Image quality optimization and evaluation of linearly mixed images in dual-source, dual-energy CT

Trauma and 'Whole' Body Computed Tomography: Role, Protocols, Appropriateness, and Evidence to Support its Use and When

Imaging plays a crucial role in the immediate evaluation of the trauma patient, particularly using multi-detector computed tomography (CT), and especially in moderately to severely injured trauma patients. There are specific areas of relative consensus, while other aspects of whole-body computed tomography (WB-CT) use remain controversial and are subject to opinion/debate based on the current literature. Even a few hours of a delayed diagnosis may result in a detrimental outcome for the patient. One must utilize all the tools available to enhance the interpretation of images. It is also important to recognize imaging pitfalls and artifacts to avoid unnecessary intervention.

Visual assessment and quantitative analysis of dual-energy CT virtual non-calcium in imaging diagnosis of multiple myeloma

OBJECTIVE

To evaluate the reliability and diagnostic performance of dual-energy CT virtual non-calcium imaging in diagnosing bone marrow infiltration in multiple myeloma.

MATERIALS AND METHODS

Seventy-two patients with multiple myeloma and ten controls were recruited. Patients received dual-energy CT and MRI while controls underwent dual-energy CT only, covering the cervical, thoracic, and lumbar spine and the pelvis. Virtual non-calcium images were compared with magnetic resonance images for confirmation and pattern classification. Fleiss Kappa analysis assessed consistency between virtual non-calcium and MRI classifications. Inter-observer agreement for virtual non-calcium and CT attenuation values was evaluated using Bland-Altman analysis. Diagnostic performances across various sites were evaluated using analysis of variance and receiver operating characteristic curve analysis.

RESULTS

Dual-energy CT achieved higher consistency in classifying bone marrow infiltration in multiple myeloma than did MRI (kappa = 0.944). In the overall analysis, the mean virtual non-calcium attenuation values in the bone marrow infiltration group (- 28.3 HU; 95% confidence interval (CI), - 32.1, - 24.6) were higher than those in the non-bone marrow infiltration (- 97.5 HU; 95% CI, - 104.7, - 90.3) and control (- 89.1 HU; 95% CI, - 95.1, - 83.1; F = 172.027, P < 0.001) groups. The optimal cutoff values for virtual non-calcium attenuation varied across the overall (- 42.2 HU), cervical spine (- 21.9 HU), thoracic spine (- 42.8 HU), lumbar spine (- 56.9 HU), and pelvis (- 66.3 HU).

CONCLUSION

Dual-energy CT virtual non-calcium imaging and MRI exhibited good consistency in categorising bone marrow infiltration patterns in multiple myeloma. Different virtual non-calcium attenuation value cutoffs should be used to diagnose bone marrow infiltration in various body regions.

Optimizing dual-energy CT technique for iodine-based contrast-to-noise ratio, a theoretical study

BACKGROUND

Dual-energy CT (DECT) systems provide valuable material-specific information by simultaneously acquiring two spectral measurements, resulting in superior image quality and contrast-to-noise ratio (CNR) while reducing radiation exposure and contrast agent usage. The selection of DECT scan parameters, including x-ray tube settings and fluence, is critical for the stability of the reconstruction process and hence the overall image quality.

PURPOSE

The goal of this study is to propose a systematic theoretical method for determining the optimal DECT parameters for minimal noise and maximum CNR in virtual monochromatic images (VMIs) for fixed subject size and total radiation dose.

METHODS

The noise propagation in the process of projection based material estimation from DECT measurements is analyzed. The main components of the study are the mean pixel variances for the sinogram and monochromatic image and the CNR, which were shown to depend on the Jacobian matrix of the sinograms-to-DECT measurements map. Analytic estimates for the mean sinogram and monochromatic image pixel variances and the CNR as functions of tube potentials, fluence, and VMI energy are derived, and then used in a virtual phantom experiment as an objective function for optimizing the tube settings and VMI energy to minimize the image noise and maximize the CNR.

RESULTS

It was shown that DECT measurements corresponding to kV settings that maximize the square of Jacobian determinant values over a domain of interest lead to improved stability of basis material reconstructions. Instances of non-uniqueness in DECT were addressed, focusing on scenarios where the Jacobian determinant becomes zero within the domain of interest despite significant spectral separation. The presence of non-uniqueness can lead to singular solutions during the inversion of sinograms-to-DECT measurements, underscoring the importance of considering uniqueness properties in parameter selection. Additionally, the optimal VMI energy and tube potentials for maximal CNR was determined. When the x-ray beam filter material was fixed at 2 mm of aluminum and the photon fluence for low and high kV scans were considered equal, the tube potential pair of 60/120 kV led to the maximal iodine CNR in the VMI at 53 keV.

CONCLUSIONS

Optimizing DECT scan parameters to maximize the CNR can be done in a systematic way. Also, choosing the parameters that maximize the Jacobian determinant over the set of expected line integrals leads to more stable reconstructions due to the reduced amplification of the measurement noise. Since the values of the Jacobian determinant depend strongly on the imaging task, careful consideration of all of the relevant factors is needed when implementing the proposed framework.

Observing the fragmentation of two expanding bullet types and a full metal-jacketed bullet with computed tomography-a forensic ballistics case study

Computed tomography (CT) may have a crucial role in the forensic documentation and analysis of firearm injuries. The aim of this forensic ballistics case study was to explore whether two types of expanding bullets and a full metal-jacketed bullet could be differentiated by inspecting bullet fragments and fragmentation pattern in CT. Three types of .30 caliber bullets (full metal-jacketed Norma Jaktmatch, expanding full-copper Norma Ecostrike, and expanding soft-point Norma Oryx) were test fired from a distance of 5 m to blocks of 10% ballistic gelatine. CT scans of the blocks were obtained with clinical equipment and metal artifact reduction. Radiopaque fragments were identified and fragmentation parameters were obtained from the scans (total number of fragments, maximum diameter of the largest fragment, distance between entrance and the closest fragment, length of the fragment cloud, and maximum diameters of the fragment cloud). The fragmentation patterns were additionally visualized by means of 3D reconstruction. In CT, the bullet types differed in several fragmentation parameters. While the expanding full-copper bullet Ecostrike left behind only a single fragment near the end of the bullet channel, the soft-point Oryx had hundreds of fragments deposited throughout the channel. For both expanding bullets Ecostrike and Oryx, the fragments were clearly smaller than those left behind by the full metal-jacketed Jaktmatch. This was surprising as the full metal-jacketed bullet was expected to remain intact. The fragment cloud of Jaktmatch had similar mediolateral and superoinferior diameters to that of Oryx; however, fragments were deposited in the second half of the gelatine block, and not throughout the block. This case study provides a basis and potential methodology for further experiments. The findings are expected to benefit forensic practitioners with limited background information on gunshot injury cases, for example, those that involve several potential firearms or atypical gunshot wounds. The findings may prove beneficial for both human and wildlife forensics.

Diagnostic accuracy of dual-energy computed tomography in the diagnosis of neurological complications after endovascular treatment of acute ischaemic stroke: a systematic review and meta-analysis

OBJECTIVES

To investigate dual-energy computed tomography's (DECT) diagnostic performance in detecting neurological complications following endovascular therapy (EVT) of acute ischaemic stroke (AIS).

METHODS

We performed the literature search using Web of Science, Scopus, PubMed, EBSCO, and Science Direct databases for published related studies. The selected studies estimated the validity of DECT in the detection of neurological complications after EVT for AIS. Study quality assessment was performed utilizing the Quality of Diagnostic Accuracy Studies-2 Tool. Our meta-analysis calculated the pooled sensitivity, negative likelihood ratio, specificity, and positive likelihood ratio for each detected complication. The summary receiver operating characteristics (sROC) curve was utilized to estimate the area under the curve (AUC).

RESULTS

Of 22 studies, 21 were included in the quantitative synthesis. In the detection of intracerebral haemorrhage (ICH), DECT pooled overall sensitivity and specificity were 69.9% (95% CI, 44.5%-86.8%) and 100% (95% CI, 92.1%-100%); whereas, in the detection of ischaemia, they were 85.9% (95% CI, 80.4%-90%) and 90.7% (95% CI, 87%-93.5%), respectively. On the sROC curve, AUC values of 0.954 and 0.952 were recorded for the detection of ICH and ischaemia, respectively.

CONCLUSIONS

DECT demonstrated high accuracy and specificity in the detection of neurological complications post-endovascular treatment of AIS. However, further prospective studies with a standardized reference test and a larger sample size are recommended to support these findings.

ADVANCES IN KNOWLEDGE

DECT is a rapid and valid imaging tool for the prediction of ICH and cerebral ischaemia after the EVT of AIS.

Reduced versus standard dose contrast volume for contrast-enhanced abdominal CT in overweight and obese patients using photon counting detector technology vs. second-generation dual-source energy integrating detector CT

PURPOSE

To compare image quality of contrast-enhanced abdominal-CT using 1st-generation Dual Source Photon-Counting Detector CT (DS-PCD-CT) versus 2nd-generation Dual-Source Energy Integrating-Detector CT (DS-EID-CT) in patients with BMI ≥ 25, applying two different contrast agent volumes, vendor proposed protocols and different virtual monoenergetic images (VMI).

METHOD

68 overweight (BMI ≥ 25 kgm2) patients (median age: 65 years; median BMI 33.3 kgm2) who underwent clinically indicated, portal-venous contrast-enhanced abdominal-CT on a commercially available 1st-generation DS-PCD-CT were prospectively included if they already have had a pre-exam on 2nd-generation DS-EID-CT using a standardized exam protocol. Obesity were defined by BMI-calculation (overweight: 25-29.9, obesity grade I: 30-34.9; obesity grade II: 35-39.9; obesity grade III: > 40) and by the absolute weight value. Body weight adapted contrast volume (targeted volume of 1.2 mL/kg for the 1st study and 0.8 mL/kg for the 2nd study) was applied in both groups. Dual Energy mode was used for both the DS-PCD-CT and the DS-EID-CT. Polychromatic images and VMI (40 keV and 70 keV) were reconstructed for both the DS-EID-CT and the DS-PCD-CT data (termed T3D). Two radiologists assessed subjective image quality using a 5-point Likert-scale. Each reader drew ROIs within parenchymatous organs and vascular structures to analyze image noise, contrast-to-noise ratio (CNR) and signal-to-noise ratio (SNR).

RESULTS

Median time interval between scans was 12 months (Min: 6 months; Max: 36 months). BMI classification included overweight (n = 10, 14.7 %), obesity grade I (n = 38, 55.9 %), grade II (n = 13, 19.1 %) and grade III (n = 7, 10.3 %). The SNR achieved with DS-PCD-CT at QIR level 3was 12.61 vs. 11.47 (QIR 2) vs. 10.53 (DS-EID-CT), irrespective of parenchymatous organs. For vessels, the SNR were 16.73 vs. 14.20 (QIR 2) vs. 12.07 (DS-EID-CT). Moreover, the obtained median noise at QIR level 3 was as low as that of the DS-EID-CT (8.65 vs. 8.65). Both radiologists rated the image quality higher for DS-PCD-CT data sets (p < 0.05). The highest CNR was achieved at 40 keV for both scanners. T3D demonstrated significantly higher SNR and lower noise level compared to 40 keV and 70 keV. Median CTDIvol and DLP values for DS-PCD-CT and DS-EID-CT were 10.90 mGy (IQR: 9.31 - 12.50 mGy) vs. 16.55 mGy (IQR: 15.45 - 18.17 mGy) and 589.50 mGy * cm (IQR: 498.50 - 708.25 mGy * cm) vs. 848.75 mGy * cm (IQR: 753.43 - 969.58 mGy * cm) (p < 0.001).

CONCLUSION

Image quality can be maintained while significantly reducing the contrast volume and the radiation dose (27% and 34% lower DLP and 31% lower CDTIvol) for abdominal contrast-enhanced CT using a 1st-generation DS-PCD-CT. Moreover, polychromatic reconstruction T3D on a DS-PCD-CT enables sufficient diagnostic image quality for oncological imaging.

Virtual monoenergetic imaging in photon-counting CT of the head and neck

PURPOSE

Advantages of virtual monoenergetic images (VMI) have been reported for dual energy CT of the head and neck, and more recently VMIs derived from photon-counting (PCCT) angiography of the head and neck. We report image quality metrics of VMI in a PCCT angiography dataset, expanding the anatomical regions evaluated and extending observer-based qualitative methods further than previously reported.

METHODS

In a prospective study, asymptomatic subjects underwent contrast enhanced PCCT of the head and neck using an investigational scanner. Image sets of low, high, and full spectrum (Threshold-1) energies; linear mix of low and high energies (Mix); and 23 VMIs (40-150 keV, 5 keV increments) were generated. In 8 anatomical locations, SNR and radiologists' preferences for VMI energy levels were measured using a forced-choice rank method (4 observers) and ratings of image quality using visual grading characteristic (VGC) analysis (2 observers) comparing VMI to Mix and Threshold-1 images.

RESULTS

Fifteen subjects were included (7 men, 8 women, mean 57 years, range 46-75). Among all VMIs, SNRs varied by anatomic location. The highest SNRs were observed in VMIs. Radiologists preferred 50-60 keV VMIs for vascular structures and 75-85 keV for all other structures. Cumulative ratings of image quality averaged across all locations were higher for VMIs with areas under the curve of VMI vs Mix and VMI vs Threshold-1 of 0.67 and 0.68 for the first reader and 0.72 and 0.76 for the second, respectively.

CONCLUSION

Preferred keV level and quality ratings of VMI compared to mixed and Threshold-1 images varied by anatomical location.

Radiation Dose Reduction in Contrast-Enhanced Abdominal CT: Comparison of Photon-Counting Detector CT with 2nd Generation Dual-Source Dual-Energy CT in an oncologic cohort

RATIONAL AND OBJECTIVES

Comparison of radiation dose and image quality in routine abdominal and pelvic contrast-enhanced computed tomography (CECT) between a photon-counting detector CT (PCD-CT) and a dual energy dual source CT (DSCT).

MATERIALS AND METHODS

70 oncologic patients (mean age 66 ± 12 years, 29 females) were prospectively enrolled between November 2021 and February 2022. Abdominal CECT were clinically indicated and performed first on a 2nd-generation DSCT and at follow-up on a 1st-generation dual-source PCD-CT. The same contrast media (Imeron 350, Bracco imaging) and pump protocol was used for both scans. For both scanners, polychromatic images were reconstructed with 3mm slice thickness and comparable kernel (I30f[DSCT] and Br40f[PCD-CT]); for PCD-CT data from all counted events above the lowest energy threshold at 20 keV ("T3D") were used. Results were compared in terms of radiation dose metrics of CT dose index (CTDIvol), dose length product (DLP) and size-specific dose estimation (SSDE), objective and subjective measurements of image quality were scored by two emergency radiologists including lesion conspicuity.

RESULTS

Median time interval between the scans was 4 months (IQR: 3-6). CNRvessel and SNRvessel of T3D reconstructions from PCD-CT were significantly higher than those of DSCT (all, p < 0.05). Qualitative image noise analysis from PCD-CT and DSCT yielded a mean of 4 each. Lesion conspicuity was rated significantly higher in PCD-CT (Q3 strength) compared to DSCT images. CTDI, DLP and SSDE mean values for PCD-CT and DSCT were 7.98 ± 2.56 mGy vs. 14.11 ± 2.92 mGy, 393.13 ± 153.55 mGy*cm vs. 693.61 ± 185.76 mGy*cm and 9.98 ± 2.41 vs. 14.63 ± 1.63, respectively, translating to a dose reduction of around 32% (SSDE).

CONCLUSION

PCD-CT enables oncologic abdominal CT with a significantly reduced dose while keeping image quality similar to 2nd-generation DSCT.

A Novel Dual-Energy CT Method for Detection and Differentiation of Intracerebral Hemorrhage From Contrast Extravasation in Stroke Patients After Endovascular Thrombectomy : Feasibility and First Results

PURPOSE

Dual-energy computed tomography (DECT) has been shown to be able to differentiate between intracranial hemorrhage (ICH) and extravasation of iodinated contrast media (contrast staining [CS]). TwinSpiral DECT is a recently introduced technique, which allows image acquisition at two different energy levels in two consecutive spiral scans. The aim of this study was to evaluate the feasibility and accuracy of TwinSpiral DECT to distinguish between ICH and CS after endovascular thrombectomy (EVT) in patients with acute ischemic stroke.

METHODS

This retrospective single-center study conducted between November 2019 and July 2020 included non-contrast TwinSpiral DECT scans (tube voltages 80 and 150Sn kVp) of 39 ischemic stroke patients (18 females, 21 males, mean age 69 ± 11 years) within 48-72 h after endovascular thrombectomy. Parenchymal hyperdensity was assessed for the presence of ICH or/and CS by two board certified and fellowship-trained, blinded and independent neuroradiologists using standard mixed images and virtual non-contrast (VNC) images with corresponding iodine maps from TwinSpiral DECT. Follow-up examinations (FU; CT or MRI) were used as a standard of reference. Sensitivity, specificity, and accuracy for the detection of ICH as well as the inter-reader agreement were calculated.

RESULTS

Parenchymal hyperdensities were detected in 17/39 (44%) patients. Using DECT, they were classified by both readers as ICH in 9 (53%), CS in 8 (47%), and mixture of both in 6 (35%) cases with excellent agreement (κ = 0.81, P < 0.0001). The sensitivity, specificity, and accuracy for the detection of ICH in DECT was 90% (95% confidence interval [CI]: 84-96%), 100% (95% CI 94-100%) and 95% (95% CI 89-100%), and in mixed images 90% (95% CI 84-96%), 86% (95% CI 80-92%) and 88% (95% CI 82-94%), respectively. Inter-reader agreement for detecting ICH on DECT compared to the mixed images was κ = 1.00 (P < 0.0001) vs. κ = 0.51 (P = 0.034).

CONCLUSION

TwinSpiral DECT demonstrates high accuracy and excellent specificity for differentiating ICH from CS in patients after mechanical thrombectomy due to acute ischemic stroke, and improves inter-reader agreement for detecting ICH compared to the standard mixed images.

Dual-energy micro-focus computed tomography based on the energy-angle correlation of inverse Compton scattering source

BACKGROUND

Inverse Compton scattering (ICS) source can produce quasi-monoenergetic micro-focus X-rays ranging from keV to MeV level, with potential applications in the field of high-resolution computed tomography (CT) imaging. ICS source has an energy-angle correlated feature that lower photon energy is obtained at larger emission angle, thus different photon energies are inherently contained in each ICS pulse, which is especially advantageous for dual- or multi-energy CT imaging.

OBJECTIVE

This study proposes a dual-energy micro-focus CT scheme based on the energy-angle correlation of ICS source and tests its function using numerical simulations.

METHODS

In this scheme, high- and low-energy regions are chosen over the angular direction of each ICS pulse, and dual-energy projections of the object are obtained by an angularly-splicing scanning method. The field-of-view (FOV) of ICS source is extended simultaneously through this scanning method, thus the scale of the imaging system can be efficiently reduced. A dedicated dual-energy CT algorithm is developed to reconstruct the monoenergetic attenuation coefficients, electron density, and effective atomic number distributions of the object.

RESULTS

A test object composed of different materials (carbon, aluminium, titanium, iron and copper) and line pairs with different widths (15/24/39/60 μm) is imaged by the proposed dual-energy CT scheme using numerical simulations, and high-fidelity monoenergetic attenuation coefficient, electron density, and effective atomic number distributions are obtained. All the line pairs are well identified, and the contrast ratio of the 15 μm lines is 22%, showing good accordance with the theoretical predictions.

CONCLUSIONS

The proposed dual-energy CT scheme can reconstruct fine inner structures and material compositions of the object simultaneously, opening a new possibility for the application of ICS source in the field of non-destructive testing.

Evaluation of the quantitative performance of non-enhanced dual-energy CT X-map in detecting acute ischemic brain stroke: A model observer study using computer simulation

PURPOSE

A simulation study was performed to evaluate the quantitative performance of X-map images-derived from non-enhanced (NE) dual-energy computed tomography (DECT)-in detecting acute ischemic stroke (AIS) compared with that of NE-DECT mixed images.

METHODS

A virtual phantom, 150 mm in diameter, filled with tissues comprising various gray- and white-matter proportions was used to generate pairs of NE-head images at 80 kV and Sn150 kV at three dose levels (20, 40, and 60 mGy). The phantom included an inserted low-contrast object, 15 mm in diameter, with four densities (0%, 5%, 10%, and 15%) mimicking ischemic edema. Mixed and X-map images were generated from these sets of images and compared in terms of detectability of ischemic edema using a channelized Hotelling observer (CHO). The area under the curve (AUC) of the receiver operating characteristic that generated CHO for each condition was used as a figure of merit.

RESULTS

The AUCs of X-map images were always significantly higher than those of mixed images (P < 0.001). The improvement in AUC for X-map images compared with that for mixed images at edema densities was 9.2%-12.6% at 20 mGy, 10.1%-17.7% at 40 mGy, and 14.0%-19.4% at 60 mGy. At any edema density, X-map images at 20 mGy resulted in higher AUCs than mixed images acquired at any other dose level (P < 0.001), which corresponded to a 66% dose reduction on X-map images.

CONCLUSIONS

The simulation study confirmed that NE-DECT X-map images have superior capability of detecting AIS than NE-DECT mixed images.

Value of low-keV virtual monoenergetic plus dual-energy computed tomographic imaging for detection of acute pulmonary embolism

Objective

To compare diagnostic values between the 40 keV virtual monoenergetic plus (40 keV VMI+) dual source dual energy computed tomography (DSDECT) pulmonary angiography images and the standard mixed (90 and 150 kV) images for the detection of acute pulmonary embolism (PE).

Methods

Chest DSDECTs of 64 patients who were suspected of having acute PE were retrospectively reviewed by two independent reviewers. The assessments of acute PE of all patients on a per-location basis were compared between the 40 keV VMI+ and the standard mixed datasets (reference standard) with a two-week interval.

Results

This study consisted of 64 patients (33 women and 31 men; mean age, 60.2 years; range 18–90 years), with a total of 512 locations. The interobserver agreement (Kappa) for detection of acute PE using the 40 keV VMI+ images and the standard mixed CT images were 0.7478 and 0.8750 respectively. The area under receiver operating characteristics (AuROC) for diagnosis of acute PE using the 40 keV VMI+ was 0.882. Four locations (0.78%) revealed a false negative result. Hypodense filling defects were identified in twelve locations (1.95%) in the 40 keV VMI+ images but had been interpreted as a negative study in the standard mixed CT images. The repeated reviews revealed that each location contained a hypodense filling defect but was overlooked on the standard mixed CT images.

Conclusions

Low-energy VMI + DSDECT images have beneficial in improving the diagnostic value of acute PE in doubtful or disregarded standard mixed images.

Spectral computed tomography with inorganic nanomaterials: State-of-the-art

Recently, spectral computed tomography (CT) technology has received great interest in the field of radiology. Spectral CT imaging utilizes the distinct, energy-dependent X-ray absorption properties of substances in order to provide additional imaging information. Dual-energy CT and multi-energy CT (Spectral CT) are capable of constructing monochromatic energy images, material separation images, energy spectrum curves, constructing effective atomic number maps, and more. However, poor contrast, due to neighboring X-ray attenuation of organs and tissues, is still a challenge to spectral CT. Hence, contrast agents (CAs) are applied for better differentiation of a given region of interest (ROI). Currently, many different kinds of inorganic nanoparticulate CAs for spectral CT have been developed due to the limitations of clinical iodine (I)-based contrast media, leading to the conclusion that inorganic nanomedicine applied to spectral CT will be a powerful collaboration both in basic research and in clinics. In this review, the underlying principles and types of spectral CT techniques are discussed, and some evolving clinical diagnosis applications of spectral CT techniques are introduced. In particular, recent developments in inorganic CAs used for spectral CT are summarized. Finally, the challenges and future developments of inorganic nanomedicine in spectral CT are briefly discussed.

Detection of Early Ischemic Changes with Virtual Noncontrast Dual-Energy CT in Acute Ischemic Stroke: A Noninferiority Analysis

BACKGROUND AND PURPOSE

Dual-energy virtual NCCT has the potential to replace conventional NCCT to detect early ischemic changes in acute ischemic stroke. In this study, we evaluated whether virtual NCCT is noninferior compared with standard linearly blended NCCT, a surrogate of conventional NCCT, regarding the detection of early ischemic changes with ASPECTS.

MATERIALS AND METHODS

Adult patients who presented with suspected acute ischemic stroke and who underwent dual-energy NCCT and CTA and brain MR imaging within 48 hours were included. Standard linearly blended images were reconstructed to match a conventional NCCT. Virtual NCCT images were reconstructed from CTA. ASPECTS was evaluated on conventional NCCT, virtual NCCT, and DWI, which served as the reference standard. Agreement between CT assessments and the reference standard was evaluated with the Lin concordance correlation coefficient. Noninferiority was assessed with bootstrapped estimates of the differences in ASPECTS between conventional and virtual NCCT with 95% CIs.

RESULTS

Of the 193 included patients, 100 patients (52%) had ischemia on DWI. Compared with the reference standard, the ASPECTS concordance correlation coefficient for conventional and virtual NCCT was 0.23 (95% CI, 0.15-0.32) and 0.44 (95% CI, 0.33-0.53), respectively. The difference in the concordance correlation coefficient between virtual and conventional NCCT was 0.20 (95% CI, 0.01-0.39) and did not cross the prespecified noninferiority margin of -0.10.

CONCLUSIONS

Dual-energy virtual NCCT is noninferior compared with conventional NCCT for the detection of early ischemic changes with ASPECTS.

Life-threatening perforating brain injury by a rusty iron rod - A case report

Background

When an object traverses through the cranium leaving behind both an entry and exit wound, it is called perforating brain injury. Perforating open brain injury is rare. A paucity of published literature on such cases and a lack of a standard management protocol pose significant challenges in managing such cases.

Case Description

We present a case of a 24-year-old man who worked as a carpenter at the construction site. He slipped while working and fell from a height of 13 feet onto a rusty, vertically placed 3 feet iron rod located on the ground. Iron rod entered his body from the right upper chest, came out from the neck, and again re-entered through the right upper neck medial to the angle of the mandible and finally came out from the posterosuperior surface of the right side of the head. He presented to the emergency department in a conscious state, but his voice was heavy and slow-paced, and he showed signs of lower cranial nerve palsy on the right side. He underwent numerous radiological investigations. The iron rod was removed in the operation theater under strict aseptic precautions. On day 7 after surgery, he developed right lobar pneumonia, and on day 21, he developed an altered sensorium, followed by a loss of consciousness. He did not regain consciousness and, unfortunately, succumbed after 30 days of sustaining the injuries.

Conclusion

Perforating open brain injuries are rare, especially in civilian society, and are usually associated with significant morbidity and mortality. Due to a lack of standard guidelines for managing such severe injuries and limited knowledge, many patients with these injuries do not survive. Although each case presents differently, certain management principles must be followed.

Dependence of Water-equivalent Diameter and Size-specific Dose Estimates on CT Tube Potential

Background The size-specific dose estimate (SSDE) is a patient-focused CT dose metric. However, published size-dependent conversion factors (f_size) used to calculate SSDE were determined primarily by using phantoms; only eight to 15 patient data sets were used, all at 120 kV. Purpose To determine the effect of different tube potentials on the water-equivalent diameter (WED) and SSDE for patient CT scans of the head, chest, and abdomen. Materials and Methods This retrospective study used 250 noncontrast CT scans acquired between March 2013 and June 2017. Bony structures were segmented, and their CT numbers were modified to reflect bone attenuation at 70, 90, 110, 130, and 150 kV. Soft-tissue CT numbers were unchanged because of negligible energy dependence. f_size was measured in anthropomorphic phantoms for each tube potential and fit to an exponential function. WED and SSDE were determined for each patient at all tube potentials, regression analysis was performed relative to the WED and SSDE at 120 kV, and mean differences relative to 120 kV were calculated. Results In 250 patients (median age, 21.5 years; interquartile range, 44 years; 130 women), WED for all tube potentials was linearly related to the WED at 120 kV in all body regions (R² = 0.995-1.000). The effect of tube potential on WED was negligible for torso examinations (Cohen d < 0.05). In the head, a medium effect size was observed at 70 kV; however, the mean absolute difference in WED was small (-0.49 cm ± 0.08 [standard deviation]; P < .001). For commonly used combinations of tube potential and patient size, the mean differences in SSDE at alternative tube potentials relative to SSDE at 120 kV were less than 5%. Conclusion At noncontrast CT, published size-dependent conversion factors accurately determined size-specific dose estimates on 250 patient scans at five tube potentials other than 120 kV. © RSNA, 2022 Online supplemental material is available for this article. See also the editorial by Boone in this issue.

Image quality enhancement of CT hepatic portal venography using dual energy blending with computer determined parameters

BACKGROUND

Previous studies have shown that using some post-processing methods, such as nonlinear-blending and linear blending techniques, has potential to improve dual-energy computed (DECT) image quality.

OBJECTIVE

To improve DECT image quality of hepatic portal venography (CTPV) using a new non-linear blending method with computer-determined parameters, and to compare the results to additional linear and non-linear blending techniques.

METHODS

DECT images of 60 patients who were clinically diagnosed with liver cirrhosis were selected and studied. Dual-energy scanning (80 kVp and Sn140 kVp) of CTPV was utilized in the portal venous phase through a dual-source CT scanner. For image processing, four protocols were utilized including linear blending with a weighing factor of 0.3 (protocol A) and 1.0 (protocol B), non-linear blending with fixed blending width of 200 HU and set blending center of 150HU (protocol C), and computer-based blending (protocol D). Several image quality indicators, including signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR) and contrast of hepatic portal vein and hepatic parenchyma, were evaluated using the paired-sample t-test. A 5-grade scale scoring system was also utilized for subjective analysis.

RESULTS

SNR of protocols A-D were 9.1±2.1, 12.1±3.0, 11.6±2.8 and 14.4±3.2, respectively. CNR of protocols A-D were 4.6±1.3, 8.0±2.3, 7.0±2.0 and 9.8±2.4, respectively. The contrast of protocols A-D were 37.7±11.6, 91.9±21.0, 66.2±19.0 and 107.7±21.3, respectively. The differences between protocol D and other three protocols were significant (P < 0.01). In subjective evaluation, the modes of protocols A, B, C, and D were rated poor, good, generally acceptable, and excellent, respectively.

CONCLUSION

The non-linear blending technique of protocol D with computer-determined blending parameters can help improve imaging quality of CTPV and contribute to a diagnosis of liver disease.

Spectral CT using a fine grid structure and varying x-ray incidence angle

PURPOSE

Interest in spectral computed tomography (CT) for diagnostics and therapy evaluation has been growing. Data acquisitions with distinct spectral sensitivities provide the ability to discriminate multiple materials, quantitative density estimates, and reduced artifacts due to energy dependencies. We introduce a novel spectral CT concept that includes a fine-pitch grid structure for prefiltration of the x-ray beam.

METHODS

We develop physical models for grid designs and illustrate the basic operating principles wherein small angulations of the incident x rays results significant filtration and spectral shaping of the beam. We fabricate a prototype grid with tungsten lamellae. We compare x-ray spectra induced by this filter as a function of incidence angle in both simulation students and in physical measurements. The grid is also integrated onto a CT test bench where we scanned an iodinated phantom with clinically relevant concentrations (5, 10, 20, and 50 mgI/mL) to demonstrate the ability to perform spectral CT acquisitions and material decomposition.

RESULTS

X-ray spectrometer measurements reveal diverse and controllable spectral shaping with small angle changes that are in agreement with simulation studies. Critical angles where the characteristics of the induced spectrum changes dramatically are identified. Reconstructions of projection data for two angulations separated by 2° was reconstructed and material decomposition into iodine and water images shows good agreement with the known iodine concentrations.

CONCLUSIONS

This work demonstrates the feasibility of the grid-based approach to enable spectral CT data acquisitions and accurate material decompositions. On-going and future studies will investigate the potential of this novel concept as a relatively simple upgrade to standard energy-integrating CT.

Photon-Counting Computed Tomography for Coronary Stent Imaging: In Vitro Evaluation of 28 Coronary Stents

OBJECTIVES

The aim of this study was to assess in-stent lumen visibility and quantitative image characteristics of different coronary stents using a novel photon-counting detector (PCD) computed tomography (CT) system in comparison to a state-of-the-art energy-integrating detector (EID) CT scanner.

MATERIALS AND METHODS

In this in vitro phantom study, 28 different coronary stents ranging from 2.25 to 4.5 mm lumen diameter were expanded into plastic tubes filled with contrast agent. Stent-containing plastic tubes were positioned in a custom-made emulsion-filled phantom, which was inserted into an anthropomorphic phantom simulating a medium-sized patient. Computed tomography scans were acquired parallel to the scanners' z axis using a novel cadmium telluride-based PCD CT system (SOMATOM CountPlus; Siemens Healthcare GmbH, Forchheim Germany), operating in 2 different modes (standard-resolution mode [SR] and ultra-high-resolution [UHR] mode), and a latest generation dual-source EID CT system (SOMATOM Force; Siemens Healthcare GmbH, Forchheim). CTDIvol-matched images were reconstructed with comparable convolution kernels and using the same reconstruction parameters. In-stent lumen visibility (in %), increase in in-stent attenuation (expressed as Δ in-stent CT attenuation), and image noise (in Hounsfield unit) were manually measured. Parts of the image analysis (in-stent lumen visibility) were additionally performed in an automated way. Differences were tested using Wilcoxon signed rank test.

RESULTS

The best in-stent lumen visibility was achieved with the PCD-UHR mode and the lowest noise levels with the PCD-SR mode. The median in-stent lumen visibility was significantly higher (P < 0.001) with PCD (SR, 66.7%; interquartile range [IQR], 63.3-72.3; UHR, 68.9%; IQR, 64.4-74.4) compared with EID (65.4%; IQR, 62.2-70.4). The Δ in-stent CT attenuation was significantly lower for PCD in both SR (78 HU; IQR, 46-108; P = 0.024) and UHR (85 HU; IQR, 59-113; P = 0.006) compared with EID (108 HU; IQR, 85-126). Image noise was significantly lower (P < 0.001) for PCD-SR (21 HU; IQR, 21-21) compared with EID images (25 HU; IQR, 24-25.0).

CONCLUSIONS

The PCD provides superior in-stent lumen visibility and quantitative image characteristics when compared with conventional EID.

ASPECTS estimation using dual-energy CTA-derived virtual non-contrast in large vessel occlusion acute ischemic stroke: a dose reduction opportunity for patients undergoing repeat CT?

PURPOSE

Recent studies have shown the feasibility of dual-energy CT (DECT) virtual non-contrast (VNC) for determining infarct extent. In this study, patients presenting with large-vessel occlusion (LVO) acute ischemic stroke (AIS), we assess whether ASPECTS on DECTA-VNC differs from non-contrast CT (NCCT).

METHODS

After IRB approval, LVO-AIS patients undergoing NCCT and DECTA between October 2016 and September 2018 were retrospectively reviewed. DECTA-VNC images were derived using Syngo.via (Siemens, Erlangen, Germany). ASPECTS was scored by two blinded neuroradiologists. Square-weighted kappa statistic, diagnostic performance, Wilcoxon signed-rank tests between groups, and CT doses were calculated.

RESULTS

Fifty-one patients met inclusion criteria, with median age of 76 (IQR 67-82); 26/51 (51%) were female. Median time between last-known-well and CT was 120 min (IQR 60-252). DECTA-VNC ASPECTS score differed by ≤ 1 from consensus NCCT in 49/51 (96%) patients for reader 1 and in 46/51 (90%) for reader 2. ASPECTS on DECTA-SI and consensus NCCT differed by ≤ 1 in 45/51 (88%) for both readers. On a per ASPECTS-region basis, DECTA-VNC had 87% sensitivity, 95% specificity, 0.82% PPV, and 0.96% NPV. ASPECTS inter-rater agreement was highest for DECTA-VNC (κ = 0.71), DECTA-SI (κ = 0.48), and NCCT (κ = 0.40). NCCT median CTDIvol was 63.7 mGy (IQR 60.7-67.2); DLP was 1060.0 mGy·cm (IQR 981.0-1151.5). DECTA-VNC dose was lower: median CTDIvol was 20.9 mGy (IQR 19.8-22.2); DLP was 804.1 (IQR 691.6-869.4), p < 0.0001.

CONCLUSION

DECTA-derived VNC yielded similar ASPECTS scores as NCCT and is therefore non-inferior in early ischemia-related low attenuation edema/infarct detection in acute LVO-AIS patients. Further evaluation of the role of DECTA-VNC in AIS imaging is warranted.

Threshold-dependent iodine imaging and spectral separation in a whole-body photon-counting CT system

OBJECTIVE

To evaluate the dual-energy (DE) performance and spectral separation with respect to iodine imaging in a photon-counting CT (PCCT) and compare it to dual-source CT (DSCT) DE imaging.

METHODS

A semi-anthropomorphic phantom extendable with fat rings equipped with iodine vials is measured in an experimental PCCT. The system comprises a PC detector with two energy bins (20 keV, T) and (T, eU) with threshold T and tube voltage U. Measurements using the PCCT are performed at all available tube voltages (80 to 140 kV) and threshold settings (50-90 keV). Further measurements are performed using a conventional energy-integrating DSCT. Spectral separation is quantified as the relative contrast media ratio R between the energy bins and low/high images. Image noise and dose-normalized contrast-to-noise ratio (CNRD) are evaluated in resulting iodine images. All results are validated in a post-mortem angiography study.

RESULTS

R of the PC detector varies between 1.2 and 2.6 and increases with higher thresholds and higher tube voltage. Reference R of the EI DSCT is found as 2.20 on average overall phantoms. Maximum CNRD in iodine images is found for T = 60/65/70/70 keV for 80/100/120/140 kV. The highest CNRD of the PCCT is obtained using 140 kV and is decreasing with decreasing tube voltage. All results could be confirmed in the post-mortem angiography study.

CONCLUSION

Intrinsically acquired DE data are able to provide iodine images similar to conventional DSCT. However, PCCT thresholds should be chosen with respect to tube voltage to maximize image quality in retrospectively derived image sets.

KEY POINTS

• Photon-counting CT allows for the computation of iodine images with similar quality compared to conventional dual-source dual-energy CT. • Thresholds should be chosen as a function of the tube voltage to maximize iodine contrast-to-noise ratio in derived image sets. • Image quality of retrospectively computed image sets can be maximized using optimized threshold settings.

A Novel Low-Dose Dual-Energy Imaging Method for a Fast-Rotating Gantry-Type CT Scanner

CT scan by use of a beam-filter placed between the x-ray source and the patient allows a single-scan low-dose dual-energy imaging with a minimal hardware modification to the existing CT systems. We have earlier demonstrated the feasibility of such imaging method with a multi-slit beam-filter reciprocating along the direction perpendicular to the CT rotation axis in a cone-beam CT system. However, such method would face mechanical challenges when the beam-filter is supposed to cooperate with a fast-rotating gantry in a diagnostic CT system. In this work, we propose a new scanning method and associated image reconstruction algorithm that can overcome these challenges. We propose to slide a beam-filter that has multi-slit structure with its slits being at a slanted angle with the CT gantry rotation axis during a scan. A streaky pattern would show up in the sinogram domain as a result. Using a notch filter in the Fourier domain of the sinogram, we removed the streaks and reconstructed an image by use of the filtered-backprojection algorithm. The remaining image artifacts were suppressed by applying l₀ norm based smoothing. Using this image as a prior, we have reconstructed low- and high-energy CT images in the iterative reconstruction framework. An image-based material decomposition then followed. We conducted a simulation study to test its feasibility using the XCAT phantom and also an experimental study using the Catphan phantom, a head phantom, an iodine-solution phantom, and a monkey in anesthesia, and showed its successful performance in image reconstruction and in material decomposition.

Dual-Energy Computed Tomography of the Liver: Uses in Clinical Practices and Applications

Dual-energy computed tomography (DECT) is an imaging technique based on data acquisition at two different energy settings. Recent advances in CT have allowed data acquisitions and simultaneous analyses of X-rays at two energy levels, and have resulted in novel developments in the field of abdominal imaging. The use of low and high X-ray tube voltages in DECT provide fused images that improve the detection of liver tumors owing to the higher contrast-to-noise ratio (CNR) of the tumor compared with the liver. The use of contrast agents in CT scanning improves image quality by enhancing the CNR and signal-to-noise ratio while reducing beam-hardening artifacts. DECT can improve detection and characterization of hepatic abnormalities, including mass lesions. The technique can also be used for the diagnosis of steatosis and iron overload. This article reviews and illustrates the different applications of DECT in liver imaging.

A comprehensive assessment of physical image quality of five different scanners for head CT imaging as clinically used at a single hospital centre-A phantom study

Nowadays, given the technological advance in CT imaging and increasing heterogeneity in characteristics of CT scanners, a number of CT scanners with different manufacturers/technologies are often installed in a hospital centre and used by various departments. In this phantom study, a comprehensive assessment of image quality of 5 scanners (from 3 manufacturers and with different models) for head CT imaging, as clinically used at a single hospital centre, was hence carried out. Helical and/or sequential acquisitions of the Catphan-504 phantom were performed, using the scanning protocols (CTDI_vol range: 54.7–57.5 mGy) employed by the staff of various Radiology/Neuroradiology departments of our institution for routine head examinations. CT image quality for each scanner/acquisition protocol was assessed through noise level, noise power spectrum (NPS), contrast-to-noise ratio (CNR), modulation transfer function (MTF), low contrast detectability (LCD) and non-uniformity index analyses. Noise values ranged from 3.5 HU to 5.7 HU across scanners/acquisition protocols. NPS curves differed in terms of peak position (range: 0.21–0.30 mm^-1). A substantial variation of CNR values with scanner/acquisition protocol was observed for different contrast inserts. The coefficient of variation (standard deviation divided by mean value) of CNR values across scanners/acquisition protocols was 18.3%, 31.4%, 34.2%, 30.4% and 30% for teflon, delrin, LDPE, polystyrene and acrylic insert, respectively. An appreciable difference in MTF curves across scanners/acquisition protocols was revealed, with a coefficient of variation of f_50%/f_10% of MTF curves across scanners/acquisition protocols of 10.1%/7.4%. A relevant difference in LCD performance of different scanners/acquisition protocols was found. The range of contrast threshold for a typical object size of 3 mm was 3.7–5.8 HU. Moreover, appreciable differences in terms of NUI values (range: 4.1%-8.3%) were found. The analysis of several quality indices showed a non-negligible variability in head CT imaging capabilities across different scanners/acquisition protocols. This highlights the importance of a physical in-depth characterization of image quality for each CT scanner as clinically used, in order to optimize CT imaging procedures.

Building a dual-energy CT service line in abdominal radiology

As the access of radiology practices to dual-energy CT (DECT) has increased worldwide, seamless integration into clinical workflows and optimized use of this technology are desirable. In this article, we provide basic concepts of commercially available DECT hardware implementations, discuss financial and logistical aspects, provide tips for protocol building and image routing strategies, and review radiation dose considerations to establish a DECT service line in abdominal imaging. KEY POINTS: • Tube-based and detector-based DECT implementations with varying features and strengths are available on the imaging market. • Thorough assessment of financial and logistical aspects is key to successful implementation of a DECT service line. • Optimized protocol building and image routing strategies are of critical importance for effective use and seamless inception of DECT in routine clinical workflows.

Higher patient doses through X-ray imaging procedures

Medical imaging using X-rays has been one of the most popular imaging modalities ever since the discovery of X-rays 125 years ago. With unquestionable benefits, concerns about radiation risks have frequently been raised. Computed tomography (CT) and fluoroscopic guided interventional procedures have the potential to impart higher radiation exposure to patients than radiographic examinations. Despite technological advances, there have been instances of increased doses per procedure mainly because of better diagnostic information in images. However, cumulative dose from multiple procedures is creating new concerns as effective doses >100 mSv are not uncommon. There is a need for action at all levels. Manufacturers must produce equipment that can provide a quality diagnostic image at substantially lesser dose and better implementation of optimization strategies by users. There is an urgent need for the industry to develop CT scanners with sub-mSv radiation dose, a goal that has been lingering. It appears that a new monochromatic X-ray source will lead to replacement of X-ray tubes all over the world in coming years and will lead to a drastic reduction in radiation doses. This innovation will impact all X-ray imaging and will help dose reduction. For interventional procedures, the likely employment of robotic systems in practice may drastically reduce radiation exposures to operators- but patient exposure will still remain an issue. Training needs always need to be emphasized and practiced.

Dual source hybrid spectral micro-CT using an energy-integrating and a photon-counting detector

Preclinical micro-CT provides a hotbed in which to develop new imaging technologies, including spectral CT using photon counting detector (PCD) technology. Spectral imaging using PCDs promises to expand x-ray CT as a functional imaging modality, capable of molecular imaging, while maintaining CT's role as a powerful anatomical imaging modality. However, the utility of PCDs suffers due to distorted spectral measurements, affecting the accuracy of material decomposition. We attempt to improve material decomposition accuracy using our novel hybrid dual-source micro-CT system which combines a PCD and an energy integrating detector. Comparisons are made between PCD-only and hybrid CT results, both reconstructed with our iterative, multi-channel algorithm based on the split Bregman method and regularized with rank-sparse kernel regression. Multi-material decomposition is performed post-reconstruction for separation of iodine (I), gold (Au), gadolinium (Gd), and calcium (Ca). System performance is evaluated first in simulations, then in micro-CT phantoms, and finally in an in vivo experiment with a genetically modified p53fl/fl mouse cancer model with Au, Gd, and I nanoparticle (NP)-based contrasts agents. Our results show that the PCD-only and hybrid CT reconstructions offered very similar spatial resolution at 10% MTF (PCD: 3.50 lp mm-1; hybrid: 3.47 lp mm-1) and noise characteristics given by the noise power spectrum. For material decomposition we note successful separation of the four basis materials. We found that hybrid reconstruction reduces RMSE by an average of 37% across all material maps when compared to PCD-only of similar dose but does not provide much difference in terms of concentration accuracy. The in vivo results show separation of targeted Au and accumulated Gd NPs in the tumor from intravascular iodine NPs and bone. Hybrid spectral micro-CT can benefit nanotechnology and cancer research by providing quantitative imaging to test and optimize various NPs for diagnostic and therapeutic applications.

Comparison of Dual- and Single-Source Dual-Energy CT for Diagnosis of Acute Pulmonary Artery Embolism

PURPOSE

 Comparison of dual-source dual-energy CT (DS-DECT) and split-filter dual-energy CT (SF-DECT) regarding image quality and radiation dose in patients with suspected pulmonary embolism.

MATERIALS AND METHODS

 We retrospectively analyzed pulmonary dual-energy CT angiography (CTPA) scans performed on two different CT scanners in 135 patients with suspected pulmonary embolism (PE). Scan parameters for DS-DECT were 90/Sn150 kV (n = 68 patients), and Au/Sn120 kV for SF-DECT (n = 67 patients). The iodine delivery rate was 1400 mg/s in the DS-DECT group vs. 1750 mg/s in the SF-DECT group. Color-coded iodine distribution maps were generated for both protocols. Objective (CT attenuation of pulmonary trunk [HU], signal-to-noise ratio [SNR], contrast-to-noise ratio [CNR]) and subjective image quality parameters (two readers [R], five-point Likert scale), as well as radiation dose parameters (effective radiation dose, size-specific dose estimations [SSDE]) were compared.

RESULTS

 All CTPA scans in both groups were of diagnostic image quality. Subjective CTPA image quality was rated as good or excellent in 80.9 %/82.4 % (R1 / R2) of DS-DECT scans, and in 77.6 %/76.1 % of SF-DECT scans. For both readers, the image quality of split-filter iodine distribution maps was significantly lower (p < 0.05) with good or excellent ratings in only 43.3 %/46.3 % (R1 / R2) vs. 83.8 %/88.2 % for maps from DS-DECT. The HU values of the pulmonary trunk did not differ between the two techniques (p = n. s.), while both the SNR and CNR were significantly higher in the split-filter group (p < 0.001; p = 0.003). Both effective radiation dose (2.70 ± 1.32 mSv vs. 2.89 ± 0.94 mSv) and SSDE (4.71 ± 1.63 mGy vs. 5.84 ± 1.11 mGy) were significantly higher in the split-filter group (p < 0.05).

CONCLUSION

 The split-filter allows for dual-energy imaging of suspected pulmonary embolism but is associated with lower iodine distribution map quality and higher radiation dose.

KEY POINTS

  · The split-filter allows for dual-energy data acquisition from single-source single-layer CT scanners.. · Compared to the assessed dual-source dual-energy system, split-filter dual-energy imaging of a suspected pulmonary embolism is associated with lower iodine distribution map quality and higher radiation dose.. · Both the split-filter and the dual-source scanner provide diagnostic image quality in CTPA..

CITATION FORMAT

· Petritsch B, Pannenbecker P, Weng AM et al. Comparison of Dual- and Single-Source Dual-Energy CT for Diagnosis of Acute Pulmonary Artery Embolism. Fortschr Röntgenstr 2021; 193: 427 - 436.

Principal Component Analysis in Projection and Image Domains-Another Form of Spectral Imaging in Photon-Counting CT

OBJECTIVE

We explore the feasibility of principal component analysis (PCA) as a form of spectral imaging in photon-counting CT.

METHODS

Using the data acquired by a prototype system and simulated by computer, we investigate the feasibility of spectral imaging in photon-counting CT via PCA for feature extraction and study the impacts made by data standardization and de-noising on its performance.

RESULTS

The PCA in the projection domain maintains the data consistence that is essential for tomographic image reconstruction and performs virtually the same as that in the image domain. The first three primary components account for more than 99.99% covariance of the data. Within anticipation, the contrast-to-noise ratio (CNR) between the target and background in the first principal component image can be larger than that in the image generated from the data acquired in each energy bin. More importantly, the CNR in the first principal component image may be larger than that in the image formed by the summed data acquired in all energy bins (i.e., the conventional polychromatic CT image). In addition, de-noising can not only reduce the noise in images but also improve the effectiveness/efficiency of PCA in feature extraction.

CONCLUSION

The PCA in either projection or image domain provides another form of spectral imaging in photon-counting CT that fits the essential requirements on spectral imaging in true color.

SIGNIFICANCE

The verification of PCA's feasibility in CT as a form spectral imaging and observation of its potential superiority in CNR over conventional polychromatic CT are meaningful in theory and practice.

Grating-based Spectral CT using Small Angle X-ray Beam Deflections

Interest in spectral CT for diagnostics and therapy evaluation has been growing. Acquisitions of data from distinct energy spectra provide, among other advantages, quantitative density estimations for multiple materials. We introduce a novel spectral CT concept that includes a fine-pitch grating for prefiltration of the x-ray beam. The attenuation behavior of this grating changes significantly if x-rays are slightly angled in relation to the grating structures. To apply such an angle (i.e. switch between the different filtrations) we propose a fast, controllable, and precise solution by moving the focal spot of the x-ray tube. In this work, we performed preliminary evaluations with a grating prototype on a CT test bench. Our results include x-ray spectrometer measurements that reveal diverse and controllable spectral shaping between 4° and 6° for a specific grating design. Additional experiments with a contrast agent phantom illustrated the capability to decompose clinically relevant iodine concentrations (5, 10, 20, and 50mg/mL) - demonstrating the feasibility of the grating-based approach. Ongoing and future studies will investigate the potential of this novel concept as a relatively simple upgrade to standard energy-integrating CT.

Image Quality and Dose Comparison of Single-Energy CT (SECT) and Dual-Energy CT (DECT)

CT and its comprehensive usage have become one of the most indispensable components in medical field especially in the diagnosis of several diseases. SECT and DECT have developed CT diagnostic potentials in several means. In this review article we have discussed the basic principles of single-energy and dual-energy computed tomography and their important physical differences which can cause better diagnostic evaluation. Moreover, different organs diagnostic evaluations through single-energy and dual-energy computed tomography have been discussed. Conventional or single-energy CT (SECT) uses a single polychromatic X-ray beam (ranging from 70 to 140 kVp with a standard of 120 kVp) emitted from a single source and received by a single detector. The concept of dual-energy computed tomography (DECT) is almost as old as the CT technology itself; DECT initially required substantially higher radiation doses (nearly two times higher than those employed in single-energy CT) and presented problems associated with spatial misregistration of the two different kV image datasets between the two separate acquisitions. The basic principles of single-energy and dual-energy computed tomography and their important physical differences can cause better diagnostic evaluation. Moreover, different organs diagnostic evaluations through single-energy and dual-energy computed tomography have been discussed. According to diverse data and statistics it is controversial to definitely indicate the accurate comparison of image quality and dose amount.

Acquisition time, radiation dose, subjective and objective image quality of dual-source CT scanners in acute pulmonary embolism: a comparative study

OBJECTIVES

To compare the scan acquisition time, radiation dose, subjective and objective image quality of two dual-source CT scanners (DSCT) for detection of acute pulmonary embolism.

METHODS

Two hundred twenty-one scans performed on the 2nd-generation DSCT and 354 scans on the 3rd-generation DSCT were included in this large retrospective study. In a randomized blinded design, two radiologists independently reviewed the scans using a 5-point Likert scale. Radiation dose and objective image quality parameters were calculated.

RESULTS

Mean acquisition time was significantly lower in the 3rd-generation DSCT (2.81 s ± 0.1 in comparison with 9.7 s ± 0.15 [mean ± SD] respectively; p < 0.0001) with the 3rd generation 3.4 times faster. The mean subjective image quality score was 4.33/5 and 4/5 for the 3rd- and 2nd-generation DSCT respectively (p < 0.0001) with strong interobserver reliability agreement. DLP, CTDI_vol, and ED were significantly lower in the 3rd than the 2nd generation (175.6 ± 63.7 mGy cm; 5.3 ± 1.9 mGy and 2.8 ± 1.2 mSv in comparison with 266 ± 255 mGy.cm; 7.8 ± 2.2 mGy and 3.8 ± 4.3 mSv). Noise was significantly lower in the 3rd generation (p < 0.01). Signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR), and figure of merit (FOM), a dose-insensitive index for CNR, were significantly higher in the 3rd-generation DSCT (33.5 ± 23.4; 29.0 ± 21.3 and 543.7 ± 1037 in comparison with 23.4 ± 17.7; 19.4 ± 16.0 and 170.5 ± 284.3).

CONCLUSION

Objective and subjective image quality are significantly higher on the 3rd-generation DSCT with significantly lower mean acquisition time and radiation dose.

KEY POINTS

• The 3rd-generation DSCT scanner provides an improved image quality, less perceived artifacts, and lower radiation dose in comparison with the 2nd-generation DSCT, when operating in dual-energy (DE) mode. • The 3.4-times-faster 3rd-generation DSCT scanner can be of particular value in patients with chronic lung diseases or breathing difficulties that prevent adequate breathhold.

Transorbital nonmissile penetrating brain injury: Report of two cases

BACKGROUND

Penetrating brain injury (PBI) is an uncommon emergency in neurosurgery, and transorbital PBI is a rare type of PBI. Reasonable surgical planning and careful postoperative management can improve the prognosis of patients

CASE SUMMARY

The first case is a 68-year-old male patient who was admitted to the hospital because a branch punctured his brain through the orbit for approximately 9 h after he unexpectedly fell while walking. After admission, the patient underwent emergency surgical treatment and postoperative anti-infection treatment. The patient was able to follow instructions at a 4-mo follow-up review. The other case is a 46-year-old male patient who was admitted to the hospital due to an intraorbital foreign body caused by a car accident, after which the patient was unconscious for approximately 6 h. After admission, the patient underwent emergency surgical treatment and postoperative anti-infection treatment. The patient could correctly answer questions at a 3-mo follow-up review.

CONCLUSION

Transorbital PBI is a rare and acute disease. Early diagnosis, surgical intervention, and application of intravenous antibiotics can improve the prognosis and quality of life of patients.

Relationship between urate within tophus and bone erosion according to the anatomic location of urate deposition in gout: A quantitative analysis using dual-energy CT volume measurements

The aim of this study was to measure the urate volume within tophus and bone erosion volume using dual-energy computed tomography in patients with tophaceous gout. Furthermore, our study aims to quantitatively analyze the relationship between monosodium urate (MSU) crystal deposition and bone erosion according to the anatomic location of urate deposition.Seventy-seven subjects with chronic gout were positively identified for the presence of urate deposition. Only 27 subjects identified for the presence of urate in contact with bone erosion were included in this study. The urate volumes and associated erosion volumes were measured. The relationships between urate within tophus and bone erosion were separately analyzed according to the anatomic location of urate deposition.Twenty-seven subjects were all male (100%) with a median (interquartile range, IQR) age of 52 (45-61) years. From all the subjects, 103 tophi depositions were identified in contact with bone erosion, including 58/103 tophi that contained an intraosseous component and 45/103 nonintraosseous tophi. Tophi containing intraosseous components were larger than nonintraosseous tophi (urate volume: median [IQR] 45.64 [4.79-250.89] mm vs 19.32 [6.97-46.71] mm, P = .035) and caused greater bone erosion (erosion volume: 249.03 [147.08-845.33] mm vs 69.07 [32.88-111.24] mm, P < .001). Almost all erosion volumes were larger than urate volumes in nonperiarticular tophi, in contrast to most erosion volumes, which were less than urate volumes in the tophi that contained a periarticular component (odds ratio, 95% confidence interval: 74.00, 14.70-372.60; P < .001). Urate volume and erosion volume demonstrated positive correlations in intraosseous tophi, intraosseous-intra-articular-periarticular tophi, and intraosseous-intra-articular tophi (rs = 0.761, rs = 0.695, rs = 0.629, respectively, P < .05).MSU crystal deposition shows a promoting effect on the development of bone erosions in varying degrees, associated with the location of MSU crystals deposited in the joints. The intraosseous tophi contribute the most to bone erosions, followed by intra-articular tophi, and periarticular tophi.

Dual-energy CT for routine imaging of the abdomen and pelvis: radiation dose and image quality

PURPOSE

To assess the radiation dose and image quality of routine dual energy CT (DECT) of the abdomen and pelvis performed in the emergency department setting, compared with single energy CT (SECT).

MATERIALS AND METHODS

Seventy-five consecutive routine contrast-enhanced SECT scans of the abdomen and pelvis meeting inclusion criteria were compared with 75 routine contrast-enhanced DECT scans matched by size and patient weight (within 10 lbs), performed on the same dual-source DECT scanner. Cohorts were compared in terms of radiation dose metrics of CT dose index (CTDI_vol) and dose length product (DLP), objective measurements of image quality (signal, noise, and signal-to-noise ratio of a variety of anatomical landmarks), and subjective measurements of image quality scored by two emergency radiologists.

RESULTS

Demographics and patient size were not statistically different between DECT and SECT cohorts. Both average scans CTDI_vol and DLP were significantly lower with DECT than with SECT. Average scan CTDI_vol for SECT was 14.7 mGy (± 6.6) and for DECT was 10.9 mGy (± 3.8) (p < 0.0001). Average scan DLP for SECT was 681.5 mGy cm (± 339.3) and for DECT was 534.8 mGy cm (± 201.9) (p < 0.0001). For objective image quality metrics, for all structures measured, noise was significantly lower and SNR was significantly higher with DECT compared with SECT. For subjective image quality, for both readers, there was no significant difference between SECT and DECT in subjective image quality for soft tissues and vascular structures, or for subjective image noise.

CONCLUSIONS

DECT was performed with decreased radiation dose when compared with SECT, demonstrated improved objective measurements of image quality, and equivalent subjective image quality.

Understanding, justifying, and optimizing radiation exposure for CT imaging in nephrourology

An estimated 4-5 million CT scans are performed in the USA every year to investigate nephrourological diseases such as urinary stones and renal masses. Despite the clinical benefits of CT imaging, concerns remain regarding the potential risks associated with exposure to ionizing radiation. To assess the potential risk of harmful biological effects from exposure to ionizing radiation, understanding the mechanisms by which radiation damage and repair occur is essential. Although radiation level and cancer risk follow a linear association at high doses, no strong relationship is apparent below 100 mSv, the doses used in diagnostic imaging. Furthermore, the small theoretical increase in risk of cancer incidence must be considered in the context of the clinical benefit derived from a medically indicated CT and the likelihood of cancer occurrence in the general population. Elimination of unnecessary imaging is the most important method to reduce imaging-related radiation; however, technical aspects of medically justified imaging should also be optimized, such that the required diagnostic information is retained while minimizing the dose of radiation. Despite intensive study, evidence to prove an increased cancer risk associated with radiation doses below ~100 mSv is lacking; however, concerns about ionizing radiation in medical imaging remain and can affect patient care. Overall, the principles of justification and optimization must remain the basis of clinical decision-making regarding the use of ionizing radiation in medicine.

Dual-Energy CT in Children: Imaging Algorithms and Clinical Applications

Dual-energy CT enables the simultaneous acquisition of CT images at two different x-ray energy spectra. By acquiring high- and low-energy spectral data, dual-energy CT can provide unique qualitative and quantitative information about tissue composition, allowing differentiation of multiple materials including iodinated contrast agents. The two dual-energy CT postprocessing techniques that best exploit the advantages of dual-energy CT in children are the material-decomposition images (which include virtual nonenhanced, iodine, perfused lung blood volume, lung vessel, automated bone removal, and renal stone characterization images) and virtual monoenergetic images. Clinical applications include assessment of the arterial system, lung perfusion, neoplasm, bowel diseases, renal calculi, tumor response to treatment, and metal implants. Of importance, the radiation exposure level of dual-energy CT is equivalent to or less than that of conventional single-energy CT. In this review, the authors discuss the basic principles of the dual-energy CT technologies and postprocessing techniques and review current clinical applications in the pediatric chest and abdomen.

Combining non-contrast and dual-energy CT improves diagnosis of early gout

OBJECTIVES

To determine the incremental value of non-contrast CT (NCCT) on dual-energy CT (DECT) in symptomatic first metatarsophalangeal (MTP) joints in early gout.

METHODS

One hundred and fifteen painful joints were consecutively enrolled and gout was diagnosed based on the 2015 EULAR/ACR criteria and/or arthrocentesis. Two readers independently evaluated DECT alone and combined NCCT and DECT (NCCT+DECT) based on four semiquantitative scales. Sensitivities and specificities were compared using McNemar's test. AUC was compared.

RESULTS

Of the 115 joints, 72 were defined as an early gout group and 43 as a gout-negative group after exclusion. The sensitivity and specificity for the early gout group on DECT alone were as followed: reader 1 - 52.8% and 100.0% and reader 2 - 51.4% and 100.0%. NCCT+DECT results were as follows: reader 1 - 79.2% and 93.0% and reader 2 - 79.2% and 95.3%. AUC was significantly higher in NCCT+DECT compared to that in DECT alone for the early gout group (0.888 vs. 0.774 for reader 1, p = 0.0004; 0.896 vs. 0.816 for reader 2, p = 0.0142). The false-negative cases on DECT occurred more frequently with the first-onset gout, and tended to be affected by a longer duration of symptoms in the post-hoc analysis.

CONCLUSION

The combined analysis of NCCT and DECT improves diagnostic capabilities in symptomatic early gout involving the first MTP joint.

KEY POINTS

• MSU crystal depositions in early gout may be seen on non-contrast CT, while still being undetectable by DECT. • Combining non-contrast CT and DECT improves detection of early gout. • False negatives of DECT are more common than previously reported in cases of first-onset gout.

Current and Novel Techniques for Metal Artifact Reduction at CT: Practical Guide for Radiologists

Artifacts caused by metallic implants appear as dark and bright streaks at computed tomography (CT), which severely degrade the image quality and decrease the diagnostic value of the examination. When x-rays pass through a metal object, depending on its size and composition, different physical effects negatively affect the measurements in the detector, most notably the effects of photon starvation and beam hardening. To improve image quality and recover information about underlying structures, several artifact reduction methods have been introduced in modern CT systems. Projection-based metal artifact reduction (MAR) algorithms act in projection space and replace corrupted projections caused by metal with interpolation from neighboring uncorrupted projections. MAR algorithms primarily suppress artifacts that are due to photon starvation. The dual-energy CT technique is characterized by data acquisition at two different energy spectra. Dual-energy CT provides synthesized virtual monochromatic images at different photon energy (kiloelectron volt) levels, and virtual monochromatic images obtained at high kiloelectron volt levels are known to reduce the effects of beam hardening. In clinical practice, although MAR algorithms can be applied after image acquisition, the decision whether to apply dual-energy CT for the patient usually needs to be made before image acquisition. Radiologists should be more familiar with the clinical and technical features of each method and should be able to choose the optimal method according to the clinical situation. ^©RSNA, 2018.

Single-energy metal artifact reduction technique for reducing metallic coil artifacts on post-interventional cerebral CT and CT angiography

PURPOSE

To evaluate the effects of the single-energy metal artifact reduction (SEMAR) algorithm on image quality of cerebral CT and CT angiography (CTA) for patients who underwent intracranial aneurysm coiling.

METHODS

Twenty patients underwent cerebral CT and CTA using a 320-detector row CT after intracranial aneurysm coiling. Images with and without application of the SEMAR algorithm (SEMAR CT and standard CT images, respectively) were reconstructed for each patient. The images were qualitatively assessed by two independent radiologists in a blinded manner for the depiction of anatomical structures around the coil, delineation of the arteries around the coil, and the depiction of the status of coiled aneurysms. Artifact strength was quantitatively assessed by measuring the standard deviation of attenuation values around the coil.

RESULTS

The strength of artifacts measured in SEMAR CT images was significantly lower than that in standard CT images (25.7 ± 10.2 H.U. vs. 80.4 ± 67.2 H.U., p < 0.01, Student's paired t test). SEMAR CT images were significantly improved compared with standard CT images in the depiction of anatomical structures around the coil (p < 0.01, the sign test), delineation of the arteries around the coil (p < 0.01), and the depiction of the status of coiled aneurysms (p < 0.01).

CONCLUSION

The SEMAR algorithm significantly reduces metal artifacts from intracranial aneurysm coiling and improves visualization of anatomical structures and arteries around the coil, and depiction of the status of coiled aneurysms on post-interventional cerebral CT.

Metal artifact reduction by filter-based dual-energy cone-beam computed tomography on a bench-top micro-CBCT system: concept and demonstration

We evaluated two dual-energy cone-beam computed tomography (DE-CBCT) methodologies for a bench-top micro-CBCT system to reduce metal artifacts on reconstructed images. Two filter-based DE-CBCT methodologies were tested: (i) alternative spectral switching and (ii) simultaneous beam splitting. We employed filters of 0.6-mm-thick tin and 0.1-mm-thick tungsten to generate high- and low-energy spectra from 120 kVp X-rays, respectively. The spectral switching method was imitated by two half scans with different filters (pseudo-switching). Filters were placed and between the X-ray tube and a phantom ('1-u,' '2-u'), a phantom and a flat panel detector ('1-d,' '2-d'), and compared with (iii) two half scans at 80 and 140 kVp [pseudo-(80,140)]. For the splitting method, two half-width filters were aligned along a rotating axis. Projections were separated into halves and merged with corresponding areas of opposed projections after one full rotation. A solid 30-mm-diameter acrylic phantom and an acrylic phantom with four 5-mm-diameter titanium rods were used. DE images were generated by weighted summation of the high- and low-energy images. The blending factor was changed from 0 to +5 in increments of 0.01. Relative errors (REs) of the linear attenuation coefficients of the two phantoms and the contrast-to-noise ratios (CNRs) between the titanium and acrylic regions were compared. All methods showed zero REs except for the method (2-d). CNRs for pseudo-switching with upstream placement were 1.4-fold larger than CNRs for the pseudo-(80,140) method. CNRs for the downstream placements were small. It was concluded that the pseudo-switching method with upstream placement is appropriate for reducing metal artifacts.

Use of Dual-Energy Computed Tomography for Evaluation of Genitourinary Diseases

Since its clinical inception a decade ago, dual-energy computed tomography has expanded the array of computed tomography imaging tools available to the practicing abdominal radiologist. Of note, diagnostic solutions for imaging-based evaluation of genitourinary diseases, foremost kidney calculi and renal tumors characterization, represent the apogee applications of dual-energy computed tomography in abdominal imaging. This article reviews clinical applications of dual-energy computed tomography for the assessment of genitourinary diseases.

Comparison of single and dual energy CT for stopping power determination in proton therapy of head and neck cancer

Background and purpose

Patients with head and neck (HN) cancer may benefit from proton therapy due to the potential for sparing of normal tissue. For planning of proton therapy, dual-energy CT (DECT) has been shown to provide superior stopping power ratio (SPR) determination in phantom materials and organic tissue samples, compared to single-energy CT (SECT). However, the benefit of DECT in HN cancer patients has not yet been investigated. This study therefore compared DECT- and SECT-based SPR estimation for HN cancer patients.

Materials and methods

Fourteen HN cancer patients were DECT scanned. Eight patients were scanned using a dual source DECT scanner and six were scanned with a conventional SECT scanner by acquiring two consecutive scans. SECT image sets were computed as a weighted summation of the low and high energy DECT image sets. DECT- and SECT-based SPR maps were derived. Water-equivalent path lengths (WEPLs) through the SPR maps were compared in the eight cases with dual source DECT scans. Mean SPR estimates over region-of-interests (ROIs) in the cranium, brain and eyes were analyzed for all patients.

Results

A median WEPL difference of 1.9 mm (1.5%) was found across the eight patients. Statistically significant SPR differences were seen for the ROIs in the brain and eyes, with the SPR estimates based on DECT overall lower than for SECT.

Conclusions

Clinically relevant WEPL and SPR differences were found between DECT and SECT, which could imply that the accuracy of treatment planning for proton therapy would benefit from DECT-based SPR estimation.

Perforating head injury with iron rod and its miraculous escape: Case report and review of literature

Civilian perforating head injury is rare. Because rarity of this injury, there is no standard management protocol. We report a case of perforating head injury with iron rod, review the literature on the subject and discuss the challenges in the management of such case. We have not found similar case in the literature. Civilian perforating head injury is rare. A 25-year-male brought to the emergency department with approximately two feet perforating iron rod in the head, entering via frontal region, left side of midline and coming out of the occipital region. He developed right sided hemiplegia and global aphasia. He underwent series of imaging for the evaluation of the course of the iron rod and injury sustained because of it. Under strict aseptic precaution, iron rod removed in the operation theater. His clinical condition improved over a period of three weeks. At one year follow up- he had almost normal speech and language functions and was able to walk without support. This case illustrates the possibility of bizarre type of such injury in the presence of protective helmet and challenges in the management. Preoperative planning on the basis of images, prophylactic antibiotics and anticonvulsant medications, cleaning of the objects with antiseptic solutions, anterograde extraction after adequate exposure around entry and exit points resulted in good clinical outcome after successful removal of the rod.