High-pressure studies of size dependent yield strength in rhenium diboride nanocrystals

The superhard ReB2 system is the hardest pure phase diboride synthesized to date. Previously, we have demonstrated the synthesis of nano-ReB2 and the use of this nanostructured material for texture analysis using high-pressure radial diffraction. Here, we investigate the size dependence of hardness in the nano-ReB2 system using nanocrystalline ReB2 with a range of grain sizes (20-60 nm). Using high-pressure X-ray diffraction, we characterize the mechanical properties of these materials, including bulk modulus, lattice strain, yield strength, and texture. In agreement with the Hall-Petch effect, the yield strength increases with decreasing size, with the 20 nm ReB2 exhibiting a significantly higher yield strength than any of the larger grained materials or bulk ReB2. Texture analysis on the high pressure diffraction data shows a maximum along the [0001] direction, which indicates that plastic deformation is primarily controlled by the basal slip system. At the highest pressure (55 GPa), the 20 nm ReB2 shows suppression of other slip systems observed in larger ReB2 samples, in agreement with its high yield strength. This behavior, likely arises from an increased grain boundary concentration in the smaller nanoparticles. Overall, these results highlight that even superhard materials can be made more mechanically robust using nanoscale grain size effects.

Tensorial stress-plastic strain fields in α - ω Zr mixture, transformation kinetics, and friction in diamond-anvil cell

Various phenomena (phase transformations (PTs), chemical reactions, microstructure evolution, strength, and friction) under high pressures in diamond-anvil cell are strongly affected by fields of stress and plastic strain tensors. However, they could not be measured. Here, we suggest coupled experimental-analytical-computational approaches utilizing synchrotron X-ray diffraction, to solve an inverse problem and find fields of all components of stress and plastic strain tensors and friction rules before, during, and after α-ω PT in strongly plastically predeformed Zr. Results are in good correspondence with each other and experiments. Due to advanced characterization, the minimum pressure for the strain-induced α-ω PT is changed from 1.36 to 2.7 GPa. It is independent of the plastic strain before PT and compression-shear path. The theoretically predicted plastic strain-controlled kinetic equation is verified and quantified. Obtained results open opportunities for developing quantitative high-pressure/stress science, including mechanochemistry, synthesis of new nanostructured materials, geophysics, astrogeology, and tribology.

Imaging of the electronic bonding of diamond at pressures up to 2 million atmospheres

Diamond shows unprecedented hardness. Because hardness is a measure of resistance of chemical bonds in a material to external indentation, the electronic bonding nature of diamond beyond several million atmospheres is key to understanding the origin of hardness. However, probing the electronic structures of diamond at such extreme pressure has not been experimentally possible. The measurements on the inelastic x-ray scattering spectra for diamond up to 2 million atmospheres provide data on the evolution of its electronic structures under compression. The mapping of the observed electronic density of states allows us to obtain a two-dimensional image of the bonding transitions of diamond undergoing deformation. The spectral change near edge onset is minor beyond a million atmospheres, while its electronic structure displays marked pressure-induced electron delocalization. Such electronic responses indicate that diamond's external rigidity is supported by its ability to reconcile internal stress, providing insights into the origins of hardness in materials.

Stress-induced high-Tc superconductivity in solid molecular hydrogen

Solid molecular hydrogen has been predicted to be metallic and high-temperature superconducting at ultrahigh hydrostatic pressures that push current experimental limits. Meanwhile, little is known about the influence of nonhydrostatic conditions on its electronic properties at extreme pressures where anisotropic stresses are inevitably present and may also be intentionally introduced. Here we show by first-principles calculations that solid molecular hydrogen compressed to multimegabar pressures can sustain large anisotropic compressive or shear stresses that, in turn, cause major crystal symmetry reduction and charge redistribution that accelerate bandgap closure and promote superconductivity relative to pure hydrostatic compression. Our findings highlight a hitherto largely unexplored mechanism for creating superconducting dense hydrogen, with implications for exploring similar phenomena in hydrogen-rich compounds and other molecular crystals.

Electronic, Structural, and Mechanical Properties of SiO_{2} Glass at High Pressure Inferred from its Refractive Index

We report the first direct measurements of the refractive index of silica glass up to 145 GPa that allowed quantifying its density, bulk modulus, Lorenz-Lorentz polarizability, and band gap. These properties show two major anomalies at ∼10 and ∼40  GPa. The anomaly at ∼10  GPa signals the onset of the increase in Si coordination, and the anomaly at ∼40  GPa corresponds to a nearly complete vanishing of fourfold Si. More generally, we show that the compressibility and density of noncrystalline solids can be accurately measured in simple optical experiments up to at least 110 GPa.

Dynamic Strength of Iron at High Pressures and Strain Rates

Accurate modeling of meteorite impacts, and deformation of planetary cores require characterization of the flow strength and in-elasticity of iron in its different phases. In this Letter, we investigate the flow strength of both the ambient α phase and high-pressure ε phase of iron at strain rates of 1×10^{5}  s^{-1} and pressures up to 42 GPa using high-pressure-pressure shear plate impact experiments. We report the strength of the ε iron to be significantly higher than α phase but consequently one order smaller than the previously reported dynamic strength at high pressures. The complete stress-strain response of the ε phase is reported for the first time.

Femtosecond Visualization of hcp-Iron Strength and Plasticity under Shock Compression

Iron is a key constituent of planets and an important technological material. Here, we combine in situ ultrafast x-ray diffraction with laser-induced shock compression experiments on Fe up to 187(10) GPa and 4070(285) K at 10^{8}  s^{-1} in strain rate to study the plasticity of hexagonal-close-packed (hcp)-Fe under extreme loading states. {101[over ¯]2} deformation twinning controls the polycrystalline Fe microstructures and occurs within 1 ns, highlighting the fundamental role of twinning in hcp polycrystals deformation at high strain rates. The measured deviatoric stress initially increases to a significant elastic overshoot before the onset of flow, attributed to a slower defect nucleation and mobility. The initial yield strength of materials deformed at high strain rates is thus several times larger than their longer-term flow strength. These observations illustrate how time-resolved ultrafast studies can reveal distinctive plastic behavior in materials under extreme environments.

A Review of the Melting Curves of Transition Metals at High Pressures Using Static Compression Techniques

The accurate determination of melting curves for transition metals is an intense topic within high pressure research, both because of the technical challenges included as well as the controversial data obtained from various experiments. This review presents the main static techniques that are used for melting studies, with a strong focus on the diamond anvil cell; it also explores the state of the art of melting detection methods and analyzes the major reasons for discrepancies in the determination of the melting curves of transition metals. The physics of the melting transition is also discussed.

A Practical Review of the Laser-Heated Diamond Anvil Cell for University Laboratories and Synchrotron Applications

In the past couple of decades, the laser-heated diamond anvil cell (combined with in situ techniques) has become an extensively used tool for studying pressure-temperature-induced evolution of various physical (and chemical) properties of materials. In this review, the general challenges associated with the use of the laser-heated diamond anvil cells are discussed together with the recent progress in the use of this tool combined with synchrotron X-ray diffraction and absorption spectroscopy.

Theoretical development and experimental validation on the measurement of temperature by extended X-ray absorption fine structure

A systematic investigation on the theoretical framework of the ultra-fast measurement of temperature by extended X-ray absorption fine structure (EXAFS) applied in laser-driven-compression experiments has been carried out and a new temperature measurement scheme based on the EXAFS cumulant expansion analysis and anharmonic correlated Debye model has been advanced. By considering the anharmonic effect of thermal vibration and avoiding the employment of the empirical model as well as parameters which have large inherent uncertainties in the temperature determination, this new scheme is theoretically more accurate than traditional ones. Then the performance of the new measurement scheme and traditional methods were validated on a synchrotron radiation platform by temperature-dependent EXAFS (TDEXAFS) experiments on Au, Fe, V and Ti; the results showed that the new scheme could provide the most accurate measured temperatures with much lower uncertainties. This accurate scheme gives a firmer physical ground to the EXAFS temperature measurement technique and can expect to be applied in laser-driven compression experiments and promote the development of matter state research at extreme conditions.

Mechanical Strength Evaluation of Elastic Materials by Multiphysical Nondestructive Methods: A Review

The main purpose of industrial nondestructive testing (NDT) is to diagnose the stability, reliability and failure probability of materials, components and structures. Industrial component mechanical strength is one of the most important properties NDT is used to characterize. Subtle but perceptible changes in stress-strain behavior can be reliable indicators of defect formation. A detailed review on the state-of-the-art NDT methods using optical-radiation, photoacoustic, and photothermal techniques for mechanical strength evaluation and defect pre-diagnosis is presented in this article. Mechanical strength is analyzed in terms of the deformation/strain field, the stress-strain relation, and the residual stress in an elastic material subjected to tensile or compressive loading, or impact. By introducing typical NDT experiments, the history and features of each methodology are revisited and typical applications are discussed. This review also aims to be used as a reference toward further research and development of NDT technologies characterizing mechanical strength of materials and components.

Heat-release equation of state and thermal conductivity of warm dense carbon by proton differential heating

Warm dense carbon is generated at 0.3-2.0 g/cc and 1-7 eV by proton heating. The release equation of state (EOS) after heating and thermal conductivity of warm dense carbon are studied experimentally in this regime using a Au/C dual-layer target to initiate a temperature gradient and two picosecond time-resolved diagnostics to probe the surface expansion and heat flow. Comparison between the data and simulations using various EOSs and thermal conductivity models is quantified with a statistical χ^{2} analysis. Out of seven EOS tables and five thermal conductivity models, only L9061 with the Lee-More model provides a probability above 50% to match all data.

Smooth Flow in Diamond: Atomistic Ductility and Electronic Conductivity

Diamond is the quintessential superhard material widely known for its stiff and brittle nature and large electronic band gap. In stark contrast to these established benchmarks, our first-principles studies unveil surprising intrinsic structural ductility and electronic conductivity in diamond under coexisting large shear and compressive strains. These complex loading conditions impede brittle fracture modes and promote atomistic ductility, triggering rare smooth plastic flow in the normally rigid diamond crystal. This extraordinary structural change induces a concomitant band gap closure, enabling smooth charge flow in deformation created conducting channels. These startling soft-and-conducting modes reveal unprecedented fundamental characteristics of diamond, with profound implications for elucidating and predicting diamond's anomalous behaviors at extreme conditions.

Synthesis and High-Pressure Mechanical Properties of Superhard Rhenium/Tungsten Diboride Nanocrystals

Rhenium diboride is an established superhard compound that can scratch diamond and can be readily synthesized under ambient pressure. Here, we demonstrate two synergistic ways to further enhance the already high yield strength of ReB₂. The first approach builds on previous reports where tungsten is doped into ReB₂ at concentrations up to 48 at. %, forming a rhenium/tungsten diboride solid solution (Re_0.52W_0.48B₂). In the second approach, the composition of both materials is maintained, but the particle size is reduced to the nanoscale (40-150 nm). Bulk samples were synthesized by arc melting above 2500 °C, and salt flux growth at ∼850 °C was used to create nanoscale materials. In situ radial X-ray diffraction was then performed under high pressures up to ∼60 GPa in a diamond anvil cell to study mechanical properties including bulk modulus, lattice strain, and strength anisotropy. The differential stress for both Re_0.52W_0.48B₂ and nano ReB₂ (n-ReB₂) was increased compared to bulk ReB₂. In addition, the lattice-preferred orientation of n-ReB₂ was experimentally measured. Under non-hydrostatic compression, n-ReB₂ exhibits texture characterized by a maximum along the [001] direction, confirming that plastic deformation is primarily controlled by the basal slip system. At higher pressures, a range of other slip systems become active. Finally, both size and solid-solution effects were combined in nanoscale Re_0.52W_0.48B₂. This material showed the highest differential stress and bulk modulus, combined with suppression of the new slip planes that opened at high pressure in n-ReB₂.

Pseudoelasticity at Large Strains in Au Nanocrystals

Pseudoelasticity in metals is typically associated with phase transformations (e.g., shape memory alloys) but has recently been observed in sub-10 nm Ag nanocrystals that rapidly recovered their original shape after deformation to large strains. The discovery of pseudoelasticity in nanoscale metals dramatically changes the current understanding of the properties of solids at the smallest length scales, and the motion of atoms at surfaces. Yet, it remains unclear whether pseudoelasticity exists in different metals and nanocrystal sizes. The challenge of observing deformation at atomistic to nanometer length scales has prevented a clear mechanistic understanding of nanoscale pseudoelasticity, although surface diffusion and dislocation-mediated processes have been proposed. We further the understanding of pseudoelasticity in nanoscale metals by using a diamond anvil cell to compress colloidal Au nanocrystals under quasihydrostatic and nonhydrostatic pressure conditions. Nanocrystal structural changes are measured using optical spectroscopy and transmission electron microscopy and modeled using electrodynamic theory. We find that 3.9 nm Au nanocrystals exhibit pseudoelastic shape recovery after deformation to large uniaxial strains of up to 20%, which is equivalent to an ellipsoid with an aspect ratio of 2. Nanocrystal absorbance efficiency does not recover after deformation, which indicates that crystalline defects may be trapped in the nanocrystals after deformation.

First principles calculation of the nonhydrostatic effects on structure and Raman frequency of 3C-SiC

For understanding the quantitative effect of nonhydrostatic stress on properties of material, the crystal structure and Raman spectra of 3C-SiC under hydrostatic and nonhydrostatic stress were calculated using a first-principles method. The results show that the lattice constants (a, b, and c) under nonhydrostatic stresses deviate those under hydrostatic stress. The differences of the lattice constants under hydrostatic stress from nonhydrostatic stresses with differential stress were fitted by linear equation. Nonhydrostatic stress has no effect on density of 3C-SiC at high pressure, namely the equations of state of 3C-SiC under hydrostatic stress are same as those under nonhydrostatic stress. The frequencies and pressure dependences of LO and TO modes of 3C-SiC Raman spectra under nonhydrostatic stress are just same as those under hydrostatic stress. Under nonhydrostatic stress, there are four new lines with 361, 620, 740, and 803 cm⁻¹ appeared in the Raman spectra except for the LO and TO lines because of the reduction of structure symmetry. However the frequencies and pressure dependences of the four Raman modes remain unchanged under different nonhydrostatic stresses. Appearance of new Raman modes under nonhydrostatic stress and the linear relationship of the differences of lattice constants under hydrostatic and nonhydrostatic stresses with differential stress can be used to indicate state of stress in high pressure experiments. The effect of nonhydrostatic stress on materials under high pressure is complicated and our calculation would help to understanding state of stress at high pressure experiments.

Toroidal diamond anvil cell for detailed measurements under extreme static pressures

Over the past 60 years, the diamond anvil cell (DAC) has been developed into a widespread high static pressure device. The adaptation of laboratory and synchrotron analytical techniques to DAC enables a detailed exploration in the 100 GPa range. The strain of the anvils under high load explains the 400 GPa limit of the conventional DAC. Here we show a toroidal shape for a diamond anvil tip that enables to extend the DAC use toward the terapascal pressure range. The toroidal-DAC keeps the assets for a complete, reproducible, and accurate characterization of materials, from solids to gases. Raman signal from the diamond anvil or X-ray signal from the rhenium gasket allow measurement of pressure. Here, the equations of state of gold, aluminum, and argon are measured with X-ray diffraction. The data are compared with recent measurements under similar conditions by two other approaches, the double-stage DAC and the dynamic ramp compression.

Extreme static pressures exceeding a million atmospheres exist in a variety of natural environments, but obtaining such pressures in a laboratory is still a challenge. Here, the authors develop a toroidal diamond anvil design that allows for the generation of 600 GPa (6 million atmospheres) in routinely used diamond anvil cells.

High pressure phase transformations revisited

High pressure phase transformations play an important role in the search for new materials and material synthesis, as well as in geophysics. However, they are poorly characterized, and phase transformation pressure and pressure hysteresis vary drastically in experiments of different researchers, with different pressure transmitting media, and with different material suppliers. Here we review the current state, challenges in studying phase transformations under high pressure, and the possible ways in overcoming the challenges. This field is critically compared with fields of phase transformations under normal pressure in steels and shape memory alloys, as well as plastic deformation of materials. The main reason for the above mentioned discrepancy is the lack of understanding that there is a fundamental difference between pressure-induced transformations under hydrostatic conditions, stress-induced transformations under nonhydrostatic conditions below yield, and strain-induced transformations during plastic flow. Each of these types of transformations has different mechanisms and requires a completely different thermodynamic and kinetic description and experimental characterization. In comparison with other fields the following challenges are indicated for high pressure phase transformation: (a) initial and evolving microstructure is not included in characterization of transformations; (b) continuum theory is poorly developed; (c) heterogeneous stress and strain fields in experiments are not determined, which leads to confusing material transformational properties with a system behavior. Some ways to advance the field of high pressure phase transformations are suggested. The key points are: (a) to take into account plastic deformations and microstructure evolution during transformations; (b) to formulate phase transformation criteria and kinetic equations in terms of stress and plastic strain tensors (instead of pressure alone); (c) to develop multiscale continuum theories, and (d) to couple experimental, theoretical, and computational studies of the behavior of a tested sample to extract information about fields of stress and strain tensors and concentration of high pressure phase, transformation criteria and kinetics. The ideal characterization should contain complete information which is required for simulation of the same experiments.

Quantitative stress measurement of elastic deformation using mechanoluminescent sensor: An intensity ratio model

The mechanoluminescent (ML) sensor is a newly developed non-invasive technique for stress/strain measurement. However, its application has been mostly restricted to qualitative measurement due to the lack of a well-defined relationship between ML intensity and stress. To achieve accurate stress measurement, an intensity ratio model was proposed in this study to establish a quantitative relationship between the stress condition and its ML intensity in elastic deformation. To verify the proposed model, experiments were carried out on a ML measurement system using resin samples mixed with the sensor material SrAl₂O₄:Eu²⁺, Dy³⁺. The ML intensity ratio was found to be dependent on the applied stress and strain rate, and the relationship acquired from the experimental results agreed well with the proposed model. The current study provided a physical explanation for the relationship between ML intensity and its stress condition. The proposed model was applicable in various SrAl₂O₄:Eu²⁺, Dy³⁺-based ML measurement in elastic deformation, and could provide a useful reference for quantitative stress measurement using the ML sensor in general.

Diamond anvil cell behavior up to 4 Mbar

The diamond anvil cell (DAC) is considered one of the dominant devices to generate ultrahigh static pressure. The development of the DAC technique has enabled researchers to explore rich high-pressure science in the multimegabar pressure range. Here, we investigated the behavior of the DAC up to 400 GPa, which is the accepted pressure limit of a conventional DAC. By using a submicrometer synchrotron X-ray beam, double cuppings of the beveled diamond anvils were observed experimentally. Details of pressure loading, distribution, gasket-thickness variation, and diamond anvil deformation were studied to understand the generation of ultrahigh pressures, which may improve the conventional DAC techniques.

A laser heating facility for energy-dispersive X-ray absorption spectroscopy

A double-sided laser heating setup for diamond anvil cells installed on the ID24 beamline of the ESRF is presented here. The setup geometry is specially adopted for the needs of energy-dispersive X-ray absorption spectroscopic (XAS) studies of materials under extreme pressure and temperature conditions. We illustrate the performance of the facility with a study on metallic nickel at 60 GPa. The XAS data provide the temperature of the melting onset and quantitative information on the structural parameters of the first coordination shell in the hot solid up to melting.

Pressure Self-focusing Effect and Novel Methods for Increasing the Maximum Pressure in Traditional and Rotational Diamond Anvil Cells

The main principles of producing a region near the center of a sample, compressed in a diamond anvil cell (DAC), with a very high pressure gradient and, consequently, with high pressure are predicted theoretically. The revealed phenomenon of generating extremely high pressure gradient is called the pressure self-focusing effect. Initial analytical predictions utilized generalization of a simplified equilibrium equation. Then, the results are refined using our recent advanced model for elastoplastic material under high pressures in finite element method (FEM) simulations. The main points in producing the pressure self-focusing effect are to use beveled anvils and reach a very thin sample thickness at the center. We find that the superposition of torsion in a rotational DAC (RDAC) offers drastic enhancement of the pressure self-focusing effect and allows one to reach the same pressure under a much lower force and deformation of anvils.

High-pressure studies with x-rays using diamond anvil cells

Pressure profoundly alters all states of matter. The symbiotic development of ultrahigh-pressure diamond anvil cells, to compress samples to sustainable multi-megabar pressures; and synchrotron x-ray techniques, to probe materials' properties in situ, has enabled the exploration of rich high-pressure (HP) science. In this article, we first introduce the essential concept of diamond anvil cell technology, together with recent developments and its integration with other extreme environments. We then provide an overview of the latest developments in HP synchrotron techniques, their applications, and current problems, followed by a discussion of HP scientific studies using x-rays in the key multidisciplinary fields. These HP studies include: HP x-ray emission spectroscopy, which provides information on the filled electronic states of HP samples; HP x-ray Raman spectroscopy, which probes the HP chemical bonding changes of light elements; HP electronic inelastic x-ray scattering spectroscopy, which accesses high energy electronic phenomena, including electronic band structure, Fermi surface, excitons, plasmons, and their dispersions; HP resonant inelastic x-ray scattering spectroscopy, which probes shallow core excitations, multiplet structures, and spin-resolved electronic structure; HP nuclear resonant x-ray spectroscopy, which provides phonon densities of state and time-resolved Mössbauer information; HP x-ray imaging, which provides information on hierarchical structures, dynamic processes, and internal strains; HP x-ray diffraction, which determines the fundamental structures and densities of single-crystal, polycrystalline, nanocrystalline, and non-crystalline materials; and HP radial x-ray diffraction, which yields deviatoric, elastic and rheological information. Integrating these tools with hydrostatic or uniaxial pressure media, laser and resistive heating, and cryogenic cooling, has enabled investigations of the structural, vibrational, electronic, and magnetic properties of materials over a wide range of pressure-temperature conditions.

Superhard Monoborides: Hardness Enhancement through Alloying in W1- x Tax B

In tungsten monoboride (WB), the boron atoms are linked in parallel serpentine arrays, with tungsten atoms in between. This lattice is metallic, unlike conventional covalent superhard materials such as diamond or cubic boron nitride. By selectively substituting tungsten atoms with tantalum, the Vickers hardness can be increased to 42.8 GPa, creating a new superhard metal.

Fabrication of Diamond Based Sensors for Use in Extreme Environments

Electrical and magnetic sensors can be lithographically fabricated on top of diamond substrates and encapsulated in a protective layer of chemical vapor deposited single crystalline diamond. This process when carried out on single crystal diamond anvils employed in high pressure research is termed as designer diamond anvil fabrication. These designer diamond anvils allow researchers to study electrical and magnetic properties of materials under extreme conditions without any possibility of damaging the sensing elements. We describe a novel method for the fabrication of designer diamond anvils with the use of maskless lithography and chemical vapor deposition in this paper. This method can be utilized to produce diamond based sensors which can function in extreme environments of high pressures, high and low temperatures, corrosive and high radiation conditions. We demonstrate applicability of these diamonds under extreme environments by performing electrical resistance measurements during superconducting transition in rare earth doped iron-based compounds under high pressures to 12 GPa and low temperatures to 10 K.

Picosecond acoustics method for measuring the thermodynamical properties of solids and liquids at high pressure and high temperature

Based on the original combination of picosecond acoustics and diamond anvils cell, recent improvements to accurately measure hypersonic sound velocities of liquids and solids under extreme conditions are described. To illustrate the capability of this technique, results are given on the pressure and temperature dependence of acoustic properties for three prototypical cases: polycrystal (iron), single-crystal (silicon) and liquid (mercury) samples. It is shown that such technique also enables the determination of the density as a function of pressure for liquids, of the complete set of elastic constants for single crystals, and of the melting curve for any kind of material. High pressure ultrafast acoustic spectroscopy technique clearly opens opportunities to measure thermodynamical properties under previously unattainable extreme conditions. Beyond physics, this state-of-the-art experiment would thus be useful in many other fields such as nonlinear acoustics, oceanography, petrology, in of view. A brief description of new developments and future directions of works conclude the article.

Note: a novel method to measure the deformation of diamond anvils under high pressure

A novel and simple method based on optical-fiber frequency domain interferometer to measure the deformation of diamond anvils under high pressure is presented. The working principle and application examples are given in this paper. The deformation of diamond anvils is obtained up to 37.7 GPa, our results verify that the deformation has an obvious difference between uploading and downloading at a given pressure, the maximum difference is up to 4.5 μm at 18.8 GPa, and the cupping effect is observed directly.

Momentum-resolved resonant inelastic X-ray scattering on a single crystal under high pressure

A single-crystal momentum-resolved resonant inelastic X-ray scattering (RIXS) experiment under high pressure using an originally designed diamond anvil cell (DAC) is reported. The diamond-in/diamond-out geometry was adopted with both the incident and scattered beams passing through a 1 mm-thick diamond. This enabled us to cover wide momentum space keeping the scattering angle condition near 90°. Elastic and inelastic scattering from the diamond was drastically reduced using a pinhole placed after the DAC. Measurement of the momentum-resolved RIXS spectra of Sr2.5Ca11.5Cu24O41 at the Cu K-edge was thus successful. Though the inelastic intensity becomes weaker by two orders than the ambient pressure, RIXS spectra both at the center and the edge of the Brillouin zone were obtained at 3 GPa and low-energy electronic excitations of the cuprate were found to change with pressure.

Phase stability and elastic properties of (W0.5Al0.5)C phase with a novel NiAs-type structure

Using density-functional theory, we show that the NiAs-type is a more favorable structure for the (W_0.5Al_0.5)C phase than the experimentally proposed WC-type structure when we compare the thermodynamic, dynamic and elastic properties of the two types.

Solid iron compressed up to 560 GPa

Dynamic compression by multiple shocks is used to compress iron up to 560 GPa (5.6 Mbar), the highest solid-state pressure yet attained for iron in the laboratory. Extended x-ray absorption fine structure (EXAFS) spectroscopy offers simultaneous density, temperature, and local-structure measurements for the compressed iron. The data show that the close-packed structure of iron is stable up to 560 GPa, the temperature at peak compression is significantly higher than expected from pure compressive work, and the dynamic strength of iron is many times greater than the static strength based on lower pressure data. The results provide the first constraint on the melting line of iron above 400 GPa.

Design and performance of tapered cubic anvil used for achieving higher pressure and larger sample cell

In order to increase the maximum cell pressure of the cubic high pressure apparatus, we have developed a new structure of tungsten carbide cubic anvil (tapered cubic anvil), based on the principle of massive support and lateral support. Our results indicated that the tapered cubic anvil has some advantages. First, tapered cubic anvil can push the transfer rate of pressure well into the range above 36.37% compare to the conventional anvil. Second, the rate of failure crack decreases about 11.20% after the modification of the conventional anvil. Third, the limit of static high-pressure in the sample cell can be extended to 13 GPa, which can increase the maximum cell pressure about 73.3% than that of the conventional anvil. Fourth, the volume of sample cell compressed by tapered cubic anvils can be achieved to 14.13 mm(3) (3 mm diameter × 2 mm long), which is three and six orders of magnitude larger than that of double-stage apparatus and diamond anvil cell, respectively. This work represents a relatively simple method for achieving higher pressures and larger sample cell.

Combined resistive and laser heating technique for in situ radial X-ray diffraction in the diamond anvil cell at high pressure and temperature

To extend the range of high-temperature, high-pressure studies within the diamond anvil cell, a Liermann-type diamond anvil cell with radial diffraction geometry (rDAC) was redesigned and developed for synchrotron X-ray diffraction experiments at beamline 12.2.2 of the Advanced Light Source. The rDAC, equipped with graphite heating arrays, allows simultaneous resistive and laser heating while the material is subjected to high pressure. The goals are both to extend the temperature range of external (resistive) heating and to produce environments with lower temperature gradients in a simultaneously resistive- and laser-heated rDAC. Three different geomaterials were used as pilot samples to calibrate and optimize conditions for combined resistive and laser heating. For example, in Run#1, FeO was loaded in a boron-mica gasket and compressed to 11 GPa then gradually resistively heated to 1007 K (1073 K at the diamond side). The laser heating was further applied to FeO to raise temperature to 2273 K. In Run#2, Fe-Ni alloy was compressed to 18 GPa and resistively heated to 1785 K (1973 K at the diamond side). The combined resistive and laser heating was successfully performed again on (Mg0.9Fe0.1)O in Run#3. In this instance, the sample was loaded in a boron-kapton gasket, compressed to 29 GPa, resistive-heated up to 1007 K (1073 K at the diamond side), and further simultaneously laser-heated to achieve a temperature in excess of 2273 K at the sample position. Diffraction patterns obtained from the experiments were deconvoluted using the Rietveld method and quantified for lattice preferred orientation of each material under extreme conditions and during phase transformation.

Constitutive law and flow mechanism in diamond deformation

Constitutive laws and crystal plasticity in diamond deformation have been the subjects of substantial interest since synthetic diamond was made in 1950's. To date, however, little is known quantitatively regarding its brittle-ductile properties and yield strength at high temperatures. Here we report, for the first time, the strain-stress constitutive relations and experimental demonstration of deformation mechanisms under confined high pressure. The deformation at room temperature is essentially brittle, cataclastic, and mostly accommodated by fracturing on {111} plane with no plastic yielding at uniaxial strains up to 15%. At elevated temperatures of 1000°C and 1200°C diamond crystals exhibit significant ductile flow with corresponding yield strength of 7.9 and 6.3 GPa, indicating that diamond starts to weaken when temperature is over 1000°C. At high temperature the plastic deformation and ductile flow is meditated by the <110>{111} dislocation glide and a very active {111} micro-twinning.

Synchrotron infrared measurements of dense hydrogen to 360 GPa

Diamond-anvil-cell techniques have been developed to confine and measure hydrogen samples under static conditions to pressures above 300 GPa from 12 to 300 K using synchrotron infrared and optical absorption techniques. A decreasing absorption threshold in the visible spectrum is observed, but the material remains transparent at photon energies down to 0.1 eV at pressures to 360 GPa over a broad temperature range. The persistence of the strong infrared absorption of the vibron characteristic of phase III indicates the stability of the paired state of hydrogen. There is no evidence for the predicted metallic state over these conditions, in contrast to recent reports, but electronic properties consistent with semimetallic behavior are observed.

Application of a new composite cubic-boron nitride gasket assembly for high pressure inelastic x-ray scattering studies of carbon related materials

We have developed a new composite cubic-boron nitride (c-BN) gasket assembly for high pressure diamond anvil cell studies, and applied it to inelastic x-ray scattering (IXS) studies of carbon related materials in order to maintain a larger sample thickness and avoid the interference from the diamond anvils. The gap size between the two diamond anvils remained ~80 μm at 48.0 GPa with this new composite c-BN gasket assembly. The sample can be located at the center of the gap, ~20 μm away from the surface of both diamond anvils, which provides ample distance to separate the sample signal from the diamond anvils. The high pressure IXS of a solvated C(60) sample was studied up to 48 GPa, and a pressure induced bonding transition from sp(2) to sp(3) was observed at 27 GPa.

Nanoprobe measurements of materials at megabar pressures

The use of nanoscale x-ray probes overcomes several key limitations in the study of materials up to multimegabar (> 200) pressures, namely, the spatial resolution of measurements of multiple samples, stress gradients, and crystal domains in micron to submicron size samples in diamond-anvil cells. Mixtures of Fe, Pt, and W were studied up to 282 GPa with 250-600 nm size synchrotron x-ray absorption and diffraction probes. The probes readily resolve signals from individual materials, between sample and gasket, and peak pressures, in contrast to the 5-microm-sized x-ray beams that are now becoming routine. The use of nanoscale x-ray beams also enables single-crystal x-ray diffraction studies in nominally polycrystalline samples at ultrahigh pressures, as demonstrated in measurements of (Mg,Fe)SiO(3) postperovskite. These capabilities have potential for driving a push toward higher maximum pressures and further miniaturization of high-pressure devices, in the process advancing studies at extreme conditions.

Experimental method for in situ determination of material textures at simultaneous high pressure and high temperature by means of radial diffraction in the diamond anvil cell

We introduce the design and capabilities of a resistive heated diamond anvil cell that can be used for side diffraction at simultaneous high pressure and high temperature. The device can be used to study lattice-preferred orientations in polycrystalline samples up to temperatures of 1100 K and pressures of 36 GPa. Capabilities of the instrument are demonstrated with preliminary results on the development of textures in the bcc, fcc, and hcp polymorphs of iron during a nonhydrostatic compression experiment at simultaneous high pressure and high temperature.

High quality x-ray absorption spectroscopy measurements with long energy range at high pressure using diamond anvil cell

We describe an approach for acquiring high quality x-ray absorption fine structure (XAFS) spectroscopy spectra with wide energy range at high pressure using diamond anvil cell (DAC). Overcoming the serious interference of diamond Bragg peaks is essential for combining XAFS and DAC techniques in high pressure research, yet an effective method to obtain accurate XAFS spectrum free from DAC induced glitches has been lacking. It was found that these glitches, whose energy positions are very sensitive to the relative orientation between DAC and incident x-ray beam, can be effectively eliminated using an iterative algorithm based on repeated measurements over a small angular range of DAC orientation, e.g., within +/-3 degrees relative to the x-ray beam direction. Demonstration XAFS spectra are reported for rutile-type GeO2 recorded by traditional ambient pressure and high pressure DAC methods, showing similar quality at 440 eV above the absorption edge. Accurate XAFS spectra of GeO2 glass were obtained at high pressure up to 53 GPa, providing important insight into the structural polymorphism of GeO2 glass at high pressure. This method is expected be applicable for in situ XAFS measurements using a diamond anvil cell up to ultrahigh pressures.

Synchrotron infrared reflectivity measurements of iron at high pressures

The infrared reflectance of iron was studied using high-pressure synchrotron radiation methods up to 50 GPa at room temperature in a diamond anvil cell of 1000-8000 cm(-1) (1.25-10 microm). The magnitude of the reflectivity shows a weak pressure dependence up to the transition from the body centered cubic (alpha) to hexagonal close packed (epsilon) phase transition, where a discontinuous change in both the slope and magnitude of the reflectivity was observed. Reflectance spectra were corrected for diamond absorption and treated with a Kramers-Kronig analysis to extract the optical constants; the emissivity of iron was derived from Kirchoff's law. The pressure and wavelength dependence of the emissivity is characterized by an empirical function for 1.5-1.9 microm; this wavelength range is useful for spectroradiometric temperature measurements from 1000 K up to approximately 2500 K. Alpha-Fe is a nonideal emitter; however, epsilon-Fe behaves as an almost perfect greybody in the infrared up to the highest pressures of the measurements. Temperature measurements based on the spectroradiometry of iron samples should take into account the wavelength dependent emissivity below the alpha-epsilon phase transition at approximately 13 GPa.

Osmium metal studied under high pressure and nonhydrostatic stress

Interest in osmium as an ultra-incompressible material and as an analog for the behavior of iron at high pressure has inspired recent studies of its mechanical properties. We have measured elastic and plastic deformation of Os metal at high pressures using in situ high pressure x-ray diffraction in the radial geometry. We show that Os has the highest yield strength observed for any pure metal, supporting up to 10 GPa at a pressure of 26 GPa. Furthermore, our data indicate changes in the nonhydrostatic apparent c/a ratio and clear lattice preferred orientation effects at pressures above 15 GPa.

Density measurements of noncrystalline materials at high pressure with diamond anvil cell

We describe an x-ray absorption method for in situ density measurement of non-crystalline materials in the diamond anvil cell using a monochromatic synchrotron x-ray microbeam. Sample thickness, which is indispensable in the absorption method, can be determined precisely by extrapolating the thickness profile of the gasket obtained by x-ray absorption and diffraction measurements. Diamond deformation across the sample chamber becomes noticeable at high pressures above 10 GPa, which can be monitored with a precision better than 1%, as demonstrated by measurements on crystalline Ag. We have applied the developed method to measure densities of the classic network-forming GeO(2) glass in octahedral form at pressures up to 56 GPa. The fit to the pressure-volume data with the Birch-Murnaghan equation from 13 to 56 GPa gives parameters of V(0)=23.2+/-0.4 cm(3)mol and K=35.8+/-3.0 GPa, assuming that K(')=4. This method could be applicable for in situ determination of the density of liquids and other noncrystalline materials using a diamond anvil cell up to ultrahigh pressures.

Thickness measurement of sample in diamond anvil cell

We report on an original method that measures sample thickness in a diamond anvil cell under high pressures. The method is based on two hypotheses: completely plastic deformation on the gasket and completely elastic deformation of the diamonds. This method can further eliminate the effect of diamond deformation on the thickness measurement of a sample, which permits us to measure the thickness of alumina up to 41.4 GPa.