Level-wise differences in in vivo lateral bending moment are associated with microstructural alterations in bovine caudal intervertebral discs

Three-dimensional fiber patterning in the annulus fibrosus can be derived from vertebral endplate topography

Introduction

The annulus fibrosus (AF) of the Intervertebral disc (IVD) is composed of concentric lamellae of helically wound collagen fibers. Understanding the spatial variation of collagen fiber orientations in these lamellae, and the resulting material anisotropy, is crucial to predicting the mechanical behavior of the complete IVD.

Methods

This study builds on a prior model predicated on path-independent displacement of fiber endpoints during vertebral body growth to predict a complete, three-dimensional annulus fibrosus fiber network from a small number of subject-independent input parameters and vertebral endplate topographies obtained from clinical imaging. To evaluate the model, it was first fit to mid-plane fiber orientations obtained using polarized light microscopy in a population of bovine caudal discs for which computed tomography images vertebral endplates were also available. Additionally, the model was used to predict the trajectories based on human lumbar disc geometries and results were compared to previously reported data. Finally, the model was employed to investigate potential disc-related variations in fiber angle distributions.

Results

The model was able to accurately predict experimentally measured fiber distributions in both bovine and human discs using only endplate topography and three input parameters. Critically, the model recapitulated previously observed asymmetry between the inclinations of right- and left-handed fibers in the posterolateral aspect of the human AF. Level to level variation of disc height and aspect ratio in the human lumbar spine was predicted to affect absolute values of fiber inclination, but not this asymmetry.

Conclusion

Taken together these results suggest that patient-specific distributions of AF fiber orientation may be readily incorporated into computational models of the spine using only disc geometry and a small number of subject-independent parameters.

Establishing a through-puncture model for assessing post-injection leakage in the intervertebral disc

PURPOSE

Needle injection through the outer annulus fibrosus of the intervertebral disc (IVD) is the most practical approach for delivery of therapeutic agents, which have been shown to potentially leak following needle retraction. The goal of this work was to establish a protocol for quantifying post-injection leakage and test its sensitivity to factors believed to affect needle track geometry.

METHODS

A through-puncture defect procedure, followed by controlled injection, was performed on bovine caudal IVDs. Sensitivity to needle size was tested by injection of saline into unconstrained discs with either a 30G, 26G, or 21G hypodermic needle. Sensitivity to axial load was tested by repeated injection via a 26G needle with either no constraint, fixed height, or 10% axial compressive strain. Sensitivity to flexion was tested by applying combined 0.2 MPa compression and 15° of flexion following injection of 5% of disc volume.

RESULTS

Needle diameter significantly affected maximum volume prior to leakage, ranging from 34.6 ± 31.9 µL when using 21G to 115.6 ± 23.6 µL when using 30G. While all unloaded discs leaked, axial compression decreased the incidence of leakage events by 50-100% depending on load history. Forward flexion resulted in a 22% incidence of leakage.

CONCLUSION

Fluid injected into IVDs is at significant risk of leakage following needle retraction. This risk depends on factors which alter the geometry of the needle track, including needle size, pinching due to axial compression, and stretching as a result of forward flexion.

Reflected cross-polarized light microscopy as a method for measuring collagen fiber crimp in musculoskeletal tissues

Many musculoskeletal tissues are composed primarily of type I collagen, which takes on a periodic crimp morphology that allows large tensile strains in the tissue. The spatial period of collagen fiber crimp may be used to infer internal strains in a tissue and is typically measured using transmitted cross-polarized light imaging of thin slices. However, slicing may induce specimen distortion and precludes mechanical loading of the specimen during imaging. We hypothesized that reflected cross-polarized light imaging of thick tissue explants would yield crimp period measurements comparable to those obtained from transmitted light imaging of thin slices. We further hypothesized that these measurements would be sensitive to applied uniaxial strain in the fiber direction. These hypotheses were tested by imaging both intervertebral disc outer annulus fibrosus and medial collateral ligament tissue specimens. We found that both transmitted and reflected light yielded similar crimp period measurements for intervertebral disc tissue, with an overall average of 43.5 ± 11.5 μm. Reflected light yielded a significantly higher crimp period with lower variance than transmission through thin specimens (54.1 ± 10.6 μm versus 50.4 ± 16.0 μm) in the ligament. Upon application of axial tension, crimp periods in both fibers increased at a rate of approximately three times the applied strain (with 3.17% applied strain yielding a 9.64 ± 4.4% increase in crimp period in the disc and an 11.7 ± 3.7% increase in the ligament), indicating significant fibril sliding. In support of our hypotheses, these findings suggest that reflected cross-polarized light is a suitable method for measuring collagen fiber crimp in musculoskeletal tissues, both statically and under tension.