposites with satisfactory properties, although there is a lack of research investigating the effects of denture cleansers on these materials. This study aimed to evaluate the effect of denture cleansers on the flexural strength of denture base materials modified with nano-ZrO₂ .

MATERIALS AND METHODS

A total of 270 specimens were fabricated from pure and nano-ZrO₂ reinforced acrylic resins at 2.5% and 5%, resulting in 3 main groups. The groups were further divided into subgroups (n = 10) according to immersion solution (distilled water, Corega, sodium hypochlorite, and Renew) and immersion duration. Flexural strength was measured at baseline (T₀ ) in distilled water and after 180 and 365 days of immersion (T₁ and T₂ ) in denture cleansers. Data were collected and analyzed using repeated measure ANOVA and Bonferroni post hoc tests (α = 0.05).

RESULTS

The flexural strength of the nano-ZrO₂ modified denture base material decreased significantly after immersion in different denture cleansers at different immersion durations in comparison to baseline (T₀ ) (p < 0.001). Sodium hypochlorite showed the highest reduction in flexural strength followed by Corega, while Renew cleansing solution resulted in the least change.

CONCLUSION

Denture cleansers can significantly affect the flexural strength of nano-ZrO₂ modified denture base materials and thus should be used cautiously.

Evaluation of various denture cleansers on color stability and surface topography of polyetherketoneketone, polyamide, and polymethylmethacrylate

The aim of this study was to evaluate the effect of sodium perborate effervescent tablets and citric acid solution on the color stability and surface topography of a new generation of high-performance polymer polyetherketoneketone (PEKK), thermoinjection-molded polyamide, and polymethylmethacrylate (PMMA). Fifty disc-shaped specimens were fabricated (10 mm × 2 mm) from PEKK (P group), polyamide (D group), and PMMA (M group). These groups were divided into five subgroups (n = 10) according to the storage media. The test groups were immersed in the following solutions: distilled water (Control), Corega, Protefix, Perlodent, and Curaprox. The color stability values (ΔE) were measured using a spectrophotometer before and after immersion in distilled water and four different denture cleansers for 8 hr/day for 140 days. Topography alterations after treatments were assessed with scanning electron microscopy (SEM). Data were analyzed by one-way analysis of variance (ANOVA) followed by Tukey's Honest Significant Difference test. The p < .05 was considered significant. All denture cleansers increased the ΔE values relative to the baseline values in the M, D, and P groups (p < .05). The Perlodent denture cleanser demonstrated the highest ΔE value in all groups, which was unacceptable. Curaprox denture cleanser showed the lowest ΔE value in the M and D groups (p < .05). Curaprox in all groups showed a ∆E value less than 3.7. For patients who have PEKK- and polyamide-based prosthesis, the use of citric acid-based cleansers may be more recommended than sodium perborate-containing cleansers because of its clinically acceptable color changes on polymers in terms of color stability.

Silver Nanoparticles Addition in Poly(Methyl Methacrylate) Dental Matrix: Topographic and Antimycotic Studies

The widespread use of nanoparticles (NPs) in medical devices has opened a new scenario in the treatment and prevention of many diseases and infections owing to unique physico-chemical properties of NPs. In this way, silver nanoparticles (AgNPs) are known to have a strong antimicrobial activity, even at low concentrations, due to their ability to selectively destroy cellular membranes. In particular, in the field of dental medicine, the use of AgNPs in different kinds of dental prosthesis matrixes could be a fundamental tool in immunodepressed patients that suffer of different oral infections. Candida albicans (C. albicans), an opportunistic pathogenic yeast with high colonization ability, is one of the causative agents of oral cavity infection. In our work, we added monodispersed citrate-capping AgNPs with a size of 20 nm at two concentrations (3 wt% and 3.5 wt%) in poly(methyl methacrylate) (PMMA), the common resin used to develop dental prostheses. After AgNPs characterization, we evaluated the topographical modification of PMMA and PMMA with the addition of AgNPs by means of atomic force microscopy (AFM), showing the reduction of surface roughness. The C. albicans colonization on PMMA surfaces was assessed by the Miles and Misra technique as well as by scanning electron microscopy (SEM) at 24 h and 48 h with encouraging results on the reduction of yeast viability after AgNPs exposure.

Effect of cleansers on denture base resins’ structural properties

Introduction:

We assessed the effect of different available denture cleansers on the roughness and hardness of polyetherketoneketone, thermoinjection-molded polyamide, and polymethylmethacrylate.

Materials and Methods:

A total of 150 disc-shaped specimens were fabricated (10 mm × 2 mm) from these three denture base resins, and divided into five subgroups ( n = 10) according to immersion procedures. One of these groups subjected to distilled water served as control, whereas other groups were subjected to daily cleansing with four denture cleansers (Corega, Protefix, Curaprox, and Perlodent) for 8 h a day for 140 days. The surface roughness and hardness values of specimens were recorded by measuring twice at baseline, and again after application of chemical solutions. Topography alterations after treatments were assessed with scanning electron microscopy. The data were subjected to statistical analysis and comparison among groups was done using Kruskal Wallis and Wilcoxon Signed Ranks tests. P-value <0.05 was considered significant.

Results:

The surface roughness of polyetherketoneketone, polymethylmethacrylate, and polyamide dentures was increased significantly by chemical solutions of denture cleansers. While the hardness value of polyetherketoneketone was not affected significantly after immersion in denture cleansers, those of polymethylmethacrylate and polyamide decreased significantly. Compared with Curaprox, the effervescent tablets significantly altered the surface hardness and roughness of polyamide.

Conclusion:

Denture cleansers can considerably alter the surface roughness and hardness of denture base resins and should be used carefully depending on the material.

An in vitro study to evaluate and compare the surface roughness in heat-cured denture-based resin and injection-molded resin system as affected by two commercially available denture cleansers

Background:

Denture hygiene is of utmost importance to maintain the dentures as well as the underlying tissues in appropriate health. Various denture cleansers as well as denture-based materials have evolved in the market; however, the effect of denture cleansers on different types of denture-based materials has not been very well documented.

Aim:

The purpose of this in vitro study was to evaluate and compare the surface roughness in heat-cured denture-based resin and injection-molded resin system as affected by two commercially available denture cleansers for a period of 15, 30, and 45 days.

Methodology:

A standardized metal die was fabricated to make 120 denture-based resin discs of uniform dimensions. The samples of heat-cured denture-based resin and injection-molded thermoplastic denture-based resin were immersed in the two denture cleansing solutions for a period of 15, 30, and 45 days, respectively. The surface roughness was evaluated by surface profilometer TR200. The data were subjected to statistical analysis and the comparison of quantitative data was done using unpaired t-test and repeated-measures ANOVA test.

Results:

The surface roughness values (Ra) of heat cured denture base resin samples when immersed in two denture cleansers were 0.22 μm at 0 days, 0.27 and 0.29 μm at 15 days, 0.29 and 0.31 μm at 30 days, 0.30 and 0.31 μm at 45 days whereas for injection moulded samples surface roughness values were 1.31 & 1.27 μm at 0 days, 1.46 & 1.66 μm at 15 days, 1.50 & 1.69 μm at 30 days, and 1.50 & 1.69 μm at 45 days.

Conclusion:

The surface roughness (Ra) increased significantly in injection-molded polyamide denture-based resin samples when immersed in both the denture cleansers. Whereas, heat-cured denture-based resin samples did not reveal any significant surface changes at the various time intervals. Hence, the use of denture cleansers is questionable in thermoplastic resins.

Antimicrobial and cytotoxic effects of denture base acrylic resin impregnated with cleaning agents after long-term immersion

The coadjutant method for denture cleansing most used by denture wearers is immersion in chemical agents, which are toxic when in direct contact with cells. However, clinically, the contact between these chemical agents and prosthetic tissues does not occur directly, but rather with what remained impregnated into acrylic bases, even after rinsing the disinfected dentures. This study evaluated the antimicrobial and cytotoxic effects of a denture acrylic resin after successive cycles of daily overnight immersion in 1% sodium hypochlorite (1%NaClO) and 2% chlorhexidine digluconate (2%CHX), simulating the periods of 9 months or 1.5 year. Microbiological and cytotoxic assays were performed, respectively, by broth microdilution method (Candida albicans or Staphylococcus aureus) and MTT assay. Chemical residues of 2%CHX impregnated into the denture acrylic resin had an antimicrobial effect on both immersion periods, which was not observed with those of 1%NaClO. However, residues of 2%CHX were severely cytotoxic to human gingival fibroblasts compared to those of 1%NaClO and acrylic resin (not submitted to the denture cleansers), which were slightly cytotoxic. Even at low concentrations recommended for overnight soaking of removable dentures, the chemical residues of CHX may result in some degree of toxicity to the denture-bearing mucosa after long-term daily immersion.

Evaluation of biofilm removal and adverse effects on acrylic resin by diluted concentrations of sodium hypochlorite and Ricinus communis solutions

PURPOSE

To verify whether 0.1% and 0.2% sodium hypochlorite (NaOCl), and 8% Ricinus communis (RC) were able to remove denture biofilm without causing deleterious effects to acrylic resin.

BACKGROUND

Previous data show that denture cleansers are effective in reducing biofilm; however, they can change acrylic resin properties.

METHODS

In a crossover trial, 47 denture wearers brushed and soaked their dentures (20 min/14 d): control, 0.85% saline; SH1, 0.1% NaOCl; SH2, 0.2% NaOCl and RC. Denture biofilm on the intaglio surface was stained, photographed and quantified (Image Tool® ). Furthermore, 80 rectangular and 80 disc-shaped specimens (Lucitone 550) were assigned into tested solutions (n = 20), simulating 5 years of daily short immersions (20 minutes). A colorimeter and the National Bureau of Standards units (NBS) determined colour data (ΔE). Surface roughness and flexural strength were measured using rugosimeter and universal testing machine, respectively. Data were compared by the Friedman test (α = .05) followed by Wilcoxon, corrected by Bonferroni (α = .005) (clinical) and Kruskal-Wallis followed by the Dunn test (α = .05) (laboratorial).

RESULTS

SH2 (MR=1.77) showed lower biofilm coverage; SH1 (MR = 2.37) and RC (MR = 2.74) presented intermediated values. RC (1.10 [0.96:1.75]) revealed higher colour alteration than SH1 (0.71 [0.62:0.80]) and SH2 (0.74 [0.58:0.85]); however, NBS classified all solutions as "trace" (0.0-0.5). There was no statistical significance for surface roughness (P = .760) and flexural strength (P = .547).

CONCLUSIONS

The 0.2% NaOCl showed the best clinical performance and did not cause adverse effects on acrylic resin on laboratory analyses.

Rosemary, Castor Oils, and Propolis Extract: Activity Against Candida Albicans and Alterations on Properties of Dental Acrylic Resins

PURPOSE

To evaluate the in vitro activity of 8% rosemary, 2% castor oils, and 12% propolis glycolic extract against Candida albicans, as well as the physical changes of properties in colorless and pink acrylic resins after immersion in these liquids.

MATERIALS AND METHODS

Colorimetric, roughness, and Knoop microhardness assays were evaluated in 25 specimens distributed into five groups (3 test groups and 2 control groups - distilled water and hypochlorite 1%), totaling five specimens per group for each acrylic resin (colorless and pink). The specimens were individually immersed for 30 minutes in 10 mL of these liquids, washed, and dried once a week. They were maintained in distilled water at 37°C between processes during all experiments. The analyses were performed before immersion and in the 4th and/or 12th month. In vitro, 18 acrylic resins were exposed to C. albicans and, after a process of 30 minutes in immersion in the five groups cited and oil vehicle control of vesicle (liquid Vaseline), the specimens were washed and incubated for 24 hours in 37°C. The growth was determined by colony counting. For comparisons between the groups in each trial and the disinfection test, paired Student's t-tests and ANOVA with post hoc Tukey were performed by the SPSS program, considering α = 0.05.

RESULTS

None of the liquids altered the microhardness, but all the natural compounds and 1% sodium hypochlorite (control) altered color and roughness after the 12th month of immersion in these agents. In the colorless specimens, 8% rosemary oil caused a color change similar to water, and less color and roughness alterations when compared to 2% castor oil and 1% sodium hypochlorite, respectively. There was no growth of yeast colonies after immersion in rosemary oil, propolis glycolic extract, and 1% sodium hypochlorite.

CONCLUSION

Eight percent rosemary oil has the potential to be used as an acrylic resin disinfectant.

Effect of Denture Cleansers on Surface Roughness and Flexural Strength of Heat Cure Denture Base Resin-An In vitro Study

INTRODUCTION

Denture cleansing is essential for maintaining the prosthesis and oral health, so choosing an appropriate cleanser which is not only efficient but also not adversely affects the properties of denture base resin itself with prolonged use is important. Hence, the present study was undertaken.

AIM

To evaluate the effect of different chemical cleansers on surface roughness and flexural strength of heat cure denture base resin when used daily for three months.

MATERIALS AND METHODS

A total of 40 rectangular specimens (65 mm x 10 mm x 2.5 mm) and 32 disc shaped specimens (10 mm x 2 mm) were fabricated from heat cure denture base resin (DPI Heat Cure) for evaluation of flexural strength and surface roughness respectively. The specimens not subjected to cleansing served as control whereas other specimens were subjected to daily cleansing with one of the three cleansers (1% sodium hypochlorite, fittydent tablets, 100% vinegar) daily and stored in distilled water for three months. Surface analyser (Surftest SJ-210, Mitutoyo, USA) was used to evaluate change in surface roughness of the specimens (ΔRa) before and after cleansing. Also, flexural strength (S) of specimens after cleansing was evaluated by subjecting the specimens to load of 50 kgf at a crosshead speed of 5 mm/min in universal testing machine (INSTRON). Data obtained by testing was compiled and analysed using statistical software SPSS version 17.5. ANOVA and Post-hoc Tukey's tests were used and p-value <0.05 was considered significant in all tests.

RESULTS

Results showed that the surface roughness of the specimens was significantly increased and flexural strength significantly decreased after immersion in 1% sodium hypochlorite solution for three months (p<0.05). No statistically significant difference were observed in flexural strength and surface roughness of the specimens cleaned with fittydent and 100% vinegar for three months (p>0.05).

CONCLUSION

Within the limitations of this in vitro study, it was concluded that immersion in 1% sodium hypochlorite solutions for three months influences the surface roughness and flexural strength of heat cure denture base resin; hence it should be used with caution when used for long period. Fittydent and 100% vinegar can be recommended as a routine chemical cleansing agent for long term use.

Efficacy of denture cleaners on the surface roughness and Candida albicans adherence of sealant agent coupled denture base materials

This study investigated the effect of denture cleansers on the surface roughness and Candida albicans adherence of surface sealant agent coupled denture base resins. One hundred and twenty specimens were fabricated from 2 polymethyl methacrylate (PMMA) (Meliodent; Acron MC) and 1 polyamide (Deflex) denture base materials, coated with a sealant agent (Palaseal) and divided into 4 groups (n=10) according to overnight cleaning procedures: distilled water (control), 5% sodium hypochlorite (NaOCl) and two different sodium perborate (Corega; Rapident). The surface roughness values were measured with a profilometer before (R_a0) and after 90 days immersion in denture cleaners (R_a1). Specimens were incubated with Candida albicans suspension and Candida colony- forming units (CFU) (Cfu/mm) were counted. Significant differences were found, between the R_a0 and R_a1 values of 5% NaOCl applied Acron MC, Deflex and also Rapident applied Deflex groups (p<0.05). Denture cleaning procedures had no significant effects on the quantitiy of Candida albicans.

Evaluation of Surface Microhardness Following Chemical and Microwave Disinfection of Commercially Available Acrylic Resin Denture Teeth

INTRODUCTION

Denture disinfection is an indispensable procedure for preventing cross contamination and the maintenance of a healthy oral mucosa in patients rehabilitated with removable dental prosthesis. Nevertheless, they are known to cause changes in the physical and mechanical properties of denture base resins and acrylic resin denture teeth following immersion of a denture in a suitable chemical disinfectant solution or by undergoing microwave irradiation. One such mechanical property indicator for artificial tooth materials is hardness.

AIM

To assess the surface hardness of acrylic resin teeth of three different commercial brands (Ivoclar, Newace, Acryrock) following chemical (2% glutaraldehyde, 1% sodium hypochlorite) and microwave disinfections.

MATERIALS AND METHODS

Ten specimens of each of the three commercial brands were made for control and each simulated disinfection type and stored in distilled water at room temperature for 24 hours. After water storage, specimens were immersed in 2% glutaraldehyde and 1% sodium hypochlorite (one and three cycles) at room temperature for 10 minutes. Irradiation with microwave (one and three cycles) was done in domestic microwave for three minutes with the specimens immersed in 150 ml of distilled water. The specimens were stored in distilled water at room temperature for seven days after each disinfection cycle. Vickers hardness measurements were made using a hardness indenter under a load of 50 g force for 10 seconds. Data was subjected to repeated measure two-way ANOVA test and Tukey's test.

RESULTS

There were statistically significant differences for the variables disinfection, tooth, and cycle (p<0.05 for teeth & disinfectant interaction, p<0.05 cycle and disinfectant interaction). The mean surface hardness following one microwave disinfection cycle was lower than control, glutaraldehyde and sodium hypochlorite. Comparison among cycles revealed that microhardness was significantly decreased for three cycles of microwave disinfection.

CONCLUSION

It was concluded that there was no significant difference in microhardness when the teeth were subjected to chemical disinfection but three cycles of microwave disinfection produced decrease in the microhardness of different types of artificial teeth.

The effect of different chemical intra-oral prostheses cleansers on the surface properties of Parylene-coated PMMA

The purpose of this study was to investigate the effect of different chemical intra-oral prosthesis cleansers on the surface properties of Parylene-C coated and non-coated polymethyl methacrylate (PMMA). A total of 120 PMMA samples were prepared. Half of the samples were coated with 10 µm of Parylene-C. Samples were exposed to either air (control) or one of two types of denture cleansers, an alkaline peroxide cleanser (Steradent) or a neutral peroxide cleanser with enzyme (Poligrip). Surface roughness (Ra) and surface free energy (SFE) values were measured and compared between groups. Scanning electron microscopy was used for visual analysis. The samples coated with Parylene exhibited significantly lower mean Ra values compared to the non-coated samples (p<0.001). Immersion in Steradent increased the roughness of non-coated PMMA, but its effect was minimized on the coated surfaces. SFE increased for the samples exposed to air and Poligrip, but decreased for the samples exposed to Steradent.

Effects of Denture Cleansers on Heat-Polymerized Acrylic Resin: A Five-Year-Simulated Period of Use

This study evaluated color stability, surface roughness and flexural strength of acrylic resin after immersion in alkaline peroxide and alkaline hypochlorite solutions, simulating a five-year-period of use. Sixty disc-shaped (16 x 4 mm) and 60 rectangular specimens (65 x 10 x 3.3 mm) were prepared from heat-polymerized acrylic resin (Lucitone 550) and assigned to 3 groups (n = 20) of immersion (20 min): C1: distilled water; AP: warm water and one alkaline peroxide tablet; SH: 0.5% NaOCl solution. Color data (∆E) were determined by a colorimeter and also quantified according to the National Bureau of Standards units. A rugosimeter was used to measure roughness (μm) and the flexural strength (MPa) was measured using a universal testing machine. Data were evaluated by Kruskal-Wallis followed by Dunn tests (color stability and surface roughness) and by one-way ANOVA and Bonferroni test (flexural strength). For all tests was considered α = 0.05. AP {0.79 (0.66;1.42)} caused color alteration significantly higher than C1 {0.45 (0.37;0.57)} and SH {0.34 (0.25;0.42)}. The mean ∆Ε values quantified by NBS were classified as "trace" for C1 (0.43) and SH (0.31) and "slight" for AP (0.96). SH {-0.015 (-0.023;0.003)} caused significantly higher ΔRa than the C1 {0.000 (-0.004;0.010)} and AP {0.000 (-0.009;0.008)} groups. There was no statistically significant difference among the solutions for flexural strength (C1: 84.62 ± 16.00, AP: 85.63 ± 12.99, SH: 84.22 ± 14.72). It was concluded that immersion in alkaline peroxide and NaOCl solutions simulating a five-year of 20 min daily soaking did not cause clinically significant adverse effects on the heat-polymerized acrylic resin.

Efficacy of citronella and cinnamon essential oils on Candida albicans biofilms

INTRODUCTION

The discovery of new antimicrobials derived from plants could aid in the management of biofilm-associated infections, including denture-induced stomatitis (DS). DS is an oral infection caused by Candida biofilms on the surfaces of poorly cleansed dentures. Effective treatment of DS requires the use of an appropriate denture cleanser and preferably one that exhibits antimicrobial properties.

OBJECTIVE

This study aimed to evaluate the anti-Candida and anti-biofilm efficacy of two essential plant oils from Cymbopogon winterianus (citronella) and Cinnamon cassia (cinnamon).

MATERIALS AND METHODS

Minimum Inhibitory Concentrations (MICs) and Minimum Fungicidal Concentrations (MFCs) were determined by broth microdilution, whilst anti-biofilm activity was measured against mature (cultured for 72 h) biofilms on acrylic surfaces. Candida cell viability was assessed immediately (0 h) after treatment (T0) and 48 h after biofilm re-growth (T48). Biofilm structure was determined using Scanning Electron Microscopy (SEM) at T0 and T48.

RESULTS

The respective MICs of cinnamon and citronella oils were 65 and 250 μg/ml and these were also the MFC values. For anti-biofilm efficacy, both oils significantly (p < 0.05) reduced the number of viable micro-organisms and accumulation of biofilms at T0. However, at T48, there was no difference between treated and untreated biofilms.

CONCLUSIONS

It is concluded that citronella and cinnamon essential oils have potential for daily anti-candidal denture cleansing.

Bond Strength of Artificial Teeth Attached to a Microwave-Polymerized Denture Base Resin after Immersion in Disinfectant Solutions

PURPOSE

To evaluate the bond strength between two types of acrylic resin teeth and a microwave denture base resin after immersion in disinfectant solutions for 180 days.

MATERIALS AND METHODS

Eighty specimens made of acrylic resin teeth (Biotone and Biotone IPN) attached to a microwave polymerized denture base resin (Nature-Cryl MC) were divided into eight groups (n = 10) according to the treatment (distilled water-control, 2% chlorhexidine digluconate, 1% sodium hypochlorite and sodium perborate solution-Corega Tabs). The shear strength tests (MPa) were carried out using a universal testing machine with a 0.5 mm/min speed. Data analysis was performed using ANOVA and multiple comparison Student-Newman-Keuls post hoc test (α = 0.05).

RESULTS

Biotone IPN showed similar results among the groups (distilled water, 8.25 ± 1.81 MPa; chlorhexidine, 7.81 ± 3.34 MPa; hypochlorite, 7.75 ± 3.72 MPa; and Corega Tabs, 7.58 ± 2.27 MPa, whereas Biotone showed significantly lower shear bond strength values for the groups immersed in Corega Tabs (5.25 ± 3.27 MPa) and chlorhexidine (6.08 ± 2.35 MPa).

CONCLUSIONS

Soaking the dentures in 1% sodium hypochlorite could be recommended as a disinfectant solution for dentures fabricated with conventional acrylic resin denture teeth and microwave denture base resin. For dentures fabricated with IPN teeth and microwave denture base resin, all the soaking solutions evaluated in this study could be suggested to denture wearers.

Effect of cleanser solutions on the color of acrylic resins associated with titanium and nickel-chromium alloys

This study evaluated the effect of cleanser solutions on the color of heat-polymerized acrylic resin (HPAR) and on the brightness of dental alloys with 180 immersion trials. Disk-shaped specimens were made with I) commercially pure titanium, II) nickel-chromium-molybdenum-titanium, III) nickel-chromium molybdenum, and IV) nickel-chromium-molybdenum beryllium. Each cast disk was invested in the flasks, incorporating the metal disk into the HPAR. The specimens (n=5) were then immersed in solutions containing: 0.05% sodium hypochlorite, 0.12% chlorhexidine digluconate, 0.500 mg cetylpyridinium chloride, a citric acid tablet, one of two different sodium perborate/enzyme tablets, and water. The color measurements (∆E) of the HPAR were determined by a colorimeter in accordance with the National Bureau of Standards. The surface brightness of the metal was visually examined for the presence of tarnish. The results (ANOVA; Tukey test-α=0.05) show that there was a significant difference between the groups (p<0.001) but not among the solutions (p=0.273). The highest mean was obtained for group III (5.06), followed by group II (2.14). The lowest averages were obtained for groups I (1.33) and IV (1.35). The color changes in groups I, II and IV were slight but noticeable, and the color change was considerable for group III. The visual analysis showed that 0.05% sodium hypochlorite caused metallic brightness changes in groups II and IV. It can be concluded that the agents had the same effect on the color of the resin and that the metallic alloys are not resistant to the action of 0.05% sodium hypochlorite.

Antifungal activity of components used for decontamination of dental prostheses on the growth of Candida albicans

Introduction: The effectiveness of antimicrobial solutions employed in dental prosthesis decontamination is still uncertain. Aim: To evaluate the antifungal activity of cleaners used in the decontamination of dental prostheses on the growth of Candida albicans. Material and method: The evaluated products were: Corega Tabs(r) (S1), Sodium Hypochlorite 1% (S2), Sodium Bicarbonate 1% (S3), Hydrogen Peroxide 1% (S4), Chlorhexidine Digluconate 0.12% - Periogard (r) (S5), Mouthrinse based on essential oils - Listerine(r) (S6), essential oil from Rosmarinus officinalis (rosemary) at concentrations of 1% (S7) and 2% (S8). The antifungal activity of the products was evaluated by agar diffusion technique and the determination of microbial death curve of samples of C. albicans (ATCC 90028) in concentration 1.5 × 106 CFU/mL. The tests were performed in triplicate and statistical analysis was made by ANOVA Two-Way and Tukey tests, with the confidence level of 95%. Result: The average of the zones of inhibition growth, in millimeters, obtained for the products were: 0.0 (S1), 44.7 (S2), 0.0 (S3), 21.6 (S4), 10.0 (S5), 6.1 (S6), 0.0 (S7) and 2.4 (S8). Considering the determination of microbial death curve, all products showed a statistical difference (p<0.01) from control (0.85% sodium chloride) and S3 groups. Fungal growth less than 2×104 CFU/mL and an accentuation of the microbial death curve were observed after 30 minutes, with exception for S3 and control groups. Conclusion: The studied compounds, with the exception of Sodium Bicarbonate, have antifungal effect against C. albicans, which contribute for dental prostheses hygiene.

Color Stability, Surface Roughness and Flexural Strength of an Acrylic Resin Submitted to Simulated Overnight Immersion in Denture Cleansers

This study evaluated color stability, surface roughness and flexural strength of acrylic resin specimens after immersion in alkaline peroxide and alkaline hypochlorite, simulating a period of one and a half year of use of overnight immersion. Sixty disc-shaped (16X4 mm) and 80 rectangular specimens (65X10X3.3 mm) were prepared from heat-polymerized acrylic resin (Lucitone 550) and distributed into 4 groups (n=20): C1: without immersion, C2: 8 h immersion in distilled water; AP: 8 h immersion in alkaline peroxide effervescent tablet; SH: 8 h immersion in 0.5% NaOCl solution. Properties were evaluated at baseline and after the immersion. Color data were also calculated according the National Bureau of Standards (NBS). Results were analyzed statistically by ANOVA and Tukey's HSD test (α=0.05). AP (2.34 ± 0.41) caused color alteration significantly higher than C2 (0.39 ± 0.30) and SH (1.73 ± 0.52). The mean ΔE values were classified as indicial for C2 (0.36 ± 0.29) and noticeable for AP (2.12 ± 0.39) and SH (1.59 ± 0.48). SH (0.0195 ± 0.0150) caused significantly higher ΔRa (p=0.000) than the C2 (0.0005 ± 0.0115) and PA (0.0005 ± 0.0157) groups. There was no statistically significant difference (p=0.063) among the solutions for flexural strength (C1: 105.43 ± 14.93, C2: 100.30 ± 12.43, PA: 97.61 ± 11.09, SH: 95.23 ± 10.18). In conclusion, overnight immersion in denture cleansing solutions simulating a year and a half of use did not alter the flexural strength of acrylic resin but caused noticeable color alterations, higher for alkaline peroxide. The 0.5% NaOCl solution caused increase in surface roughness.