pH- and Photoresponsive Liquid Plasticine

Liquid marbles (LMs) can be prepared by adsorption of hydrophobic particles at the air-liquid interface of a water droplet. LMs have been studied for their application as microreaction vessels. However, their opaqueness poses challenges for internal observation. Liquid plasticines (LPs), akin to LMs, can be prepared by the adsorption of hydrophobic particles with a diameter of 50 nm or less, at the air-liquid interface of a water droplet. Unlike LMs, LPs are transparent, allowing for internal observation, thus presenting promising applications as reactors and culture vessels on a microliter scale. In this study, the surface of silica particles, approximately 20 nm in diameter, was rendered hydrophobic to prepare hydrophobic silica particles (SD0). A small amount of poly(2-(diisopropylamino)ethyl methacrylate) (PDPA) was then grafted onto the surface of SD0, yielding SD1. SD0 particles exhibited consistent hydrophobicity irrespective of the environmental pH atmosphere. Under acidic conditions, SD1 became hydrophilic due to the protonation of pendant tertiary amines in the grafted PDPA chains. However, SD1 alone was unsuitable for LP preparation due to its high surface wettability regardless of atmospheric pH, attributable to the presence of PDPA-grafted chains. Therefore, to prepare pH-responsive LP, SD1 and SD0 were mixed (SD1/SD0 = 3/7). Upon exposure to HCl gas, these LPs ruptured, with the leaked water from the LPs being absorbed by adjacent paper. Moreover, clear LPs, prepared using an aqueous solution containing a water-soluble photoacid generator (PAG), disintegrated upon exposure to light as PAG generated acid, leading to LP breakdown. In summary, pH-responsive LPs, capable of disintegration under acidic conditions and upon light irradiation, were successfully prepared in this study.

Droplet-Impact Driven Formation of Ultralow Volume Liquid Marbles with Enhanced Mechanical Stability and Sensing Ability

Liquid marbles (LMs), droplets encapsulated with micro/nanoparticles, have attracted significant attention owing to their potential applications in various fields, ranging from microbioreactors to sensors. The volume of the LMs is a key parameter determining their mechanical stability and gas sensing ability. It is ideal to work with small volumes because of their better mechanical stability and gas sensing power compared to the larger LMs. Though many methods exist for producing LMs in the volume range above 2 μL, no reliable method exists to prepare fully coated submicroliter LMs with tunable volume. The situation becomes even more difficult when one attempts to produce tiny Janus Liquid Marbles (JLMs). This paper presents a simple, single-step, and efficient strategy for obtaining both the pristine LMs and JLMs in the volume range 200 nL to 18 μL. The core idea relies on the impact of a liquid drop on a particle bed at a Weber number of ∼55 to produce two daughter droplets and to convert these droplets into LMs/JLMs. The whole process takes only a few tens of milliseconds (∼50 ms). We have rendered the experimental schemes so that both the JLMs and pristine LMs can be produced in a single step, with control over their volume. The mechanical stability analysis of the prepared marbles indicates that 200 nL is 5 times more stable than 10 μL of LMs. The 0.72 μL LMs prepared with a 0.5 v/v % phenolphthalein indicator solution showed 3 times faster response time to ammonia gas sensing than 10 μL of LMs. The results presented in this work open up a new route for the rapid and reliable production of both multilayered LMs and JLMs with tunable volume in a wide range (200 nL to 18 μL).

Liquid Marbles under Electric Fields: New Capabilities for Non-wetting Droplet Manipulation and Beyond

The study of liquid marbles (LMs) composed of stabilizing liquid droplets with solid particles in a gaseous environment has matured into an established area in surface and colloid science. The minimized "solid-liquid-air" triphase interface enables LMs to drastically reduce adhesion to a solid substrate, making them unique non-wetting droplets transportable with limited energy. The small volume, enclosed environment, and simple preparation render them suitable microreactors in industrial applications and processes such as cell culture, material synthesis, and blood coagulation. Extensive application contexts request precise and highly efficient manipulations of these non-wetting droplets. Many external fields, including magnetic, acoustic, photothermal, and pH, have emerged to prepare, deform, actuate, coalesce, mix, and disrupt these non-wetting droplets. Electric fields are rising among these external stimuli as an efficient source for manipulating the LMs with high controllability and a significant ability to contribute further to proposed applications. This Feature Article attempts to outline the recent developments related to LMs with the aid of electric fields. The effects of electric fields on the preparation and manipulation of LMs with intricate interfacial processes are discussed in detail. We highlight a wealth of novel electric field-involved LM-based applications and beyond while also envisaging the challenges, opportunities, and new directions for future development in this emerging research area.

Liquid marbles, floating droplets: preparations, properties, operations and applications

Liquid marbles (LMs) are non-wettable droplets formed with a coating of hydrophobic particles. They can move easily across either solid or liquid surfaces since the hydrophobic particles protect the internal liquid from contacting the substrate. In recent years, mainly due to their simple preparation, abundant materials, non-wetting/non-adhesive properties, elasticities and stabilities, LMs have been applied in many fields such as microfluidics, sensors and biological incubators. In this review, the recent advances in the preparation, physical properties and applications of liquid marbles, especially operations and floating abilities, are summarized. Moreover, the challenges to achieve uniformity, slow volatilization and stronger stability are pointed out. Various applications generated by LMs' structural characteristics are also expected.

pH-Responsive Liquid Marbles Based on Dihydroxystearic Acid

Herein, we report pH-responsive liquid marbles stabilized by 9,10-dihydroxystearic acid (DHSA). The particle morphology and the pH-responsive behavior of the liquid marbles were investigated. The rolling time during the preparation of liquid marbles has a great influence on the thickness of powder adsorption and the stability of the marbles. Compared with the liquid marbles stabilized by other fatty acids (e.g., stearic acid and docosoic acid), the liquid marbles prepared by DHSA have a much higher mechanical robustness. The increase in the number of hydroxyl groups on the carbon chain of fatty acids improves the mechanical robustness of the liquid marbles. Such liquid marbles immediately disintegrated on the surface of an alkaline solution or after exposure to NH₃ gas, which extends their applications in the NH₃ sensor and chemical reactions.

Liquid marble-based digital microfluidics - fundamentals and applications

Liquid marbles are droplets with volume typically on the order of microliters coated with hydrophobic powder. Their versatility, ease of use and low cost make liquid marbles an attractive platform for digital microfluidics. This paper provides the state of the art of discoveries in the physics of liquid marbles and their practical applications. The paper first discusses the fundamental properties of liquid marbles, followed by the summary of different techniques for the synthesis of liquid marbles. Next, manipulation techniques for handling liquid marbles are discussed. Applications of liquid marbles are categorised according to their use as chemical and biological reactors. The paper concludes with perspectives on the future development of liquid marble-based digital microfluidics.

Simple and Continuous Fabrication of Janus Liquid Marbles with Tunable Particle Coverage Based on Controlled Droplet Impact

Liquid marbles are gaining increased attention because of their added advantages such as low evaporation rates, less friction, and ease of manipulation over the pristine liquid drop. Their functionalities could be further enhanced by incorporating different types of particles (size, hydrophobicity, chemical properties, etc.), commonly called Janus liquid marbles (JLMs). However, their fabrication process remains a challenge, especially when we require continuous production. Here, we present a simple and fast approach for the fabrication of JLMs covered with nano- and microparticles in an additive-free environment based on the controlled impact of a water drop over the particle beds. The fabrication process involves collection of polyvinylidene difluoride particles (PVDF, particle type 1) by a water drop followed by its impact over an uncompressed bed of black toner particles (BTP, particle type 2). The whole process takes a time of approximately 30 ms only. The drop impact and the condition of the JLM formation were explained based on the Weber number (We) and maximum spread (β_m) analysis. A theoretical model based on the energy balance analysis is performed to calculate the maximum spreading (β_m), and the experimental and theoretical analyses are found to be in good agreement. Tunability in particle coverage is demonstrated by varying the droplet volume in the range of 5-15 μL. We further extend this strategy for the fast and continuous production of nearly identical JLMs, which could enhance the capabilities of open-surface microfluidic applications.

Manufacture and properties of composite liquid marbles

HYPOTHESIS

Liquid marbles are non-stick droplets coated with colloidal usually hydrophobic particles. We suggest that "composite" liquid marbles, i.e. bi-liquid droplets, may be prepared with water droplets coated by a thin silicone oil layer containing hydrophobic, colloidal particles.

EXPERIMENTS

The process enabling manufacturing water marbles coated with silicone oil containing fumed fluorosilica particles is reported. The marbles remained stable when placed on solid and liquid supports. Bouncing and coalescence of the composite marbles was explored.

FINDINGS

Non-coalescence prolonged (ca. 20 min) jumping of composite marbles above a vibrating water bath was observed. Composite marbles withstand coalescence better than colloidal particle-stabilized liquid marbles. The effective surface tension of the composite marbles is markedly lower than that of water marbles coated with fumed fluorosilica particles. The coefficient of restitution of the composite marbles bouncing on a hydrophobic solid substrate is lower than that established for water marbles. This observation is related to the viscous dissipation occurring within the silicone layer making up the composite marbles.

CO2-Gas-Responsive Liquid Marble

Liquid marbles were prepared using a water droplet and nonprotonated hydrophobic poly(2-N,N-diisopropylaminoethyl methacrylate) (PDiPAEMA) powder. Although the nonprotonated PDiPAEMA was hydrophobic, PDiPAEMA became hydrophilic because of the protonation of the pendant tertiary amino groups under acidic conditions. Therefore, liquid marbles stabilized with PDiPAEMA powder could float on a neutral to basic water surface, but they immediately disintegrated on an acidic water surface. Furthermore, the liquid marbles floating on the water surface disintegrated in response to CO₂ gas because the water became acidic as a result of carbonic acid formation.

Mechanical robustness of monolayer nanoparticle-covered liquid marbles

Powder-derived liquid marbles (LMs) are versatile nonwetting systems but are confronted with many limitations in application, as their surface particles are usually large and agglomerated. Recently, sol-gel film-derived LMs have come on the scene that are termed monolayer nanoparticle-covered (mNPc) LMs based on their unique characteristics, revealing great application potential but also generating many questions. Here, mechanical robustness, a very important yet to be addressed property, of mNPc LMs was systematically studied. Rolling, pendant contact, and compression experiments were designed using bare and coated glasses with water contact angles (WCAs) ranging from 23° to 157°. With rupture as a quality criteria, the mechanical robustness of mNPc LMs enhanced with the hydrophobicity of solid surfaces that exerted pressure on them, but maintained much weaker than typical powder LMs until the solid surface was superhydrophobic. In particular, when contacting hydrophilic surfaces of WCAs ≤53°, an mNPc LM did not have the capacity for nonwetting and ruptured immediately, even if the pressure approached zero. This was distinct from powder LMs and indicated that a particle shell as thin as ∼20 nm could not prevent intermolecular attractions between the internal liquid and external solid surface. An interface scenario consisting of solid surface microroughness was proposed to address this issue. On the other hand, mNPc LMs remained unruptured on superhydrophobic surfaces but presented degraded elasticity under extreme compression. Uncovering these properties could be of much help for developments of mNPc LMs and their counterparts, the mNPc liquid plasticines.

Liquid marbles and liquid plasticines with nanoparticle monolayers

Liquid marbles, as particle-covered macroscopic liquid drops in an air environment, have exhibited great value as self-standing liquid containers in various areas, such as material synthesis, chemical analysis, and cell culture. However, conventional liquid marbles obtained by the rolling-on-powder-bed method usually feature micron-sized or larger particle agglomerates, which harm marble transparency and fine control of marble shape and thus results in considerable limitations for marble applications. Recently, monolayer nanoparticle (NP) coverage has been achieved using a sol-gel film instead of a powder as the particle source. The NP monolayer structure can not only result in highly transparent liquid marbles with very smooth and symmetrical profiles, but can also lead to liquid entities with arbitrarily designable shapes, as called liquid plasticines. Monolayer NP-covered (mNPc) liquid marbles and plasticines have generated important results in both fundamental and practical applications, as ideal physical models or advanced self-standing containers, showing great advantages in some conditions over conventional powder-derived liquid marbles. In this review, the preparations and current applications of the two mNPc systems are summarized and perspectives on their advantages, unclear issues, and application extension are provided.

Rod-shaped liquid plasticine for gas diffusion detection

A rod-shaped liquid plasticine was produced here, which was then shown to serve as a versatile gas detector based on a coloration mechanism. It not only indicated gas existence but also visually revealed the gas frontier positions, which allowed the calculation of diffusion speeds and gas concentrations. This study demonstrated the feasibility of multifunctional applications in a liquid plasticine using its shape and optical advantages.

A capillary rise method for studying the effective surface tension of monolayer nanoparticle-covered liquid marbles

The liquid marble covered with a xerogel-derived nanoparticle monolayer is emerging as a simple and ideal physical model for fundamental study. In this work, the effective surface tension, γeff, of this kind of water marble was studied by employing an optimized capillary rise method. This method is distinctive as it can reveal γeff at a specific point rather than the average γeff over the entire marble. γeff at the maximum lateral diameter position was investigated with particle coverage varying from 100% to 10%, showing a quite slow increasing trend from ∼64 to 72 mN m-1. The delay in the evolution of the γeff was attributed to the slow decline in the areal particle density on the side area of the marble. For comparative purposes, the maximum height method was also employed to determine γeff. The results of the two methods supported the position that a liquid marble's γeff depended on very specific conditions including the measurement method and all marble parameters.

pH-Responsive Particle-Liquid Aggregates-Electrostatic Formation Kinetics

Liquid-particle aggregates were formed electrostatically using pH-responsive poly[2-(diethylamino)ethyl methacrylate] (PDEA)-coated polystyrene particles. This novel non-contact electrostatic method has been used to assess the particle stimulus-responsive wettability in detail. Video footage and fractal analysis were used in conjunction with a two-stage model to characterize the kinetics of transfer of particles to a water droplet surface, and internalization of particles by the droplet. While no stable liquid marbles were formed, metastable marbles were manufactured, whose duration of stability depended strongly on drop pH. Both transfer and internalization were markedly faster for droplets at low pH, where the particles were expected to be hydrophilic, than at high pH where they were expected to be hydrophobic. Increasing the driving electrical potential produced greater transfer and internalization times. Possible reasons for this are discussed.

The Potential of Liquid Marbles for Biomedical Applications: A Critical Review

Liquid marbles (LM) are freestanding droplets covered by micro/nanoparticles with hydrophobic/hydrophilic properties, which can be manipulated as a soft solid. The phenomenon that generates these soft structures is regarded as a different method to generate a superhydrophobic behavior in the liquid/solid interface without modifying the surface. Several applications for the LM have been reported in very different fields, however the developments for biomedical applications are very recent. At first, the LM properties are reviewed, namely shell structure, LM shape, evaporation, floatability and robustness. The different strategies for LM manipulation are also described, which make use of magnetic, electrostatic and gravitational forces, ultraviolet and infrared radiation, and approaches that induce LM self-propulsion. Then, very distinctive applications for LM in the biomedical field are presented, namely for diagnostic assays, cell culture, drug screening and cryopreservation of mammalian cells. Finally, a critical outlook about the unexplored potential of LM for biomedical applications is presented, suggesting possible advances on this emergent scientific area.

Rationally Turning the Interface Activity of Mesoporous Silicas for Preparing Pickering Foam and "Dry Water"

We develop a novel protocol to prepare smart, gas/water interface-active, mesoporous silica particles. This protocol involves modification of highly mesoporous silicas with a mixture of hydrophobic octyl organosilane and hydrophilic triamine organosilane. Their structure and compositions are characterized by transmission electron microscopy (TEM), N₂ sorption, solid state NMR, X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectra (FT-IR), thermogravimetric analysis (TGA), and elemental analysis. It is demonstrated that our protocol enables the interface activity of mesoporous silica particles to be facilely tuned, so that the stable gas-water interfaces ranging from air bubbles dispersed in water (Pickering foam) and water droplets dispersed in air ("dry water") can be achieved, depending on the molar ratio of these two organosilanes. The "dry water" is not otherwise attainable for the analogous nonporous silica particles, indicting the uniqueness of the chosen mesoporous structures. Moreover, these particle-stabilized Pickering foams and "dry waters" can be disassembled in response to pH. Interestingly, it was found that aqueous potassium carbonate droplets stabilized by these interface-active mesoporous silica particles ("dry K₂CO₃-containing water") could automatically capture CO₂ from a simulated flue gas with enhanced adsorption rate and adsorption capacity when compared to the aqueous potassium carbonate bulk solution. This study not only supplies a novel type of efficient, smart, gas/water interface-active mesoporous silica particles but also demonstrates an innovative application of mesoporous materials in gas adsorption.

One-Step Synthesis of Hydrophobic Multicompartment Organosilica Microspheres with Highly Interconnected Macro-mesopores for the Stabilization of Liquid Marbles with Excellent Catalysis

The combination of an emulsion template with polymerization is a very convenient approach to the one-step realization of both simple control porous structures via a change in emulsion formulation and easy functionalization via the concomitant choice of an on-demand monomer. A major challenge of this approach is the inherent instability of the oil/water interface in emulsions, especially the occurrence of chemical reactions in oil or aqueous phases. This study reports the pioneering preparation of highly interconnected macro-mesopores and multicompartment (HIMC) vinyl organosilica microspheres with hydrophobicity by the one-step formation of W/O/W emulsions acting as a template. The emulsion system consists of acidified deionized water, a stabilizer, and vinyltriethoxysilane (VTEO) in which VTEO can be used to produce an organosilica skeleton of the resultant microsphere by a sol-gel process. The study demonstrated that the marvelous stability of W/O/W emulsions aids the formation of multicompartment organosilica microspheres with highly interconnected macro-mesopores by emulsion droplets rather than single-compartment (SC) microspheres. Meanwhile, the internal porous structure and surface morphology of as-prepared organosilica microspheres could be largely tuned by a simple variation of the pH value, the volume fraction of the water phase, and the stabilizer concentration in the initiating multiemulsions. Benefiting from such a well-orchestrated structure and the existence of numerous vinyl groups on the surface, HIMC organosilica microspheres exhibit very high hydrophobicity (with a water contact angle larger than 160°), which allows them to stabilize liquid marbles with excellent stability and high mechanical robustness. Because of its strong catalyst, Ag nanoparticles within HIMC organosilica microspheres enable Ag/HIMC-vinyl organosilica microsphere-based liquid marbles to be an efficient catalytic microreactor, realizing the complete degradation of MB to leuco methylene blue by NaBH₄ in 10 min. The result of this work could provide some guidance for the easy, low-cost, benign preparation of HIMC microspheres having the potential to be excellent supporter of metal nanoparticles or other functionalized compounds for applications in sensing, optoelectronics, and catalysis.

Liquid Marbles, Elastic Nonstick Droplets: From Minireactors to Self-Propulsion

Liquid marbles are nonstick droplets wrapped by micro- or nanometrically scaled colloidal particles, representing a platform for a variety of chemical, biological, and microfluidics applications. Liquid marbles demonstrate elastic properties and do not coalesce when bounced or pressed. The effective surface tension and Young modulus of liquid marbles are discussed. Physical sources of the elasticity of liquid marbles are considered. Liquids and powders used for the fabrication of liquid marbles are surveyed. This feature article reviews properties and applications of liquid marbles. Liquid marbles demonstrate potential as microreactors, microcontainers for growing micro-organisms and cells, and microfluidics devices. The Marangoni-flow-driven self-propulsion of marbles supported by liquids is addressed.

Near-Infrared-Sensitive Materials Based on Upconverting Nanoparticles

The near-infrared (NIR) region of the spectrum is called the "therapeutic window" because NIR light can penetrate deeply into tissue. Therefore, NIR-sensitive materials are attractive for biomedical applications. Recently, upconverting nanoparticles (UCNPs) were used to construct NIR-sensitive materials. UCNPs convert NIR light to UV or visible light, which can trigger photoreactions of photosensitive materials. Here, how to use UCNPs to construct NIR-sensitive materials is introduced, applications of NIR-sensitive materials with a focus on biomedical applications are highlighted, and the associated challenges are discussed.

Liquid marble and water droplet interactions and stability

The interactions between two individual water droplets were investigated in air using a combination of coalescence rig and high speed video camera. This combination allows the visualization of droplet coalescence dynamics with millisecond resolution which provides information on droplet stability. Bare water droplets coalesced rapidly upon contact, while droplet stability was achieved by coating the droplets with polystyrene particles carrying pH-responsive poly[2-(diethylamino)ethyl methacrylate] hairs (PDEA-PS particles) to form liquid marbles. The asymmetric interaction of a water droplet (pH 3 or 10) armoured with the PDEA-PS particles (liquid marble) with a bare droplet at pH 3 exhibited intermediate stability with coalescence observed following an induction time. The induction time was longer for the pH 10 liquid marble, where the PDEA-PS particles have a hydrophobic surface, than in the case of a pH 3 liquid marble, where the PDEA-PS particles have a hydrophilic surface. Furthermore, film formation of PDEA-PS particles on the liquid marble surface with toluene vapour confirmed capsule formation which prevented coalescence with the neighbouring water droplet instead wetting the capsule upon contact within 3 milliseconds. This study illuminates the stability of individual particle-stabilized droplets and has potential impact on processes and formulations which involve their interaction.

Liquid marbles: topical context within soft matter and recent progress

The study of particle stabilized interfaces has a long history in terms of emulsions, foams and related dry powders. The same underlying interfacial energy principles also allow hydrophobic particles to encapsulate individual droplets into a stable form as individual macroscopic objects, which have recently been called "Liquid Marbles". Here we discuss conceptual similarities to superhydrophobic surfaces, capillary origami, slippery liquids-infused porous surfaces (SLIPS) and Leidenfrost droplets. We provide a review of recent progress on liquid marbles, since our earlier Emerging Area article (Soft Matter, 2011, 7, 5473-5481), and speculate on possible future directions from new liquid-infused liquid marbles to microarray applications. We highlight a range of properties of liquid marbles and describe applications including detecting changes in physical properties (e.g. pH, UV, NIR, temperature), use for gas sensing, synthesis of compounds/composites, blood typing and cell culture.

Liquid marbles prepared from pH-responsive self-assembled micelles

In this study, we report the assembly of amphiphilic polymeric micelles at the liquid/air interface to prepare liquid marbles for the first time. The polymeric micelles were synthesized from the self-assembly of a fluoropolymer, poly(styrene-co-acrylic acid-co-2,2,3,4,4,4-hexafluorobutyl methacrylate), in a selective solvent. The particle size, morphology and chemical composition of the micelles were determined by dynamic light scattering (DLS), transmission electron microscopy, scanning electron microscopy and X-ray photoelectron spectroscopy. DLS and aqueous electrophoresis revealed the pH-responsiveness of the micelles in aqueous dispersion. Liquid marbles with water volumes varying from 10 μL to 1 mL were formed by rolling water droplets on the micelle powder bed. The increase in water volume led to the shape transition of the liquid marbles from quasi-spherical to a puddle-like shape because of gravity. Fluorescence microscopy was used to observe the morphology of the formed liquid marbles, which confirmed that the micelles were adsorbed at the interface of water and air. The effective surface tension of the liquid marbles decreased with the increasing concentration of NaOH, which was added to the interior water phase. This agreed with the results of droplet roller experiments: the mechanical integrity of the liquid marbles prepared from alkaline solution (pH 10) was relatively poorer than those prepared from acidic solution (pH 2). Moreover, these liquid marbles coated with micelles showed pH-responsiveness when transferred onto the surfaces of aqueous solutions with different pH values. The liquid marbles were relatively stable on the acidic solution, whereas they burst immediately on the alkaline solution with a pH of 10. In addition, apart from water, Gellan gum solution and glycerol could be also successfully encapsulated by the fluorinated micelles to form stable liquid marbles.

Photoresponsive liquid marbles and dry water

Stimuli-responsive liquid marbles for controlled release typically rely on organic moieties that require lengthy syntheses. We report herein a facile, one-step synthesis of hydrophobic and oleophobic TiO2 nanoparticles that display photoresponsive wettability. Water liquid marbles stabilized by these photoresponsive TiO2 particles were found to be stable when shielded from ultraviolet (UV) radiation; however, they quickly collapsed after being irradiated with 302 nm UV light. Oil- and organic-solvent-based liquid marbles could also be fabricated using oleophobic TiO2 nanoparticles and show similar UV-induced collapse. Finally, we demonstrated the formation of the micronized form of water liquid marbles, also known as dry water, by homogenization of the TiO2 nanoparticles with water. The TiO2 dry water displayed a similar photoresponse, whereby the micronized liquid marbles collapsed after irradiation and the dry water turned from a free-flowing powder to a paste. Hence, by exploiting the photoresponsive wettability of TiO2, we fabricated liquid marbles and dry water that display photoresponse and studied the conditions required for their collapse.

Microcapsules fabricated from liquid marbles stabilized with latex particles

Millimeter- and centimeter-sized "liquid marbles" were readily prepared by rolling water droplets on a powder bed of dried submicrometer-sized polystyrene latex particles carrying poly[2-(diethylamino)ethyl methacrylate] hairs (PDEA-PS). Scanning electron microscopy studies indicated that flocs of the PDEA-PS particles were adsorbed at the surface of these water droplets, leading to stable spherical liquid marbles. The liquid marbles were deformed as a result of water evaporation to adopt a deflated spherical geometry, and the rate of water evaporation decreased with increasing atmospheric relative humidity. Conversely, liquid marbles formed using saturated aqueous LiCl solution led to atmospheric water absorption by the liquid marbles and a consequent mass increase. The liquid marbles can be transformed into polymeric capsules containing water by exposure to solvent vapor: the PDEA-PS particles were plasticized with the solvent vapor to form a polymer film at the air-water interface of the liquid marbles. The polymeric capsules with aqueous volumes of 250 μL or less kept their oblate ellipsoid/near spherical shape even after complete water evaporation, which confirmed that a rigid polymeric capsule was successfully formed. Both the rate of water evaporation from the pure water liquid marbles and the rate of water adsorption into the aqueous LiCl liquid marbles were reduced with an increase of solvent vapor treatment time. This suggests that the number and size of pores within the polymer particles/flocs on the liquid marble surface decreased due to film formation during exposure to organic solvent vapor. In addition, organic-inorganic composite capsules and colloidal crystal capsules were fabricated from liquid marbles containing aqueous SiO2 dispersions.