Dye decolorization and detoxification potential of Ca-alginate beads immobilized manganese peroxidase

Kinetics of dye decolorization using heterogeneous catalytic system with immobilized Achromobacter xylosoxidans DDB6

Textile effluents containing toxic dyes must be treated effectively before discharge to prevent adverse environmental impacts. Traditional physical and chemical treatment methods are costly and generate secondary pollutants. In contrast, biological treatment is a more suitable, clean, versatile, eco-friendly, and cost-effective technique for treating textile effluent. It is well established that indigenous microbial populations present in effluents can effectively degrade toxic dyes. In this regard, Achromobacter xylosoxidans DDB6 was isolated from the effluent sample to decolorize crystal violet (CV), Coomassie brilliant blue (CBB), and alizarin red (AR) by 67.20%, 28.58%, and 20.41%, respectively. The growth parameters of A. xylosoxidans DDB6 in media supplemented with 100 ppm of various dyes were determined using the modified Gompertz growth model. The immobilized cells in calcium alginate beads showed apparent decolorization rate constant of 0.27, 0.18, and 0.13 h-1 for CV, CBB, and AR, respectively. The immobilized cells in a packed bed reactor with an optimum flow rate of 0.5 mL/min were used to treat 100 ppm of CV with a percentage decolorization of 79.47% after three cycles. Based on the findings, A. xylosoxidans DDB6 could be effectively used for decolorization of various dyes.

A Co-Immobilized Enzyme-Mediator System for Facilitating Manganese Peroxidase Catalysis in Solution Free of Divalent Manganese Ions

Manganese peroxidase (MnP) offers significant potential in various environmental and industrial applications; however, its reliance on Mn2+ ions for electron shuttling limits its use in Mn2+-deficient systems. Herein, a novel approach is presented to address this limitation by co-immobilizing MnP and Mn2+ in silica gels. These gels were synthesized following the standard sol-gel method and found to effectively immobilize Mn2+ ions, primarily through electrostatic interactions. The MnP co-immobilized with Mn2+ ions in the silica gel exhibited 4-5 times higher activity than the MnP immobilized alone in activity assays, and generated Mn3+ within the gel, indicating the immobilized Mn2+ ions remain capable of shuttling electrons to the co-immobilized MnP. In decolorization tests with two organic dyes, the co-immobilized system also outperformed the MnP immobilized without Mn2+ ions, resulting in 2-4 times higher dye removals. This study will enable a broader application of MnP enzymes in sustainable environmental remediation and industrial catalysis.

Immobilization of Horseradish Peroxidase on Ca Alginate-Starch Hybrid Support: Biocatalytic Properties and Application in Biodegradation of Phenol Red Dye

In this study, horseradish peroxidase was extracted, purified, and immobilized on a calcium alginate-starch hybrid support by covalent bonding and entrapment. The immobilized HRP was used for the biodegradation of phenol red dye. A 3.74-fold purification was observed after precipitation with ammonium sulfate and dialysis. An immobilization yield of 88.33%, efficiency of 56.89%, and activity recovery of 50.26% were found. The optimum pH and temperature values for immobilized and free HRP were 5.0 and 50 °C and 6.5 and 60 °C, respectively. The immobilized HRP showed better thermal stability than its free form, resulting in a considerable increase in half-life time (t1/2) and deactivation energy (Ed). The immobilized HRP maintained 93.71% of its initial activity after 45 days of storage at 4 °C. Regarding the biodegradation of phenol red, immobilized HRP resulted in 63.57% degradation after 90 min. After 10 cycles of reuse, the immobilized HRP was able to maintain 43.06% of its initial biodegradative capacity and 42.36% of its enzymatic activity. At the end of 15 application cycles, a biodegradation rate of 8.34% was observed. In conclusion, the results demonstrate that the immobilized HRP is a promising option for use as an industrial biocatalyst in various biotechnological applications.

Immobilization of commercial horseradish peroxidase in calcium alginate-starch hybrid support and its application in the biodegradation of phenol red dye

In this study, horseradish peroxidase (HRP) was immobilized for the first time on Ca alginate-starch hybrid beads and employed for the biodegradation of phenol red dye. The optimal protein loading was 50 mg/g of support. Immobilized HRP demonstrated improved thermal stability and maximum catalytic activity at 50 °C and pH 6.0, with an increase in half-life (t1/2) and enzymatic deactivation energy (Ed) compared to free HRP. After 30 days of storage at 4 °C, immobilized HRP retained 109% of its initial activity. Compared to free HRP, the immobilized enzyme exhibited higher potential for phenol red dye degradation, as evidenced by the removal of 55.87% of initial phenol red after 90 min, which was 11.5 times greater than free HRP. In sequential batch reactions, the immobilized HRP demonstrated good potential efficiency for the biodegradation of phenol red dye. The immobilized HRP was used for a total of 15 cycles, degrading 18.99% after 10 cycles and 11.69% after 15 cycles, with a residual enzymatic activity of 19.40% and 12.34%, respectively. Overall, the results suggest that HRP immobilized on Ca alginate-starch hybrid supports shows promise as a biocatalyst for industrial and biotechnological applications, particularly for the biodegradation of recalcitrant compounds such as phenol red dye.

Manganese peroxidases as robust biocatalytic tool - An overview of sources, immobilization, and biotechnological applications

With robust catalytic features, manganese peroxidases (MnPs) from various sources, including fungi and bacteria, have gained much consideration in many biotechnological applications with particular emphasis on environmental remediation. MnP is a heme-containing enzyme that belongs to the oxidoreductases that can catalyze the degradation of various organic pollutants, such as chlorophenols, nitroaromatic compounds, industrial dyes, and polycyclic aromatic hydrocarbons. To spotlight the MnP as biocatalytic tool, an effort has been put forward to cover the four major compartments. For instance, following a brief introduction, first, various microbial sources of MnP are discussed with examples. Second, structural attributes and biocatalytic features of MnP are given with examples. Third, different MnP immobilization strategies, including adsorption, covalent linking, entrapment, and cross-linking, are discussed with a significant motive to strengthen the enzyme's stability against diverse deactivation agents by restricting the conformational mobility of molecules. Compared to free counterparts, immobilized MnP fractions perform well in hostile environments. Finally, various biotechnological applications, such as fuel ethanol production, de-lignification, textile industry, pulp and paper industry, degradation of phenolic and non-phenolic compounds, and pharmaceutical and pesticide degradation, are briefly discussed.

Biocatalytic degradation of reactive blue 221 and direct blue 297 dyes by horseradish peroxidase immobilized on iron oxide nanoparticles with improved kinetic and thermodynamic characteristics

In present study, we describe the biodegradation of direct blue (DB) 297 and reactive blue (RB) 221 by immobilizing horseradish peroxidase (HRP) isolated from fresh leaves of Moringa Oliefera on iron oxide nanoparticles. Iron oxide nanoparticles were synthesized by co-precipitation method and showed a maximum immobilization efficiency of 87%. The surface topography of iron oxide nanoparticles was envisaged by scanning electron microscopy (SEM), results showed that magnetic nanoparticles (MNPs) were in the form of aggregates having size of 1 μm. Furthermore, immobilization was confirmed via functional group identification performed by Fourier transformed infrared spectroscopy (FTIR). Immobilization phenomena displaced the optimum temperature from 35 °C to 50 °C moreover, pH optima were altered from 5.0 to 7.0. Vmax and Km for free and immobilized HRP, were 303 U/mg and 1.66 mM and 312 U/mg and 1.94 mM, respectively. Enzymatic thermodynamic measurements (ΔH*, ΔS*, Ea, ΔG*) were also evaluated for immobilized HRP and its free counterpart. Optimum degradation of reactive blue (RB) and direct blue (DB) 297 with free and immobilized HRP was observed at pH 5 and at temperature 40 °C respectively. The removal efficiency of DB 297 and RB 221 with free HRP was 75% and 86% while with immobilized HRP was 81% and 92% respectively. Furthermore, biodegradation of reactive blue (RB) 221 and direct blue (DB) 297 with immobilized and free biocatalyst was also investigated by Fourier transform infrared spectroscopy (FTIR) by identification of groups involved in dye degradation. FTIR results confirmed the 100% degradation of dyes. Immobilized HRP retained significant catalytic activity after five consecutive cycles of dye degradation. In conclusion, Fe3O4 nanoparticles are promising and environmentally friendly media for enzyme immobilization. Moreover, immobilized HRP showed more thermal stability, pH stability and higher dye degradation efficiency as compared to free HRP. Furthermore, the immobilized HRP, economically more convenient and easily removable from reaction media. Owing to its thermal stability, ease of separation from reaction media and reusability, the magnetically separatable immobilized HRP can be exploited successfully for treatment of dye contaminated textile effluents.

Bioremoval and Detoxification of the Anticancer Drug Mitoxantrone Using Immobilized Crude Versatile Peroxidase (icVP/Ba) Bjerkandera adusta CCBAS 930

The aim of this study was to evaluate the biodecolorization and detoxification of the anticancer drug mitoxantron (MTX) by immobilized crude versatile peroxidase of Bjerkandera adusta CCBAS 930 (icVP/Ba). The concentrated crude VP was obtained from B. adusta CCBAS 930 culture on medium with MTX (µg/mL) addition, immobilized with 4% sodium alginate. MTX removal degree (decolorization), levels of phenolic compounds and free radicals were determined during MTX biotransformation. Moreover, the phytotoxicity (Lepidium sativum L.), biotoxicity (multi-species microbial assay, MARA), and genotoxicity (SOS Chromotest) of MTX were evaluated before and after the biological treatment. The use of icVP/Ba (95 U/mL) significantly shortened the bioremoval of 10 µg/mL MTX (95.57% after 72 h). MTX removal by icVP/Ba was correlated with an 85% and 90% decrease in the levels of phenolic compounds and free radicals, respectively. In addition, the use of icVP/Ba contributed to a decrease in the phyto-, bio-, and genotoxicity of MTX. This is the first study to describe the possibility of removing MTX using immobilized crude fungal peroxidase.

A systematic study of cellulose-reactive anionic dye removal using a sustainable bioadsorbent

Cellulose-reactive anionic dyes are one of the dominant colorants used in textile finishing. Unfortunately, they also produce large quantities of wastewater that must be treated before discharge, demanding low-cost and sustainable adsorbents that can easily be implemented, especially for developing countries with thriving cotton-based textile sectors. In this study, a high specific surface area (670 m²/g) water hyacinth root powder (WHRP) bioadsorbent that is neither carbonized nor activated was prepared to remove cellulose-reactive anionic blue dye from an aqueous solution. The effect of adsorption pH (pH = 2-8), adsorbent dose (1 g/L-6 g/L), dye concentration (50 mg/L-500 mg/L), adsorbent particle size (50 μm-1000 μm), mixing speed (100 rpm -200 rpm), and adsorption temperatures (22 °C-60 °C) were systematically studied. It was found that the protonation of lignin polyphenols in WHRP at pH = 2 was responsible for the observed high (∼99%) adsorptive removal of reactive blue dye. The maximum equilibrium adsorption capacity was 128.8 mg/g when 1 g/L WHRP and 500 mg/L dye concentration were used. In addition, adsorption isotherms, kinetic models, and adsorption thermodynamics were investigated. Increasing adsorbent dose, decreasing adsorbent particle size, increasing mixing speed, and lowering temperature favored the adsorption of reactive dye to WHRP adsorbent. The batch adsorption data were best fitted with both Langmuir and Temkin models, especially at 22 °C, while the adsorption kinetic behavior was described best using pseudo-second-order kinetics. Adsorption of cellulose-reactive blue dye to WHRP was spontaneous as characterized by the negative Gibbs energy (-11 kJ/mol to -24 kJ/mol) and exothermic with negative enthalpy (-13 kJ/mol to -23 kJ/mol). The overall adsorption process was controlled by more than one mechanism since the intraparticle diffusion was not the only rate-limiting step under our experimental conditions. Taken together, the abundantly available and sustainable WHRP is an efficient adsorbent that could be scaled up for treating cellulose-reactive dye-contaminated water.

Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation

The aim of this study was to investigate covalent immobilization of horseradish peroxidase (HRP) on magnetic nanoparticles (Mag) encapsulated in calcium alginate beads (MABs) for color degradation, combining easy and fast removal of biocatalyst from the reaction mixture due to its magnetic properties and strong binding due to surface alginate functional groups. MABs obtained by extrusion techniques were analyzed by optical microscopy, FEG-SEM and characterized regarding mechanical properties, magnetization and HRP binding. HRP with initial concentration of 10 mg/g_carrier was successfully covalently bonded on MABs (diameter ~1 mm, magnetite/alginate ratio 1:4), with protein loading of 8.9 mg/g_carrier, immobilization yield 96.9% and activity 32.8 U/g. Immobilized HRP on MABs (HRP-MABs) was then used to catalyze degradation of two anthraquinonic dyes, Acid Blue 225 (AB225) and Acid Violet 109 (AV109), as models for wastewater pollutants. HRP-MABs decolorized 77.3% and 76.1% of AV109 and AB225, respectively after 15 min under optimal conditions (0.097 mM H₂O₂, 200 mg of HRP-MABs (8.9 mg/g_carrier), 0.08 and 0.1 g/mg beads/dye ratio for AV109 and AB225, respectively). Biocatalyst was used for 7 repeated cycles retaining 75% and 51% of initial activity for AB225 and AV109, respectively, showing potential for use in large scale applications for colored wastewater treatment.

Non-magnetic and magnetically responsive support materials immobilized peroxidases for biocatalytic degradation of emerging dye pollutants-A review

In recent years, the removal of hazardous pollutants from many industries has become a significant challenge for mankind as a growing number of contaminants, including a wide range of organic pollutants, synthetic dyes, and polycyclic aromatic hydrocarbons (PAHs), have inevitably led to an increased anthropogenic impact on the biosphere. Due to the complex aromatic structure, most synthetic dyes show resistance to degrade by the classical approaches, such as coagulation, flotation, adsorption, membrane process, and reverse osmosis. Enzyme-assisted biodegradation of pollutants offers an eco-friendlier and cost-effective alternative to remediate dyes, dyes-based effluents, other toxins, etc. Various plant and microbial oxidoreductase (Horseradish and manganese peroxidase) have recently received more attention for degrading and detoxifying a wide range of dyes either by opening the aromatic ring structure or by precipitation due to their high activity under milder conditions, high substrate specificity, and biodegradable nature. To enhance the efficiency, stability and recyclability, enzymes were immobilized on various support media such as sodium alginate, agarose, chitin/chitosan, polyvinyl alcohol, polyacrylamide, macroporous exchange resins, hydrophobic sol-gels, and nanoporous silica gel, including magnetically separatable media. Among various types of magnetic nanoparticles (MNPs), iron oxide magnetic nanoparticles, such as hematite, magnetite, and maghemite, have gained great attention due to their properties like small size, superparamagnetism, high surface area to volume ratio, and ease of separation for repeated cycles of uses. These carriers can be separated easily and rapidly from the reaction medium by an external magnetic field without being subjected to mechanical stress than centrifugation or filtration. Various methods have been employed for immobilizing oxidoreductase on different media, such as adsorption, covalent binding, entrapment, and encapsulation using different cross-linking agents. Compared to the free enzyme, insolubilized enzymes reduce production costs by enzyme reusability, tolerance to unfavorable environmental conditions, and high catalytic stability. Here, we review various immobilization methods and biocatalytic degradation of emerging dye pollutants, focusing on various non-magnetically and magnetically responsive supports to immobilize peroxidases. Conclusively, magnetically separatable peroxidases show more stability towards extreme temperature and pH conditions and can be used for repeated cycles than free and non-magnetically separatable peroxidase.

Biological remediation technologies for dyes and heavy metals in wastewater treatment: New insight

The pollution of the environment caused by dyes and heavy metals emitted by industries has become a worldwide problem. The development of efficient, environmentally acceptable, and cost-effective methods of wastewater treatment containing dyes and heavy metals is critical. Biologically based techniques for treating effluents are fascinating since they provide several benefits over standard treatment methods. This review assesses the most recent developments in the use of biological based techniques to remove dyes and heavy metals from wastewater. The remediation of dyes and heavy metals by diverse microorganisms such as algae, bacteria, fungi and enzymes are depicted in detail. Ongoing biological method's advances, scientific prospects, problems, and the future prognosis are all highlighted. This review is useful for gaining a better integrated view of biological based wastewater treatment and for speeding future research on the function of biological methods in water purification applications.

Effective utilization of magnetic nano-coupled cloned β-xylanase in saccharification process

The β-xylanase gene (DCE06_04615) with 1041 bp cloned from Thermotoga naphthophila was expressed into E. coli BL21 DE3. The cloned β-xylanase was covalently bound to iron oxide magnetic nanoparticles coated with silica utilizing carbodiimide. The size of the immobilized MNPs (50 nm) and their binding with β-xylanase were characterized by Fourier-transform electron microscopy (FTIR) (a change in shift particularly from C–O to C–N) and transmission electron microscopy (TEM) (spherical in shape and 50 nm in diameter). The results showed that enzyme activity (4.5 ± 0.23 U per mL), thermo-stability (90 °C after 4 hours, residual activity of enzyme calculated as 29.89% ± 0.72), pH stability (91% ± 1.91 at pH 7), metal ion stability (57% ± 1.08 increase with Ca²⁺), reusability (13 times) and storage stability (96 days storage at 4 °C) of the immobilized β-xylanase was effective and superior. The immobilized β-xylanase exhibited maximal enzyme activity at pH 7 and 90 °C. Repeated enzyme assay and saccharification of pretreated rice straw showed that the MNP-enzyme complex exhibited 56% ± 0.76 and 11% ± 0.56 residual activity after 8 times and 13 times repeated usage. The MNP-enzyme complex showed 17.32% and 15.52% saccharification percentage after 1^st and 8^th time usage respectively. Immobilized β-xylanase exhibited 96% residual activity on 96 days' storage at 4 °C that showed excellent stability.

The β-xylanase gene (DCE06_04615) with 1041 bp cloned from Thermotoga naphthophila was expressed into E. coli BL21 DE3.

Removal of Emerging Contaminants from Wastewater Streams Using Membrane Bioreactors: A Review

Water is a very valuable natural resource. As the demand for water increases the presence of emerging contaminants in wastewater has become a growing concern. This is particularly true when one considers direct reuse of wastewater. Obtaining sufficient removal of emerging contaminants will require determining the level of removal for the various unit operations in the wastewater treatment process. Membrane bioreactors are attractive as they combine an activated sludge process with a membrane separation step. They are frequently used in a wastewater treatment process and can operate at higher solid loadings than conventional activated sludge processes. Determining the level of removal of emerging contaminants in the membrane bioreactor step is, therefore, of great interest. Removal of emerging contaminants could be by adsorption onto the biomass or membrane surface, biotransformation, size exclusion by the membrane, or volatilization. Given the fact that most emerging contaminants are low molecule weight non-volatile compounds, the latter two methods of removal are usually unimportant. However, biotransformation and adsorption onto the biomass are important mechanisms of removal. It will be important to determine if the microorganisms present at given treatment facility are able to remove ECs present in the wastewater.

Enhanced Efficiency of the Removal of Cytostatic Anthracycline Drugs Using Immobilized Mycelium of Bjerkandera adusta CCBAS 930

The aim of this study was to evaluate the bioremoval of anthracycline antibiotics (daunomycin-DNR, doxorubicin-DOX, and mitoxantrone-MTX) by immobilized mycelium of B. adusta CCBAS 930. The activity of oxidoreductases: versatile peroxidases (VP), superoxide dismutase (SOD), catalase (CAT), and glucose oxidase (GOX), and the levels of phenolic compounds (PhC) and free radicals (SOR) were determined during the biotransformation of anthracyclines by B. adusta strain CCBAS 930. Moreover, the phytotoxicity (Lepidium sativum L.), biotoxicity (MARA assay), and genotoxicity of anthracyclines were evaluated after biological treatment. After 120 h, more than 90% of anthracyclines were removed by the immobilized mycelium of B. adusta CCBAS 930. The effective biotransformation of anthracyclines was correlated with detoxification and reduced genotoxicity.

Enzyme-assisted bioremediation approach for synthetic dyes and polycyclic aromatic hydrocarbons degradation

Environmental protection from emerging pollutants has become a significant challenge for mankind as an increasing number of contaminants, including synthetic dyes and polycyclic aromatic hydrocarbons (PAHs), represent a serious risk to ecological and environmental balance. Most synthetic dyes have complex aromatic structures and are resistant to degrade by classical approaches, such as physical and chemical processes, including adsorption, chemical coagulation, flocculation, ion exchange, membrane separation, froth flotation, and reverse osmosis. Enzymes-assisted catalytic transformation of pollutants has become a potential alternative to classical methods because of their ability to react with complex compounds, a quick degradation rate, and producing less harmful by-products. Plant peroxidases, and microbial laccase and lignin-degrading peroxidases (manganese and lignin peroxidase) have gained significant attention for treating aromatic waste due to their capability of oxidizing and detoxifying a wide range of recalcitrant xenobiotics, including PAHs and synthetic dyes. Peroxidases being efficient biocatalysts detoxify an array of toxic compounds by simple free-radical mechanism resulting in the formation of oxidized and depolymerized products of significantly reduced toxicity. Moreover, it is an ecofriendly and economically favorable approach towards the biodegradation of recalcitrant and toxic industrial waste. Among microbial and plant peroxidases, bacterial enzymes have broad substrate specificity and can transform a wide range of recalcitrant substrates. Ligninolytic enzymes oxidize the aromatic ring into quinones and acids by producing free hydroxyl radicals instead of dihydrodiols and mineralize aromatic hydrocarbon in combination with cytochrome P450, monooxygenases, and epoxide hydrolases. In the review, an attempt has been made to provide detailed knowledge about the availability of inexpensive peroxidases sources, their mechanism of action, and degradation potential. The present review summarizes the exploitation of peroxidases from plants, bacteria, and fungus (manganese peroxidase, lignin peroxidase, and laccases) for detoxification and degradation of textile dyes as well as PAHs. Conclusively, peroxidases have great potential to react with almost all classes of synthetic dyes and most PAHs due to broad substrate specificity and transformed them into less harmful metabolites.

Textile Dye Biodecolorization by Manganese Peroxidase: A Review

Wastewater emissions from textile factories cause serious environmental problems. Manganese peroxidase (MnP) is an oxidoreductase with ligninolytic activity and is a promising biocatalyst for the biodegradation of hazardous environmental contaminants, and especially for dye wastewater decolorization. This article first summarizes the origin, crystal structure, and catalytic cycle of MnP, and then reviews the recent literature on its application to dye wastewater decolorization. In addition, the application of new technologies such as enzyme immobilization and genetic engineering that could improve the stability, durability, adaptability, and operating costs of the enzyme are highlighted. Finally, we discuss and propose future strategies to improve the performance of MnP-assisted dye decolorization in industrial applications.

Recent Advances in Enzymes for the Bioremediation of Pollutants

Nowadays, pollution of the environment is a huge problem for humans and other organisms' health. Conventional methods of pollutant removal like membrane filtration or ion exchange are not efficient enough to lower the number of pollutants to standard levels. Biological methods, because of their higher efficiency and biocompatibility, are preferred for the remediation of pollutants. These cost-effective and environment-friendly methods of reducing pollutants are called bioremediation. In bioremediation methods, enzymes play the most crucial role. Enzymes can remedy different types of organic and inorganic pollutants, including PAHs, azo dyes, polymers, organocyanides, lead, chromium, and mercury. Different enzymes isolated from various species have been used for the bioremediation of pollutants. Discovering new enzymes and new subtypes with specific physicochemical characteristics would be a promising way to find more efficient and cost-effective tools for the remediation of pollutants.

Immobilized Soybean Peroxidase Hybrid Biocatalysts for Efficient Degradation of Various Emerging Pollutants

In the present study, soybean peroxidase (SBP) was covalently immobilized onto two functionalized photocatalytic supports (TiO2 and ZnO) to create novel hybrid biocatalysts (TiO2-SBP and ZnO-SBP). Immobilization caused a slight shift in the pH optima of SBP activity (pH 5.0 to 4.0), whereas the free and TiO2-immobilized SBP showed similar thermal stability profiles. The newly developed hybrid biocatalysts were used for the degradation of 21 emerging pollutants in the presence and absence of 1-hydroxy benzotriazole (HOBT) as a redox mediator. Notably, all the tested pollutants were not equally degraded by the SBP treatment and some of the tested pollutants were either partially degraded or appeared to be recalcitrant to enzymatic degradation. The presence of HOBT enhanced the degradation of the pollutants, while it also inhibited the degradation of some contaminants. Interestingly, TiO2 and ZnO-immobilized SBP displayed better degradation efficiency of a few emerging pollutants than the free enzyme. Furthermore, a combined enzyme-chemical oxidation remediation strategy was employed to degrade two recalcitrant pollutants, which suggest a novel application of these novel hybrid peroxidase-photocatalysts. Lastly, the reusability profile indicated that the TiO2-SBP hybrid biocatalyst retained up to 95% degradation efficiency of a model pollutant (2-mercaptobenzothiazole) after four consecutive degradation cycles.

Immobilization of yeast cell walls with surface displayed laccase from Streptomyces cyaneus within dopamine-alginate beads for dye decolorization

High amounts of toxic textile dyes are released into the environment due to coloring and wastewaters treatment processes' inefficiency. To remove dyes from the environment and wastewaters, researchers focused on applying immobilized enzymes due to mild reaction conditions and enzyme nontoxicity. Laccases are oxidases with wide substrate specificity, capable of degradation of many different dye types. Laccase from Streptomyces cyaneus was expressed on the surface of Saccharomyces cerevisiae EBY100 cells. The specific activity of surface-displayed laccase was increased by toluene-induced lysis to 3.1 U/g of cell walls. For cell wall laccase immobilization within hydrogel beads, alginate was modified by dopamine using periodate oxidation and reductive amination and characterized by UV-Vis, FTIR, and NMR spectroscopy. Cell wall laccase was immobilized within alginate and dopamine-alginate beads additionally cross-linked by oxygen and laccase. The immobilized enzyme's specific activity was two times higher using dopamine-alginate compared to native alginate beads, and immobilization yield increased 16 times. Cell wall laccase immobilized within dopamine-alginate beads decolorized Amido Black 10B, Reactive Black 5, Evans Blue, and Remazol Brilliant Blue with 100% efficiency and after ten rounds of multiple-use retained decolorization efficiency of 90% with Evans Blue and 61% with Amido Black.

Degradation of moxifloxacin by ionizing radiation and toxicity assessment

The gamma ray induced degradation of moxifloxacin in aqueous media has been evaluated. The drug solutions (50 & 100 mg/L) were irradiated to absorbed doses of 0.3, 0.6, 0.9, 1.2, 1.5, 2, 3 and 4 kGy using Cs-137 gamma radiation source. The parameters such as drug initial concentration, oxidant (H2O2) concentration and gamma ray absorbed doses were optimized. The efficiency of Advanced oxidation processes (AOP) was evaluated on the basis of degradation, reduction in chemical oxygen demand (COD) and toxicity reduction of the drug. The maximum degradation of 94.01 and 88.30% was achieved when drug solutions were exposed to gamma irradiation absorbed dose of 4 kGy which enhanced to 100 and 99.06% in the presence of H2O2 (0.5 mL/L) for 50 and 100 mg/L respectively. A significant reduction in COD 72 and 75% for 50 mg/L while 65 and 69% in case of 100 mg/L was noted using gamma and gamma/H2O2 respectively at absorbed dose of 4 kGy. The parameters such as dose constant (k), removal efficiency (G-value), gamma ray absorbed doses required for 50, 90 and 99% degradation (D 0.50, D 0.90 and D 0.99) have been calculated. The radiolytic degradation was monitored by UV–Vis spectrophotometer and HPLC, FT-IR studies were performed to investigate the change in functional groups before and after treatment, while GC-MS analysis was carried out to monitor intermediates/degraded end-products. The FT-IR spectra has shown complete destruction of aromatic rings after radiation treatment but a minor peak appeared at 1216 cm−1 corresponding to CO stretching. The GC-MS study for the drug samples treated with gamma/H2O2 has shown no any significant peak which confirms the complete degradation. The cytotoxicity of treated samples was carried out by hemolytic assay and mutagenicity using Ames test before and after each treatment. The hemolytic test showed 73.92% hemolysis, while gamma/H2O2 treatment reduced the mutagenicity to 74.08 and 65.66% against TA98 and TA100 bacterial strains respectively. The response surface methodology (RSM) was employed to optimize the data. The obtained data elaborate that gamma/H2O2process is promising approach for the remediation of pharmaceutical waste effluent.

Utilization of different polymers for the improvement of catalytic properties and recycling efficiency of bacterial maltase

Current study deals with the comparative study related to immobilization of maltase using synthetic (polyacrylamide) and non-synthetic (calcium alginate, agar-agar and agarose) polymers via entrapment technique. Polyacrylamide beads were formed by cross-linking of monomers, agar-agar and agarose through solidification while alginate beads were prepared by simple gelation. Results showed that the efficiency of enzyme significantly improved after immobilization and among all tested supports agar-agar was found to be the most promising and biocompatible for maltase in terms of immobilization yield (82.77%). The catalytic behavior of maltase was slightly shifted in terms of reaction time (free enzyme, agarose and polyacrylamide: 5.0 min; agar-agar and alginate: 10.0 min), pH (free enzyme, alginate and polyacrylamide: 6.5; agar-agar, agarose: 7.0) and temperature (free enzyme: 45 °C; alginate: 50 °C; polyacrylamide: 55 °C; agarose: 60 °C; agar-agar: 65 °C). Stability profile of immobilized maltase also revealed that all the supports utilized have significantly enhanced the activity of maltase at higher temperatures then its free counterpart. However, recycling data showed that agar-agar entrapped maltase retained 20.0% of its initial activity even after 10 cycles followed by agarose (10.0%) while polyacrylamide and alginate showed no activity after 8 and 6 cycles respectively.

Fungal biosynthesis of lignin-modifying enzymes from pulp wash and Luffa cylindrica for azo dye RB5 biodecolorization using modeling by response surface methodology and artificial neural network

This study demonstrates the evaluation between the artificial neural network technique coupled to the genetic algorithm (ANN-GA) and the response surface methodology (RSM) for prediction of Reactive Black 5 (RB5) decolorization by crude enzyme from Pleurotus. sajor-caju. Fungal lignin-modifying enzymes (FLME) were synthesized using pulp wash (PW) as an inducing substrate, and L. cylindrica (L.C) for cell immobilization. When grown in PW, the fungus showed higher Lac activity (126.5 IU. mL^-1), whereas when immobilized a higher MnP activity was achieved (22.79 IU. mL^-1), but both methods were capable of decolorizing the dye in about 89.4 % and 75 %, respectively. This indicates applicability of PW as an alternative substrate for FLME induction and viability of immobilization for MnP synthesis. For RB5 decolorization, the action of the crude enzyme extract was considered as a function of pH, dye concentration, temperature, and reaction time. The models are well adjusted to predict the efficiency of biodecolorization, with no statistical difference between ANN-GA and RSM, which indicates potential for green enzymes prospecting application in bioprocess industry.

Kinetics of a fixed bed reactor with immobilized microorganisms for the removal of organic matter and phosphorous

The biodegradation of domestic wastewater contaminants has been carried out using microorganisms immobilized in sodium alginate gel (Alg-Na). A fixed bed reactor with immobilized microorganisms was used for the treatment of domestic wastewater. A wastewater pretreatment was carried out to remove the larger particulate matter, which consisted of a reactor packed with different materials (anthracite, zeolite, and activated carbon). Later, a second reactor packed with balls with immobilized microorganisms was used to eliminate organic matter and nutrients. 2.5% w/v of Alg-Na was used as a support to immobilize the microorganisms. According to the results, a total phosphorus (TP) and chemical oxygen demand (COD) removal of 94.26% and 78.25% was obtained, respectively. In addition, the degradation rate for both organic matter and phosphorous was studied by using the kinetic model for fix bed reactor. © 2020 Water Environment Federation PRACTITIONER POINTS: Phosphorous and organic matter removal by adsorption and immobilized microorganisms. High removal efficiency of phosphorous and organic matter was found. An innovative wastewater treatment alternative is proposed. Kinetic model for fixed bed reactor is also proposed for scaling-up purposes.

Immobilization of fluorescent bacterial bioreporter for arsenic detection

Whole-cell bacterial biosensors hold great promise as a practical complementary approach for in-field detection of arsenic. Although there are various bacterial bioreporter systems for arsenic detection, fewer studies reported the immobilization of arsenic bioreporters. This study aimed at determining immobilization of specific bacterial bioreporter in agar and alginate biopolymers to measure level of arsenite and/or arsenate. To achieve sensitive detection, immobilization parameters of polymer concentration and cell density were evaluated. Moreover, by changing the culture medium, immobilized bioreporter cells in minimal medium can detect arsenite while they can detect both arsenite and arsenate in phosphate-limited minimal medium. When optimal parameters were applied, agar and alginate immobilized bioreporter systems can detect arsenite and arsenate concentrations of 10 μg/l and 200 μg/l within 5 h and 2 h, respectively. The results showed that the immobilized bacterial bioreporter systems are able to determine the concentrations of the two abundant species of arsenic; arsenite and arsenate, as opposed to other studies which reported only arsenite detection. This is the first study describe agar hydrogel and alginate bead immobilization of fluorescent arsenic bacterial bioreporter that can detect both arsenite and arsenate at the safe drinking water limit. Thus, this study will enable further steps to be taken towards developing sensitive and selective portable devices to assess environmental arsenic contamination and prevent acute arsenic toxicity.

Environmentally responsive and anti-bugs textile finishes - Recent trends, challenges, and future perspectives

Bugs, such as microorganisms and insects, are present in the environment and sometimes can be health-hazardous if the living environment is not maintained following proper hygienic regulations. In the present scenario of increasing public awareness, environmental consciousness, and growing demand for easy-care, and disinfected textiles, the manufacturing of protective and easy-to-care textiles has become a key necessity of the modern world. Comfortable, clean, hygienic, antimicrobial, and insect repelling properties of textile goods are gaining the accelerating research momentum as a basic requirement to produce multifunctional textiles. These functional finishes have numerous applications such as in-home textiles, bed nets, and tenting, camping gear as well as in military uniforms. Synthetic antimicrobial and insect repellents are quite effective against insects and microscopic organisms but are slightly toxic to the human being and the environment. To overcome these problems, researchers are considering natural agents for functional finishes, but their effectiveness is less durable to textile material. Besides needful advantages, the excessive use of dyes in finishing processes heavily required washing cycles and ultimately release various types of hazardous dyes or wasteful effluents in the environment. This review reports the chemical composition and recent developments in textile finishes, particularly antimicrobial and insect repellent textile finishes. A large number of commonly used antimicrobial agents (i.e. chitosan, zwitterionic compounds, silver and silver-based compounds, titanium dioxide nanoparticles, imidazolium salts, triclosan and quaternary ammonium salts) and insect repellent textile finishes (i.e. N‑N‑diethyl‑m‑toluamide, permethrin, cypermethrin, pyrethrum, picaridin, bioallethrin, citriodiol and essential oils) have been presented. Finally, the review is wrapped up with major research gaps/challenges, concluding remarks, and future opportunities in this area of research.

Bioprocess optimization of laccase production through solid substrate fermentation using Perenniporia tephropora-L168 and its application in bioremediation of triaryl-methane dye

Laccases are multi copper oxidases that can oxidize both phenolic and nonphenolic lignin related compounds. Consequently, there has been continuous demand for laccases for the oxidative degradation of phenolic dyes in effluents. In view of this, the present work was focused on laccase production by solid substrate fermentation using a newly isolated fungus Perenniporia tephropora-L168. To intensify the laccase production, the process parameters pH, nitrogen, inducer, and substrate: water ratio were optimized by using statistical model. A set of optimal conditions noted were pH 3, nitrogen 0.001 g/L; inducer 0.5% and substrate: water ratio (1:10), which yielded laccase 1,160 U/g. The crude laccase exhibited noteworthy potential to degrade a triaryl-methane dye especially Malachite green. Also, during bioremediation studies, the statistical process optimization could achieve 81% decolourization within 180 min. The laccase treatment brought chemical transformation in malachite green as evident from UV-Visible spectra, FTIR, HPLC while toxicity against bacteria and fungi was also reduced. During phytotoxicity study, effect of treated and untreated dye on germination of seed was analyzed. Interestingly, the germination index for Vigna aconitifolia and Vigna radiata was increased by two and fourfold, respectively. Overall, this work demonstrates optimized production of laccase using Perenniporia tephropora-L168 and its efficient bioremediation potential for triaryl-methane dye.

Sustainable bioconversion of food waste into high-value products by immobilized enzymes to meet bio-economy challenges and opportunities - A review

Over the past few years, food waste has intensified much attention from the local public, national and international organizations as well as a wider household territory due to increasing environmental, social and economic concerns, climate change and scarcity of fossil fuel resources. On one aspect, food-processing waste represents a substantial ecological burden. On the other hand, these waste streams are rich in carbohydrates, proteins, and lipids, thus hold significant potential for biotransformation into an array of high-value compounds. Indeed, the high sugar, protein, and fat content render food waste streams as attractive feedstocks for enzymatic valorization given the plentiful volumes generated annually. Enzymes as industrial biocatalysts offer unique advantages over traditional chemical processes with regard to eco-sustainability, and process efficiency. Herein, an effort has been made to delineate immobilized enzyme-driven valorization of food waste streams into marketable products such as biofuels, bioactive compounds, biodegradable plastics, prebiotics, sweeteners, rare sugars, surfactants, etc. Current challenges and prospects are also highlighted with respect to the development of industrially adaptable biocatalytic systems to achieve the ultimate objectives of sustainable manufacturing combined with minimum waste generation. Applications-based strategies to enzyme immobilization are imperative to design cost-efficient and sustainable industrially applicable biocatalysts. With a deeper apprehension of support material influences, and analyzing the extreme environment, enzymes might have significant potential in improving the overall sustainability of food processing.

Environmental perspectives of interfacially active and magnetically recoverable composite materials - A review

Aquatic ecosystem contaminated with toxic pollutants and heavy metals due to the rapid growth of industrialization has become a top-priority global concern exhibiting highly adverse effects on human health and the environment. Many treatment techniques have been envisioned for the removal of these toxic contaminants from the aqueous environment. Among these techniques, magnetic separation has attracted burgeoning research attention owing to its simplicity, eco-friendly nature, large surface area, electron mobility, and excellent performance for removing water contaminants. In particular, interfacial active nanoparticles and nanocomposites with unique structures and magnetic properties are considered as ideal provides candidates in material science for next-generation water treatment. This review gives an insight into current research activities associated with the synthesis strategies and applications of interfacially active and magnetically responsive nanomaterials and nanocomposites for sustainable purification processes. In the first half, various synthesis routes for magnetic iron oxide nanoparticles development and the corresponding formation mechanism are summarized. In the second half, we reviewed the magnetic and wettability properties of interfacially active and magnetically responsive nanocomposites and their environmental applications including oil-water separation, removal of hazardous dye-based pollutants and potentially toxic heavy metals. Finally, the review is wrapped up with major concluding remarks and future perspectives of these magnetic nanoscale composite materials for sustainable wastewater remediation.

Naturally-derived biopolymers: Potential platforms for enzyme immobilization

Naturally-derived biopolymers such as alginate, chitosan, cellulose, agarose, guar gum/guaran, agar, carrageenan, gelatin, dextran, xanthan, and pectins, etc. have appealed significant attention over the past several years owing to their natural abundance and availability all over the years, around the globe. In addition, their versatile properties such as non-toxicity, biocompatibility, biodegradability, flexibility, renewability, and the availability of numerous reactive sites offer significant functionalities with multipurpose applications. At present, intensive research efforts have been focused on engineering enzymes using natural biopolymers as novel support/composite materials for diverse applications in biomedical, environmental, pharmaceutical, food and biofuel/energy sectors. Immobilization appears as a straightforward and promising approach to developing biocatalysts with improved catalytic properties as compared to their free counterparts. Biopolymers-assisted enzymes are more stable, robust, and recoverable than that of free forms, and can be employed for continuous biocatalytic reactions. The present review highlights the recent developments and use of biopolymers and their advanced composites as support carriers for the immobilization of a variety of different enzymes to develop biocatalysts with desired catalytic activity and stability characteristics for emerging applications.

Immobilized bacterial biosensor for rapid and effective monitoring of acute toxicity in water

The use of biosensors by using microorganisms such as bacteria have short life cycles and provide other advantages. One colorimetric biosensor technique that has been developed is the use of a biosensor utilizing the incorporation of Prussian blue formation reactions mediated by E. coli bioreactors with ferricyanide. Immobilization is a method that allows the bacteria can be used for long-term without reducing its ability as bioreceptor. This study aimed to develop a novel and rapid immobilized bacterial biosensor for the detection of toxic compound in water and to evaluate their analytical performances. Immobilization of E. coli performed by trapping method using alginate material support. The bacterial suspension was mixed with sodium alginate (1:1 v/v), and the mixture was continuously dropped in CaCl₂ solution to be a form of beads. The beads were used as bioreceptor to detect toxicants regarding cadmium, arsenic, mercury, chromium and lead solutions with Prussian blue as a colorimetric indicator. The linearity and sensitivity of detection of beads to the toxicants were tested, the stability of repeated use and storage were evaluated as well. The results showed that E. coli could be immobilized using alginate with response value was correlated with toxic concentration. The developed biosensor was more stable when used repeatedly and could be stored in a long time. The immobilization of E. coli in calcium alginate bead was successfully performed as a biosensor system for monitoring acute toxicity in water.

Emerging contaminants of high concern and their enzyme-assisted biodegradation - A review

The widespread occurrence and adverse environmental and health-related impacts of various types of emerging contaminants (ECs) have become an issue of high concern. With ever increasing scientific knowledge, socio-economic awareness, health-related problems and ecological apprehensions, people are more concerned about the widespread ECs, around the globe. Among ECs, biologically active compounds from pharmaceutical, cosmeceutical, biomedical, personal care products (PPCPs), endocrine-disrupting chemicals (EDCs), and flame-retardants are of paramount concern. The presence and persistence of ECs in water bodies are of continued and burning interest, worldwide. Various types of ECs are being discharged knowingly/unknowingly with/without partial treatments into the aquatic environments that pose serious health issues and affects the entire living ecosystem. So far, various approaches have been developed for ECs degradation and removal to diminish their adverse impact. Many previous and/or ongoing studies have focused on contaminants degradation and efficient removal via numerous treatment strategies, i.e. (1) physical, (2) chemical and (3) biological. However, the experimental evidence is lacking to enable specific predictions about ECs mechanistic degradation and removal fate across various in-practice systems. In this context, the deployment oxidoreductases such as peroxidases (lignin peroxidases, manganese-dependent peroxidases, and horseradish peroxidase), aromatic dioxygenases, various oxygenases, laccases, and tyrosinases have received considerable research attention. Immobilization is highlighted as a promising approach to improve enzyme catalytic performance and stabilization, as well as, to protect the three-dimensional structure of the enzyme against the undesirable consequences of harsh reaction environment. This work overviews the current and state-of-the-art critical aspect related to hazardous pollutants at large and ECs in particular by the immobilized oxidoreductase enzymes. The first part of the review focuses on the occurrence, physiochemical behavior, potent sources and significant routes of ECs. Following that, environmentally-related adverse impacts and health-related issues of ECs are discussed in the second part. In the third part, biodegradation and removal strategies with a comparative overview of several conventional vs. non-conventional methods are presented briefly. The fourth part majorly focuses on operational modes of different oxidoreductase enzyme-based biocatalytic processes for the biodegradation and biotransformation of a wide array of harmful environmental contaminants. Finally, the left behind research gaps, concluding remarks as well as future trends and recommendations in the use of carrier-immobilized oxidoreductases for environmental perspective are also discussed.

Environmentally-related contaminants of high concern: Potential sources and analytical modalities for detection, quantification, and treatment

In recent years, emerging contaminants (ECs) of high concern are broadly distributed throughout the environmental matrices because of various industrial practices and anthropogenic inputs, i.e., human-made activities. With ever increasing scientific knowledge, technological advancement, socio-economic awareness, people are now more concern about the widespread distribution of environmentally related ECs of high concern. As, ECs possess serious ecological threats and potential risks to human health and aquatic life, even at minor concentrations. The controlled or uncontrolled discharge and long-term persistence of ECs that includes micro-pollutants, endocrine disruptors (EDs), pesticides, pharmaceuticals, hormones, toxins, and industrially-related synthetic dyes and dyes-containing hazardous pollutants, etc. pose a significant challenge to policy regulators, engineers, and scientific community. The conventional treatment technologies are proved ineffective for the complete elimination and removal of an array of contaminants of emerging environmental concern in various biological and environmental samples. In order to overcome the aforementioned ecological threats, tremendous research efforts have been made to boost the efficiency of remediation techniques or develop new modalities to detect, quantify and treat the samples efficiently. The boom in biotechnology and environmental engineering offers potential opportunities to develop advanced and innovative remediation techniques in the field of water treatment. This review discusses the environmental and health hazards associated with a widespread distribution of micro-pollutants, pesticides, pharmaceuticals, hormones, and industrially-related synthetic dyes and dyes-containing hazardous pollutants, etc. in the water bodies, i.e., surface water, groundwater, and industrial wastewater streams. Life-cycle distribution of emerging (micro)-pollutants with suitable examples from various industrial sources viewpoints is also discussed. The later part of the review focuses on innovative and cost-effective remediation (removal) approaches from phase-changing treatment technologies for these ECs of high concern.

"Smart" chemistry and its application in peroxidase immobilization using different support materials

In the past few decades, the enzyme immobilization technology has been exploited a lot and thus became a matter of rational design. Immobilization is an alternative approach to bio-catalysis with the added benefits, adaptability to automation and high-throughput applications. Immobilization-based approaches represent simple but effective routes for engineering enzyme catalysts with higher activities than wild-type or pristine counterparts. From the chemistry viewpoint, the concept of stabilization via manipulation of functional entities, the enzyme surfaces have been an important driving force for immobilizing purposes. In addition, the unique physiochemical and structural functionalities of pristine or engineered cues, or insoluble support matrices (carrier) such as mean particle diameter, swelling behavior, mechanical strength, and compression behavior are of supreme interest and importance for the performance of the immobilized systems. Immobilization of peroxidases into/onto insoluble support matrices is advantageous for practical applications due to convenience in handling, ease separation of enzymes from a reaction mixture and the reusability. A plethora of literature is available explaining individual immobilization system. However, current literature lacks the chemistry viewpoint of immobilization. This review work presents state-of-the-art "Smart" chemistry of immobilization and novel potentialities of several materials-based cues with different geometries including microspheres, hydrogels and polymeric membranes, nanoparticles, nanofibers, composite and hybrid or blended support materials. The involvement of various functional groups including amino, thiol, carboxylic, hydroxyl, and epoxy groups via "click" chemistry, amine chemistry, thiol chemistry, carboxyl chemistry, and epoxy chemistry over the protein surfaces is discussed.

Removal of methylene blue dye from aqueous solution using immobilized Agrobacterium fabrum biomass along with iron oxide nanoparticles as biosorbent

A nano-biosorbent for the removal of methylene blue (MB) was prepared by encapsulating iron oxide nanoparticles (NPs) and Agrobacterium fabrum strain SLAJ731, in calcium alginate. The prepared biosorbent was optimized for the maximum adsorption capacity at pH 11, 160 rpm, and 25 °C. Adsorption kinetics was examined using pseudo-first-order, pseudo-second-order, and intra-particle diffusion (IPD) models. The kinetic data agreed to pseudo-second-order model indicating chemisorption of MB, which was also explained by FTIR analysis. The adsorption rate constant (k₂) decreased and initial adsorption rate (h, mg g^-1 min^-1) increased, with an increase in initial dye concentration. The dye adsorption process included both IPD and surface adsorption, where IPD was found to be a rate-limiting step after 60 min of adsorption. The adsorption capacity was found to be 91 mg g^-1 at 200 mg L^-1 dye concentration. Adsorption data fitted well to Freundlich isotherm; however, it did not fit to Langmuir isotherm, indicating adsorbent surfaces were not completely saturated (monolayer formed) up to the concentration of 200 mg L^-1 of MB. Thermodynamic studies proposed that the adsorption process was spontaneous and exothermic in nature. Biosorbent showed no significant decrease in adsorption capacity even after four consecutive cycles. The present study demonstrated dead biomass along with NPs as a potential biosorbent for the treatment of toxic industrial effluents.

Developments in support materials for immobilization of oxidoreductases: A comprehensive review

Bioremediation, a biologically mediated transformation or degradation of persistent chemicals into nonhazardous or less-hazardous substances, has been recognized as a key strategy to control levels of pollutants in water and soils. The use of enzymes, notably oxidoreductases such as laccases, tyrosinases, various oxygenases, aromatic dioxygenases, and different peroxidases (all of EC class 1) is receiving significant research attention in this regard. It should be stated that immobilization is emphasized as a powerful tool for enhancement of enzyme activity and stability as well as for protection of the enzyme proteins against negative effects of harsh reaction conditions. As proper selection of support materials for immobilization and their performance is overlooked when it comes to comparing performance of immobilized enzyme in academic studies, this review summarizes the current state of knowledge regarding the materials used for enzyme immobilization of these oxidoreductase enzymes for environmental applications. In the presented study, thorough physicochemical characteristics of the support materials was presented. Moreover, various types of reactions and notably operational modes of enzymatic processes for biodegradation of harmful pollutants are summarized, and future trends in use of immobilized oxidoreductases for environmental applications are discussed. Our goal is to provide an improved foundation on which new technological advancements can be made to achieve efficient enzyme-assisted bioremediation.