Exploring microwave irradiation as a method to disinfect contact lens cases

PURPOSE

Biofilm formation caused by infrequent contact lens case replacement and the ineffectiveness of multi-purpose solutions (MPS) on biofilm removal is associated with high rates of bacterial keratitis infections. This study demonstrated biofilm elimination from the contact lens case by microwave irradiation.

METHODS

Staphylococcus aureus biofilms indicative of 3-9 months of contact wear were cultured in contact lens cases and visualized with crystal violet (CV) staining. Biofilms in contact cases were then exposed to four treatment regimens: No treatment (n = 8), 45 s microwave irradiation (n = 8), tap water (n = 6), and MPS (n = 9). Bacterial survival was assessed by colony forming unit (CFU) assay using streak dilutions.

RESULTS

Visualization of the biofilms through CV staining revealed that biofilms coalesce between ribs of the contact case. In 5/8 cases no CFU were cultivated from the case after treatment with microwave irradiation. In tap water and MPS the first dilution averaged 6 ± 2 and 31 ± 13 CFUs per plate, respectively, while microwave irradiation averaged < 1 CFU per plate. In Dilution 2, the average reduced to 0.7 ± 0.7 and 6 ± 5 CFUs per plate for tap water and MPS, respectively, while microwave irradiation had 0 CFUs in Dilution 2.

CONCLUSION

Biofilms that coalesce between the ribs of the contact case pose a threat because this area is difficult to thoroughly scrub and could act as a basis for infection through fouling of contact lenses. Of the four treatment regimens, microwave irradiation displayed the most consistent and highest rate of bacterial eradication. Tap water was less effective compared to microwave irradiation, and poses other harmful side effects, but greatly reduced CFU count compared to no treatment. MPS displayed the poorest bacterial eradication of the treatments. Thus, microwave irradiation is worth further investigation as a viable in-home disinfecting option.

Does microwave and hydrogen peroxide disinfection reduce Candida albicans biofilm on polymethyl methacrylate denture surfaces?

STATEMENT OF PROBLEM

Whether the disinfection of polymethyl methacrylate (PMMA) dentures eliminates Candida albicans biofilm is unclear.

PURPOSE

The purpose of this in vitro study was to determine the antimicrobial effect of immersion in hydrogen peroxide (H₂O₂) and subsequent application of microwaves on the formation of C albicans biofilm on the surface of polished and unpolished PMMA disks.

MATERIAL AND METHODS

Polished and unpolished PMMA disks (n=40) were mounted in a Center for Disease Control (CDC) biofilm reactor by adding yeast-dextrose-peptone (YPD) broth inoculated with C albicans in a cell suspension for 24 hours. After this period, the PMMA disks (n=8) were disinfected with 5 different solutions: saline solution, 1% sodium hypochlorite (NaOCl), H₂O₂, H₂O₂ microwaved at 650 W for 3 minutes (H₂O₂/μw), and distilled water microwaved at 650 W for 3 minutes (H₂O/μw). On the polished and unpolished surface of each disk, arbitrary fluorescence units (AFU) were quantified with the live/dead bacterial viability kit (Invitrogen) by using confocal laser scanning microscopy (CLSM) to evaluate 10 different areas of each surface; these were counted as the colony-forming units (CFUs). The mean values were compared by using the Mann-Whitney U test (α=.05).

RESULTS

Polished surfaces disinfected with H₂O₂/μw obtained the lowest viable cells (9.76 AFU) and nonviable cells (12.46 AFU) compared with H₂O/μw and H₂O_2. In the unpolished surface the lowest mean values of viable cells (14.64 AFU) and nonviable cells (12.46 AFU) were obtained for the PMMA disks disinfected with H₂O/μw compared with H₂O₂/μw and H₂O₂. Both polished and unpolished disks showed significant difference (P<.05) compared with the group of PMMA disks immersed in saline solution. No CFUs were detected in the polished or unpolished PMMA disks immersed in H₂O₂/μw or in NaOCl.

CONCLUSIONS

H₂O₂ alone did not eliminate the formation of the biofilm of C albicans; however, in combination with the use of the microwave at 650 W for 3 minutes, the biofilm formation of C albicans on polished surfaces was reduced. The number of AFUs of viable-nonviable cells and CFUs depended on whether the surfaces are polished or unpolished.

Identification of Candida species isolated from vulvovaginitis using matrix assisted laser desorption ionization-time of flight mass spectrometry

Background and Purpose:

Vulvovaginal candidiasis (VVC) is a common problem in women. The purpose of this study was to identify Candida isolates by matrix assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) from women with vulvovaginitis that were referred to Ghaem Hospital, Mashhad, Iran.

Materials and Methods:

This study was conducted on 65 clinical samples isolated from women that were referred to Ghaem Hospital. All specimens were identified using phenotyping techniques, such as microscopy and culture on Sabouraud dextrose agar and corn meal agar. In addition, all isolates were processed for MALDI-TOF MS identification.

Results:

Out of the 65 analyzed isolates, 61 (94%) samples were recognized by MALDI-TOF MS. However, the remaining four isolates (6%) had no reliable identification. According to the results, C. albicans (58.5%) was the most frequently isolated species, followed by C. tropicalis (16.9%), C. glabrata (7.7%), C. parapsilosis (7.7%), and guilliermondii (3.1%).

Conclusion:

As the findings indicated, MALDI TOF MS was successful in the identification of clinical Candida species. C. albicans was identified as the most common Candida species isolated from the women with VVC. Moreover, C. tropicalis was the most common species among the non-albicans Candida species.

Antifungal, optical, and mechanical properties of polymethylmethacrylate material incorporated with silanized zinc oxide nanoparticles

Background

Fungal infected denture, which is typically composed of polymethylmethacrylate (PMMA), is a common problem for a denture wearer, especially an elderly patient with limited manual dexterity. Therefore, increasing the antifungal effect of denture by incorporating surface modification nanoparticles into the PMMA, while retaining its mechanical properties, is of interest.

Aim of the study

This study aimed to evaluate antifungal, optical, and mechanical properties of heat-cured PMMA incorporated with different amounts of zinc oxide nanoparticles (ZnOnps) with or without methacryloxypropyltrimethoxysilane modification.

Materials and methods

Specimens made from heat-cured PMMA containing 1.25, 2.5, and 5% (w/w) nonsilanized (Nosi) or silanized (Si) ZnOnps were evaluated. Specimens without filler served as control. The fungal assay was performed placing a Candida albicans suspension on the PMMA surface for 2 h, then Sabouraud Dextrose Broth was added, and growth after 24 h was determined by counting colony forming units on agar plates. A spectrophotometer was used to measure the color in L* (brightness), a* (red-green), b* (yellow-blue) and opacity of the experimental groups. Flexural strength and flexural modulus were determined using a three-point bending test on universal testing machine after 37°C water storage for 48 h and 1 month.

Results

The antifungal, optical, and mechanical properties of the PMMA incorporated with ZnOnps changed depending on the amount. With the same amount of ZnOnps, the silanized groups demonstrated a greater reduction in C. albicans compared with the Nosi groups. The color difference (ΔE) and opacity of the Nosi groups were greater compared with the Si groups. The flexural strength of the Si groups, except for the 1.25% group, was significantly greater compared with the Nosi groups.

Conclusion

PMMA incorporated with Si ZnOnps, particularly with 2.5% Si ZnOnps, had a greater antifungal effect, less color differences, and opacity compared with Nosi ZnOnps, while retaining its mechanical properties.

Effectiveness of Chemical and Microwave Disinfection on Denture Biofilm Fungi and the Influence of Disinfection on Denture Base Adaptation

The aims of this study were to evaluate the effectiveness of six disinfection methods and the influence of these methods on the adaptation of maxillary dentures. Acrylic resin specimens contaminated with fungi were exposed to the following disinfection treatments: 1. microwave oven (900 W) at full power for 5 min (with soaking the specimen in 250 ml water), 2. microwave oven at medium power for 5 min (with soaking the specimen in 250 ml water), 3. sodium hypochlorite 5.25 % for 5 min, 4. diluted sodium hypochlorite 1:420 for 5 h, 5. Chlorhexidine gluconate for 5 h, 6. effervescent tablets for 15 min, 7. soaking in 250 ml tap water for 15 min. Colony forming units (CFUs) of remaining cells were counted and compared with t test (p ≤ 0.05). Dimensional stability was evaluated using aluminum die simulating the maxillary edentulous arch. Posterior palatal gaps were measured. Data were analyzed using one-way ANOVA test and t test (p ≤ 0.05). Microwave irradiation (at full or medium power) and sodium hypochlorite 5.25 % for 5 min were able to reduce the CFUs of fungi by more than 4 log10 whereas diluted sodium hypochlorite, chlorhexidine gluconate, and effervescent tablets did not achieve a reduction of >2.8, 2.68 and 1.66, respectively. For dimensional stability test, t test revealed significant difference between control group and the microwave at full power group (p = 0.000). Within the limits of this study, microwave oven at medium power and sodium hypochlorite (5.25 %) are effective and safe methods of disinfecting removable dentures.

Influence of melaleuca and copaiba oils on Candida albicans adhesion

OBJECTIVE

To evaluate the efficacy of Melaleuca alternifolia and Copaifera officinalis in inhibiting the adhesion of Candida albicans biofilm.

BACKGROUND

Over 65% of denture wearers suffer from denture stomatitis, which is one of the most prevalent forms of oral candidiasis. This disease is characterised by the inflammation of the oral mucosa in contact with the contaminated denture. The contaminated denture contributes to the switch of C. albicans from yeast to its pathogenic hyphal form. Candida albicans adheres and colonises the polymethylmethacrylate resin surfaces and thus contributes to the development of denture stomatitis.

MATERIALS AND METHODS

The minimal inhibitory concentration (MIC) of M. alternifolia and Co. officinalis was assessed by the agar dilution method. Sixty-six thermopolymerised acrylic resin squares were used and treated with phosphate-buffered saline, sodium hypochlorite 1%, melaleuca 0.75%, melaleuca 0.375%, melaleuca 0.188% and copaiba 10%. For adherence and biofilm formation, the treated squares were placed in six-well tissue culture plates containing 1 × 10(7)  cells/ml of ATCC1023 or SC5314 in Roswell Park Memorial Institute (RPMI) medium, and after 12 h, the planktonic cells were counted.

RESULTS

Copaiba oil did not inhibit C. albicans growth. However, melaleuca oil showed an MIC value of 0.375% (3.4 mg/ml) for ATCC10231 and 0.093% (0.84 mg/ml) for SC5314.

CONCLUSIONS

Our results demonstrated that M. alternifolia oil inhibited the growth of C. albicans. Moreover, both oils promoted significant adhesion reduction in the tested strains. These findings suggest the possibility of using these oils in prophylaxes against candidiasis.

In vitro and in vivo removal of oral Candida from the denture base

OBJECTIVES

To clarify the effectiveness of ultrasonic cleaning for removing Candida lodged in the denture base.

MATERIALS AND METHODS

In vitro - Specimens of acrylic resin for denture plates contaminated with Candida cells were ultrasonically cleaned for 30 min. Washings were sampled every 5 min and cultured to investigate residual contamination, measured as colony forming units/ml, and the surfaces of the specimens were subjected to low-vacuum scanning electron microscopy (LV-SEM). In vivo - A total of 24 maxillary denture bases were brushed for 2 min under running tap water, then ultrasonically cleaned for 30 min. The washings were sampled every 5 min and cultured to investigate residual contamination.

RESULTS

In vitro - Maximum removal was achieved during the first 5 min of cleaning, with the mean CFU/ml counts significantly declining over time. More than 85% of all Candida was removed within the first 15 min in specimens inoculated with phosphate-buffered saline suspensions of Candida albicans and Candida glabrata. LV-SEM revealed a decreased number of Candida on the surface of the specimens after 30 min of ultrasonic cleaning. In vivo - Maximum removal was achieved during the first 5 min of cleaning, then the mean CFU/ml count significantly declined during the first 10 min. Ultrasonic cleaning for 15 min removed 88.4% of Candida species from the denture base.

CONCLUSIONS

Ultrasonic cleaning is a reliable and simple method for removing Candida lodged in the denture base.

Effect of chemical and microwave disinfection on the surface microhardness of acrylic resin denture teeth

PURPOSE

The purpose of this study was to evaluate the effect of simulated disinfections (2% glutaraldehyde, 1% sodium hypochlorite, and microwave energy) on the surface hardness of Trilux, Biocler, Biotone, New Ace, and Magister commercial artificial teeth.

MATERIALS AND METHODS

Specimens (n = 10) were made with the teeth included individually in circular blocks of acrylic resin, leaving the labial surface exposed. Cycles of simulated chemical disinfection were accomplished with the specimens immersed in the solutions at room temperature for 10 minutes, followed by tap water washing for 30 seconds and storage in distilled water at room temperature for 7 days until the next disinfection. Simulated disinfection by microwave energy was carried out in a domestic oven with 1300 W at a potency of 50% for 3 minutes with the specimens individually immersed in 150 ml of distilled water. Control (no disinfection) and the experimental groups (first and third disinfection cycles) were submitted to Knoop hardness measurements with indentations at the center of the labial tooth surface. Data were submitted to repeated measure two-way ANOVA and Tukey's test (α = 0.05).

RESULTS

Biocler, Magister, and Trilux showed lower surface microhardness when submitted to microwave. Lower microhardness for Biotone was promoted by hypochlorite, while no significant difference was shown for New Ace. The third disinfection cycle significantly decreased the tooth surface hardness only for microwave.

CONCLUSIONS

Different disinfection methods promoted different effects on the microhardness of different types of artificial teeth. Surface microhardness of the teeth was less affected by the simulated chemical disinfections when compared to microwaved specimens.