Comparison between DEXA and finite element studies in the long-term bone remodeling of an anatomical femoral stem

Influence of different CCD angles on osseointegration and radiological changes after total hip arthroplasty of a triple wedge shape cementless femoral stem: a prospective cohort study

PURPOSE

The purpose of this study was to evaluate the osseointegration and radiological outcomes in patients after total hip arthroplasty, hypothesizing different load patterns with one cementless stem design and different CCD angles (CLS Spotorno femoral stem 125° vs 135°).

METHODS

All cases of degenerative hip osteoarthritis fulfilling strict inclusion criteria were treated with cementless hip arthroplasty between 2008 and 2017. Ninety-two out of one hundred six cases were clinically and radiologically examined three and 12 months after implantation. Two groups with each 46 patients were rendered prospectively and compared in clinical (Harris Hip Score) and radiological outcome.

RESULTS

At final follow-up, no significant difference regarding Harris Hip Score was detected between the two groups (mean 99.2 ± 3.7 vs. 99.3 ± 2.5; p = 0.73). Cortical hypertrophy was found in none of the patients. Stress shielding was seen in a total of 52 hips (n = 27 vs. n = 25; 57% of the 92 hips). No significant difference regarding stress shielding was detected when comparing both groups (p = 0.67). Significant bone density loss was detected in Gruen zone one and two in the 125° group. The 135° group showed significant radiolucency in Gruen zone seven. No overall radiological loosening or subsidence of the femoral component was observed.

CONCLUSION

According to our results, the use of a femoral component with a 125° CCD angle versus a 135° CCD did not result in a different osseointegration and load transfer with a clinically relevant significance.

Is the strain pattern of conventional stems negatively affected by a previously short stem THA? An experimental study in cadavaric bone

BACKGROUND

A short stem hip arthroplasty can be revised in many cases using a conventional stem. Furthermore, in some cases the implantation of a short stem is intended, but intraoperatively reasons may lead to the decision to implant a conventional stem after previous preparation of a short stem.

OBJECTIVE

In both cases it is questionable if the anchorage of a conventional stem is negatively affected by the previous preparation of a short stem. In clinical practice mid- or long-term follow up for these special cases hardly exist.

METHODS

The strain patterns for the conventional Bicontact stem in primary implantation and after preparation of the proximal femur for a METHA short stem were tested biomechanically in three pairs of cadaveric femora.

RESULTS

The strain patterns for the conventional Bicontact after preparation of the METHA short stem were similar to conditions after testing the conventional stem in primary conditions.

CONCLUSIONS

These data lead to the consequence that in clinical practise the implantation of a conventional stem after preparation of a short stem and even after revision of a short stem is possible without increased risk of loosening or long-term stress-shielding.

Effect of femoral canal shape on mechanical stress distribution and adaptive bone remodelling around a cementless tapered-wedge stem

OBJECTIVES

In total hip arthroplasty (THA), the cementless, tapered-wedge stem design contributes to achieving initial stability and providing optimal load transfer in the proximal femur. However, loading conditions on the femur following THA are also influenced by femoral structure. Therefore, we determined the effects of tapered-wedge stems on the load distribution of the femur using subject-specific finite element models of femurs with various canal shapes.

PATIENTS AND METHODS

We studied 20 femurs, including seven champagne flute-type femurs, five stovepipe-type femurs, and eight intermediate-type femurs, in patients who had undergone cementless THA using the Accolade TMZF stem at our institution. Subject-specific finite element (FE) models of pre- and post-operative femurs with stems were constructed and used to perform FE analyses (FEAs) to simulate single-leg stance. FEA predictions were compared with changes in bone mineral density (BMD) measured for each patient during the first post-operative year.

RESULTS

Stovepipe models implanted with large-size stems had significantly lower equivalent stress on the proximal-medial area of the femur compared with champagne-flute and intermediate models, with a significant loss of BMD in the corresponding area at one year post-operatively.

CONCLUSIONS

The stovepipe femurs required a large-size stem to obtain an optimal fit of the stem. The FEA result and post-operative BMD change of the femur suggest that the combination of a large-size Accolade TMZF stem and stovepipe femur may be associated with proximal stress shielding.Cite this article: M. Oba, Y. Inaba, N. Kobayashi, H. Ike, T. Tezuka, T. Saito. Effect of femoral canal shape on mechanical stress distribution and adaptive bone remodelling around a cementless tapered-wedge stem. Bone Joint Res 2016;5:362-369. DOI: 10.1302/2046-3758.59.2000525.

Cementless hydroxyapatite coated hip prostheses

More than twenty years ago, hydroxyapatite (HA), calcium phosphate ceramics, was introduced as a coating for cementless hip prostheses. The choice of this ceramic is due to its composition being similar to organic apatite bone crystals. This ceramic is biocompatible, bioactive, and osteoconductive. These qualities facilitate the primary stability and osseointegration of implants. Our surgical experience includes the implantation of more than 4,000 cementless hydroxyapatite coated hip prostheses since 1990. The models implanted are coated with HA in the acetabulum and in the metaphyseal area of the stem. The results corresponding to survival and stability of implants were very satisfactory in the long-term. From our experience, HA-coated hip implants are a reliable alternative which can achieve long term survival, provided that certain requirements are met: good design selection, sound choice of bearing surfaces based on patient life expectancy, meticulous surgical technique, and indications based on adequate bone quality.

Correlation between mechanical stress by finite element analysis and 18F-fluoride PET uptake in hip osteoarthritis patients

18F-fluoride positron emission tomography (18F-fluoride PET) is a functional imaging modality used primarily to detect increased bone metabolism. Increased 18F-fluoride PET uptake suggests an association between increased bone metabolism and load stress at the subchondral level. This study therefore examined the relationship between equivalent stress distribution calculated by finite element analysis and 18F-fluoride PET uptake in patients with hip osteoarthritis. The study examined 34 hips of 17 patients who presented to our clinic with hip pain, and were diagnosed with osteoarthritis or pre-osteoarthritis. The hips with trauma, infection, or bone metastasis of cancer were excluded. Three-dimensional models of each hip were created from computed tomography data to calculate the maximum equivalent stress by finite element analysis, which was compared with the maximum standardized uptake value (SUVmax) examined by 18F-fluoride PET. The SUVmax and equivalent stress were correlated (Spearman's rank correlation coefficient ρ=0.752), and higher equivalent stress values were noted in higher SUVmax patients. The correlation between SUVmax and maximum equivalent stress in osteoarthritic hips suggests the possibility that 18F-fluoride PET detect increased bone metabolism at sites of stress concentration. This study demonstrates the correlation between mechanical stress and bone remodeling acceleration in hip osteoarthritis.

Four decades of finite element analysis of orthopaedic devices: where are we now and what are the opportunities?

Finite element has been used for more than four decades to study and evaluate the mechanical behaviour total joint replacements. In Huiskes seminal paper "Failed innovation in total hip replacement: diagnosis and proposals for a cure", finite element modelling was one of the potential cures to avoid poorly performing designs reaching the market place. The size and sophistication of models has increased significantly since that paper and a range of techniques are available from predicting the initial mechanical environment through to advanced adaptive simulations including bone adaptation, tissue differentiation, damage accumulation and wear. However, are we any closer to FE becoming an effective screening tool for new devices? This review contains a critical analysis of currently available finite element modelling techniques including (i) development of the basic model, the application of appropriate material properties, loading and boundary conditions, (ii) describing the initial mechanical environment of the bone-implant system, (iii) capturing the time dependent behaviour in adaptive simulations, (iv) the design and implementation of computer based experiments and (v) determining suitable performance metrics. The development of the underlying tools and techniques appears to have plateaued and further advances appear to be limited either by a lack of data to populate the models or the need to better understand the fundamentals of the mechanical and biological processes. There has been progress in the design of computer based experiments. Historically, FE has been used in a similar way to in vitro tests, by running only a limited set of analyses, typically of a single bone segment or joint under idealised conditions. The power of finite element is the ability to run multiple simulations and explore the performance of a device under a variety of conditions. There has been increasing usage of design of experiments, probabilistic techniques and more recently population based modelling to account for patient and surgical variability. In order to have effective screening methods, we need to continue to develop these approaches to examine the behaviour and performance of total joint replacements and benchmark them for devices with known clinical performance. Finite element will increasingly be used in the design, development and pre-clinical testing of total joint replacements. However, simulations must include holistic, closely corroborated, multi-domain analyses which account for real world variability.

Comparison between mechanical stress and bone mineral density in the femur after total hip arthroplasty by using subject-specific finite element analyses

The mechanism underling bone mineral density (BMD) loss that occurs in the femur after total hip arthroplasty (THA) remains unknown. We compared the equivalent stress and strain energy density (SED) to BMD in the femur after THA using subject-specific finite element analyses. Twenty-four patients who had undergone primary cementless THA were analysed. BMD was measured using dual-energy X-ray absorptiometry (DEXA) at 1 week and 3, 6 and 12 months after THA. Seven regions of interest (ROIs) were defined in accordance with Gruen's system (ROIs 1-7). Computed tomography images of the femurs were acquired pre- and postoperatively, and the images were converted into three-dimensional finite element (FE) models. Equivalent stress and SED were analysed and compared with DEXA data. BMD was maintained 1 year after THA in ROIs 3, 4, 5 and 6, whereas BMD decreased in ROIs 1, 2 and 7. FE analysis revealed that equivalent stress in ROIs 3, 4, 5 and 6 was much higher than that in ROIs 1, 2 and 7. A significant correlation was observed between the rate of changes in BMD and equivalent stress. Reduction of equivalent stress may contribute to decrease in BMD in the femur after THA.

Changes in strain patterns after implantation of a short stem with metaphyseal anchorage compared to a standard stem: an experimental study in synthetic bone

Short stem hip arthroplasties with predominantly metaphyseal fixation, such as the METHA® stem (Aesculap, Tuttlingen, Germany), are recommended because they are presumed to allow a more physiologic load transfer and thus a reduction of stress-shielding. However, the hypothesized metaphyseal anchorage associated with the aforementioned benefits still needs to be verified. Therefore, the METHA short stem and the Bicontact® standard stem (Aesculap, Tuttlingen, Germany) were tested biomechanically in synthetic femora while strain gauges monitored their corresponding strain patterns. For the METHA stem, the strains in all tested locations including the region of the calcar (87% of the non-implanted femur) were similar to conditions of synthetic bone without implanted stem. The Bicontact stem showed approximately the level of strain of the non-implanted femur on the lateral and medial aspect in the proximal diaphysis of the femur. On the anterior and posterior aspect of the proximal metaphysis the strains reached averages of 78% and 87% of the non-implanted femur, respectively. This study revealed primary metaphyseal anchorage of the METHA short stem, as opposed to a metaphyseal-diaphyseal anchorage of the Bicontact stem.

Mid-term study of bone remodeling after femoral cemented stem implantation: comparison between DXA and finite element simulation

This five-year prospective study was designed to investigate periprosthetic bone remodeling associated with two cemented stem models, ABG-II (Stryker) and VerSys (Zimmer), randomly implanted in patients older than 75 years. The sample consisted of 64 cases (32, ABG-II; 32, VerSys). Inclusion criterion was diagnosis of osteoarthritis recommended for cemented total hip arthroplasty. Besides clinical study, Finite Element (FE) simulation was used to analyze biomechanical changes caused by hip arthroplasty. Bone Mineral Density (BMD) measurements showed a progressive increase in bone mass throughout the entire follow-up period for both stems, well correlated with FE results except in Gruen zones 4, 5, 6 for ABG-II and in zones 4, 5 for VerSys, denoting that remodeling in those zones does not depend on mechanical factors but rather on biological or physiological ones.

Long-term outcomes of a new model of anatomical hydroxyapatite-coated hip prosthesis

This prospective study was designed to evaluate 196 Anatomique Benoist Giraud (ABG II) total hip arthroplasties which were implanted between September 1999 and December 2000. A minimum 11 years follow up was completed in 183 cases. The bearing surfaces were polyethylene-zirconia in 84 cases, polyethylene-metal in 42 and ceramic-ceramic in 57. Changes in the femoral stem design, in relation to the previous ABG I model, have led to a significant improvement in stress-shielding. Polyethylene wear rate was lower by more than 50% compared with non-crosslinked polyethylene. Excellent and good results were obtained in 90.32% of cases, and implant survival was 98.39% at the end of follow-up.

The cementless anatomic Benoist Girard (ABG) II total hip arthroplasty: a minimum 8-year follow-up study

We have evaluated 90 consecutive primary cementless ABG II total hip replacements. The bearings combined metal-on-polyethylene in 64 hips, and alumina-on-alumina in 26 hips. At the minimum 8-year follow-up, ten patients had died, seven had been lost to follow-up, two had undergone revision of either or both components, and 68 were still alive and had not been revised. With revision for any reason as the endpoint, the cumulative survival rate at 10years was 97.5%±1.7%, and 98.7%±1.3% for the metal-back cup and the femoral component, respectively. No hip showed peri-acetabular osteolysis. The ABG II total hip arthroplasty has demonstrated favourable clinical and radiological outcomes as well as survival in the current series. Further follow-up is needed to confirm these mid-term results.

Stable, dependable fixation of short-stem femoral implants at 5 years

Conventional uncemented femoral implants provide dependable long-term fixation in patients with a wide range of clinical function. However, challenges with proximal-distal femoral mismatch, preservation of bone stock, and minimally invasive approaches have led to exploration into various other implant designs. Short-stem designs focusing on a stable metaphyseal fit have emerged to address these challenges in total hip arthroplasty (THA). The purpose of this study was to present the 5-year clinical and radiographic results of a computed tomography-based, custom-made, metaphyseal-engaging short-stem femoral implant.Sixty-one patients with an average age of 61 years (range, 22-75 years) and average body mass index of 28.9 kg/m(2) (range, 20.3-44.1 kg/m(2)) at follow-up underwent 69 THAs with the metaphyseal-engaging short stem. Clinical performance was evaluated using the Harris Hip Score and Western Ontario and McMaster Universities Arthritis Index score, and radiographs were reviewed for stability and bony ingrowth. Harris Hip Score averaged 55 (range, 20-90) preoperatively and 96 (range, 55-100) postoperatively. Western Ontario and McMaster Universities Arthritis Index score averaged 51 (range, 13-80) preoperatively and 3 (range, 0-35) postoperatively. No cases of subsidence were observed, and no revision surgeries were performed. Bone remodeling was typified by endosteal condensation and cortical hypertrophy in Gruen zones 2, 3, 5, and 6. At 5-year follow-up, the uncemented, metaphyseal-engaging short stem was stable and exhibited proximal bone remodeling closer to the metaphysis than conventional stems. Short-stem, metaphyseal-engaging femoral implants can meet the goals of a successful THA.

Applications of finite element simulation in orthopedic and trauma surgery

Research in different areas of orthopedic and trauma surgery requires a methodology that allows both a more economic approach and the ability to reproduce different situations in an easy way. Simulation models have been introduced recently in bioengineering and could become an essential tool in the study of any physiological unity, regardless of its complexity. The main problem in modeling with finite elements simulation is to achieve an accurate reproduction of the anatomy and a perfect correlation of the different structures, in any region of the human body. Authors have developed a mixed technique, joining the use of a three-dimensional laser scanner Roland Picza captured together with computed tomography (CT) and 3D CT images, to achieve a perfect reproduction of the anatomy. Finite element (FE) simulation lets us know the biomechanical changes that take place after hip prostheses or osteosynthesis implantation and biological responses of bone to biomechanical changes. The simulation models are able to predict changes in bone stress distribution around the implant, so allowing preventing future pathologies. The development of a FE model of lumbar spine is another interesting application of the simulation. The model allows research on the lumbar spine, not only in physiological conditions but also simulating different load conditions, to assess the impact on biomechanics. Different degrees of disc degeneration can also be simulated to determine the impact on adjacent anatomical elements. Finally, FE models may be useful to test different fixation systems, i.e., pedicular screws, interbody devices or rigid fixations compared with the dynamic ones. We have also developed models of lumbar spine and hip joint to predict the occurrence of osteoporotic fractures, based on densitometric determinations and specific biomechanical models, including approaches from damage and fracture mechanics. FE simulations also allow us to predict the behavior of orthopedic splints applied to the correction of deformities, providing the recovering force-displacement and angle-moment curves that characterize the mechanical behavior of the splint in the overall range of movement.

Quantitative CT with finite element analysis: towards a predictive tool for bone remodelling around an uncemented tapered stem

PURPOSE

We used quantitative CT in conjunction with finite element analysis to provide a new tool for assessment of bone quality after total hip arthroplasty in vivo. The hypothesis of this prospective five-year study is that the combination of the two modalities allows 3D patient-specific imaging of cortical and cancellous bone changes and stress shielding.

METHOD

We tested quantitative CT in conjunction with finite elements on a cohort of 29 patients (31 hips) who have been scanned postoperatively and at one year, two years and five years follow-up. The method uses cubic Hermite finite element interpolation for efficient mesh generation directly from qCT datasets. The element Gauss points that are used for the geometric interpolation functions are also used for interpolation of osteodensitometry data.

RESULTS

The study showed changes of bone density suggestive of proximal femur diaphysis load transfer with osteointegration and moderate metaphyseal stress shielding. Our model revealed that cortical bone initially became porous in the greater trochanter, but this phenomenon progressed to the cortex of the lesser trochanter and the posterior aspect of the metaphysis. The diaphyseal area did not experience major change in bone density for either cortical or cancellous bone.

CONCLUSION

The combination of quantitative CT with finite element analysis allows visualization of changes to bone density and architecture. It also provides correlation of bone density/architectural changes with stress patterns enabling the study of the effects of stress shielding on bone remodelling in vivo. This technology can be useful in predicting bone remodeling and the quality of implant fixation using prostheses with different design and/or biomaterials.

Investigation of stress shielding around the Stryker Omnifit and Exeter periprosthetic hip implants using an irreversible thermodynamic-based model

This study investigates stress shielding by predicting bone density around two different implants following total hip arthroplasty using a new thermodynamic-based model for bone remodeling. This model is based on chemical kinetics and irreversible thermodynamics in which bone is treated as a self-organizing system capable of exchanging matter, energy, and entropy with its surroundings. Unlike the previous works in which mechanical loading is regarded as the only stimulus for bone remodeling, this model establishes a coupling between mechanical loading and the chemical reactions involved in the process of bone remodeling. This model is incorporated into the finite element software ANSYS by means of a macro to investigate stress shielding around two different implants: Stryker Omnifit and Exeter periprosthetic hip stems. The results of the simulation showing bone density reductions of 17% in Gruen zone 1 and 27% in Gruen zones 7 around the Omnifit hip stem agree well with dual-energy X-ray absorptiometry (DEXA) measurements reported in the literature. On the other hand, the Exeter implant is found to result in more severe resorption in the proximal femur. This is consistent with clinical studies, which report a higher survivorship rate for HA-coated Omnifit hip stems.

Periprosthetic bone loss after insertion of an uncemented, customized femoral stem and an uncemented anatomical stem. A randomized DXA study with 5-year follow-up

BACKGROUND AND PURPOSE

Customized femoral stems are designed to have a perfect fit and fill in the femur in order to achieve physiological load transfer and minimize stress shielding. Dual-energy X-ray absorptiometry (DXA) is regarded as an accurate method for detection of small alterations in bone mineral density (BMD) around hip prostheses. We present medium-term DXA results from a randomized study comparing a customized and an anatomical femoral stem.

METHODS

100 hips were randomized to receive either the anatomical ABG-I stem or the Unique customized femoral stem, both uncemented. DXA measurements were conducted postoperatively and after 3, 6, 12, 24, 36, and 60 months, and BMD was computed for each of the 7 Gruen zones in the proximal femur.

RESULTS

Results from 87 patients were available for analysis. 78 completed the 5-year follow-up: 35 patients in the ABG group and 43 patients in the Unique group. In both groups, we found the greatest degree of bone loss in the proximal Gruen zones. In zone 1, there was 15% reduction in BMD in the ABG-I group and 14% reduction in the Unique group. In zone 7, the reduction was 28% in the ABG-I group and 27% in the Unique group. The only statistically significant difference between the groups was found in Gruen zone 4, which is distal to the tip of the stem, with 1.6% reduction in BMD in the ABG-I group and 9.7% reduction in the Unique group (p = 0.003).

INTERPRETATION

5-year DXA results showed that because of stress-shielding, proximal bone loss could not be avoided-either for the anatomical ABG-I stem or for the customized Unique stem.

Comparison of different hip prosthesis shapes considering micro-level bone remodeling and stress-shielding criteria using three-dimensional design space topology optimization

Since the late 1980s, computational analysis of total hip arthroplasty (THA) prosthesis components has been completed using macro-level bone remodeling algorithms. The utilization of macro-sized elements requires apparent bone densities to predict cancellous bone strength, thereby, preventing visualization and analysis of realistic trabecular architecture. In this study, we utilized a recently developed structural optimization algorithm, design space optimization (DSO), to perform a micro-level three-dimensional finite element bone remodeling simulation on the human proximal femur pre- and post-THA. The computational simulation facilitated direct performance comparison between two commercially available prosthetic implant stems from Zimmer Inc.: the Alloclassic and the Mayo conservative. The novel micro-level approach allowed the unique ability to visualize the trabecular bone adaption post-operation and to quantify the changes in bone mineral content by region. Stress-shielding and strain energy distribution were also quantified for the immediate post-operation and the stably fixated, post-remodeling conditions. Stress-shielding was highest in the proximal region and remained unchanged post-remodeling; conversely, the mid and distal portions show large increases in stress, suggesting a distal shift in the loadpath. The Mayo design conserves bone mass, while simultaneously reducing the incidence of stress-shielding compared to the Alloclassic, revealing a key benefit of the distinctive geometry. Several important factors for stable fixation, determined in clinical evaluations from the literature, were evident in both designs: high levels of proximal bone loss and distal bone densification. The results suggest this novel computational framework can be utilized for comparative hip prosthesis shape, uniquely considering the post-operation bone remodeling as a design criterion.