Activated sludge microbial community assembly: the role of influent microbial community immigration

Wastewater treatment plants (WWTPs) are host to diverse microbial communities and receive a constant influx of microbes from influent wastewater. However, the impact of immigrants on the structure and activities of the activated sludge (AS) microbial community remains unclear. To gain insight on this phenomenon known as perpetual community coalescence, the current study utilized controlled manipulative experiments that decoupled the influent wastewater composition from the microbial populations to reveal the fundamental mechanisms involved in immigration between sewers and AS-WWTP. The immigration dynamics of heterotrophs were analyzed by harvesting wastewater biomass solids from three different sewer systems and adding to synthetic wastewater. Immigrating influent populations were observed to contribute up to 14% of the sequencing reads in the AS. By modeling the net growth rate of taxa, it was revealed that immigrants primarily exhibited low or negative net growth rates. By developing a protocol to reproducibly grow AS-WWTP communities in the lab, we have laid down the foundational principles for the testing of operational factors creating community variations with low noise and appropriate replication. Understanding the processes that drive microbial community diversity and assembly is a key question in microbial ecology. In the future, this knowledge can be used to manipulate the structure of microbial communities and improve system performance in WWTPs.IMPORTANCEIn biological wastewater treatment processes, the microbial community composition is essential in the performance and stability of the system. This study developed a reproducible protocol to investigate the impact of influent immigration (or perpetual coalescence of the sewer and activated sludge communities) with appropriate reproducibility and controls, allowing intrinsic definitions of core and immigrant populations to be established. The method developed herein will allow sequential manipulative experiments to be performed to test specific hypothesis and optimize wastewater treatment processes to meet new treatment goals.

Separation of nutrients from SCFAs with a dynamic membrane in a sludge anaerobic fermenter

The complexity and high cost to separate and recover short chain fatty acids (SCFAs), ammonium ions, and phosphates in the sludge fermentation liquid hinder the application of sludge anaerobic fermentation. In this study, an interesting phenomenon was found in a sludge anaerobic fermenter with a dynamic membrane (DM) which could not only enhance SCFAs production but also retain most SCFAs in fermenter. The separation factor of DM for NH3-N/SCFAs and PO43-/SCFAs throughout the DM development were about 40 and 80, respectively. Analysis reveals that rejection of SCFAs by DM could not be simply correlated to molecular weight or membrane pore size. The rejection mechanisms might be dominated by Donnan rejection. In addition, biodegradation in the DM may also have contribution. Findings of this study suggest the potential of DM as an economical technology for nutrients and SCFAs recover.

Effectiveness of a novel composite filler to enhance phosphorus removal in constructed wetlands

Improving the adsorption performance of wetland fillers is of great significance for enhancing pollutant removal in constructed wetlands. Currently, limited by complex preparation processes and high costs, large numbers of high adsorption fillers studied in lab are difficult to be applied in practical engineering. In this study, a newly low-cost and efficient phosphorus removal composite wetland filler (CFB) is prepared by using industrial and agriculture waste (steel slag and oyster shells) and natural ore (volcanic rock) as raw materials. The results show that phosphorus removal efficiency was largely enhanced by synergistic effects of steel slag, oyster shells, and volcanic rock, and it was mainly influenced by the proportion of each component of CFB. Based on the fitting of the classical isothermal equation, the adsorption capacity of CFB is 18.339 mg/g. The adsorption of phosphorus by CFB is endothermic and spontaneous, and there are heterogeneous surfaces and multi-layer adsorption processes, as well as pH value and temperature, are free from the influence on CFB phosphorus removal. During the practical wastewater application experiments, the phosphorus removal rate of the CFB-filled constructed wetland apparatus (CW-A) can reach 94.89% and is free from the influence on the removal of other pollutants (COD, TN, and NH3-N) by the system. Overall, the prepared CFB is of excellent decontamination effect, an extremely simple preparation process, low cost, and sound practical engineering application potential, providing new ideas and approaches for enhancing the phosphorus removal capacity and waste resource utilization of constructed wetland systems.

New insight into the granule formation in the reactor for enhanced biological phosphorus removal

While granulated activated sludge exhibits high productivity, the processes of granule formation are incompletely studied. The processes of granule formation and succession of communities were investigated in a laboratory sequencing batch reactor (SBR) under conditions for enhanced biological phosphorus removal (EBPR) using microbiological and molecular techniques. Active consumption of acetate, primarily by the phosphate-accumulating organisms (PAO), commenced at day 150 of cultivation. This was indicated by the high ratio of molar P-released/acetate uptake (0.73-0.77 P-mol/C-mol), characteristic of PAO. During this period, two types of granule-like aggregates formed spontaneously out of the activated sludge flocs. The aggregates differed in morphology and microbial taxonomic composition. While both aggregate types contained phosphorus-enriched bacterial cells, PAO prevailed in those of morphotype I, and glycogen-accumulating organisms (GAOs) were predominant in the aggregates of morphotype II. After 250 days, the elimination of the morphotype II aggregates from the reactor was observed. The subsequent selection of the community was associated with the development of the morphotype I aggregates, in which the relative abundance of PAO increased significantly, resulting in higher efficiency of phosphorus removal. Metagenomic analysis revealed a predominance of the organisms closely related to Candidatus Accumulibacter IС and IIС and of Ca. Accumulibacter IIB among the PAO. Based on the content of the genes of the key metabolic pathways, the genomes of potential PAO belonging to the genera Amaricoccus, Azonexus, Thauera, Zoogloea, Pinisolibacter, and Siculibacillus were selected. The patterns of physicochemical processes and the microbiome structure associated with granule formation and succession of the microbial communities were revealed.

Isolation and optimisation of polyphosphate accumulating bacteria for bio-treatment of phosphate from industrial wastewater

Phosphorus in wastewater influents is a global issue. Controlling eutrophic water is crucial. Biological phosphorus removal is an economically and environmentally sustainable method for removing phosphorus from wastewater. This study aims to isolate and improve the capacity of aerobic phosphorus-removing bacteria to reduce excessive phosphate concentrations in the environment. Only three out of fourteen bacterial isolates demonstrated the highest phosphate removal efficiency using Toluidine blue-O. Klebsiella pneumoniae 6A, Klebsiella quasipneumoniae 6R, and Enterobacter mori 8R were isolated from activated sludge and identified by 16srRNA. In a single-factor experiment, the effect of incubation periods, phosphate concentrations, carbon sources, sodium acetate concentrations, temperature, pH, and irradiation dosages were studied. Seventy-two hours of incubation, 55 mg/L PO4, sodium acetate as the carbon source, 30°C and pH 7 resulted in maximum phosphorus removal. After optimising the parameters, the removal efficiency of Klebsiella pneumoniae 6A, Klebsiella quasipneumoniae 6R, and Enterobacter mori 8R increased from 73.5% to 85.1%, 79.1% to 98.1%, and 80.6% to 91.9%, respectively. Gamma irradiation showed significant results only in Klebsiella pneumoniae 6A where 100 Gy increased the phosphorous removal efficiency from 85.1% to 100%. Immobilised mixed culture of the three strains adapted better to 100 mg/L Phosphorus than pure cells. Therefore, this technique holds great new promise for phosphorus-contaminated sites bioremediation.

Seasonal prevalence of bacteria in the outflow of two full-scale municipal wastewater treatment plants

Despite many modern wastewater treatment solutions, the most common is still the use of activated sludge (AS). Studies indicate that the microbial composition of AS is most often influenced by the raw sewage composition (especially influent ammonia), biological oxygen demand, the level of dissolved oxygen, technological solutions, as well as the temperature of wastewater related to seasonality. The available literature mainly refers to the relationship between AS parameters or the technology used and the composition of microorganisms in AS. However, there is a lack of data on the groups of microorganisms leaching into water bodies whose presence is a signal for possible changes in treatment technology. Moreover, sludge flocs in the outflow contain less extracellular substance (EPS) which interferes microbial identification. The novelty of this article concerns the identification and quantification of microorganisms in the AS and in the outflow by fluorescence in situ hybridization (FISH) method from two full-scale wastewater treatment plants (WWTPs) in terms of 4 key groups of microorganisms involved in the wastewater treatment process in the context of their potential technological usefulness. The results of the study showed that Nitrospirae, Chloroflexi and Ca. Accumulibacter phosphatis in treated wastewater reflect the trend in abundance of these bacteria in activated sludge. Increased abundance of betaproteobacterial ammonia-oxidizing bacteria and Nitrospirae in the outflow were observed in winter. Principal component analysis (PCA) showed that loadings obtained from abundance of bacteria in the outflow made larger contributions to the variance in the PC1 factorial axis, than loadings obtained from abundance of bacteria from activated sludge. PCA confirmed the reasonableness of conducting studies not only in the activated sludge, but also in the outflow to find correlations between technological problems and qualitative and quantitative changes in the outflow microorganisms.

Nutrients removal by Olivibacter jilunii immobilized on activated carbon for aquaculture wastewater treatment: ppk1 gene and bacterial community structure

In this study, immobilized biological activated carbon (IBAC) mediated with Olivibacter jilunii (strain PAO-9) was utilized to treat aquaculture wastewater for nutrients removal. IBAC with strain PAO-9 could load the greatest ppk1 gene copy numbers (129524.6) per gram on activated carbon at 28 °C for 2 d in 120 rpm of stirring speed and 2 d in stationary condition. Moreover, the results about the nutrients removal and microbiology community structure showed that strain PAO-9 on IBAC could alter the structure and diversity of microbial communities and then promoted to remove the total phosphorus and total nitrogen of eel aquaculture wastewater. The highest total phosphorus, chemical oxygen demand, ammonia and total nitrogen of the wastewater treated by strain PAO-9 on IBAC were 96.1 %, 98.0 %, 100.0 % and 97.4 %, respectively. In all, O. jilunii PAO-9 immobilized activated carbon was a potential and effective approach to remove the nutrients of eel aquaculture wastewater.

Composition and biodiversity of soil and root-associated microbiome in Vitis vinifera cultivar Lambrusco distinguish the microbial terroir of the Lambrusco DOC protected designation of origin area on a local scale

Introduction

Wines produced from the same grape cultivars but in different locations possess distinctive qualities leading to different consumer's appreciation, preferences, and thus purchase choices. Here, we explore the possible importance of microbiomes at the soil-plant interface as a determinant of the terroir properties in grapevine production, which confer specific growth performances and wine chemo-sensory properties at the local scale.

Methods

In particular, we investigated the variation in microbial communities associated with the roots of Vitis vinifera cultivar Lambrusco, as well as with surrounding bulk soils, in different vineyards across the "Consorzio Tutela Lambrusco DOC" protected designation of origin area (PDO, Emilia Romagna, Italy), considering viticultural sites located both inside and outside the consortium in two different seasons (June and November 2021).

Results

According to our findings, rhizospheric and soil microbiomes show significant structural differences in relation to the sampling site, regardless of seasonality, while endophytic microbiomes seem to be completely unaffected by such variables. Furthermore, a deeper insight into the microbial terroir of PDO areas highlighted the presence of some rhizospheric microorganisms enriched inside the consortium and characterizing the PDO regardless of both sampling season and farming strategy. These include Bacillus, Paenibacillus, and Azospirillum, which are all well-known plant growth-promoting bacteria.

Discussion

Taken together, our results suggest a connection between soil and root microbiomes of V. vinifera cultivar Lambrusco and the local designation of origin, emphasizing the potential role of PDO-enriched plant growth-promoting bacteria in vine growing and final quality of the Lambrusco DOC wine.

Carbon dissipation from surgical cotton production wastewater using macroalgae, microalgae, and activated sludge microbes

Surgical cotton production has drastically been increased in the past few years due to excessive use by medical health professionals especially in countries like India, which is among the top three exporters of cotton worldwide. The effluent generated from surgical cotton industries differ from textile effluents by the conspicuous absence of dyeing chemicals. This wastewater has a high concentration of suspended particles, COD, dissolved ions, organic carbon, and alkaline pH. Several studies have been published on the treatment of textile effluents and the degradation of dyeing chemicals, while the treatment studies on surgical cotton wastewater have been rarely reported in spite of their potential to cause pollution in receiving land/water bodies. Activated sludge microbes have been extensively studied and well documented in the treatment of several industrial effluent but does not match to the production of valuable biomass from algae. The global energy demand has prompted the scientific community to investigate and explore the possibility of using algae for energy production with simultaneous wastewater treatment. To the best of the authors' knowledge, no research articles have been published which compare the effectiveness of activated sludge microorganisms, microalgae, and macroalgae in removing contaminants from real wastewater. To date, there is a knowledge gap in understanding and selecting the right choice of biological system for effective and economical effluent treatment. In an attempt to minimize this gap, carbon removal by microalgae, macroalgae, and activated sludge microbes were investigated on real effluent from surgical cotton industries. It was observed that the strain of Chlorella vulgaris could dissipate 83% of COD from real wastewater, while consortia of macroalgae (consisting predominantly of Ulvaceae and Chaetomorpha) and activated sludge microbes could remove 81% and 69% of the carbon, respectively. The microalgal growth (in terms of wet weight) increased from 0.15 to 0.3 g, whereas the macroalgal wet weight increased from 1.5 to 3 g in over 7 days of batch experiments conducted in triplicates. This indicated the superlative performance of microalgae over activated sludge microbes in carbon dissipation.

Strategies for enhancing phosphorous removal in Vertical Flow Constructed Wetlands

Constructed wetlands (CWs) are among the fastest emerging treatment methods for wastewater treatment. Unlike their organics and nitrogen removal capacities, the potential of CWs as a sink for phosphorous is still debatable. In this study, the secondary data from several CWs treating domestic sewage were compiled and assessed. Curves were plotted between orthophosphate-phosphorous (PO₄^3--P) loading and the corresponding removal rates. Other factors affecting PO₄^3--P removal like depth of the CW, surface area, organic loading rate etc. Were also analyzed. Removal rates of PO₄^3--P were conforming to a linear positive relation with the loading rates. Pea gravel as a CW medium performed consistently well (60-80% removal) for a wide range of influent PO₄^3--P loading (0.5-1.5 g/m³-d). The increased depth of the wetland appears to favor phosphate removal. PO₄^3--P removal was found to be correlated with outlet dissolved oxygen, total Kjeldahl nitrogen removal and effluent nitrate. The study suggests that proper design, optimal organic loading and suitable pre-treatment may increase the applicability of CWs for phosphate removal from domestic wastewater. Larger area requirements can also be avoided by increasing their depth while keeping the volume of the filter media the same.

Phosphorus removal and recovery: state of the science and challenges

Phosphorus is one of the main nutrients required for all life. Phosphorus as phosphate form plays an important role in different cellular processes. Entrance of phosphorus in the environment leads to serious ecological problems including water quality problems and soil pollution. Furthermore, it may cause eutrophication as well as harmful algae blooms (HABs) in aquatic environments. Several physical, chemical, and biological methods have been presented for phosphorus removal and recovery. In this review, there is an overview of phosphorus role in nature provided, available removal processes are discussed, and each of them is explained in detail. Chemical precipitation, ion exchange, membrane separation, and adsorption can be listed as the most used methods. Identifying advantages of these technologies will allow the performance of phosphorus removal systems to be updated, optimized, evaluate the treatment cost and benefits, and support select directions for further action. Two main applications of biochar and nanoscale materials are recommended.

Phosphorus mining from eutrophic marine environment towards a blue economy: The role of bio-based applications

Global phosphorus reserves are under pressure of depletion in the near future due to increased consumption of primary phosphorus reservoirs and improper management of phosphorus. At the same time, a considerable portion of global marine water bodies has been suffering from eutrophication due to excessive nutrient loading. The marine environment can be considered as a valuable phosphorus source due to nutrient rich eutrophic seawater and sediment which could potentially serve as phosphorus mines in the near future. Hence, sustainable phosphorus recovery strategies should be adapted for marine systems to provide phosphorus for the growing market demand and simultaneously control eutrophication. In this review, possible sustainable strategies for phosphorus removal and recovery from marine environments are discussed in detail. Bio-based strategies relying on natural phosphorus uptake/release metabolism of living organisms are suggested as promising options that can provide both phosphorus removal and recovery from marine waters for achieving a sustainable marine ecosystem. Among them, the utilization of microorganisms seems promising to develop novel strategies. However, the research gap for the technical applicability of these strategies is still considerably big. Therefore, future research should focus on the technical development of the strategies through laboratory and/or field studies. Coupling phosphorus mining with other valorisation pathways (i.e., metal recovery, energy production) is also suggested to improve overall sustainability and economic viability. Environmental, economic and societal challenges should altogether be well addressed prior to real scale applications.

Designing the vertical flow constructed wetland based on targeted limiting pollutant

The requirement of large land area limits the adoption of constructed wetlands (CWs) in urban settings with limited land availability. The area calculations for CW design are commonly carried out following Kikuth approach where the removal rate constant (K) is derived from literature. Investigation of secondary data of 82 vertical flow CWs, performed in this study, yielded wide variations (0.0003 - 0.822 md^-1) in the calculated K values for different pollutants under different environmental and operational conditions indicating that it is important to incorporate the desired levels of pollutant removal to arrive at customized design of CWs. The results indicated that the relative standard deviation of K values could be narrowed by classifying the datasets based on design parameters like depth, hydraulic loading rates and substrate loading rates. These calculations can help arrive at more scientific design of CW to achieve the prevailing standards for the discharge or reuse of sewage.

Microbial storage and its implications for soil ecology

Organisms throughout the tree of life accumulate chemical resources, in particular forms or compartments, to secure their availability for future use. Here we review microbial storage and its ecological significance by assembling several rich but disconnected lines of research in microbiology, biogeochemistry, and the ecology of macroscopic organisms. Evidence is drawn from various systems, but we pay particular attention to soils, where microorganisms play crucial roles in global element cycles. An assembly of genus-level data demonstrates the likely prevalence of storage traits in soil. We provide a theoretical basis for microbial storage ecology by distinguishing a spectrum of storage strategies ranging from surplus storage (storage of abundant resources that are not immediately required) to reserve storage (storage of limited resources at the cost of other metabolic functions). This distinction highlights that microorganisms can invest in storage at times of surplus and under conditions of scarcity. We then align storage with trait-based microbial life-history strategies, leading to the hypothesis that ruderal species, which are adapted to disturbance, rely less on storage than microorganisms adapted to stress or high competition. We explore the implications of storage for soil biogeochemistry, microbial biomass, and element transformations and present a process-based model of intracellular carbon storage. Our model indicates that storage can mitigate against stoichiometric imbalances, thereby enhancing biomass growth and resource-use efficiency in the face of unbalanced resources. Given the central roles of microbes in biogeochemical cycles, we propose that microbial storage may be influential on macroscopic scales, from carbon cycling to ecosystem stability.

The Influence of Different Operation Conditions on the Treatment of Mariculture Wastewater by the Combined System of Anoxic Filter and Membrane Bioreactor

The mariculture wastewater treatment performance for the combined system of anoxic filter and membrane bioreactor (AF-MBR) was investigated under different hydraulic retention times (HRTs), influent alkalinity, and influent ammonia nitrogen load. The results showed that the removal efficiencies of TOC and total nitrogen were slightly better at the HRT of 8 h than at other HRTs, and the phosphate removal efficiency decreased with the increase of HRT. With the increase of influent alkalinity, the removal of TOC and phosphate did not change significantly. With the increase of influent alkalinity from 300 mg/L to 500 mg/L, the total nitrogen removal efficiency of AF-MBR was improved, but the change of the removal efficiency was not obvious when the alkalinity increased from 500 mg/L to 600 mg/L. When the influent concentration of ammonia nitrogen varied from 20 mg/L to 50 mg/L, the removal efficiencies of TOC, phosphate, and total nitrogen by AF-MBR were stable. An interesting finding was that in all the different operation conditions examined, the treatment efficiency of AF-MBR was always better than that of the control MBR. The concentrations of NO₃⁻-N in AF-MBR were relatively low, whereas NO₃⁻-N accumulated in the control MBR. The reason was that the microorganisms attached to the carrier and remained fixed in the aerobic and anoxic spaces, so that there was a gradual enrichment of bacteria characterized by slow growth in a high-salt environment. In addition, the microorganisms could gather and grow on the carrier forming a biofilm with higher activity, a richer and more stable population, and enhanced ability to resist a load impact.

The dynamics of phosphorus fractions and the factors driving phosphorus cycle in Zoige Plateau peatland soil

Phosphorus (P) is an essential nutrient, limiting plant growth and microbial activity in many ecosystems. However, a few studies have been conducted to investigate P dynamics and the factors driving P dynamics in peatland soils. Therefore, this study chose Zoige Plateau peatland (the largest peatland in China) to reveal P dynamics and the possible driving factors through fractionating soil P and investigating a series of abiotic and biotic factors. It is found that season, peatland type, and soil depth could strongly affect P dynamics. H₂O-P and NaHCO₃-P (labile P) had lower content, while NaOH-P, HCl-P, Mix-P, and Residual-P (non-labile P) were the dominant fractions. Besides, the sum of P fractions was higher than the traditional measurement of total P, suggesting P storage might be underestimated in peatland soils. Moreover, it is observed that biotic factors affected P fractions more than abiotic factors, and fungi affected refractory P more than bacteria. This study provides essential information for understanding P cycling in peatland soils and emphasizes specific microbes related to P cycling, which should be paid more attention to in the future.

Application of floating treatment wetlands for stormwater runoff: A critical review of the recent developments with emphasis on heavy metals and nutrient removal

Floating treatment wetlands (FTWs) are increasingly gaining popularity due to a set of valuable features like wastewater remediation under varied conditions, ecosystem quality preservation, landscape conservation, and aesthetic benefits. FTW is a phyto-technology in which macrophytes grow on a floating raft with their roots in permanent contact with water and remove pollutants via several physicochemical-biological processes. FTW is highly capable of overcoming technical and operational challenges that come way in stormwater treatment due to the erratic nature of hydrologic and input pollutant loads because this innovative buoyant hydroponic design can move up and down with fluctuating water levels in the stormwater pond and can treat highly variable flows. Plants and biofilms attached to the roots hanging beneath the floating mat play a pivotal role in FTWs. The present review encompasses the concept of FTWs, their structural designs, relevance in stormwater management, and mechanism of plant uptake for pollutant removal. The role of FTWs to remove heavy metals and nutrients is also critically analyzed. Understanding hydraulics and other parameters of FTW is vital to effective design. Hence, the role of vegetation coverage, vegetation type, sorption media, aeration frequency, and intensity, and plant density to enhance system efficiency is also highlighted. Due to their operational flexibility and environmentally friendly working with no additional burden on existing urban land use, FTWs entice broad international interest and offer a coherent solution for stormwater management. MAIN FINDINGS: The review delivers state-of-the-art analysis of the current understanding of hydraulics and other parameters of FTWs, and associated mechanisms to enhance the treatment efficiency of FTWs for nutrients and heavy metals removal.

Removal of Nitrogen and Phosphorus from Thickening Effluent of an Urban Wastewater Treatment Plant by an Isolated Green Microalga

Microalgae are photosynthetic microorganisms and are considered excellent candidates for a wide range of biotechnological applications, including the removal of nutrients from urban wastewaters, which they can recover and convert into biomass. Microalgae-based systems can be integrated into conventional urban wastewater treatment plants (WW-TP) to improve the water depuration process. However, microalgal strain selection represents a crucial step for effective phytoremediation. In this work, a microalga isolated from the effluent derived from the thickening stage of waste sludge of an urban WW-TP was selected and tested to highlight its potential for nutrient removal. Ammonium and phosphate abatements by microalgae were evaluated using both the effluent and a synthetic medium in a comparative approach. Parallelly, the isolate was characterized in terms of growth capability, morphology, photosynthetic pigment content and photosystem II maximum quantum yield. The isolated microalga showed surprisingly high biomass yield and removal efficiency of both ammonium and phosphate ions from the effluent but not from the synthetic medium. This suggests its clear preference to grow in the effluent, linked to the overall characteristics of this matrix. Moreover, biomass from microalgae cultivated in wastewater was enriched in photosynthetic pigments, polyphosphates, proteins and starch, but not lipids, suggesting its possible use as a biofertilizer.

Bacterial diversity in aqueous/sludge phases within diesel fuel storage tanks

Diesel fuel storage tanks are not hostile environments for microorganisms and tend to form sludges in the water deposited at the bottom of the tanks. The lack of nutrient, carbon and energy limitations within these habitats boost the abundance and the metabolic activity of microorganisms providing microbial hotspots with high growing rates of diesel degradation (0.10 ± 0.021 d^-1). Five different Phyla (Thermotogae, Spirochaetes, Firmicutes, Bacteroidetes Proteobacteria) were identified within the aqueous/sludge phase from in situ diesel storage tanks, by cultured independent molecular surveys using the 16S rDNA gene fragment. The identified dominant strains were Geotoga aestuarianus, Flavobacterium ceti, Spirochaeta thermophila, Propionispira arboris, Sporobacterium olearium and Dysgonomonas genera. The altitude where the storage tanks are located and the organic carbon concentration within the aqueous/sludge phases affected the bacterial diversity. Therefore, the more diverse the microbial communities are, the more probability of the presence of bacteria with capacity to metabolized diesel and eliminate organic matter. Despite, only phosphate showed an effect on the bacterial distribution within the storage tanks, there was an apparent lack of deterministic process in structuring microbial communities. Consequently, preventative protocols are a priority to avoid the microbial growth within diesel fuel storage tanks. A new focus of this worldwide problem within the oil industry would be to explore deeply the wide range of metabolic and adaptive capacities of these microorganisms. These microbial consortia are potential tools with new specific services to apply in bioremediation among others.

Simultaneous nitrification-denitrification by phosphate accumulating microorganisms

Nitrogen and phosphorous are important inorganic water pollutants that pose a major threat to the environment and health of both humans and animals. The physical and chemical ways to remove these pollutants from water and soil are expensive and harsh, so biological removal becomes the method of choice to alleviate the problem without any side effects. The identification of microorganisms capable of simultaneous heterotrophic nitrification and aerobic denitrification has greatly simplified the sequestration of nitrogen from ammonium (NH₄⁺) into dinitrogen (N₂). Further, the discovery of phosphorous accumulating organisms offers greater economic benefits because these organisms can favourably and simultaneously remove both nitrogen and phosphorous from wastewaters hence reducing the nutrient burden. The stability of the system and removal efficiency of inorganic pollutants can be enhanced by the use of immobilized organisms. However, limited work has been done so far in this direction and there is a need to further the efforts towards refining process efficiency by testing low-cost substrates and diverse microbial populations for the total eradication of these contaminants from wastewaters.