Fiber optic refractive index sensors through spectral detection of Rayleigh backscattering in a chemically etched MgO-based nanoparticle-doped fiber

Characterization of optical fibers doped with nanoparticles for distributed displacement sensing

High-scattering optical fibers have emerged as a key component in distributed sensing systems, primarily due to their capacity to enhance signal-to-noise ratio. This paper presents an experimental characterization of optical fibers doped with oxide nanoparticles for displacement sensing. They were manufactured using the phase-separation technique and different doping compounds, including calcium, strontium, lanthanum and magnesium. The Rayleigh backscattering (RBS) signatures in time and frequency domains were acquired using an Optical Backscatter Reflectometer (OBR). The maximum representative length, backscattering gain and strain sensitivity were evaluated. The results indicate that the fiber co-doped with magnesium and erbium chlorides offered the best compromise between strain sensitivity (0.96 pm/μ ϵ) and maximum length (17 m). For conditions of single and multiple perturbations, strain saturation was reached at ≥7000 μm and <1500 μm, respectively. In addition, the results reveal that, under a condition of variable temperature (30-60 °C), the sensor response becomes significantly nonlinear over length, requiring a technique for temperature cross-sensitivity mitigation that accounts for nonlinearities in sensitivity and hysteresis.

Strain measurement with adaptive local feature extraction method based on special fiber OFDR system

The optical fiber distributed strain sensor based on the optical frequency domain reflectometer (OFDR) preserves its dominant position in short-distance measurement fields with high spatial resolution, such as biomedical treatment, soft robot, etc. However, owing to the weak intensity of the Rayleigh backscattered signal (RBS) in the single-mode fiber (SMF) and complex computation, the large strain changes cannot be precisely and rapidly demodulated by the traditional cross-correlation method. In this work, the OFDR with backscattering enhanced optical fiber (BEOF) is proposed and demonstrated for fast and large strain measurement. By enhancing the RBS amplitude, the signal-to-noise ratio (SNR) is improved, resulting in a higher similarity between the reference signal and test signal, which is beneficial for the expansion of the strain measurement range. Moreover, the adaptive local feature extraction and matching (ALFEM) algorithm is presented and demonstrated, which replaces the traditional cross-correlation method for strain demodulation and fast measurement. On account of the enhancement ratio of BEOF, the dominant characteristic data segment can be extracted from whole wavelength data. In the experiments, the enhancing ratio of BEOF is designed as 10, resulting in the spatial resolution reaches 400µm and the strain measurement range is greatly increased to 4800µɛ. Further, the effectiveness of the ALFEM algorithm has been verified, in which the strain demodulation time is approximately 25% of that of the traditional method. This scheme fully exploits the enhancement characteristic of the BEOF and is also applicable to the systems based on other types of BEOF, different strain changes and sensing distances.

Distributed optical fiber biosensor based on optical frequency domain reflectometry

In situ acquisition of spatial distribution of biochemical substances is important in cell analysis, cancer detection and other fields. Optical fiber biosensors can achieve label-free, fast and accurate measurements. However, current optical fiber biosensors only acquire single-point of biochemical substance content. In this paper, we present a distributed optical fiber biosensor based on tapered fiber in optical frequency domain reflectometry (OFDR) for the first time. To enhance evanescent field at a relative long sensing range, we fabricate a tapered fiber with a taper waist diameter of 6 μm and a total stretching length of 140 mm. Then the human IgG layer is coated on the entire tapered region by polydopamine (PDA) -assisted immobilization as the sensing element to achieve to sense anti-human IgG. We measure shifts of the local Rayleigh backscattering spectra (RBS) caused by the refractive index (RI) change of an external medium surrounding a tapered fiber after immunoaffinity interactions by using OFDR. The measurable concentration of anti-human IgG and RBS shift has an excellent linearity in a range from 0 ng/ml to 14 ng/ml with an effective sensing range of 50 mm. The concentration measurement limit of the proposed distributed biosensor is 2 ng/ml for anti-human IgG. Distributed biosensing based on OFDR can locate a concentration change of anti-human IgG with an ultra-high sensing spatial resolution of 680 μm. The proposed sensor has a potential to realize a micron-level localization of biochemical substances such as cancer cells, which will open a door to transform single-point biosensor to distributed biosensor.

Distributed Refractive Index Sensing Based on Etched Ge-Doped SMF in Optical Frequency Domain Reflectometry

A distributed optical fiber refractive index sensor based on etched Ge-doped SMF in optical frequency domain reflection (OFDR) was proposed and demonstrated. The etched Ge-doped SMF was obtained by only using wet-etching, i.e., hydrofluoric acid solution. The distributed refractive index sensing is achieved by measuring the spectral shift of the local RBS spectra using OFDR. The sensing length of 10 cm and the spatial resolution of 5.25 mm are achieved in the experiment. The refractive index sensing range is as wide as 1.33-1.44 refractive index units (RIU), where the average sensitivity was about 757 GHz/RIU. Moreover, the maximum sensitivity of 2396.9 GHZ/RIU is obtained between 1.43 and 1.44 RIU.

Perspectives on Assembling Coronavirus Spikes on Fiber Optics to Reveal Broadly Recognizing Antibodies and Generate a Universal Coronavirus Detector

In time of COVID-19 biological detection technologies are of crucial relevance. We propose here the use of state of the art optical fiber biosensors to address two aspects of the fight against SARS-CoV-2 and other pandemic human coronaviruses (HCoVs). Fiber optic biosensors functionalized with HCoV spikes could be used to discover broadly neutralizing antibodies (bnAbs) effective against known HCoVs (SARS-CoV, MERS-CoV and SARS-CoV-2) and likely future ones. In turn, identified bnAbs, once immobilized onto fiber optic biosensors, should be capable to detect HCoVs as diagnostic and environmental sensing devices. The therapeutic and preventative value of bnAbs is immense as they can be used for passive immunization and for the educated development of a universal vaccine (active immunization). Hence, HCoV bnAbs represent an extremely important resource for future preparedness against coronavirus-borne pandemics. Furthermore, the assembly of bnAb-based biosensors constitutes an innovative approach to counteract public health threats, as it bears diagnostic competence additional to environmental detection of a range of pandemic strains. This concept can be extended to different pandemic viruses, as well as bio-warfare threats that entail existing, emerging and extinct viruses (e.g., the smallpox-causing Variola virus). We report here the forefront fiber optic biosensor technology that could be implemented to achieve these aims.

Temperature-compensated distributed refractive index sensor based on an etched multi-core fiber in optical frequency domain reflectometry

We proposed a temperature-compensated distributed refractive index (RI) sensor using an etched multi-core fiber (MCF) in optical frequency domain reflectometry. The MCF contains inner and outer cores and is etched until the outer core is exposed. Therefore, the outer core can be used for distributed RI sensing, and the inner core can be used for temperature compensation. The sensing length of 19 cm and the spatial resolution of 5.3 mm are achieved in the experiment. The RI sensing range is as wide as 1.33-1.44 refractive index units (RIU), and the maximum sensitivity of 47 nm/RIU is obtained around 1.44 RIU. Additionally, the temperature sensitivity is 9.8 pm/°C. Using this sensor, we successfully detected the glycerol diffusion process in water.

Distributed refractive index sensing based on bending-induced multimodal interference and Rayleigh backscattering spectrum

A distributed refractive index (RI) sensor based on high-performance optical frequency domain reflectometry was developed by bending a piece of standard single-mode fiber to excite sets of higher-order modes that penetrate the surrounding medium. External variations in RI modifies the profiles of the sets of excited higher-order modes, which are then partially coupled back into the fiber core and interfere with the fundamental mode. Accordingly, the fundamental mode carries the outer varied RI information, and RI sensing can be achieved by monitoring the wavelength shift of the local Rayleigh backscattered spectra. In the experiment, an RI sensitivity of 39.08 nm/RIU was achieved by bending a single-mode fiber to a radius of 4 mm. Additionally, the proposed sensor maintains its buffer coating intact, which boosts its practicability and application adaptability.

Temperature-compensated multi-point refractive index sensing based on a cascaded Fabry-Perot cavity and FMCW interferometry

We proposed a novel temperature-compensated multi-point refractive index (RI) sensing system by the combination of the cascaded Fabry-Perot (FP) sensors and the frequency modulated continuous wave (FMCW) interferometry. The former is used for simultaneous sensing of RI and temperature, and the latter is used for multiplexing a series of the cascaded FP sensors to realize multi-point sensing. By means of Fourier transform-based algorithms, the interference spectra of each sub-FP sensors can be divided and demodulated independently. Experimentally, three cascaded FP sensors are multiplexed to verify multi-point RI and temperature sensing ability. RI sensitivity up to ∼1200 nm/RIU is obtained within RI range from 1.3330 to 1.3410, and temperature sensitivity up to ∼0.17 nm/°C is obtained within temperature range from 20 °C to 80 °C. The RI precision is as high as 10^-5 RIU and the temperature precision is as high as 0.05 °C. In addition, the prospective multiplexing number could reach about 4000 estimated by the minimum detectable light power. The proposed sensing system has potential advantages in the practical applications that require a large number sensing points.

Performance Study of a Zirconia-Doped Fiber for Distributed Temperature Sensing by OFDR at 800 °C

Optical Frequency Domain Reflectometry (OFDR) is used to make temperature distributed sensing measurements along a fiber by exploiting Rayleigh backscattering. This technique presents high spatial and high temperature resolutions on temperature ranges of several hundred of degrees Celsius. With standard telecommunications fibers, measurement errors coming from the correlation between a high temperature Rayleigh trace and the one taken as a reference at room temperature could be present at extremely high temperatures. These correlation errors, due to low backscattering signal amplitude and unstable backscattering signal, induce temperature measurement errors. Thus, for high temperature measurement ranges and at extremely high temperatures (e.g., at 800 °C), a known solution is to use fibers with femtosecond laser inscribed nanograting. These fs-laser-insolated fibers have a high amplitude and thermally stable scattering signal, and they exhibit lower correlation errors. In this article, temperature sensing at 800 °C is reported by using an annealed zirconia-doped optical fiber with an initial 40.5-dB enhanced scattering signal. The zirconia-doped fiber presents initially OFDR losses of 2.8 dB/m and low OFDR signal drift at 800 °C. The ZrO₂-doped fiber is an alternative to nanograting-inscribed fiber to make OFDR distributed fiber sensing on several meters with gauge lengths of 1 cm at high temperatures.

Engineering nanoparticle features to tune Rayleigh scattering in nanoparticles-doped optical fibers

Rayleigh scattering enhanced nanoparticles-doped optical fibers are highly promising for distributed sensing applications, however, the high optical losses induced by that scattering enhancement restrict considerably their sensing distance to few meters. Fabrication of long-range distributed optical fiber sensors based on this technology remains a major challenge in optical fiber community. In this work, it is reported the fabrication of low-loss Ca-based nanoparticles doped silica fibers with tunable Rayleigh scattering for long-range distributed sensing. This is enabled by tailoring nanoparticle features such as particle distribution size, morphology and density in the core of optical fibers through preform and fiber fabrication process. Consequently, fibers with tunable enhanced backscattering in the range 25.9-44.9 dB, with respect to a SMF-28 fiber, are attained along with the lowest two-way optical losses, 0.1-8.7 dB/m, reported so far for Rayleigh scattering enhanced nanoparticles-doped optical fibers. Therefore, the suitability of Ca-based nanoparticles-doped optical fibers for distributed sensing over longer distances, from 5 m to more than 200 m, becomes possible. This study opens a new path for future works in the field of distributed sensing, since these findings may be applied to other nanoparticles-doped optical fibers, allowing the tailoring of nanoparticle properties, which broadens future potential applications of this technology.

Reflector-less nanoparticles doped optical fiber biosensor for the detection of proteins: Case thrombin

A miniature biosensing platform based on MgO-based nanoparticle doped optical fiber was developed for the biomolecule detection. The technology used a single mode fiber with MgO-based nanoparticles doped core. The detection was based on collecting the Rayleigh backscattering signatures with increased gain upon the etching of the fiber 1-2 mm away from the tip. The shift from the backscattered signal with the maximum value of the cross-correlation was used to report the results. The sensor exhibited a sensitivity range from 0.75 nm/refractive index unit up to 19.63 nm/refractive index unit for a refractive index range from 1.3329 up to 1.37649. The deposition of the thin gold layer increased the overall sensitivity of the biosensor by 3.7 times for the etched part of the fiber with diameter 8-9 μm. The proposed biosensor was tested for the detection of thrombin molecule concentrations ranging from 0.625 μg/ml to 20 μg/ml. Thiol modified DNA specific aptamers were used to functionalize the gold coated surface of the fiber for the detection. The sensor showed detectable sensitivity and specificity as compared to the other control proteins. The proposed biosensing platform could be multiplexed and can be used in vivo for the detection in clinical settings due to its miniature size, biocompatibility of silica glass and reflector less set up.

Nano-Structured Optical Fibers Made of Glass-Ceramics, and Phase Separated and Metallic Particle-Containing Glasses

For years, scientists have been looking for different techniques to make glasses perfect: fully amorphous and ideally homogeneous. Meanwhile, recent advances in the development of particle-containing glasses (PCG), defined in this paper as glass-ceramics, glasses doped with metallic nanoparticles, and phase-separated glasses show that these “imperfect” glasses can result in better optical materials if particles of desired chemistry, size, and shape are present in the glass. It has been shown that PCGs can be used for the fabrication of nanostructured fibers—a novel class of media for fiber optics. These unique optical fibers are able to outperform their traditional glass counterparts in terms of available emission spectral range, quantum efficiency, non-linear properties, fabricated sensors sensitivity, and other parameters. Being rather special, nanostructured fibers require new, unconventional solutions on the materials used, fabrication, and characterization techniques, limiting the use of these novel materials. This work overviews practical aspects and progress in the fabrication and characterization methods of the particle-containing glasses with particular attention to nanostructured fibers made of these materials. A review of the recent achievements shows that current technologies allow producing high-optical quality PCG-fibers of different types, and the unique optical properties of these nanostructured fibers make them prospective for applications in lasers, optical communications, medicine, lighting, and other areas of science and industry.

Fiber Reshaping-Based Refractive Index Sensor Interrogated through Both Intensity and Wavelength Detection

A fiber reshaping-based refractive index (RI) sensor is proposed relying on both optical intensity variation and wavelength shift. The objective of this study is to completely reshape the core and to ultimately mimic a coreless fiber, thereby creating a highly efficient multimode interference (MMI) coupler. Thus, propagation modes are permitted to leak out into the cladding and eventually escape out of the fiber, depending on the surrounding environment. Two interrogation mechanisms based on both the intensity variation and wavelength shift are employed to investigate the performance of the RI sensor, with the assistance of leaky-mode and MMI theories. By monitoring the output intensity difference and the wavelength shift, the proposed RI sensor exhibits high average sensitivities of 185 dB/RIU and 3912 nm/RIU in a broad range from 1.339 to 1.443, respectively. The operating range and sensitivity can be adjusted by controlling the interaction length, which is appealing for a wide range of applications in industry and bioscience research.