Synthesis of chitosan-based flocculant by dielectric barrier discharge modification and its flocculation performance in wastewater treatment

As a typical type of organic flocculant, chitosan is limited by its poor water solubility and narrow pH range application. Grafting modification can improve chitosan's solubility and availability through linking macromolecular chains with other types of water-soluble groups or functional side groups. In this study, dielectric barrier discharge (DBD) was used to active the surface of chitosan, then activated chitosan was polymerized with acrylamide to synthesize a chitosan-based flocculant, chitosan-acrylamide (CS-AM). During the synthesis of CS-AM, the optimal conditions were determined as follows: discharge time of 5 min, discharge power of 60 W, total monomer mass concentration of 80 g L-1, polymerization time of 3 h, polymerization temperature of 70 °C, and m(CS) : m(AM) ratio of 1 : 3. The structure and morphological characteristics of CS-AM were investigated and analyzed by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), thermogravimetric (TG) analysis, scanning electron microscopy (SEM), X-ray diffraction (XRD) and N2 physical adsorption, respectively. The removal efficiency of kaolin suspension and CNTs suspension can reach up to 95.9% and 90.2% after flocculation of CS-AM. Furthermore, the zeta potential of the supernatant from the CS-AM treated kaolin suspension at different pH values was examined, and the flocculation mechanism of CS-AM was analyzed. This study provides new ideas for the preparation and development of modified chitosan and broadens its application in water treatment.

Optimizing the Conditions of Cationic Polyacrylamide Inverse Emulsion Synthesis Reaction to Obtain High–Molecular–Weight Polymers

Cationic polyacrylamide (CPAM) emulsifier is widely applied in the wastewater treatment industry, mining industry, paper industry, cosmetic chemistry, etc. However, optimization of input parameters in the synthesis of CPAM by using the traditional approach (i.e., changing one factor while leaving the others fixed at a particular set of conditions) would require a long time and a high cost of input materials. Onsite mass production of CPAM requires fast optimization of input parameters (i.e., stirring speed, reaction temperature and time, the amount of initiator, etc.) to minimize the production cost of specific–molecular–weight CPAM. Therefore, in this study, we synthesized CPAM using reverse emulsion copolymerization, and proposed response surface models for predicting the average molecular weight and reaction yield based on those input parameters. This study offers a time–saving tool for onsite mass production of specific–molecular–weight CPAM. Based on our response surface models, we obtained the optimal conditions for the synthesis of CPAM emulsions, which yielded medium–molecular–weight polymers and high conversion, with a reaction temperature of 60–62 °C, stirring speed of 2500–2600 rpm, and reaction time of 7 h. Quadratic models showed a good fit for predicting molecular weight (Adj.R2 = 0.9888, coefficient of variation = 2.08%) and reaction yield (Adj.R2 = 0.9982, coefficient of variation = 0.50%). The models suggested by our study would benefit the cost–minimization of CPAM mass production, where one could find optimal conditions for synthesizing different molecular weights of CPAM more quickly than via the traditional approach.

Research Progress on Typical Quaternary Ammonium Salt Polymers

Quaternary ammonium salt polymers, a kind of polyelectrolyte with a quaternary ammonium group, are widely used in traditional and emerging industries due to their good water-solubility, adjustable cationicity and molecular weight, high efficiency and nontoxicity. In this paper, firstly, the properties and several synthesis methods of typical quaternary ammonium salt monomers were introduced. Secondly, the research progress on the synthesis of polymers was summarized from the perspective of obtaining products with high molecular weight, narrow molecular weight distribution and high monomer conversion, and special functional polymers. Thirdly, the relationships between the structures and properties of the polymer were analyzed from the perspectives of molecular weight, charge density, structural stability, and microstructural regulation of the polymer chain unit. Fourthly, typical examples of quaternary ammonium salt polymers in the application fields of water treatment, daily chemicals, petroleum exploitation, papermaking, and textile printing and dyeing were listed. Finally, constructive suggestions were put forward on developing quaternary ammonium salt polymers with high molecular weights, strengthening the research on the relationships between the structures and their properties and pinpointing relevant application fields.

Research on a new cationic polyacrylamide (CPAM) with a cationic microblock structure and its enhanced effect on sludge condition and dewatering

Flocculation is one of the commonly used sludge conditioning methods in water supply plants, which can improve the sludge dewatering performance by reducing the specific resistance of sludge (SRF), decreasing the amount of sludge, and finally lowering the transportation cost and subsequent disposal cost of sludge. Therefore, it is particularly important to develop new and efficient flocculants. In this paper, the template copolymer of acryloxy trimethylammonium chloride (DAC) and acrylamide (AM) was successfully synthesized by microwave-template copolymerization (MV-TP) using sodium polyacrylate (NaPAA) as template. The template copolymer was analyzed by infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), nuclear magnetic resonance hydrogen spectroscopy (¹H NMR), and scanning electron microscopy (SEM). It was found that this template copolymer had obvious cationic microblock structure. In addition, the test results of association constant (K_M) and polymerization kinetics showed that the MW-TP was assigned to free radical initiated polymerization and the polymerization mechanism was I Zip-up (ZIP). It confirmed the formation of cation fragment structure again. Due to its dense positive charges in this new cationic microblock structure, it greatly improved the functions of electric neutralization, electrical patching, and adsorption bridging. The cationic fragment structure in the template copolymer could help to generate large and dense floc structure and form stable drainage channels. Under external pressure, these large and compact floc structures had greater compressive resistance, which avoided deformation and blockage of drainage channels and voids. It was beneficial to reduce SRF and evidently enhanced sludge dewatering performance.

Modification of microcrystalline cellulose with acrylamide under microwave irradiation and its application as flocculant

Grafting polyacrylamide (PAM) chains onto microparticles may combine the advantages of the flocculation property of the former and the fast sedimentation of the later to realize better flocculation performance. In this work, inexpensive microcrystalline cellulose (MCC) microparticles, and monomer of acrylamide (AM) were mixed, and then irradiated under microwave. The obtained material was characterized by Fourier transform infrared spectroscopy and X-ray diffraction, and the results demonstrated successful modification of MCC with AM on the particle surface. The modification procedure has been carefully investigated to obtain an optimum preparation condition. Kaolin suspension was selected as a model to evaluate the flocculation properties of the obtained AM-MCC. Our results indicate that the AM-MCC with the highest grafting ratio of 95.5% exhibits the best flocculation performance, which is even better than that of PAM, and the turbidity can be decreased to 1.4% of the naked kaolin suspension within 2.5 min. Therefore, this work provides a low cost strategy to prepare biodegradable AM-MCC, which may have promising potential application in the water treatment and other fields.