Asphaltenes from Heavy Crude Oil as Ultraviolet Stabilizers against Polypropylene Aging

The destruction of polymers under the influence of ultraviolet (UV) radiation is the cause of their aging and deterioration of strength properties. Asphaltenes are low-value waste products after the refining and deasphalting of heavy crude oil, which absorb UV radiation well. Asphaltenes require rational utilization, which suggests their use as UV stabilizing agents for polymers. In this work, asphaltenes were used to prevent UV aging of polypropylene (PP) by adding them in a mass fraction from 5% to 30% within an asphaltene/PP composite material. Rheometry, calorimetry, X-ray diffraction analysis, and tensile strength of PP films containing asphaltenes were performed before and after their intense UV irradiation for accelerated aging. Asphaltenes slightly reduce the viscosity, crystallinity, and mechanical strength of the initial PP due to their plasticizing effect. However, this deterioration in properties is more than compensated when studying UV-aged samples. Intense UV aging causes multiple catastrophic drops in the viscosity and strength of pure PP with the preservation of crystallinity due to the break of polymer chains and a decrease in molecular weight by approximately eight times. Asphaltenes suppress the destruction of PP, which is expressed in a significantly smaller decline in its viscosity and strength due to UV aging. The most optimal content of asphaltenes is 20%, which suppresses UV destruction by six times and best preserves the strength properties of PP.

Nanocellulose-stabilized bitumen emulsions as a base for preparation of nanocomposite asphalt binders

Pickering bitumen emulsions stabilized by 1 % aqueous dispersion of microfibrillated cellulose (MFC) were used to obtain micro- and nanocomposite asphalt binders. Initial bitumen emulsions are characterized by a yield stress for a bitumen content of up to 40 %, while higher bitumen amounts result in phase inversion with the formation of highly viscous inverse emulsions. Drying of emulsions leads to the production of nanocomposite bitumen binders containing from 0.6 % to 8.3 % of MFC. In this case, the MFC content of 1.5 % or more formed a microfibrillar network in the bitumen, which gives it gel-like properties and the yield stress, increasing its cohesive strength and resistance to rutting. The effect of addition of 5 % sodium dodecyl sulfate (SDS) on the properties of the bitumen emulsions and the resulting binders is considered. SDS increases the emulsifying ability of MFC, making it possible to obtain 70 % direct bitumen emulsions and reducing their effective viscosity together with the yield stress. However, the presence of SDS in the dried binders increases the aggregation of MFC, reducing the stiffness of the resulting microcomposite binders, their yield stress, and rutting resistance.

Infrared Spectral Classification of Natural Bitumens for Their Rheological and Thermophysical Characterization

Natural bitumens consist of many molecules whose chemical composition depends on the oilfield and determines the physicochemical properties of the bitumens as materials. Infrared (IR) spectroscopy is the fastest and least expensive method to assess the chemical structure of organic molecules, which makes it attractive in terms of rapid prediction of the properties of natural bitumens based on their composition evaluated in this way. In this work, IR spectra were measured for ten samples of natural bitumens significantly different in properties and origin. Based on the ratios of certain IR absorption bands, bitumens are proposed to be divided into paraffinic, aromatic, and resinous. In addition, the internal relationship between IR spectral characteristics of bitumens, such as polarity, paraffinicity, branchiness, and aromaticity, is shown. A study of phase transitions in bitumens by differential scanning calorimetry was carried out, and the use of a heat flow differential to find hidden points of bitumens' glass transitions is proposed. Furthermore, the dependences of the total melting enthalpy of crystallizable paraffinic compounds on the aromaticity and branchiness of bitumens are demonstrated. A detailed study of bitumens' rheology in a wide temperature range was carried out, and characteristic features of rheological behavior for different bitumen classes are revealed. Based on the viscous properties of bitumens, their glass transition points were found and compared with the calorimetric glass transition temperatures and nominal solid-liquid transition points obtained from temperature dependences of bitumens' storage and loss moduli. The dependences of viscosity, flow activation energy, and glass transition temperature of bitumens on their IR spectral characteristics are shown, which can be used to predict the rheological properties of bitumens.

Asphaltene-Stabilized Polyisobutylene Pressure-Sensitive Adhesives for Ultraviolet Protection and Surface Bonding

The usual way to protect indoor areas from solar UV radiation is to use UV-absorbing materials, which are applied as a thin film on the surface of the windowpane. Asphaltenes are useless wastes from crude oil refining that absorb UV radiation well, which gave the idea of their use in protective coatings. Pressure-sensitive adhesives based on polyisobutylene containing from 5 to 30 wt% of asphaltenes were obtained. Deterioration of the adhesive properties with the introduction of 5-20 wt% of asphaltenes was shown by adhesion tests, which can be associated with the plasticization of the polymer matrix. At the same time, the use of 30 wt% of asphaltenes leads to the polymer matrix reinforcement with the restoration of adhesive properties to the original level or even slightly higher. The rheological study of adhesives at 25 °C and 120 °C showed the structural network formation by asphaltenes at a content of 30 wt%, explaining the increase in adhesion performance. According to microscopy, asphaltenes are flat brown glass shards in a polymer matrix. They absorb electromagnetic radiation, predominantly in the UV range, while maintaining relative translucency in the visible range. This makes it possible to obtain thin films from the asphaltene-filled adhesive for bonding glass sheets to produce UV-blocked and tinted windowpanes.