A preliminary study to determine the diagnostic reference level using dose-area product for limited-area cone beam CT

Proposed Diagnostic Reference Levels in the Missouri/Southern Illinois Region Associated with Cone-beam Computed Tomography Use in Endodontics

INTRODUCTION

Diagnostic reference levels (DRLs) are intended to improve patient safety and ensure that patient ionizing radiation doses are as low as reasonably achievable. The purpose of this dosimetry study was to establish regional DRL levels for cone-beam computed tomography (CBCT) imaging for specialty endodontics. Another aim was to compare phantom-measured ionizing radiation dose index 1 (DI1) index doses to the manufacturer-provided dose area product (DAP) radiation output values for each of the CBCT machines studied, to ascertain their degree of correlation. DAP refers to the dose area product, a measure of radiation dose monitoring which represents the dose within the beam times the area within the beam at that position.

METHODS

A thimble ionization chamber and polymethyl methacrylate phantom were used to obtain DI1 values using the SEDENTEXTCT method from 21 different CBCT units. DRLs were calculated based on the 75th percentile (third quartile) of the median output values.

RESULTS

The proposed DRL from the CBCT units surveyed has a DAP value of 838 mGy cm2 and a DI1 value of 3.924 mGy. DAP versus DI1 values of 500.6 mGy cm2 versus 2.006 mGy, and 838 mGy cm2 versus 3.906 mGy represented the third quartile of the median values for the 4-cm × 4-cm and 5-cm × 5-cm field of views (FOVs), respectively.

CONCLUSIONS

The DI1 and DAP values strongly correlated when 3 outlier CBCT machines (J Morita Veraview X800) using a novel 360° (full rotation) acquisition mode were excluded. The importance of selectable exposure parameters as directly related to ionizing radiation output is illustrated among the CBCT units surveyed. Although the actual FOV that is selected is ultimately dictated by the specific clinical requirements, a 4-cm × 4-cm FOV is recommended for specialist endodontics practice, whenever clinically practical, based on the decreased ionizing radiation output, as compared to that from a 5-cm × 5-cm FOV.

Establishment of Diagnostic Reference Levels in Cone Beam Computed Tomography Scans in the United Arab Emirates

This study aimed to address the knowledge gap in assessing the radiation doses from cone beam computed tomography (CBCT) procedures, establishing a typical value, and estimating effective and organ doses. A total of 340 patients aged 18-80 years were included in this study. Organ doses were estimated using VirtualDose IR software. The typical values were based on median values estimated as 1000 mGy cm². The mean ED (µSv) per procedure was 149.5 ± 56, and the mean of the peak skin dose during the CBCT examination was 39.29 mGy. The highest organ dose was received by the salivary glands (2.71 mGy), the extrathoracic region (1.64 mGy), thyroid (1.24 mGy) and eyes (0.61 mGy). The patients' doses were higher than in previous studies. Staff awareness, education, training and dose optimisation are highly recommended. With the establishment of local DRLs, patient dosages can be reduced successfully without compromising image quality.

NATIONWIDE SURVEY OF RADIATION EXPOSURE FOR RADIOFREQUENCY CATHETER ABLATION FOR PULMONARY VEIN ISOLATION AND NONPULMONARY VEIN ISOLATION IN JAPAN

To propose typical values for the arrhythmia region between pulmonary vein isolation (PVI) and nonpulmonary vein isolation (non-PVI) in Japan. A nationwide questionnaire was posted to 343 facilities, to which 125 facilities (36.4%) responded. Results is the median for PVI and non-PVI were in terms of Ka,r (317 and 196 mGy), PKA (40.8 and 26.3 Gy.cm2), FT (43.0 and 27.3 min), and CI (326 and 102 images). When comparing PVI and non-PVI procedures, there were significant differences in Ka, r, PKA, FT, and CI (p < 0.05). In other words, by classifying into two types, PVI and non-PVI, we contributed to the establishment of typical values in Japan's RFCA.

APPLICATIONS OF OPTICALLY STIMULATED LUMINESCENCE IN MEDICAL DOSIMETRY

If the first decade of the new millennium saw the establishment of a more solid foundation for the use of the Optically Stimulated Luminescence (OSL) in medical dosimetry, the second decade saw the technique take root and become more widely used in clinical studies. Recent publications report not only characterization and feasibility studies of the OSL technique for various applications in radiotherapy and radiology, but also the practical use of OSL for postal audits, estimation of staff dose, in vivo dosimetry, dose verification and dose mapping studies. This review complements previous review papers and reports on the topic, providing a panorama of the new advances and applications in the last decade. Attention is also dedicated to potential future applications, such as LET dosimetry, 2D/3D dosimetry using OSL, dosimetry in magnetic resonance imaging-guided radiotherapy (MRIgRT) and dosimetry of extremely high dose rates (FLASH therapy).

Establishment of national diagnostic reference levels in dental cone beam computed tomography in Switzerland

OBJECTIVES

The aim of this study was to establish diagnostic reference levels (DRLs) in the field of dental maxillofacial and ear-nose-throat (ENT) practices using cone beam CT (CBCT) in Switzerland.

METHODS

A questionnaire was sent to owners of CBCTs in Switzerland; to a total of 612 institutions. The answers were analyzed for each indication, provided that enough data were available. The DRLs were defined as the 75th percentile of air kerma product distribution (PKA).

RESULTS

227 answers were collected (38% of all centers). Third quartile of PKA values were obtained for five dental indications: 662 mGy cm² for wisdom tooth, 683 mGy cm² for single tooth implant treatment, 542 mGy cm² for tooth position anomalies, 569 mGy cm² for pathological dentoalveolar modifications, and 639 mGy cm² for endodontics. The standard field of view (FOV) size of 5 cm in diameter x 5 cm in height was proposed.

CONCLUSIONS

Large ranges of FOV and PKA were found for a given indication, demonstrating the importance of establishing DRLs as well as FOV recommendations in view of optimizing the present practice. For now, only DRLs for dental and maxillofacial could be defined; because of a lack of ENT data, no DRL values for ENT practices could be derived from this survey.

IAEA survey of dental cone beam computed tomography practice and related patient exposure in nine Central and Eastern European countries

OBJECTIVES

Cone beam CT (CBCT) in dentistry and maxillofacial surgery is a widely used imaging method for the assessment of various maxillofacial and dental pathological conditions. The objective of this study was to summarize the results of a multinational retrospective-prospective study that focused on patient exposure in this modality.

METHODS

The study included 27 CBCT units and 325 adult and paediatric patients, in total. Data on patients, clinical indications, technical parameters of exposure, patient dose indicator, or, alternatively, dose to phantom were collected. The dose indicator used was air kerma-area product, P_KA.

RESULTS

In most scanners operators are offered with a variety of options regarding technical parameters, especially the field of view size. The median and the third quartile value of P_KA for adult patients in 14 different facilities were 820 mGy cm² and 1000 mGy cm² (interquartile range = 1058 mGy cm²), and 653 mGy cm² and 740 mGy cm² (interquartile range = 1179 mGy cm²) for children, as reported by four different institutions. Phantom dose data were reported from 15 institutions, and median P_KA ranged from 125 mGy cm² to 1951 mGy cm². Median P_KA values varied by more than a 10-fold between institutions, mainly due to differences in imaging protocol used, in particular field of view and tube current-exposure time product.

CONCLUSIONS

The results emphasize the need for a cautious approach to using dental CBCT. Imaging only when the clinical indications are clear, accompanied with the appropriate radiographic techniques and the optimum imaging protocol, will help reduce radiation dose to patients.

Evaluation of different soft tissue-simulating materials in pixel intensity values in cone beam computed tomography

OBJECTIVE

This study aimed to evaluate different materials as soft tissue simulators and the influence of soft tissues in cone beam computed tomography.

STUDY DESIGN

Images of 5 piglet heads were acquired with intact soft tissues, with the tissues stripped, and with the use of different soft tissue simulators, following the same acquisition protocol. Four different materials were tested, individually or in combination: acrylic, water, utility wax, and expanded polystyrene (EPS). Pixel intensity values of 8 quadrangular regions, that is, upper and lower teeth and alveolar bone, were obtained. The mean values were used for comparison by analysis of variance (ANOVA; α = 5%).

RESULTS

No differences were observed for the "No Material," "EPS," "Acrylic," and "EPS and Wax" groups for the lower anterior and posterior teeth, the upper posterior tooth, and the anterior and posterior bone, and for the "No Material," "EPS," and "EPS and Wax," groups for the lower posterior bone. All groups showed statistical differences for the lower anterior bone and the upper anterior tooth.

CONCLUSIONS

Expanded 2-cm thick polystyrene, with or without 1-cm thick utility wax, was effective for most regions, followed by acrylic 0.5 cm. Soft tissues were not of great influence in most regions. Water was not an effective material for any of the regions.

Dose area product in estimation of effective dose of the patients undergoing dental cone beam computed tomography examinations

OBJECTIVE

To investigate the relationship of the effective dose and dose area product (DAP) in dental cone beam computed tomography (CBCT) examinations and to propose conversion factors for estimation of effective doses of the patients using DAP. Dependence of organ doses on DAP was also investigated.

MATERIALS AND METHODS

Different exposure geometries in Cranex3Dx CBCT device were simulated using Monte Carlo simulation and computational anthropomorphic phantom. Then organ doses and effective dose for every exposure geometry was compared to DAP and analysed.

RESULTS

The effective dose in all simulated CBCT protocols and positions with 180° tube rotation ranged from 5 μSv for 50 × 50 mm² field of view (FOV) localised on one tooth using lowest resolution to 265 μSv for the largest FOV and highest resolution. In case of 360° tube rotation the effective dose ranges from 6 to 332 μSv for the same FOV sizes and positions as well as resolutions as in 180° tube rotation.

CONCLUSIONS

Though the DAP introduces a large uncertainty in the risk measure in dental CBCT, it represents the dose and FOV size which are the most important scanning parameters affecting the dose. To decrease uncertainty in the risk measure, the effective dose has to be estimated for usual clinical positions of the FOV.

Impact of voxel size and scan time on the accuracy of three-dimensional radiological imaging data from cone-beam computed tomography

PURPOSE

Three-dimensional (3D) radiological imaging plays an important role in surgical planning used in modern dentistry. The aim of this study was to optimize imaging parameters with a special focus on voxel size and scan time.

MATERIAL AND METHODS

A virtual 3D master model of a macerated human skull was generated using an industrial optical noncontact white light scanner. The skull was X-rayed with cone-beam computed tomography that was applied using different settings for voxel size and acquisition time (voxel edge length of 0.3 mm, scan times 4.8 s and 8.9 s; voxel edge length of 0.2 mm, scan times 14.7 s and 26.9 s). The scan was repeated 10 times at each setting. The CBCT scans were converted into 3D virtual models (actual value), which were superimposed with the 3D master model (reference value) to detect absolute differences.

RESULTS

The mean value of deviation increased with increasing voxel size and decreasing scan time. For a voxel edge length of 0.3 mm, the mean values of deviation were 0.33 mm and 0.22 mm with scan times of 4.8 s and 8.9 s, respectively. For a voxel edge length of 0.2 mm, the mean deviations were 0.16 mm and 0.14 mm with scan times of 14.7 s and 26.9 s, respectively.

CONCLUSIONS

When using small voxel sizes, the scan time does not have a significant impact on image accuracy and therefore the scan time can be shortened. However, for larger voxel sizes, shorter scan times can lead to increased inaccuracy.

Clinical guidelines for dental cone-beam computed tomography

Dental cone-beam computed tomography (CBCT) received regulatory approval in Japan in 2000 and has been widely used since being approved for coverage by the National Health Insurance system in 2012. This imaging technique allows dental practitioners to observe and diagnose lesions in the dental hard tissue in three dimensions (3D). When performing routine radiography, the examination must be justified, and optimal protection should be provided according to the ALARA (as low as reasonably achievable) principles laid down by the International Commission on Radiological Protection. Dental CBCT should be performed in such a way that the radiation exposure is minimized and the benefits to the patient are maximized. There is a growing demand for widespread access to cutting-edge health care through Japan's universal health insurance system. However, at the same time, people want our limited human, material, and financial resources to be used efficiently while providing safe health care at the least possible cost to society. Japan's aging population is expected to reach a peak in 2025, when most of the baby boomer generation will be aged 75 years or older. Comprehensive health care networks are needed to overcome these challenges. Against this background, we hope that this text will contribute to the nation's oral health by encouraging efficient use of dental CBCT.

Dental cone beam CT: A review

For the maxillofacial region, there are various indications that cannot be interpreted from 2D images and will benefit from multiplanar viewing. Dental cone beam CT (CBCT) utilises a cone- or pyramid-shaped X-ray beam using mostly flat-panel detectors for 3D image reconstruction with high spatial resolution. The vast increase in availability and amount of these CBCT devices offers many clinical benefits, and their ongoing development has potential to bring various new clinical applications for medical imaging. Additionally, there is also a need for high quality research and education. European guidelines promote the use of a medical physics expert for advice on radiation protection, patient dose optimisation, and equipment testing. In this review article, we perform a comparison of technical equipment based on manufacturer data, including scanner specific X-ray spectra, and describe issues concerning CBCT image reconstruction and image quality, and also address radiation dose issues, dosimetry, and optimisation. We also discuss clinical needs and what type of education users should have in order to operate CBCT systems safely. We will also take a look into the future and discuss the issues that still need to be solved.