The influence of acetabular inclination angle on the penetration of polyethylene and migration of the acetabular component

Wear of a Highly Cross-Linked Polyethylene Liner of the Acetabular Component Placed With Excessive Acetabular Inclination

Few studies have investigated the influence of excessive acetabular inclination during total hip arthroplasty (THA) on the wear of highly cross-linked polyethylene (HXLPE). The goal of this study was to determine whether excessive acetabular inclination during THA causes prominent wear of the HXLPE liner. We retrospectively evaluated 62 hips of 54 women and 8 men who underwent primary THA with an HXLPE liner between January 2006 and September 2011. Postoperative anteroposterior pelvic radiographs were used to measure acetabular inclination and analyze polyethylene wear. Patients were divided into the following groups: the excessive acetabular inclination group (acetabular inclination angle ≥50°; n=20) and the control group (acetabular inclination angle <50°; n=42). Clinical information and imaging findings were compared and examined between the 2 groups. Further, we evaluated the correlation between the acetabular inclination angle and the polyethylene wear rate. In all cases, mean follow-up duration was 6.3 years. The annual liner wear was 0.00446 and 0.0254 mm/y in the control and excessive acetabular inclination groups, respectively. The excessive acetabular inclination group had significantly higher polyethylene liner wear compared with the control group (P=.00991). A weak correlation was seen between acetabular inclination angle and polyethylene wear rate in all cases (Spearman's rank correlation, r=0.283, P=.0258). Excessive acetabular inclination may increase HXLPE liner wear in the long term. [Orthopedics. 2022;45(2):e96-e100.].

Radiographic results on acetabular cup placement with the SuperPath technique: a retrospective study of 756 cases

Background

The Supercapsular percutaneously assisted total hip (SuperPath) technique is a relatively new minimally invasive approach for total hip arthroplasty (THA). Good clinical outcomes related to its use are reported in the literature. Nonetheless, there are still uncertainties about its validity in terms of radiographic outcomes.

Main purpose of the study is to evaluate the effectiveness of the SuperPath in acetabular cup positioning through radiographic evaluation of acetabular inclination angle (IA) and acetabular anteversion (AA) angle within the safe zone described by Lewinnek. The leg length discrepancy (LLD), femoral offset (FO), and acetabular offset (AO) were also measured to ascertain the radiographic effectiveness of SuperPath in the acetabular cup placement.

Methods

Between January 2016 and December 2019, all SuperPath cases eligible for the study were included. They were operated by three orthopaedic surgeons with long-standing experience in THA via conventional posterolateral approach and who have performed SuperPath training fellowship. The Mann-Whitney U test was used for statistical assessments (p-value < 0.05). Means ± standard deviation (SD) of the radiographic IA and AA were calculated for each year.

Results

A retrospective analysis of 756 THAs was performed. The average percentage of IA within the Lewinnek’s safe zone was from 80 to 85%, while the average percentage of AA was from 76 to 79%. Both IA and AA showed no statistically significant difference between two consecutive years. Good results, in the ranges of normal values, were also obtained for LLD, FO and AO, with homogeneous outcomes between 1 year and the following one.

Conclusion

It is possible to achieve good radiographic values of acetabular cup orientation through the SuperPath within the Lewinnek’s safe zone. These results are similar to those reported in the literature by authors using SuperPath. Low rate (0,3%) of hip dislocations were reported. Therefore, the SuperPath technique represents a good alternative THA approach. Nevertheless, there is not a statistically significant improvement in these radiographic parameters over a four-year time.

Level of evidence

Level IV, retrospective study.

Ceramic-on-ceramic versus ceramic-on-polyethylene in total hip arthroplasty: a comparative study at a minimum of 13 years follow-up

BACKGROUND

Nowadays hip replacement is one of the most successful surgery in terms of clinical outcome and patient's satisfaction. Therefore, the choice of biomaterials in hip replacement is increasingly important with the aim of obtaining a long-term satisfaction of patient and a greater survivorship of the implants. Ceramic-on-polyethylene (COP) and ceramic-on-ceramic (CoC) bearings are two common coupling used in total hip arthroplasty. The aim of this retrospective study was to compare clinical and radiological outcomes between patients treated using CoC and CoP THA at a mean follow-up of 15 years.

METHODS

86 patients, average age 65.6, were included in the study: 43 in group A bearing CoC and 43 in group B bearing CoP. Minimum follow-up was 13 years. Primary outcome was a clinical evaluation assessed by HOOS and SF-12 questionnaires. Secondary outcome was a radiological evaluation on a A-P pelvis x-ray calculating acetabular cup inclination and anteversion and detecting osteolysis.

RESULT

After a multivariate analysis was performed, our results show clinical outcomes in group B significantly better than in group A: statistically significant value (p < 0,05) was found in the mean HOOS-symptoms subscale (83.0 ± 15.4 in Group A vs 90.3 ± 12.2 in group B) in the SF-12 physical component score (39.7 ± 11.0 in Group A vs 48.1 ± 10.1 in group B) and in HOOS (79.0 ± 16 in Group A vs 87.0 ± 16 in group B). 3 squeaking was found in group A. The calculated mean acetabular cup inclination value was 44,87 in group A and 44,5 in group B and the mean socket version was 17,54 in group A and 15,10 in group B. No significant statistically relationship between radiographic parameters analyzed and clinical outcomes was noted.

CONCLUSION

The current results provide us important information about the THA long-term outcome. CoP offered significantly better results compared with CoC at long-term follow up, and thus it should be considered in the choose of bearing in THA.

Results of a randomized controlled trial with five-year radiostereometric analysis results of vitamin E-infused highly crosslinked versus moderately crosslinked polyethylene in reverse total hip arthroplasty

Aims

Vitamin E-infused highly crosslinked polyethylene (VEPE) has been introduced into total hip arthroplasty (THA) with the aim of further improving the wear characteristics of moderately and highly crosslinked polyethylenes (ModXLPE and HXLPE). There are few studies analyzing the outcomes of vitamin E-infused components in cemented arthroplasty, though early acetabular component migration has been reported. The aim of this study was to measure five-year polyethylene wear and acetabular component stability of a cemented VEPE acetabular component compared with a ModXLPE cemented acetabular component.

Methods

In a prospective randomized controlled trial (RCT), we assessed polyethylene wear and acetabular component stability (primary outcome) with radiostereometric analysis (RSA) in 68 patients with reverse hybrid THA at five years follow-up. Patients were randomized to either a VEPE or a ModXLPE cemented acetabular component.

Results

Mean polyethylene wear in the proximal direction was 0.17 mm (SD 0.15) for the VEPE group and 0.20 mm (SD 0.09) for the ModXLPE group (p = 0.005) at five years. Annual proximal wear rates were 0.03 mm/year (VEPE) and 0.04 mm/year (ModXLPE). Total 3D wear was 0.21 mm (SD 0.26) and 0.23 mm (SD 0.10) for the VEPE and ModXLPE groups, respectively (p = 0.009). Total 3D cup translation was 0.72 mm (SD 0.70) (VEPE) and 0.50 mm (SD 0.44) (ModXLPE) (p = 0.409).

Conclusion

At five years, there was less polyethylene wear in the VEPE group than in the ModXLPE group. Both VEPE and ModXLPE cemented components showed low annual wear rates. Component stability was similar in the two groups and remained constant up to five years. Whether these results will equate to a lower long-term revision rate is still unknown. Cite this article: Bone Joint J 2020;102-B(12):1646–1653.

Inferior stabilization of cementless compared with cemented dual-mobility cups in elderly osteoarthrosis patients: a randomized controlled radiostereometry study on 60 patients with 2 years' follow-up

Background and purpose - Elderly patients may benefit from a dislocation low-risk dual-mobility (DM) articulation in total hip arthroplasty, but the best cup fixation method is unknown. We compared cup migration for cemented and cementless DM cups using radiostereometry.Patients and methods - In a patient-blinded randomized trial, 60 patients (33 female) with osteoarthritis were allocated to cemented (n = 30) or cementless (n = 30) Avantage DM cup fixation. Criteria were age above 70 years, and T-score above -4. We investigated cup migration, periprosthetic bone mineral density (BMD), and patient-reported outcome measures (PROMs) until 24 months postoperative follow-up.Results - At 24 months mean proximal cup migration was 0.11 mm (95% CI 0.00-0.23) for cemented cups and 0.09 mm (CI -0.09 to 0.28) for cementless cups. However, cementless cups generally migrated more than cemented cups at 12 and 24 months. Cemented cups had no measurable migration from 3 months' follow-up, while cementless cups had not yet stabilized at 24 months in all rotations. Cementless cups showed statistically significantly more maximum total point motion (MTPM) at 12- and 24-month follow-up compared with cemented cups in patients with low systemic BMD (p = 0.01). Periprosthetic BMD changes did not statisticially significantly correlate to proximal migration in either cup fixation group (p > 0.05). PROMs improved similarly in both groups.Interpretation - Cemented cups were well fixed at 3 months. The cementless cups migrated more in patients with low BMD, showed an inconsistent pattern of migration, and migrated in different directions during the first and second year without tendency to stabilization. Cemented fixation of the Avantage DM cup seems safer in elderly patients.

Component Placement in Direct Lateral vs Minimally Invasive Anterior Approach in Total Hip Arthroplasty: Radiographic Outcomes From a Prospective Randomized Controlled Trial

BACKGROUND

End-stage coxarthrosis is increasingly common; however, limited evidence exists on the effect of direct lateral approach (DLA) and minimally invasive direct anterior approach (MIDA) on component placement in total hip arthroplasty (THA). We therefore conducted a prospective, randomized controlled trial to determine the component placement in DLA vs MIDA in THA.

METHODS

Between January 2012 and June 2013, 164 patients with clinically and radiologically confirmed coxarthrosis aged 20-80 years were randomized to either DLA or MIDA (active comparator). Excluded were patients with previous ipsilateral hip surgery, a body mass index >35 kg/m², and/or mental disability. Primary clinical outcomes have been published elsewhere. Secondary outcomes included radiographic assessment of the acetabular component (cement-mantle thickness, inclination, and anteversion), femoral stem position (varus/valgus and THA index), offset restoration, and leg length discrepancy.

RESULTS

The mean cement-mantle was significantly thicker in zone 1 in the MIDA group (mean difference = 0.51 mm, 95% confidence interval [CI] 0.09-0.93, P = .018), and the mean degrees of inclination and anteversion were higher in the MIDA group (mean difference = 2.5°, 95% CI 0.3-4.6, P = .023 and mean difference = 3.6°, 95% CI 2.2-5.0, P < .0001, respectively). According to the defined reference range, cup inclination was more often adequate in the DLA group (67.9% (53/78) in the DLA group vs 52.4% (43/82) in the MIDA group, P = .045). There were no differences in frontal or lateral femoral stem position, global offset restoration, or leg length discrepancy.

CONCLUSION

In this population of Norwegian patients with coxarthrosis, radiographic assessment showed limited differences in component placement between MIDA and DLA. The findings suggest that component placement is similar in the 2 surgical approaches.

Patient-specific hip geometry has greater effect on THA wear than femoral head size

In vivo linear penetration in total hip arthroplasty (THA) exhibits similar values for 28mm and 32mm femoral head diameter with considerable variations between and within the studies. It indicates factors other than femoral head diameter influence polyethylene wear. This study is intended to test the effect of patient׳s individual geometry of musculoskeletal system, acetabular cup orientation, and radius of femoral head on wear. Variation in patient׳s musculoskeletal geometry and acetabular cup placement is evaluated in two groups of patients implanted with 28mm and 32mm THA heads. Linear wear rate estimated by mathematical model is 0.165-0.185mm/year and 0.157-0.205mm/year for 28 and 32mm THA heads, respectively. Simulations show little influence femoral head size has on the estimated annual wear rate. Predicted annual linear wear depends mostly on the abduction angle of the acetabular cup and individual geometry of the musculoskeletal system of the hip, with the latter having the greatest affect on variation in linear wear rate.

Cheating the Acetabular Component Horizontally in Total Hip Arthroplasty

To avoid inadvertent vertical positioning of the acetabular component during total hip arthroplasty (THA), the authors routinely "cheat" component abduction an additional 10° horizontal (goal=30°). This likely increases the incidence of components placed into abduction of less than 30°, the clinical consequences of which are not well studied. The purpose of this study was to determine the clinical and radiographic outcomes in patients undergoing THA with acetabular components positioned in less than 30° of abduction as compared with those with components positioned between 30° and 50°. A retrospective review was performed of consecutive patients undergoing primary THA with horizontally cheated acetabular component position performed by a single surgeon. Patients were grouped into cohorts with either component abduction less than 30° or between 30° and 50°. Demographic data, operative data, and complications were recorded. Harris Hip Scores (HHS) and radiographic analysis were obtained from preoperative and most recent clinic visits. Between September 2004 and September 2010, 320 consecutive THA procedures were performed. A total of 149 hips had component abduction less than 30° (mean, 25.8°; range, 15.7°-29.4°). No components had greater than 50° of abduction. At an average 37-month follow-up, no significant difference in HHS was found between the 2 cohorts (P=.137). The horizontal cohort had no dislocations, component loosening, or osteolysis. By cheating the acetabular component more horizontal, an excessively vertical position was avoided. Component abduction less than 30° yielded equivalent clinical outcomes to component abduction between 30° and 50°. [Orthopedics. 2016; 39(6):e1092-e1096.].

Oxidized zirconium head on crosslinked polyethylene liner in total hip arthroplasty: a 7- to 12-year in vivo comparative wear study

BACKGROUND

Osteolysis resulting from wear debris production from the bearing surfaces is a major factor limiting long-term survival of hip implants. Oxidized zirconium head on crosslinked polyethylene (XLPE) is a modern bearing coupling. However, midterm in vivo wear data of this coupling are not known.

QUESTIONS/PURPOSES

The purpose of this study was to investigate in vivo whether the combination of an oxidized zirconium femoral head on XLPE produces less wear than a ceramic head on XLPE or a ceramic head on conventional polyethylene (CPE) couplings and whether any of these bearing combinations results in higher hip scores.

METHODS

Between 2003 and 2007, we performed 356 total hip arthroplasties in 288 patients; of those, 199 (69.1%) patients (199 hips) were enrolled in what began as a randomized trial. Unfortunately, after the 57(th) patient, the randomization process was halted because of patients' preference for the oxidized zirconium bearing instead of the ceramic after (as they were informed by the consent form), and after that, alternate allocation to the study groups was performed. Hips were allocated into four groups: in Group A, a 28-mm ceramic head on CPE was used; in Group B, a 28-mm ceramic head on XLPE; in Group C, a 28-mm Oxinium head on XLPE; and in Group D, a 32-mm Oxinium head on XLPE. The authors prospectively collected in vivo wear data (linear wear, linear wear rate, volumetric wear, and volumetric wear rate) using PolyWare software. Preoperative and postoperative clinical data, including Harris and Oxford hip scores, were also collected at regular intervals. Of those patients enrolled, 188 (95%) were available for final followup at a minimum of 7 years (mean, 9 years; range, 7-12 years).

RESULTS

All bearing surfaces showed a varying high bedding-in effect (plastic deformation of the liner) up to the second postoperative year. At 5 years both oxidized zirconium on XLPE groups showed lower (p < 0.01) volumetric wear (mean ± SD mm(3)) and volumetric wear rates (mean ± SD mm(3)/year) (Group C: 310 ± 55-206 ± 55 mm(3)/year, Group D: 320 ± 58-205 ± 61 mm(3)/year) when compared with ceramic on CPE (Group A: 791 ± 124-306 ± 85 mm(3)/year) and ceramic on XLPE (Group B: 1420 ± 223-366 ± 88 mm(3)/year) groups. For those patients who had completed 10 years of followup (20 patients [44.5%] of Group A, 21 [45.7%] of Group B, 23 [47.9%] of Group C, and 22 [44.9%] of Group D), at 10 years, both oxidized zirconium on XLPE groups also showed lower (p < 0.01) volumetric wear (mean ± SD mm(3)) and volumetric wear rates (mean ± SD mm(3)/year) (Group C: 356 ± 64 to 215 ± 54 mm(3)/year, Group D: 354 ± 50 to 210 ± 64 mm(3)/year) when compared with ceramic on CPE (Group A: 895 ± 131 to 380 ± 80 mm(3)/year) and ceramic on XLPE (Group B: 1625 ± 253 to 480 ± 101 mm(3)/year) groups. When wear rates of both oxidized zirconium groups were compared, no differences were found at any time interval with the numbers available. Two hips (one from Group A and one from Group B) are scheduled for revision as a result of wear and osteolysis. There were no differences in hip scores among the groups with the numbers available.

CONCLUSIONS

In this study, in vivo wear parameters were lower when the combination of an oxidized zirconium head on XLPE liner was used at an average of 9 years (range, 7-12 years) followup. Further larger-scale clinical studies should confirm these findings and evaluate osteolysis and revision rates in association with the use of this bearing coupling.

LEVEL OF EVIDENCE

Level II, therapeutic study.

Primary cup stability in THA with augmentation of acetabular defect. A comparison of healthy and osteoporotic bone

BACKGROUND CONTEXT

Reconstruction of acetabular defect has been advocated as standard procedure in total hip arthroplasty. The presence of bony defects at the acetabulum is viewed as a cause of instability and acetabular wall augmentation is often used without proper consideration of surrounding bone density. The initial cup-bone stability is, however, a challenge and a number of studies supported by clinical follow-ups of patients suggested that if the structural graft needs supporting more than 50% of the acetabular component, a reconstruction cage device spanning ilium to ischium should be preferred to protect the graft and provide structural stability. This study aims to (1) investigate the relationship between cup motion and bone density and (2) quantify the re-distribution of stress at the defect site after augmentation.

HYPHOTESIS

Paprosky type I or II, acetabular defects, when reconstructed with bone screws supported by bioabsorbable calcified triglyceride bone cement are significantly less effective for osteoporotic bone than healthy bone.

MATERIALS AND METHODS

Acetabular wall defects were reconstructed on six cadaveric subjects with bioabsorbable calcified triglyceride bone cement using a re-bar technique. Data of the specimen with higher bone density was used to validate a Finite Element Model. Values of bone apparent density ranging from healthy to osteoporotic were simulated to evaluate (1) the cup motion, through both displacement and rotation, (2) and the von Mises stress distribution.

RESULTS

Defect reconstruction with bone screws and bioabsorbable calcified triglyceride bone cement results in a re-distribution of stress at the defect site. For a reduction of 65% in bone density, the cup displacement was similar to a healthy bone for loads not exceeding 300 N, as load progressed up to 1500 N, the reconstructed defect showed increase of 99 μm (128%) in displacement and of 0.08° in rotation angle.

CONCLUSIONS

Based on the results, we suggest that an alternative solution to wall defect augmentation with bone screws supported by bioabsorbable calcified triglyceride bone cement, be used for osteoporotic bone.

LEVEL OF EVIDENCE

Level IV, experimental and cadaveric study.

Mechanisms of plastic deformation in highly cross-linked UHMWPE for total hip components--the molecular physics viewpoint

Plastic deformation is an unavoidable event in biomedical polymeric implants for load-bearing application during long-term in-vivo service life, which involves a mass transfer process, irreversible chain motion, and molecular reorganization. Deformation-induced microstructural alterations greatly affect mechanical properties and durability of implant devices. The present research focused on evaluating, from a molecular physics viewpoint, the impact of externally applied strain (or stress) in ultra-high molecular weight polyethylene (UHMWPE) prostheses, subjected to radiation cross-linking and subsequent remelting for application in total hip arthroplasty (THA). Two different types of commercial acetabular liners, which belong to the first-generation highly cross-linked UHMWPE (HXLPE), were investigated by means of confocal/polarized Raman microprobe spectroscopy. The amount of crystalline region and the spatial distribution of molecular chain orientation were quantitatively analyzed according to a combined theory including Raman selection rules for the polyethylene orthorhombic structure and the orientation distribution function (ODF) statistical approach. The structurally important finding was that pronounced recrystallization and molecular reorientation increasingly appeared in the near-surface regions of HXLPE liners with increasing the amount of plastic (compressive) deformation stored in the microstructure. Such molecular rearrangements, occurred in response to external strains, locally increase surface cross-shear (CS) stresses, which in turn trigger microscopic wear processes in HXLPE acetabular liners. Thus, on the basis of the results obtained at the molecular scale, we emphasize here the importance of minimizing the development of irrecoverable deformation strain in order to retain the pristine and intrinsically high wear performance of HXLPE components.