Developing a New Generation of Antimicrobial and Bioactive Dental Resins

Mechanical and Antimicrobial Properties of Boron Nitride/Methacrylic Acid Quaternary Ammonium Composites Reinforced Dental Flowable Resins

Dental resin composites (DRCs) are commonly used to restore teeth affected by dental caries or defects. These materials must possess excellent properties to withstand the complex oral environment. The objective of this study was to prepare and characterize Boron nitride nanosheets (BNN)/ dimethyl amino hexadecyl methacrylate (DMAHDM) composites (BNN/DMA), and to evaluate them as functional fillers to enhance the mechanical and antimicrobial properties of dental resins. The BNN/DMA composites were successfully prepared under the theoretical guidance of molecular dynamics (MD), and then the physicochemical and morphological characterization of the BNN/DMA composites were carried out by using various test methods, such as FT-IR, XRD, UV-vis spectroscopy, SEM, TEM, and AFM. It was doped into the dental flowable resin in a certain proportion, and the results showed that the flexural strength (FS), elastic modulus (EM), compressive strength (CS), and microhardness (MH) of the modified resin composites were increased by 53.29, 47.8, 97.59, and 37.1%, respectively, with the addition of 0.8 wt % of BNN/DMA composite fillers. It has a good inhibition effect on Streptococcus mutans, with an inhibition rate as high as 90.43%. Furthermore, this effect persists even after one month of aging. In conclusion, the modification of flowable resins with low-concentration BNN/DMA composites favorably integrates the mechanical properties and long-term antimicrobial activity of dental resins. At the same time, they have good biocompatibility and do not affect the aesthetics. The BNN/DMA composite modified flowable resin has the potential to become a new type of antimicrobial dental restorative material.

Novel antibacterial titanium implant healing abutment with dimethylaminohexadecyl methacrylate to combat implant-related infections

OBJECTIVE

Implant-related infections from the adhesion and proliferation of dental plaque are a major challenge for dental implants. The objectives of this study were to: (1) develop novel antibacterial titanium (Ti) healing abutment; (2) investigate the inhibition of implant infection-related pathogenic bacteria and saliva-derived biofilm, and evaluate the biocompatibility of the new material for the first time.

METHODS

Dimethylaminohexadecyl methacrylate (DMAHDM) and hydroxyapatite (HAP) were polymerized via polydopamine (PDA) on Ti. Staphylococcus aureus (S. aureus), Streptococcus sanguinis (S. sanguinis) and human saliva-derived biofilms were tested. After 4 weeks of DMAHDM release, the antibacterial efficacy of the DMAHDM remaining on Ti surface and the DMADHM in medium was tested. Biocompatibility was determined using human gingival fibroblasts (HGFs) and periodontal ligament stem cells (PDLSCs).

RESULTS

The DMAHDM-loaded coating filled into the nano-voids in Ti surfaces. The modified Ti showed potent antibacterial activity, reducing the CFU of S. aureus, S. sanguinis and saliva-derived biofilms by 8, 7 and 4 log, respectively (P < 0.05). After 4 weeks of release, the modified Ti was still able to reduce S. aureus and S. sanguinis biofilm CFU by 1-3 log (P < 0.05). This provided strong antibacterial function for more than 4 weeks, which were the high-risk period for implant infections. The new material showed excellent biocompatibility when compared to control (P > 0.05).

CONCLUSION

Novel DMAHDM-loaded Ti healing abutment had strong antibacterial effects, reducing biofilm CFUs by orders of magnitude, and lasting for over four weeks to cover the high-risk period for implant infections. The novel antibacterial Ti is promising to combat implant-related infections in dental, craniofacial and orthopedic applications.

Antimicrobial dental composites with K18-methyl methacrylate and K18-filler

OBJECTIVE

To determine the effects of using K18-methyl methacrylate (K18-MMA) and K18-Filler on composite cure, esthetic, mechanical, polymerization shrinkage, and antimicrobial properties.

METHODS

K18-MMA (0-20% w/w) was used to replace TEGDMA in a 70:30 Bis-GMA:TEGDMA composite filled to 70% w/w with barium glass or K18-Filler. Composite degree of cure (Rockwell15T hardness and near Infrared FTIR), hydrophilicity (contact angle measurements), translucency (transparency parameter measurements, TP), mechanical (3-point bend test), polymerization shrinkage (volumetric shrinkage and shrinkage stress), and antimicrobial properties (colony counting assay) against Streptococcus mutans, Streptococcus sanguinis, and Candida albicans were determined.

RESULTS

All experimental groups had comparable degrees of cure (near Infrared FTIR and Rockwell15T Hardness), TP, moduli, polymerization volumetric shrinkages and shrinkage stresses to those of controls (Bonferroni corrected p > 0.0018). Only one group (15% K18-MMA+K18-Filler) had significantly different (lower) contact angles as compared to that of controls (Bonferroni corrected p < 0.0018). Most of the K18-Filler-containing composites had significantly lower ultimate transverse strengths (UTS) than controls (Bonferroni corrected p < 0.0018). Controls had significantly greater S mutans colony counts than 15% and 20% w/w K18-MMA+K18-Filler groups, and greater S sanguinis and C albicans colony counts than K18-containing groups. Of the composites with that provided significant antimicrobial properties against S. mutans, S. sanguinis, and C. albicans, only the 20% K18-MMA+K18-Filler group had significantly lower UTS than controls.

SIGNIFICANCE

Composites with K18-MMA and K18-Filler with comparable physical properties to control composites and significant antimicrobial properties have been developed. K18-MMA and K18-Filler seem to be suitable for incorporation into commercial dental resins.

Prevalence of Dental Caries in Schoolchildren from the Galapagos Islands: ESSO-Gal Cohort Report

Objective

Dental caries remains a prevalent disease worldwide. Several epidemiological studies have shown that it affects the oral health of the pediatric population, and the Galapagos population in Ecuador is no exception. The aim of this study was to determine the prevalence of dental caries and its association, based on baseline information from the Galapagos Oral Health Study (ESSO-Gal), in children of the Galapagos Islands, Ecuador.

Methods

A cross-sectional study was conducted involving 804 children aged 2-11 years. The prevalence of dental caries was assessed using the International Caries Detection and Assessment System (ICDAS II) criteria, while the presence of dental biofilm was assessed using the Silness-Löe index. Descriptive statistics, including frequency analysis and measures of central tendency and dispersion, were performed. Inferential statistical analyses were conducted to identify associations between variables. Statistical analyses were performed using the SPSS version 25.0 statistical program.

Results

The caries prevalence rates based on ICDAS II codes 1-6, 1-2, and 3-6 were 98.01%, 96.9%, and 85%, respectively. A statistically significant difference was observed among the different islands regarding the cutoff point for ICDAS II codes 3-6 (p ≤ 0.001). Participants aged 6-11 years had the highest caries prevalence.

Conclusions

The results show a high prevalence of dental caries among children in the Galapagos Islands, which increases with age. Contrary to expectations, the study did not find a significant correlation between the severity of dental caries and the presence of dental biofilm.

Long-term application of silver nanoparticles in dental restoration materials: potential toxic injury to the CNS

Silver nanoparticles (AgNPs) have durable and remarkable antimicrobial effects on pathogenic microorganisms, such as bacteria and fungi, in dental plaques. As such, they are widely added to dental restoration materials, including composite resins, denture bases, adhesives, and implants, to solve the problems of denture stomatitis, peri-implant inflammation, and oral infection caused by the long-term use of these dental restoration materials. However, AgNPs can be absorbed into the blood circulatory system through the nasal/oral mucosa, lungs, gastrointestinal tract, skin, and other pathways and then distributed into the lungs, kidneys, liver, spleen, and testes, thereby causing toxic injury to these tissues and organs. It can even be transported across the blood-brain barrier (BBB) and continuously accumulate in brain tissues, causing injury and dysfunction of neurons and glial cells; consequently, neurotoxicity occurs. Other nanomaterials with antibacterial or remineralization properties are added to dental restoration materials with AgNPs. However, studies have yet to reveal the neurotoxicity caused by dental restoration materials containing AgNPs. In this review, we summarize the application of AgNPs in dental restoration materials, the mechanism of AgNPs in cytotoxicity and toxic injury to the BBB, and the related research on the accumulation of AgNPs to cause changes of neurotoxicity. We also discuss the mechanisms of neurotoxicity caused by AgNPs and the mode and rate of AgNPs released from dental restorative materials added with AgNPs to evaluate the probability of neurotoxic injury to the central nervous system (CNS), and then provide a theoretical basis for developing new composite dental restoration materials. Mechanism of neurotoxicity caused by AgNPs: AgNPs in the blood circulation enter the brain tissue after being transported across the BBB through transendothelial cell pathway and paracellular transport pathway, and continuously accumulate in brain tissue, causing damage and dysfunction of neurons and glial cells which ultimately leads to neurotoxicity. The uptake of AgNPs by neurons, astrocytes and microglia causes damage to these cells. AgNPs with non-neurotoxic level often increases the secretion of a variety of cytokines, up-regulates the expression of metallothionein in glial cells, even up-regulates autophagy and inflammation response to protect neurons from the toxic damage of AgNPs. However, the protective effect of glial cells induced by AgNPs exposure to neurotoxic levels is insufficient, which leads to neuronal damage and dysfunction and even neuronal programmed cell death, eventually cause neurotoxicity.

Restorative Dental Resin Functionalized with Calcium Methacrylate with a Hydroxyapatite Remineralization Capacity

The ability of dental materials to induce the mineralization of enamel like hydroxyapatite (HA) is of great importance. In this article, a novel kind of dental restorative material characterized by a mineralization ability was fabricated by photopolymerization. Calcium methacrylate (CMA) was introduced into the classical bisphenol A-glycidyl methacrylate (Bis-GMA) and triethylene glycol dimethacrylate (TEGDMA) dental resin formulation. This functional dental resin (BTCM) was calcium-rich and can be prepared simply by one-step photopolymerization. The influence of CMA on the photopolymerization kinetics, the dental resin's mechanical properties, and its capacity to induce dynamic in situ HA mineralization were examined. Real-time FTIR, compression modulus, scanning electron microscopy, X-ray spectroscopy, MTT assay, and cell attachment test were carried out. The obtained data were analyzed for statistical significance using analysis of variance (ANOVA). Double bond conversion could be completed in less than 300 s, while the compression modulus of BTCM decreased with the increase in CMA content (30 wt%, 40 wt%, and 50 wt%). After being soaked in Ca(NO3)2 and Na2HPO4 solutions alternatively, dense HA crystals were found on the surface of the dental resin which contained CMA. The amount of HA increased with the increase in CMA content. The MTT results indicated that BTCM possesses good biocompatibility, while the cell adhesion and proliferation investigation demonstrated that L929 cells can adhere and proliferate well on the surface of BTM. Thus, our approach provides a straightforward, cost-effective, and environmentally friendly solution that has the potential for immediate clinical use.

Effectiveness of adhesive containing MDPB: A practice-based clinical trial

OBJECTIVES

This prospective practice-based trial assessed the longevity of composite restorations made with an adhesive containing an antibacterial monomer compared to a conventional adhesive.

METHODS

9 general practices in the Netherlands were provided with two composite resin adhesives, each for a period of 9 months. Adhesive P contained the quaternary ammonium salt MDPB, and Adhesive S was a control. Patient's age and caries risk, as well as tooth type/number, reason for restoration placement, used restorative material and adhesive, and restored surfaces were recorded. All interventions carried out on these teeth in the 6 years after restoration were extracted from the electronic patient records, along with their date, type, reason, and surfaces. Two dependent variables were defined: general failure, and failure due to secondary caries. All data handling and multiple Cox regression analysis were carried out in R 4.0.5.

RESULTS

11 dentists from 7 practices made 10,151 restorations over a period of two years in 5102 patients. 4591 restorations were made with adhesive P, whereas 5560 were made with adhesive S. The observation period was up to 6.29 years, median observation time was 3.74 years. Cox regression showed no significant difference between the two adhesive materials when corrected for age, tooth type and caries risk, for general failure nor failure due to caries.

SIGNIFICANCE

No difference in restoration survival could be shown between composite restorations made using an adhesive containing MDPB and control. Restorations made with the adhesive containing MDPB also did not fail more or less frequently due to secondary caries. This trial is registered on clinicaltrials.gov with identifier NCT05118100.

Anticariogenic Activity of Celastrol and Its Enhancement of Streptococcal Antagonism in Multispecies Biofilm

Dental caries is a chronic disease resulting from dysbiosis in the oral microbiome. Antagonism of commensal Streptococcus sanguinis and Streptococcus gordonii against cariogenic Streptococcus mutans is pivotal to keep the microecological balance. However, concerns are growing on antimicrobial agents in anticaries therapy, for broad spectrum antimicrobials may have a profound impact on the oral microbial community, especially on commensals. Here, we report celastrol, extracted from Traditional Chinese Medicine's Tripterygium wilfordii (TW) plant, as a promising anticaries candidate. Our results revealed that celastrol showed antibacterial and antibiofilm activity against cariogenic bacteria S. mutans while exhibiting low cytotoxicity. By using a multispecies biofilm formed by S. mutans UA159, S. sanguinis SK36, and S. gordonii DL1, we observed that even at relatively low concentrations, celastrol reduced S. mutans proportion and thereby inhibited lactic acid production as well as water-insoluble glucan formation. We found that celastrol thwarted S. mutans outgrowth through the activation of pyruvate oxidase (SpxB) and H2O2-dependent antagonism between commensal oral streptococci and S. mutans. Our data reveal new anticaries properties of celastrol that enhance oral streptococcal antagonism, which thwarts S. mutans outgrowth, indicating its potential to maintain oral microbial balance for prospective anticaries therapy.

Novel mechanically strong and antibacterial dimethacrylate copolymers based on quaternary ammonium urethane-dimethacrylate analogues

OBJECTIVES

This study assumed that the quaternary ammonium urethane-dimethacrylate derivative (QAUDMA-m, where m was 8, 10, 12, 14, 16, 18, and corresponded to the number of carbon atoms in the N-alkyl substituent) can be used to achieve copolymers with high mechanical performance and antibacterial activity.

METHODS

Photocured copolymers of bisphenol A glycerolate dimethacrylate (Bis-GMA) 40 wt%, QAUDMA-m 40 wt%, and triethylene glycol dimethacrylate (TEGDMA) 20 wt% (BG:QAm:TEG) were characterized by the degree of conversion (DC), flexural strength (FS), flexural modulus (E), hardness (HB), and antibacterial properties (the number of bacteria colonies adhered to copolymer surfaces and inhibition zone diameter (IZD)) against Staphylococcus aureus and Escherichia coli. Reference copolymers of Bis-GMA, urethane-dimethacrylate monomer (UDMA), and TEGDMA (BG:TEG and BG:UD:TEG) were also characterized.

RESULTS

The DC of BG:QAm:TEGs ranged from 0.59 to 0.68, HB from 83.84 to 153.91 MPa, FS from 50.81 to 74.47 MPa, and E from 1986.74 to 3716.68 MPa. The number of S. aureus and E. coli bacteria adhered to BG:QAm:TEG surfaces was from 0 (no bacteria observed) to 6.47 and 4.99 log(CFU/mL), respectively. IZD was from 10 and 5 mm (no inhibition zone) to 23 and 21 mm, respectively. Three copolymers: BG:QA8:TEG, BG:QA10:TEG, and BG:QA12:TEG had similar or better mechanical properties than the reference copolymers, but unlike them, they showed high antibacterial activity against both bacteria strains.

SIGNIFICANCE

The obtained copolymers can offer a good, mechanically efficient, bioactive alternative to BG:TEG and BG:UD:TEG copolymers. The use of such materials can help to make progress in dental health care.

Novel Dental Low-Shrinkage-Stress Composite with Antibacterial Dimethylaminododecyl Methacrylate Monomer

OBJECTIVES

Current dental resins exhibit polymerization shrinkage causing microleakage, which has the potential to cause recurrent caries. Our objectives were to create and characterize low-shrinkage-stress (LSS) composites with dimethylaminododecyl methacrylate (DMADDM) as an antibacterial agent to combat recurrent caries.

METHODS

Triethylene glycol divinylbenzyl ether and urethane dimethacrylate were used to reduce shrinkage stress. DMADDM was incorporated at different mass fractions (0%, 1.5%, 3%, and 5%). Flexural strength, elastic modulus, degree of conversion, polymerization stress, and antimicrobial activity were assessed.

RESULTS

The composite with 5% DMADDM demonstrated higher flexural strength than the commercial group (p < 0.05). The addition of DMADDM in BisGMA-TEGDMA resin and LSS resin achieved clinically acceptable degrees of conversion. However, LSS composites exhibited much lower polymerization shrinkage stress than BisGMA-TEGDMA composite groups (p < 0.05). The addition of 3% and 5% DMADDM showed a 6-log reduction in Streptococcus mutans (S. mutans) biofilm CFUs compared to commercial control (p < 0.001). Biofilm biomass and lactic acid were also substantially decreased via DMADDM (p < 0.05).

CONCLUSIONS

The novel LSS dental composite containing 3% DMADDM demonstrated potent antibacterial action against S. mutans biofilms and much lower polymerization shrinkage-stress, while maintaining excellent mechanical characteristics. The new composite is promising for dental applications to prevent secondary caries and increase restoration longevity.

Antibacterial Activity of a Bioactive Tooth-Coating Material Containing Surface Pre-Reacted Glass in a Complex Multispecies Subgingival Biofilm

Bioactive materials were developed with the ability to release fluoride and provide some antimicrobial potential, to be widely used in dentistry today. However, few scientific studies have evaluated the antimicrobial activity of bioactive surface pre-reacted glass (S-PRG) coatings (PRG Barrier Coat, Shofu, Kyoto, Japan) on periodontopathogenic biofilms. This study evaluated the antibacterial activity of S-PRG fillers on the microbial profile of multispecies subgingival biofilms. A Calgary Biofilm Device (CBD) was used to grow a 33-species biofilm related to periodontitis for 7 days. The S-PRG coating was applied on CBD pins from the test group and photo-activated (PRG Barrier Coat, Shofu), while the control group received no coating. Seven days after treatment, the total bacterial counts, metabolic activity, and microbial profile of the biofilms were observed using a colorimetric assay and DNA-DNA hybridization. Statistical analyses were applied; namely, the Mann-Whitney, Kruskal-Wallis, and Dunn's post hoc tests. The bacterial activity of the test group was reduced by 25.7% compared with that of the control group. A statistically significant reduction was observed for the counts of 15 species: A. naeslundii, A. odontolyticus, V. parvula, C. ochracea, C. sputigena, E. corrodens, C. gracilis, F. nucleatum polymorphum, F. nucleatum vincentii, F. periodonticum, P. intermedia, P. gingivalis, G. morbillorum, S. anginosus, and S. noxia (p ≤ 0.05). The bioactive coating containing S-PRG modified the composition of the subgingival biofilm in vitro, thereby decreasing colonization by pathogens.

Novel bioactive dental restorations to inhibit secondary caries in enamel and dentin under oral biofilms

OBJECTIVE

To provide the first review on cutting-edge research on the development of new bioactive restorations to inhibit secondary caries in enamel and dentin under biofilms. State-of-the-art bioactive and therapeutic materials design, structure-property relationships, performance and efficacies in oral biofilm models.

DATA, SOURCES AND STUDY SELECTION

Researches on development and assessment new secondary caries inhibition restorations via in vitro and in vivo biofilm-based secondary caries models were included. The search of articles was carried out in Web of Science, PubMed, Medline and Scopus.

CONCLUSIONS

Based on the found articles, novel bioactive materials are divided into different categories according to their remineralization and antibacterial biofunctions. In vitro and in vivo biofilm-based secondary caries models are effective way of evaluating the materials efficacies. However, new intelligent and pH-responsive materials were still urgent need. And the materials evaluation should be performed via more clinical relevant biofilm-based secondary caries models.

CLINICAL SIGNIFICANCE

Secondary caries is a primary reason for dental restoration failures. Biofilms produce acids, causing demineralization and secondary caries. To inhibit dental caries and improve the health and quality of life for millions of people, it is necessary to summarize the present state of technologies and new advances in dental biomaterials for preventing secondary caries and protecting tooth structures against oral biofilm attacks. In addition, suggestions for future studies are provided.

Antibacterial coatings on orthopedic implants

With the aging of population and the rapid improvement of public health and medical level in recent years, people have had an increasing demand for orthopedic implants. However, premature implant failure and postoperative complications frequently occur due to implant-related infections, which not only increase the social and economic burden, but also greatly affect the patient's quality of life, finally restraining the clinical use of orthopedic implants. Antibacterial coatings, as an effective strategy to solve the above problems, have been extensively studied and motivated the development of novel strategies to optimize the implant. In this paper, a variety of antibacterial coatings recently developed for orthopedic implants were briefly reviewed, with the focus on the synergistic multi-mechanism antibacterial coatings, multi-functional antibacterial coatings, and smart antibacterial coatings that are more potential for clinical use, thereby providing theoretical references for further fabrication of novel and high-performance coatings satisfying the complex clinical needs.

Effect of monodisperse mesoporous bioactive glass spheres (MBGs) on the mechanical properties and bioactivity of dental composites

Secondary caries is one of the main reasons for the failure of dental resin composites, and adding bioactive fillers such as bioactive glass and amorphous calcium phosphate to the resin composites has been proved to be an effective solution for this problem. In the present study, we investigated the effect of monodisperse mesoporous bioactive glass spheres (MBGs) we prepared on the mechanical properties and bioactivity of dental resins. The results revealed that compared with traditional bioactive glass (BG), MBGs fillers significantly enhanced the mechanical properties of the dental resin composites, whether they were added alone or as functional fillers together with nonporous silica particles. The dental resins filled with bimodal fillers (mass ratio of MBGs: nonporous silica = 10:50, total filler loading 60 wt%) exhibited the best mechanical performance. Their flexural strength was 37.66% higher than the samples with BG at the same filling proportion. Furthermore, the prepared MBGs possessed excellent monodispersity and sufficient apatite formation performance, and the biocompatibility of the composites were also improved by MBGs fillers. These suggest the potential use of the prepared MBGs as multifunctional fillers for the improvement of the performance of dental resins.

Engineered Peptides Enable Biomimetic Route for Collagen Intrafibrillar Mineralization

Overcoming the short lifespan of current dental adhesives remains a significant clinical need. Adhesives rely on formation of the hybrid layer to adhere to dentin and penetrate within collagen fibrils. However, the ability of adhesives to achieve complete enclosure of demineralized collagen fibrils is recognized as currently unattainable. We developed a peptide-based approach enabling collagen intrafibrillar mineralization and tested our hypothesis on a type-I collagen-based platform. Peptide design incorporated collagen-binding and remineralization-mediating properties using the domain structure conservation approach. The structural changes from representative members of different peptide clusters were generated for each functional domain. Common signatures associated with secondary structure features and the related changes in the functional domain were investigated by attenuated total reflectance Fourier-transform infrared (ATR-FTIR) and circular dichroism (CD) spectroscopy, respectively. Assembly and remineralization properties of the peptides on the collagen platforms were studied using atomic force microscopy (AFM). Mechanical properties of the collagen fibrils remineralized by the peptide assemblies was studied using PeakForce-Quantitative Nanomechanics (PF-QNM)-AFM. The engineered peptide was demonstrated to offer a promising route for collagen intrafibrillar remineralization. This approach offers a collagen platform to develop multifunctional strategies that combine different bioactive peptides, polymerizable peptide monomers, and adhesive formulations as steps towards improving the long-term prospects of composite resins.

Effect of Bioactive Filler Addition on the Mechanical and Biological Properties of Resin-Modified Glass Ionomer

The maintenance of affected dentin can promote the greater conservation of tooth structure. The development of materials that have properties capable of reducing the demineralizing potential and/or even helping in dental remineralization is important for conservative dentistry. This study aimed to evaluate, in vitro, the alkalizing potential, fluoride as well as calcium ion release ability, antimicrobial activity, and dentin remineralization properties of resin-modified glass ionomer cement (RMGIC) incorporated with a bioactive filler (niobium phosphate (NbG) and bioglass (45S5)). The study samples were grouped into RMGIC, NbG, and 45S5. The materials' alkalizing potential, ability to release calcium as well as fluoride ions, and antimicrobial properties concerning Streptococcus mutans UA159 biofilms were analyzed. The remineralization potential was evaluated using the Knoop microhardness test, which was performed at different depths. The alkalizing and fluoride release potential was higher for the 45S5 group (p < 0.001) over time. An increase in the microhardness of demineralized dentin was observed in the 45S5 and NbG groups (p < 0.001). No differences in biofilm formation were observed between the bioactive materials, although 45S5 exhibited lower biofilm acidogenicity at different time points (p < 0.001) and greater calcium ion release in the microbial environment. A resin-modified glass ionomer cement enriched with bioactive glasses, particularly 45S5, is a promising alternative for the treatment of demineralized dentin.

pH-activated antibiofilm strategies for controlling dental caries

Dental biofilms are highly assembled microbial communities surrounded by an extracellular matrix, which protects the resident microbes. The microbes, including commensal bacteria and opportunistic pathogens, coexist with each other to maintain relative balance under healthy conditions. However, under hostile conditions such as sugar intake and poor oral care, biofilms can generate excessive acids. Prolonged low pH in biofilm increases proportions of acidogenic and aciduric microbes, which breaks the ecological equilibrium and finally causes dental caries. Given the complexity of oral microenvironment, controlling the acidic biofilms using antimicrobials that are activated at low pH could be a desirable approach to control dental caries. Therefore, recent researches have focused on designing novel kinds of pH-activated strategies, including pH-responsive antimicrobial agents and pH-sensitive drug delivery systems. These agents exert antibacterial properties only under low pH conditions, so they are able to disrupt acidic biofilms without breaking the neutral microenvironment and biodiversity in the mouth. The mechanisms of low pH activation are mainly based on protonation and deprotonation reactions, acids labile linkages, and H⁺-triggered reactive oxygen species production. This review summarized pH-activated antibiofilm strategies to control dental caries, concentrating on their effect, mechanisms of action, and biocompatibility, as well as the limitation of current research and the prospects for future study.

Orthodontic resins loaded with niobium silicate particles: Impact of filler concentration on the physicochemical and biological properties

OBJECTIVES

White spot lesions (WSL) are prevalent in patients using orthodontic appliances. The presence of ion-releasing compounds in the tooth-appliance interface may limit enamel demineralization to control WSL incidence. Thus, this study aims to evaluate the mineral formation on SiNb-containing experimental orthodontic resins and the influence of these fillers on the physicochemical and biological properties of developed materials.

MATERIALS AND METHODS

The SiNb particles were synthesized via the sol-gel route and characterized by their molecular structure and morphology. Photopolymerizable orthodontic resins were produced with a 75 wt% Bis-GMA/25 wt% TEGDMA and 10 wt%, 20 wt%, or 30 wt% addition of SiNb. A control group was formulated without SiNb. These resins were tested for their degree of conversion, softening in solvent, cytotoxicity in fibroblasts, flexural strength, shear bond strength (SBS), and mineral deposition.

RESULTS

The addition of 10 wt% of SiNb did not impair the conversion of monomers, cytotoxicity, and flexural strength. All groups with SiNb addition presented similar softening in solvent. The presence of these particles did not affect the bond strength between metallic brackets and enamel, with SBS values ranging from 16.41 to 18.66 MPa. The mineral deposition was observed for all groups.

CONCLUSION

The use of niobium silicate as filler particles in resins may be a strategy for the adhesion of orthodontic appliances. The 10 wt% SiNb concentration resulted in a material with suitable physicochemical and biological properties while maintaining the bond strength to tooth enamel and promoting mineral deposition.

Novel dental resin infiltrant containing smart monomer dodecylmethylaminoethyl methacrylate

Objectives

White spot lesions (WSLs) are prevalent and often lead to aesthetic problems and progressive caries. The objectives of this study were to: (1) develop a novel resin infiltrant containing smart monomer dodecylmethylaminoethyl methacrylate (DMAEM) to inhibit WSLs, and (2) investigate the effects of DMAEM incorporation on cytotoxicity, mechanical properties, biofilm-inhibition and protection of enamel hardness for the first time.

Methods

DMAEM was synthesized using 1-bromododecane, 2-methylamino ethanol and methylmethacrylate. DMAEM with mass fractions of 0%, 1.25%, 2.5% and 5% were incorporated into a resin infiltant containing BisGMA and TEGDMA. Cytotoxicity, mechanical properties and antibacterial effects were tested. After resin infiltration, bovine enamel was demineralized with saliva biofilm acids, and enamel hardness was measured.

Result

DMAEM infiltration did not increase the cytotoxicity or compromise the physical properties when DMAEM mass fraction was below 5% (p > 0.05). Biofilm metabolic activity was reduced by 90%, and biofilm lactic acid production was reduced by 92%, via DMAEM (p < 0.05). Mutans streptococci biofilm CFU was reduced by 3 logs (p < 0.05). When demineralized in acid and then under biofilms, the infiltrant + 5% DMAEM group produced an enamel hardness (mean ± sd; n = 6) of 2.90 ± 0.06 GPa, much higher than 0.85 ± 0.12 GPa of the infiltrant + 0% DMAEM group (p < 0.05).

Significance

A novel resin infiltrant with excellent mechanical properties, biocompability, strong antibacterial activity and anti-demineralization effect was developed using DMAEM for the first time. The DMAEM resin infiltrant is promising for inhibiting WSLs, arresting early caries, and protecting enamel hardness.

A novel dental infiltration resin based on isosorbide-derived dimethacrylate with high biocompatibility, hydrolysis resistance, and antibacterial effect

Objectives: The available infiltration resin has raised biosafety and treatment stability concerns because of the cytotoxicity of the main component, TEGDMA, and its susceptibility to hydrolysis in the oral environment. This study aimed to develop a TEGDMA-free infiltration resin to overcome these drawbacks. Methods: Using the synthetic bioderived monomer bis(methacrylate) isosorbide (IBM) and the zwitterionic compound 2-methacryloyloxyethyl phosphorylcholine (MPC), a novel infiltrant IBMA was developed and preferentially selected. We investigated the performance of the IBMA resin regarding cytotoxicity, antibiofilm adhesion, and hydrolysis resistance and further verified its ability to restore the demineralized enamel and stability of the infiltrated area under artificial aging conditions. Results: Compared with the commercial TEGDMA-based infiltration resin ICON, IBMA not only demonstrated similar enamel morphologic and esthetic restorative effects in chalky lesions but also exhibited favorable cell viability, durable Streptococcus mutans UA159 biofilm-repellent performance, and higher enamel microhardness (204.0 ± 5.12 HV) of the infiltrated enamel. Specifically, because of the high crosslink density [(47.77 ± 5.76) ×103 mol/mm3] and low water sorption [12.79 ± 2.56 µg/mm3] of the polymer network, the IBMA resin was more resistant to hydrolysis than ICON, which prevents the disruption of the infiltrant's micropore-blocking effect after aging. Enamel lesions treated with IBMA demonstrated good color stability after the tea-staining challenge, which was significantly better than that in the ICON group. Conclusion: Based on these findings, the IBMA resin exhibits favorable cell viability, hydrolysis resistance, and biofilm-repellent properties, which alleviates the defects of traditional TEGDMA systems. Therefore, it is a better alternative for microinvasive treatment involving early caries and enamel whitish discoloration.

Alkyl trimethyl ammonium bromide for the formulation of antibacterial orthodontic resins

OBJECTIVES

This study aimed at formulating antibacterial orthodontic resins containing alkyl trimethyl ammonium bromide (ATAB) and evaluating their physicochemical and biological properties.

MATERIALS AND METHODS

The chemical composition and microstructure of ATAB was characterized through FTIR and SEM, respectively. Experimental orthodontic BisGMA/TEGDMA-based resins were formulated, and the ATAB filler was incorporated at 1wt%, 5wt%, and 10wt%, along with colloidal silica (5wt%). The degree of conversion, softening in solvent, and flexural strength of the experimental resins were analyzed. Biological properties were also assessed through cytotoxicity and antibacterial analyses.

RESULTS

The incorporation of ATAB, due to the presence of ⎯N⁺(CH₃)₃ alkyl groups, had no adverse effect on the degree of conversion of the resins (p > 0.05). The %ΔKHN values at 5wt% and 10wt% were comparable to those of the control group, while the flexural strength was reduced at all concentrations of ATAB. The viability of the gingival fibroblast was reduced with the addition of ATAB (p < 0.05). The viability of biofilm and planktonic bacteria was reduced when ATAB was incorporated at 5wt% and 10wt%.

CONCLUSIONS

The addition of ATAB at 5wt% resulted suitable for the formulation of orthodontic resins with the ability to control the biofilm formation and planktonic activity of S.mutans, without jeopardizing some specific physicochemical properties.

CLINICAL RELEVANCE

White spot lesions in orthodontic patients may be controlled by preventive treatments. Non-patient-dependent strategies, such as the use of orthodontic resins containing ATAB, may avoid accumulation of bacteria, especially in those areas surrounding orthodontic appliances.

Effect of strontium-doped bioactive glass-ceramic containing toothpaste on prevention of artificial dentine caries formation: an in vitro study

Backgroud

Root caries in aging population was prevalent worldwide. Due to the absence of enamel and specific structure of dentine, bacteria are able to penetrate further into dentine at an earlier stage of lesion development. The aim of this study was to investigate the effect of adding of a strontium-doped bioactive glass-ceramic (HX-BGC) to a fluoride-free toothpaste on prevention of formation of artificial dentine caries.

Methods

Thirty-six human tooth specimens were allocated to three groups (n = 12 per group). Group 1 treated with slurry containing a fluoride-free toothpaste and 5% HX-BGC, Group 2 was treated with fluoride-free toothpaste slurry, and Group 3 received deionized water as a negative control. The specimens were subjected to four cycles (15 h demineralization and 8 h remineralization for one cycle) of biochemical cycling. A mixed suspension of five bacteria species (Streptococcus mutans, Streptococcus sobrinus, Lactobacillus acidophilus, Lactobacillus rhamnosus, and Actinomyces naeslundii) were prepared in brain heart infusion broth with 5% sucrose and used as acidic challenge in biochemical cycling. Subsequently, surface morphology of the dentine lesion was assessed by scanning electron microscopy, while the lesion depths and mineral loss were assessed by micro-computed tomography.

Results

The mean lesion depths in dentine in Groups 1 to 3 were 87.79 ± 16.99 μm, 101.06 ± 10.04 μm and 113.60 ± 16.36 μm, respectively (p = 0.002). The mean amounts of mineral loss in Groups 1 to 3 were 0.82 ± 0.10 g/cm³, 0.89 ± 0.09 g/cm³ and 0.96 ± 0.11 g/cm³, respectively (p = 0.016). No obvious differences in the surface morphology were seen among the groups.

Conclusion

Addition of strontium-doped bioactive glass-ceramic to fluoride-free toothpaste has potential to reduce formation of dentine lesions.

Effects of the crosslinking of chitosan/DCPA particles in the antimicrobial and mechanical properties of dental restorative composites

The development of restorative materials containing antibacterial agents is an alternative to reduce the progression of caries lesions.

OBJECTIVE

to compare the influence of the degree of crosslinking of chitosan particles loaded with dibasic calcium phosphate (DCPA) on the mechanical properties, degree of conversion (DC), and antimicrobial properties of experimental composites.

METHODS

Chitosan/DCPA particles were synthesized by the electrospraying, crosslinked by 0, 8, or 16 h in glutaraldehyde, and characterized by zeta potential and minimum inhibitory concentration (MIC) against S. mutans. Experimental resin composites of Bis-GMA and TEGDMA and 59.5% of barium glass were synthesized, chitosan/DCPA particles were added at 0 or 0.5 wt% with the different crosslinking time. The materials were subject to DC analysis, three-point bending test at 24 h and 7 days, and antimicrobial assays. Data were submitted to one-way ANOVA and Tukey test (α = 0.05).

RESULTS

The particles with longer crosslinking time presented higher zeta potential and MIC, and the composite containing these particles showed significantly higher biofilm inhibition than the control group. The other two groups were similar to each other and the control. The composite containing particles with 88 h crosslinking time showed the lowest flexural strength at 7 days in water, and materials with non-crosslinked particles and longer crosslinking time presented flexural strength similar to control. The flexural modulus and DC showed no statistical difference among groups.

SIGNIFICANCE

composite resin containing 0.5% chitosan/DCPA particles crosslinked by 16 h showed a reduction of biofilm formation without affecting the mechanical properties in relation to the control.

Physico-mechanical properties, antimicrobial activities, and anti-biofilm potencies of orthodontic adhesive containing cerium oxide nanoparticles against Streptococcus mutans

Introduction: White spot lesions around orthodontic brackets may lead to the formation of dental caries during and following fixed orthodontic treatment.

Aim: This study aimed to evaluate the physico-mechanical properties and antimicrobial potencies of orthodontic adhesive doped with cerium oxide nanoparticles (CeO2-NPs) against Streptococcus mutans.

Materials and methods: After synthesis and conformation of CeO2-NPs by transmission electron microscope (TEM), shear bond strength (SBS) and adhesive remnant index (ARI) of modified orthodontic adhesive containing different concentrations of CeO2-NPs (0, 1, 2, 5, and 10 wt%) were measured. The antimicrobial effects of modified orthodontic adhesive were evaluated by disk agar diffusion method and biofilm formation inhibition assay.

Results: The pseudo-spherical shapes of CeO2-NPs were observed in TEM micrographs. The physico-mechanical finding showed that 5 wt% CeO2-NPs showed the highest concentration of CeO2-NPs and SBS value (18.21±9.06 MPa, p&lt;0.05) simultaneously with no significant differences in ARI compared with the control group (p&gt;0.05). There was a significant reduction in cell viability of S. mutans with increasing CeO2-NPs concentration. The 3.1 Log10 and 4.6 Log10 reductions were observed in the count of treated S. mutans with 5 and 10 wt% CeO2-NPs, respectively (p&lt;0.05).

Conclusions: Overall, an orthodontic adhesive containing 5 wt% CeO2-NPs had antimicrobial properties against S. mutans without adverse effects on SBS and ARI.

Exploring the use of a Ruthenium complex incorporated into a methacrylate-based dental material for antimicrobial photodynamic therapy

OBJECTIVES

To evaluate the effects of a blue light photosensitizer (PS), Ruthenium II complex (Ru), on the chemical, physical, mechanical, and antimicrobial properties of experimental dental resin blends.

METHODS

The experimental resin (BisEMA, TEEGDMA, HPMA, ethanol, and photoinitiator) was loaded with Ru at 0.00%, 0.07%, 0.14%, 0.28%, 0.56%, 1.12%, 1.2%, 1.5%, 2%, 3%, 4%, 5%, 6%, 7%, 8%, 9%, or 10% w/w. Samples were evaluated for the degree of conversion (DC) after 30 and 60 s curing-time (n = 6). Selected formulations (0.00%, 0.28%, 0.56%, 1.12%) were further tested for shear bond strength (SBS) (n = 15); flexural strength (FS) (n = 12); and antimicrobial properties (CFUs), in dark and light conditions. These latter tests were performed on specimens stored for 24-h or 2-month in 37°C water. Water sorption (WS) and solubility (SL) tests were also performed (n = 12). Data were analyzed either by a one- or two-factor general linear model (α = 0.05).

RESULTS

Overall, Ru concentration above 1.2% resulted in reduced DC. In SBS results, only the 1.12%Ru resin blend samples had statistically lower values compared to the 0.00%Ru resin blend at 24-h storage (p = 0.004). In addition, no differences in SBS were detected among the experimental groups after 2-month storage in water. Meanwhile, FS increased for all experimental groups under similar aging conditions (p < 0.001). Antimicrobial properties were improved upon inclusion of Ru and application of light (p < 0.001 for both) at 24-h and 2-month storage. Lastly, no detectable changes in WS or SL were observed for the Ru-added resins compared to the 0.00%Ru resin blend. However, the 0.28% Ru blend presented significantly higher WS compared to the 0.56% Ru blend (p = 0.007).

CONCLUSIONS

Stable SBS, improved FS, and sustained antimicrobial properties after aging gives significant credence to our approach of adding the Ruthenium II complex into dental adhesive resin blends intended for an aPDT approach.

Multifunctional Coatings of Titanium Implants Toward Promoting Osseointegration and Preventing Infection: Recent Developments

Titanium and its alloys are dominant material for orthopedic/dental implants due to their stable chemical properties and good biocompatibility. However, aseptic loosening and peri-implant infection remain problems that may lead to implant removal eventually. The ideal orthopedic implant should possess both osteogenic and antibacterial properties and do proper assistance to in situ inflammatory cells for anti-microbe and tissue repair. Recent advances in surface modification have provided various strategies to procure the harmonious relationship between implant and its microenvironment. In this review, we provide an overview of the latest strategies to endow titanium implants with bio-function and anti-infection properties. We state the methods they use to preparing these efficient surfaces and offer further insight into the interaction between these devices and the local biological environment. Finally, we discuss the unmet needs and current challenges in the development of ideal materials for bone implantation.

Minimally Invasive Therapies for the Management of Dental Caries—A Literature Review

In recent years, due to a better understanding of the caries pathology and advances in dental materials, the utilization of non-invasive and minimally invasive techniques that delay/obviate the need for traditional restorations has started gaining momentum. This literature review focuses on some of these approaches, including fluoride varnish, silver diamine fluoride, resin sealants, resin infiltration, chemomechanical caries removal and atraumatic restorative treatment, in the context of their chemistries, indications for use, clinical efficacy, factors determining efficacy and limitations. Additionally, we discuss strategies currently being explored to enhance the antimicrobial properties of these treatment modalities to expand the scope of their application.

The Antibacterial and Remineralization Effect of Silver-Containing Mesoporous Bioactive Glass Sealing and Er-YAG Laser on Dentinal Tubules Treated in a Streptococcus mutans Cultivated Environment

The aim of this study was to evaluate the remineralization and antibacterial effect of silver-containing mesoporous bioactive glass (MBG-Ag) sealing combined with Er:YAG laser irradiation on human demineralized dentin specimens in a Streptococcus mutans cultivated environment. A total of 48 human dentin specimens were randomly divided into four groups. The characteristics of MBG-Ag and the occlusion efficiency of the dentinal tubules were analyzed using X-ray diffraction patterns, Fourier-transform infrared spectroscopy, scanning electron microscope images and energy dispersive X-ray spectroscopy. Moreover, the antibacterial activity against Streptococcus mutans was evaluated by colony formation assay. The results showed that the dentin specimens with Er:YAG laser irradiation can form a melted occlusion with a size of 3–4 µm. MBG-Ag promoted the deposition of numerous crystal particles on the dentinal surface, reaching the deepest penetration depth of 70 μm. The results suggested that both MBG-Ag and laser have the ability to enhance the remineralization and precipitation of hydroxyapatite crystals. While the results showed that MBG-Ag sealing combined with the thermomechanical subablation mode of Er:YAG laser irradiation-induced dense crystalline deposition, reaching a penetration depth of more than 300 µm, silver nanoparticles without good absorption of the Er:YAG laser resulted in a heterogeneous radiated surface. Er:YAG laser irradiation with a low energy and pulse rate cannot completely inhibit the growth of S. mutans, but MBG-Ag sealing reached the bactericidal concentration. It was concluded that the simultaneous application of MBG-Ag sealing and Er:YAG laser treatment can prevent the drawbacks of their independent uses, resulting in a superior form of treatment for dentin hypersensitivity.

Intelligent pH-responsive dental sealants to prevent long-term microleakage

OBJECTIVES

Microleakage is a determinant factor of failures in sealant application. In this study, DMAEM (dodecylmethylaminoethyl methacrylate), a pH-responsive antibacterial agent, was incorporated into resin-based sealant for the first time. The objectives of this study were to: (1) investigate the long-term performance of DMAEM-modified sealants against oral microbial-aging; and (2) investigate the long-term preventive effect of DMAEM-modified sealants on microleakage.

METHODS

Depth-of-cure and cytotoxicity of DMAEM-modified sealants were measured. Then, an aging model using biofilm derived from the saliva of high caries experience children was conducted. After aging, microhardness and surface roughness were measured. Biofilm activity, lactic acid production and exopolysaccharide (EPS) production were measured. 16S rRNA gene sequencing were also performed. The effects of DMAEM on microleakage were tested using an in vitro microleakage assessment.

RESULTS

The addition of DMAEM with a mass fraction of 2.5-10% did not affect depth-of-cure values and cytotoxicity of sealants. Adding 2.5-10% DMAEM did not affect the surface roughness and microhardness after aging. Compared to control, adding 2.5-10% DMAEM reduced biofilm metabolic activity by more than 80%. The lactic acid production and EPS production were reduced by 50% in DMAEM groups. DMAEM-modified sealants maintained the microbial diversity of biofilm after aging, they also inhibited the growth of lactobacillus. The 5% and 10% DMAEM groups exhibited a significant reduction in microleakage compared to control.

SIGNIFICANCE

The long-term antibacterial activities against oral microbial-aging and the long-term microecosystem-regulating capabilities enabled DMAEM-modified sealant to prevent microleakage in sealant application and thus prevent dental caries.

Effect of Antibacterial Root Canal Sealer on Persistent Apical Periodontitis

The infection of Enterococcus faecalis and its interacting microorganisms in the root canal could cause persistent apical periodontitis (AP). Antibacterial root canal sealer has favorable prospects to inhibit biofilms. The purpose of this study was to investigated the antibacterial effect of root canal sealer containing dimethylaminododecyl methacrylate (DMADDM) on persistent AP in beagle dogs for the first time. Persistent AP was established by a two-step infection with Enterococcus faecalis and multi-bacteria (Enterococcus faecalis, Lactobacillus acidophilus, Actinomycesnaeslundii, Streptococcus gordonii). Root canal sealer containing DMADDM (0%, 1.25%, 2.5%) was used to complete root canal filling. The volume of lesions and inflammatory grade in the apical area were evaluated by cone beam computer tomography (CBCT) and hematoxylin-eosin staining. Both Enterococcus-faecalis- and multi-bacteria-induced persistent AP caused severe apical destruction, and there were no significant differences in pathogenicity between them. DMADDM-modified sealer significantly reduced the volume of periapical lesion and inflammatory grade compared with the control group, among them, the therapeutic effect of the 2.5% group was better than the 1.25% group. In addition, E.faecalis-induced reinfection was more sensitive to the 2.5% group than multi-bacteria reinfection. This study shows that root canal sealer containing DMADDM had a remarkable therapeutic effect on persistent AP, especially on E. faecalis-induced reinfection.

Novel Bioactive Glass-Modified Hybrid Composite Resin: Mechanical Properties, Biocompatibility, and Antibacterial and Remineralizing Activity

Secondary caries seriously limits the lifetime of composite resin. However, integrating all desirable properties (i.e., mechanical, antibacterial, bioactivity, and biocompatibility) into one composite resin is still challenging. Herein, a novel bioactive glass (BAG)-modified hybrid composite resin has been successfully developed to simultaneously achieve excellent mechanical properties, good biocompatibility, and antibacterial and remineralizing capabilities. When the mass fractions of BAG particles were added from 8 to 23 wt %, the original mechanical properties of the composite resin, including flexural strength and compressive strength, were not obviously affected without compromising the degree of conversion. Although the BAG incorporation of mass fractions of 16 wt % to 23 wt % in composite resins reduced cell viability, the viability could be recovered to normal by adjusting the pH value. Moreover, the BAG-modified composite resins that were obtained showed good antibacterial effects against Streptococcus mutans and enhanced remineralizing activity on demineralized dentin surfaces with increasing incorporation of BAG particles. The possible mechanisms for antibacterial and remineralizing activity might be closely related to the release of bioactive ions (Ca²⁺, Si⁴⁺), suggesting that its antibacterial and biological properties can be controlled by modulating the amounts of bioactive ions. The capability to balance the mechanical properties, cytotoxicity, antibacterial activity, and bioactivity makes the BAG-modified composite resin a promising prospect for clinical application. Our findings provide insight into better design and intelligent fabrication of bioactive composite resins.

Novel dental implant modifications with two-staged double benefits for preventing infection and promoting osseointegration in vivo and in vitro

Peri-implantitis are a major problem causing implant failure these days. Accordingly, anti-infection during the early stage and subsequent promotion of osseointegration are two main key factors to solve this issue. Micro-arc oxidation (MAO) treatment is a way to form an oxidation film on the surface of metallic materials. The method shows good osteogenic properties but weak antibacterial effect. Therefore, we developed combined strategies to combat severe peri-implantitis, which included the use of a novel compound, PD, comprising dendrimers poly(amidoamine) (PAMAM) loading dimethylaminododecyl methacrylate (DMADDM) as well as MAO treatment. Here, we explored the chemical properties of the novel compound PD, and proved that this compound was successfully synthesized, with the loading efficiency and encapsulation efficiency of 23.91% and 31.42%, respectively. We further report the two-stage double benefits capability of PD + MAO: (1) in the first stage, PD + MAO could decrease the adherence and development of biofilms by releasing DMADDM in the highly infected first stage after implant surgery both in vitro and in vivo; (2) in the second stage, PD + MAO indicated mighty anti-infection and osteoconductive characteristics in a rat model of peri-implantitis in vivo. This study first reports the two-staged, double benefits of PD + MAO, and demonstrates its potential in clinical applications for inhibiting peri-implantitis, especially in patients with severe infection risk.

Recent Progress in Antimicrobial Strategies for Resin-Based Restoratives

Repairing tooth defects with dental resin composites is currently the most commonly used method due to their tooth-colored esthetics and photocuring properties. However, the higher than desirable failure rate and moderate service life are the biggest challenges the composites currently face. Secondary caries is one of the most common reasons leading to repair failure. Therefore, many attempts have been carried out on the development of a new generation of antimicrobial and therapeutic dental polymer composite materials to inhibit dental caries and prolong the lifespan of restorations. These new antimicrobial materials can inhibit the formation of biofilms, reduce acid production from bacteria and the occurrence of secondary caries. These results are encouraging and open the doors to future clinical studies on the therapeutic value of antimicrobial dental resin-based restoratives. However, antimicrobial resins still face challenges such as biocompatibility, drug resistance and uncontrolled release of antimicrobial agents. In the future, we should focus on the development of more efficient, durable and smart antimicrobial dental resins. This article focuses on the most recent 5 years of research, reviews the current antimicrobial strategies of composite resins, and introduces representative antimicrobial agents and their antimicrobial mechanisms.

Development of endodontic sealers containing antimicrobial-loaded polymer particles with long-term antibacterial effects

OBJECTIVE

The objective of this study is to prepare new dental resins with a long-lasting antimicrobial activity. Specifically, this study evaluates an approach for controlling infection in root canals using sealers containing polyhydroxyethyl methacrylate trimethylolpropane trimethacrylate (polyHEMA/TMPT) particles loaded with cetylpyridinium chloride (CPC). In addition, the physical properties of sealers containing CPC-loaded polyHEMA/TMPT particles (CLP) are determined.

METHODS

PolyHEMA/TMPT particles with 10 (10%-CLP) and 25wt.% CPC (25%-CLP) with different particle sizes were fabricated and incorporated in HEMA-based sealers. CPC-release profiles were evaluated over 14 days of immersion in water, followed by 14 days of storage and 14 days of water immersion. The antibacterial activity of these sealers against Enterococcus faecalis in dentinal tubules was assessed using a root-canal-infection model. Their sealing abilities were evaluated by fluid filtration and physical properties were tested according to the ISO 6876 standard. The long-term antibacterial activity of the cured sealer containing 25%-CLP (∼21μm particle diameter) was re-assessed after 1 year of storage.

RESULTS

After 28 days of immersion, 25%-CLP exhibited a higher and sustained CPC release unlike 10%-CLP. Residual bacteria in root dentinal tubules were eradicated by obturation with 25%-CLP-containing sealers. The incorporation of 25%-CLP (∼21μm) had no adverse effects on the sealing ability and physical properties of the sealer and resulted in long-term antibacterial activity.

SIGNIFICANCE

The incorporation of CPC-loaded particles in HEMA resins yielded endodontic sealers with long-term bactericidal activity against E. faecalis in root canals. These sealers can potentially be used to prevent recurrent apical periodontitis.

Development and characterization of self-etching adhesives doped with 45S5 and niobophosphate bioactive glasses: Physicochemical, mechanical, bioactivity and interface properties

OBJECTIVE

The aim of study was to develop and characterize experimental bioactive glasses (45S5 and niobophosphate bioactive glass (NbG)) and evaluate the effects of their addition in self-etching adhesive systems on physicochemical, mechanical, and bioactive properties, microtensile bond strength (μTBS), and nanoleakage (NL).

METHODS

Two-step self-etching adhesive systems containing 5, 10, and 20 wt.% of 45S5 and NbG bioactive glasses were developed. An experimental adhesive without microparticles and a commercial adhesive (Clearfil SE Bond) were used as control groups. The materials were evaluated for their degree of conversion (DC%), ultimate tensile strength (UTS), softening in solvent, radiopacity, sorption and solubility, alkalizing activity (pH), ionic release, and bioactivity. μTBS and NL were evaluated after 24 h and 1 year of storage. The data were subjected to analysis of variance and post-Holm-Sidak tests (α = 0.05).

RESULTS

The addition of the two bioactive glasses did not change the values of the degree of conversion, ultimate tensile strength, and softening in solvent. The adhesive system containing 20% NbG showed the highest radiopacity. The incorporation of 45S5 increased water sorption and solubility, raised the pH, and allowed the release of large amounts of calcium. After 28 days of immersion in simulated body fluid, the 45S5 adhesive precipitated hydroxyapatite and calcium carbonate (SEM/EDX, ATR/FTIR, and XDR). The addition of 45S5 and NbG to the adhesives improved the stability of the resin-dentin interface after 1 year.

SIGNIFICANCE

The incorporation of microparticles from 45S5 bioactive glass in self-etching adhesive systems is considered an excellent alternative for the development of a bioactive adhesive that improves the integrity of the hybrid layer on sound dentin.

Synthesis and antibacterial activity of polymer-antibiotic conjugates incorporated into a resin-based dental adhesive

This work reports on polymer-antibiotic conjugates (PACs) as additives to resin-based restorative dental materials as a new strategy to convey sustained antibacterial character to these materials. Such antibacterial performance is expected to improve their longevity in the oral cavity. Using the previously reported ciprofloxacin (Cip)-based PAC as a control, a penicillin V (PV)-based PAC was investigated. The monomer-antibiotic conjugate (MAC) containing a methacrylate monomer group and a PV moiety was prepared via nucleophilic substitution between 2-chloroethyl methacrylate (CEMA) and penicillin V potassium (PVK). The PV-based PAC was synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization of the MAC with hydroxyethyl methacrylate (HEMA), and further characterized by 1H NMR and gel permeation chromatography (GPC) analysis. Antibiotic resistance was investigated by passaging bacteria in low concentrations of the antibiotic for 19 days, followed by a 48 h challenge at higher concentrations. Our results suggest that the development of antibiotic resistance is unlikely. Zone of inhibition (ZOI) assays revealed no clearing zones around PV-containing resins indicating minimal antibiotic leakage from the material. Similarly, MTT assay demonstrated that the antibiotic-containing specimens did not release cytotoxic byproducts that may inhibit human gingival fibroblast growth. Counting of colony-forming units in an S. mutans biofilm model was used to assess bacterial survival at baseline and after subjecting the antibiotic-containing resin specimens to an enzymatic challenge for 30 days. Significantly reduced bacterial counts were observed as the biofilm aged from 24 to 72 h, and salivary enzymatic exposure did not reduce the antibacterial efficacy of the discs, suggesting that PV-resin will be effective in reducing the re-incidence of dental caries.

Dental Restorative Materials for Elderly Populations

The incidence of dental caries, especially root caries, has risen in elderly populations in recent years. Specialized restorative materials are needed due to the specific site of root caries and the age-related changes in general and oral health in the elderly. Unfortunately, the restorative materials commonly used clinically cannot fully meet the requirements in this population. Specifically, the antibacterial, adhesive, remineralization, mechanical, and anti-aging properties of the materials need to be significantly improved for dental caries in the elderly. This review mainly discusses the strengths and weaknesses of currently available materials, including amalgam, glass ionomer cement, and light-cured composite resin, for root caries. It also reviews the studies on novel anti-caries materials divided into three groups, antimicrobial, remineralization, and self-healing materials, and explores their potential in the clinical use for caries in the elderly. Therefore, specific restorative materials for caries in the elderly, especially for root caries, need to be further developed and applied in clinical practice.

Influence of Additive Firing on the Surface Characteristics, Streptococcus mutans Viability and Optical Properties of Zirconia

The purpose of this study was to observe whether the repetitive firing of dental zirconia caused changes in surface characteristics, S. mutans viability, and optical properties of zirconia. Dental zirconia blocks were sintered and randomly distributed into seven experimental groups: F0–F6. Except for F0, which only went through sintering, the additive firing was performed in order for F1–F6. Surface roughness, contact angle, S. mutans viability by fluorescence, and translucency parameter were measured. They were all highest after sintering (F0) and decreased after additive firings (F1–F6). The additive firing of zirconia after sintering decreased surface roughness, contact angle, S. mutans viability, and translucency. The number of firings after the first firing was not found to be critical in surface characteristics, S. mutans viability, and optical property. Changes in surface characteristics might have led to a decrease in S. mutans viability, while the change of translucency was not clinically significant. This implies that additive firing may prevent secondary caries under zirconia restorations, not compromising esthetic appearance.

Effect of a chlorhexidine-encapsulated nanotube modified pit-and-fissure sealant on oral biofilm

The purpose of this study was to characterize a chlorhexidine-encapsulated nanotube modified pit-and-fissure sealant for biofilm development prevention. HS (commercial control); HNT (HS+15wt%Halloysite^®-clay-nanotube); CHX10% (HS+15wt% HNT-encapsulated with chlorhexidine 10%); and CHX20% (HS+15wt% HNT-encapsulated with CHX20%) were tested. Degree-of-conversion (DC%), Knoop hardness (KHN), and viscosity were analyzed. The ability of the sealant to wet the fissures was evaluated. Specimens were tested for zones of inhibition of microbial growth. S. mutans biofilm was tested by measuring recovered viability. Data were statistically analyzed (p<0.05). DC% was significantly higher for the HNT-CHX groups. For KHN, CHX10% presented a lower mean value than the other groups. Adding HNT resulted in higher viscosity values. The biofilm on CHX10% and CHX20% sealants presented remarkable CFU/mL reduction in comparison to the HS. The experimental material was able to reduce the biofilm development in S. mutans biofilm without compromising the sealant properties.

The antibacterial effect and physical performance of pit and fissure sealants based on an antibacterial core-shell nanocomposite

The application of pit and fissure sealants is a well-established method to prevent and treat early childhood caries. Resin-based sealants with antibacterial properties provide additional benefits for caries prevention in a cariogenic oral environment. The objective of this study was to evaluate the effect of an antibacterial core-shell AgBr/cationic polymer nanocomposite (AgBr/BHPVP) on the properties of a resin-based pit and fissure sealant. A commercialized pit and fissure sealant without fluoride, Concise (3M, ESPE, USA), was used as the parent material and negative control. Experimental antibacterial sealants were formulated by the addition of AgBr/BHPVP nanoparticles at mass fractions of 0.5, 1.0, and 1.5 wt% to the parent material. A fluoride-releasing sealant, Clinpro (3M, ESPE), was used as the positive control. Bacterial colony-forming unit (CFU) counts, metabolic activity tests, field emission-scanning electron microscopy (FE-SEM), and confocal laser scanning microscopy (CLSM) observations were used to evaluate the antibacterial properties of AgBr/BHPVP-modified sealants against Streptococcus mutans before and after five months of aging. The Vickers microhardness, degree of conversion, and microleakage level of the sealants were also investigated. According to the results of CFU counts and metabolic tests, sealants containing AgBr/BHPVP showed better contact-killing bactericidal activity against S. mutans than the two commercial sealants, irrespective of aging conditions (both P < 0.05). The AgBr/BHPVP-modified sealants also showed a significant inhibitory effect on the planktonic S. mutans around the cured sealant surfaces. In addition, the Vickers microhardness, degree of conversion, and microleakage level of the parent material were not damaged by modification with AgBr/BHPVP (P > 0.05). AgBr/BHPVP-modified pit and fissure sealant with a dual bactericidal mechanism is a promising option for the prevention of pit and fissure caries.

Cirrhotic Liver of Liver Transplant Recipients Accumulate Silver and Co-Accumulate Copper

Silver-based materials are widely used in clinical medicine. Furthermore, the usage of silver containing materials and devices is widely recommended and clinically approved. The impact on human health of the increasing use of silver nanoparticles in medical devices remains understudied, even though Ag-containing dressings are known to release silver into the bloodstream. In this study, we detected a widespread and sometimes significant silver accumulation both in healthy and sick liver biopsies, levels being statistically higher in patients with various hepatic pathologies. 28 healthy and 44 cirrhotic liver samples were investigated. The median amount of 0.049 ppm Ag in livers was measured in cirrhotic livers while the median was 0.0016 ppm for healthy livers (a more than 30-fold difference). The mean tissue concentrations of essential metals, Fe and Zn in cirrhotic livers did not differ substantially from healthy livers, while Cu was positively correlated with Ag. The serum levels of gamma-glutamyl transpeptidase (GGTP) was also positively correlated with Ag in cirrhotic livers. The increased Ag accumulation in cirrhotic livers could be a side effect of wide application of silver in clinical settings. As recent studies indicated a significant toxicity of silver nanoparticles for human cells, the above observation could be of high importance for the public health.

Resin-based dental materials containing 3-aminopropyltriethoxysilane modified halloysite-clay nanotubes for extended drug delivery

OBJECTIVE

To synthesize and characterize a novel resin-based dental material containing 3-aminopropyltriethoxysilane (APTES) surface-modified halloysite-clay nanotubes (HNTs) for long-term delivery of guest molecules.

METHODS

The optimal concentrations of HNT (10, 15, 20 wt.%) and silane (0, 2, 4 vol.%sil) to be incorporated into the resin-based materials were determined (15 wt.%HNT, 4 vol.%sil) after assessment of the mechanical properties (DC%, degree of conversion; FS, flexural strength; FM, flexural modulus; and UTS, ultimate tensile strength). The HNTsil-powder was loaded with chlorhexidine (CHX) to evaluate the effect of the silanization on drug release. Resin-discs were prepared for the following groups: RES (resin), HNT (resin+15 wt.%HNT), HNTsil (resin+15 wt.%HNT silanized), HNT-CHX (resin+15 wt.%HNT loaded with chlorhexidine), HNTsil-CHX (resin+15 wt.%HNTsil-CHX), and 0.2 vol.%CHX (resin+0.2 vol.%CHX solution). Specimens were stored in water for 1, 3, 5, 10, and 15 days at 37 °C. Aliquots from each time point and the final 15-day specimens were evaluated for the zone of inhibition (ZOI) against Streptococcus mutans. CHX release was analyzed using spectrophotometry at absorbance of 300 nm. Data were statistically analyzed (α = 0.05).

RESULTS

All materials presented similar DC%. Reduced FS but increased FM was detected for 20 wt.%HNT-4%APTES. Groups with 15 wt.% and 20 wt.%HNT with/without APTES presented higher values of UTS. Agar diffusion data indicates that the HNTsil-CHX had a greater ZOI than all other groups over 15 days. HNTsil-CHX had the highest absorbance for day 1 but presented similar values to other groups every time point after.

SIGNIFICANCE

Silanization of nanotubes followed by encapsulation of chlorhexidine is a promising technique for long-term delivery of guest molecules.

Starvation Survival and Biofilm Formation under Subminimum Inhibitory Concentration of QAMs

Quaternary ammonium methacrylates (QAMs) are useful antimicrobial compounds against oral bacteria. Here, we investigated the effects of two QAMs, dimethylaminododecyl methacrylate (DMADDM) and dimethylaminohexadecyl methacrylate (DMAHDM), on biofilm formation, survival and development of tolerance by biofilm, and survival and development of tolerance against QAMs after prolonged starvation. Enterococcus faecalis (E. faecalis), Streptococcus gordonii (S. gordonii), Lactobacillus acidophilus (L. acidophilus), and Actinomyces naeslundii (A. naeslundii) were used. Minimum inhibitory concentration (MIC) of QAMs against multispecies biofilm was determined. Biofilm formed under sub-MIC was observed by crystal violet staining and confocal laser scanning microscopy (CLSM). Metabolic activity was assessed by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay and lactic acid production measurement. Development of tolerance was determined by MIC values before and after exposure to QAMs or after prolonged starvation. It was found that E. faecalis and S. gordonii could survive and form biofilm under sub-MIC of QAMs. Lactic acid production from biofilms formed under sub-MIC was significantly higher than control specimens (p < 0.05). The exposure to sub-MIC of QAMs promoted biofilm formation, and prolonged starvation or prolonged contact with sub-MIC helped bacteria develop tolerance against killing by QAMs.

Effectiveness of Riboflavin and Rose Bengal Photosensitizer Modified Adhesive Resin for Orthodontic Bonding

This study aimed to evaluate the effect of riboflavin (RF) and Rose Bengal (RB) photosensitizer modified adhesive resin on the degree of conversion (DC), and antimicrobial capacity after bonded to tooth surface. Different concentrations of RB and RF were prepared by homogenization method. An ultraviolet light source A (UVA) (375 nm wavelength, 3 mW/cm² power) was used for 30 min irradiation. FTIR was performed for control and test adhesives to analyze the DC. Antibacterial testing was performed using the MTT assay. Metal brackets were bonded using the modified adhesives and subjected for SEM examination. The surfaces of teeth and metal brackets were examined at ×10 magnification for assessing adhesive remnant index (ARI) after PDT, 24 h and thermocycling. For DC, control group, 0.1% RB and RF after PDT showed the highest value. SEM imaging indicated lowest growth of Streptococcus mutans over 0.5% of RB-PDT and RF-PDT as compared to the control group. The MTT assay outcomes reported that the activity of S. mutans substantially decreased with the addition of a high amount of either RB or RF (p < 0.01). Mean ARI scores showed a significant difference between all groups. This study concluded that 0.1% of either RB or RF after PDT can be used for bonding orthodontic brackets to the tooth surface with substantial antibacterial properties.

New Textile for Personal Protective Equipment—Plasma Chitosan/Silver Nanoparticles Nylon Fabric

Fabric structures are prone to contamination with microorganisms, as their morphology and ability to retain moisture creates a proper environment for their growth. In this work, a novel, easily processed and cheap coating for a nylon fabric with antimicrobial characteristics was developed. After plasma treatment, made to render the fabric surface more reactive sites, the fabric was impregnated with chitosan and silver nanoparticles by simply dipping it into a mixture of different concentrations of both components. Silver nanoparticles were previously synthesized using the Lee–Meisel method, and their successful obtention was proven by UV–Vis, showing the presence of the surface plasmon resonance band at 410 nm. Nanoparticles with 25 nm average diameter observed by STEM were stable, mainly in the presence of chitosan, which acted as a surfactant for silver nanoparticles, avoiding their aggregation. The impregnated fabric possessed bactericidal activity higher for Gram-positive Staphylococcus aureus than for Gram-negative Pseudomonas aeruginosa bacteria for all combinations. The percentage of live S. aureus and P. aeruginosa CFU was reduced to less than 20% and 60%, respectively, when exposed to each of the coating combinations. The effect was more pronounced when both chitosan and silver were present in the coating, suggesting an effective synergy between these components. After a washing process, the antimicrobial effect was highly reduced, suggesting that the coating is unstable after washing, being almost completely removed from the fabric. Nevertheless, the new-coated fabric can be successfully used in single-use face masks. To our knowledge, the coating of nylon fabrics intended for face-mask material with both agents has never been reported.

Microwave-Assisted Fabrication of Mesoporous Silica-Calcium Phosphate Composites for Dental Application

Herein, the microwave-assisted wet precipitation method was used to obtain materials consisting of mesoporous silica (SBA-15) and calcium orthophosphates (CaP). Composites were prepared through immersion of mesoporous silica in different calcification coating solutions and then exposed to microwave radiation. The composites were characterized in terms of molecular structure, crystallinity, morphology, chemical composition, and mineralization potential by Fourier-transform infrared spectroscopy (FTIR), powder X-ray diffraction (XRD), and scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy (SEM-EDX). The application of microwave irradiation resulted in the formation of different types of calcium orthophosphates such as calcium deficient hydroxyapatite (CDHA), octacalcium phosphate (OCP), and amorphous calcium phosphate (ACP) on the SBA-15 surface, depending on the type of coating solution. The composites for which the progressive formation of hydroxyapatite during incubation in simulated body fluid was observed were further used in the production of final pharmaceutical forms: membranes, granules, and pellets. All of the obtained pharmaceutical forms preserved mineralization properties.

Antimicrobial capacity and physico-chemical characteristics of adhesive resin containing riboflavin after photodynamic therapy

PURPOSE

To assess the micro-tensile bond strength (μ-TBS), degree of conversion, and antimicrobial capacity of modified dentin adhesive using riboflavin photoinitiators.

MATERIALS AND METHODS

Three groups of adhesives (control; 0.1 % riboflavin-PDT and 0.5 % riboflavin PDT) were prepared and tested on 70 sound molar teeth. Fourier-transformed infrared spectroscopy (FTIR) was performed for riboflavin and riboflavin-modified adhesives to calculate the degree of conversion. Contact angle measurement was performed by dropping a 5 μL droplet of the adhesives onto polished dentin disk. For μ-TBS testing, the dentin beams were fixed on a micro-tensile tester and were loaded in tension at a cross-head speed of 1 mm per min until fracture. The viability of Streptococcus mutans biofilm was tested using MTT assay.

RESULTS

The spectrum at 1728 cm-1 indicates CO stretching frequency of riboflavin. The groups control and 0.1 % riboflavin PDT showed the highest degree of conversion followed by lowest degree of conversion of 0.5 % riboflavin adhesive after PDT. The control adhesive exhibited the highest contact angle over the dentin surface compared to the riboflavin-modified adhesive groups (p < 0.05). The lowest contact angle was observed for 0.1 % riboflavin that showed increased permeability of the adhesive onto the dentin surface (p < 0.05). The variables of immediate bonding (F = 12.328, p = 0.000) and ageing in artificial saliva (F = 41.559, p = 0.000) significantly affected the bond strength. For aged μ-TBS testing, the scores for 0.1 % riboflavin PDT was significantly higher as compared to the 0.5 % riboflavin PDT samples. The MTT resulted in a lower S. mutans viability for 0.5 % riboflavin PDT compared to 0.1 % riboflavin PDT and control adhesive (p < 0.05), irrespective of any time point, that is, after 24 h and 30 days ageing.

CONCLUSIONS

The addition of riboflavin as photosensitizer in dentin adhesive demonstrated higher bond strength, excellent antimicrobial capability, and degree of conversion following PDT. The addition of riboflavin in dentin adhesive for PDT could be used as a potential restorative material in adhesive dentistry.

Bibliometric Analysis of Literature Published on Antibacterial Dental Adhesive from 1996-2020

This study aimed to investigate the current state of research on antibacterial dental adhesives. The interest in this field can be drawn from an increasing number of scholarly works in this area. However, there is still a lack of quantitative measurement of this topic. The main aim of this study was to consolidate the research published on the antibacterial adhesive from 1996 to 2020 in Web of Science indexed journals. The bibliometric method, a quantitative study of investigating publishing trends and patterns, was used for this study. The result has shown that a gradual increase in research was found, whereby a substantial increase was observed from 2013. A total of 248 documents were published in 84 journals with total citations of 5107. The highly cited articles were published mainly in Q1 category journals. Most of the published articles were from the USA, China, and other developed countries; however, some developing countries contributed as well. The authorship pattern showed an interdisciplinary and collaborative approach among researchers. The thematic evaluation of keywords along with a three-factor analysis showed that 'antibacterial adhesives' and 'quaternary ammonium' have been used commonly. This bibliometric analysis can provide direction not only to researchers but also to funding organizations and policymakers.