Compound microstructures and wax layer of beetle elytral surfaces and their influence on wetting properties

Structural response and mechanical properties of the hind wing of the beetle Protaetia brevitarsis

The folding/unfolding mechanism and collision recovery effect of the beetle's hind wings can provide biomimetic inspiration for the optimization of wing deplorability and the investigation of collision prevention recovery mechanism of new amphibious morphing vehicle. In this study, a method is described to investigate the structural response and mechanical properties of the hind wings of the beetle Protetia brevitarsis under natural conditions. The specially processed test samples were conducted to tensile testing, which facilitates the evaluation of the mechanical properties of specific areas of the hind wing. The micro geometric morphological characteristics of the cross-section of the specimen after tensile fracture were observed by scanning electron microscopy. The three-dimensional morphology of the ventral and dorsal sides of the hind wing was characterized using three-dimensional scanning and reverse modeling methods. The finite element model of the hind wing is developed to investigate the structural deformation and modal response characteristics of its flapping. The uniformly distributed load on the hind wing surface is derived from the lift characteristics obtained from the computational fluid dynamics simulation of flapping wing motion. RESEARCH HIGHLIGHTS: Scanning electron microscope is used to observe the cross-sectional characteristics of the veins and membranes. The material properties of the wing membranes and veins of the hind wings were measured using the tensile testing system. The three-dimensional morphology of the hind wing was characterized using 3D scanning and reverse modeling methods. The finite element model of the hind wing is developed to investigate the structural deformation and modal response characteristics of its flapping.

Beetle elytra: evolution, modifications and biological functions

Conversion of forewings into hardened covers, elytra, was a ground-breaking morphological adaptation that has contributed to the extraordinary evolutionary success of beetles. Nevertheless, the knowledge of the functional aspects of these structures is still fragmentary and scattered across a large number of studies. Here, we have synthesized the presently available information on the evolution, development, modifications and biological functions of this crucial evolutionary novelty. The formation of elytra took place in the earliest evolution of Coleoptera, very likely already in the Carboniferous, and was achieved through the gradual process of progressive forewing sclerotization and the formation of inward directed epipleura and a secluded sub-elytral space. In many lineages of modern beetles, the elytra have been distinctly modified. This includes multiple surface modifications, a rigid connection or fusion of the elytra, or partial or complete reduction. Beetle elytra can be involved in a very broad spectrum of functions: mechanical protection of hind wings and body, anti-predator strategies, thermoregulation and water saving, water harvesting, flight, hind wing folding, diving and swimming, self-cleaning and burrow cleaning, phoresy of symbiotic organisms, mating and courtship, and acoustic communication. We postulate that the potential of the elytra to take over multiple tasks has enormously contributed to the unparalleled diversification of beetles.

Cuticular Structures in Micropterous Crickets (Orthoptera, Gryllidae, Petaloptilini, Gryllomorphini)

Orthoptera is a very diverse group that has colonized practically all terrestrial ecosystems on the planet. They have adapted to live in the endogenous environment as well as in caves so that some species exhibit troglomorphic characteristics. This group has been extensively studied due to its economic and social importance; however, many basic morphological and biological questions remain to be solved. In this study, a comparative morphological study by scanning electron microscopy of different structures of eight species of micropteran crickets of the tribes Gryllomorphini and Petaloptilini, whose tegmina had lost their flight and song functionality was carried out. Special emphasis was placed on the tegmina and their possible relationship to reproductive functions. In addition, to assess troglomorphism in the genus Petaloptila, the biometric parameters of six other species have been considered. Actualization of the lifestyle of the studied species has also been carried out. The results show structures not previously described in this group (gland openings, setae, pores, or group of campaniform sensilla). Structures not previously described in this group have been detected, and tegmina (glandular openings and devoured tegmina) seem to confer a role in reproduction. Troglomorphisms are only observed in species of the subgenus Zapetaloptila. Statistically, significant differences have been found in characters such as cephalic elongation, ocular reduction, greater length of appendages, and depigmentation.

Optimized imaging methods for species-level identification of food-contaminating beetles

Identifying the exact species of pantry beetle responsible for food contamination, is imperative in assessing the risks associated with contamination scenarios. Each beetle species is known to have unique patterns on their hardened forewings (known as elytra) through which they can be identified. Currently, this is done through manual microanalysis of the insect or their fragments in contaminated food samples. We envision that the use of automated pattern analysis would expedite and scale up the identification process. However, such automation would require images to be captured in a consistent manner, thereby enabling the creation of large repositories of high-quality images. Presently, there is no standard imaging technique for capturing images of beetle elytra, which consequently means, there is no standard method of beetle species identification through elytral pattern analysis. This deficiency inspired us to optimize and standardize imaging methods, especially for food-contaminating beetles. For this endeavor, we chose multiple species of beetles belonging to different families or genera that have near-identical elytral patterns, and thus are difficult to identify correctly at the species level. Our optimized imaging method provides enhanced images such that the elytral patterns between individual species could easily be distinguished from each other, through visual observation. We believe such standardization is critical in developing automated species identification of pantry beetles and/or other insects. This eventually may lead to improved taxonomical classification, allowing for better management of food contamination and ecological conservation.

Microstructure and nanomechanical properties of the exoskeleton of an ironclad beetle (Zopherus haldemani)

This study examined natural composite structures within the remarkably strong exoskeleton of the southwestern ironclad beetle (Z. haldemani). Structural and nanomechanical analyses revealed that the exoskeleton's extraordinary resistance to external forces is provided by its exceptional thickness and multi-layered structure, in which each layer performed a distinct function. In detail, the epicuticle, the outmost layer, comprised 3%-5% of the overall thickness with reduced Young's moduli of 2.2-3.2 GPa, in which polygonal-shaped walls (2-3μm in diameter) were observed on the surface. The next layer, the exocuticle, consisted of 17%-20% of the total thickness and exhibited the greatest Young's moduli (∼15 GPa) and hardness (∼800 MPa) values. As such, this layer provided the bulk of the mechanical strength for the exoskeleton. While the endocuticle spanned 70%-75% of the total thickness, it contained lower moduli (∼8-10 GPa) and hardness (∼400 MPa) values than the exocuticle. Instead, this layer may provide flexibility through its specifically organized chitin fiber layers, known as Bouligand structures. Nanoindentation testing further reiterated that the various fibrous layer orientations resulted in different elastic moduli throughout the endocuticle's cross-section. Additionally, this exoskeleton prevented delamination within the composite materials by overlapping approximately 5%-19% of each fibrous stack with neighboring layers. Finally, the innermost layer, the epidermis contributing 5%-7 % of the total thickness, contains attachment sites for muscle and soft tissue that connect the exoskeleton to the beetle. As such, it is the softest region with reduced Young's modulus of ∼2-3 GPa and hardness values of ∼290 MPa. These findings can be applied to the development of innovative, fiber-reinforced composite materials.

Investigation of the selective color-changing mechanism of Dynastes tityus beetle (Coleoptera: Scarabaeidae)

Not only does the Dynastes tityus beetle display a reversible color change controlled by differences in humidity, but also, the elytron scale can change color from yellow-green to deep-brown in specified shapes. The results obtained by focused ion beam-scanning electron microscopy (FIB-SEM), show that the epicuticle (EPI) is a permeable layer, and the exocuticle (EXO) is a three-dimensional photonic crystal. To investigate the mechanism of the reversible color change, experiments were conducted to determine the water contact angle, surface chemical composition, and optical reflectance, and the reflective spectrum was simulated. The water on the surface began to permeate into the elytron via the surface elemental composition and channels in the EPI. A structural unit (SU) in the EXO allows local color changes in varied shapes. The reflectance of both yellow-green and deep-brown elytra increases as the incidence angle increases from 0° to 60°. The microstructure and changes in the refractive index are the main factors that influence the process of reversible color change. According to the simulation, the lower reflectance causing the color change to deep-brown results from water infiltration, which increases light absorption. Meanwhile, the waxy layer has no effect on the reflection of light. This study lays the foundation to manufacture engineered photonic materials that undergo controllable changes in iridescent color.

Colour-assisted variation in elytral ICP-OES-based ionomics in an aposematic beetle

Very little is known about how the elemental composition (ionome) of an insect cuticle varies as a result of different colouration. Using inductively-coupled plasma optical emission spectrometry (ICP-OES), we established ionomic profiles in microsamples of two adjacent regions of an insect cuticle with a contrasting colour pattern, namely, the black and orange regions of the elytra of the aposematic burying beetle Nicrophorus vespillo. The analysis revealed 53 elements (ranging in atomic weight from Na to Bi) occurring above the detection limit. The frequency of detectability of individual elements varied strongly, and only ten elements (Ba, Cu, Fe, K, Mg, Mn, P, Rb, Sb and Zn) were present in concentrations exceeding the detection limit in all the samples. The sum of concentrations of all elements in the orange regions of the elytra was 9% lower than in the black ones. The opposite distribution was displayed by the rare earth elements (REEs), the sum of which was 17% lower in the black elytral regions than in the orange ones. The concentrations of six elements were significantly higher in the black than in the orange regions: Al (by 97%), Cu (41%), Mn (14%), Na (46%), Se (97%) and W (47%). The concentrations of essential elements measured in both the black and orange regions exhibited very considerable variance: Ca (σ² = 1834; 1882, respectively), K (145; 82) P (97; 76), Na (84; 53), Mg (24; 26) and Ba (9; 13). This, in part, could be attributed to individual differences, e.g. those resulting from the consumption of animal carcasses of different quality/chemical composition, but interference between elements and the consequent lowering of measurement quality are also possible. We highlight the fact that deeper insight into the basic relationship between insect colouration and variation in elemental composition requires micro-sampling of the homogeneous layers of an exoskeleton.

Natural Architectures for Tissue Engineering and Regenerative Medicine

The ability to control the interactions between functional biomaterials and biological systems is of great importance for tissue engineering and regenerative medicine. However, the underlying mechanisms defining the interplay between biomaterial properties and the human body are complex. Therefore, a key challenge is to design biomaterials that mimic the in vivo microenvironment. Over millions of years, nature has produced a wide variety of biological materials optimised for distinct functions, ranging from the extracellular matrix (ECM) for structural and biochemical support of cells to the holy lotus with special wettability for self-cleaning effects. Many of these systems found in biology possess unique surface properties recognised to regulate cell behaviour. Integration of such natural surface properties in biomaterials can bring about novel cell responses in vitro and provide greater insights into the processes occurring at the cell-biomaterial interface. Using natural surfaces as templates for bioinspired design can stimulate progress in the field of regenerative medicine, tissue engineering and biomaterials science. This literature review aims to combine the state-of-the-art knowledge in natural and nature-inspired surfaces, with an emphasis on material properties known to affect cell behaviour.

NEXAFS imaging to characterize the physio-chemical composition of cuticle from African Flower Scarab Eudicella gralli

The outermost surface of insect cuticle is a high-performance interface that provides wear protection, hydration, camouflage and sensing. The complex and inhomogeneous structure of insect cuticle imposes stringent requirements on approaches to elucidate its molecular structure and surface chemistry. Therefore, a molecular understanding and possible mimicry of the surface of insect cuticle has been a challenge. Conventional optical and electron microscopies as well as biochemical techniques provide information about morphology and chemistry but lack surface specificity. We here show that a near edge X-ray absorption fine structure microscope at the National Synchrotron Light Source can probe the surface chemistry of the curved and inhomogeneous cuticle of the African flower scarab. The analysis shows the distribution of organic and inorganic surface species while also hinting at the presence of aragonite at the dorsal protrusion region of the Eudicella gralli head, in line with its biological function.

Biology serves as inspiration in materials development; this requires improved understanding of the surface chemistry responsible for processes which are being mimicked. Here, the authors report on the use of near edge X-ray absorption fine structure (NEXAFS) imaging to analyze the surface chemistry of insect cuticle.

Review on nanoparticles and nanostructured materials: history, sources, toxicity and regulations

Nanomaterials (NMs) have gained prominence in technological advancements due to their tunable physical, chemical and biological properties with enhanced performance over their bulk counterparts. NMs are categorized depending on their size, composition, shape, and origin. The ability to predict the unique properties of NMs increases the value of each classification. Due to increased growth of production of NMs and their industrial applications, issues relating to toxicity are inevitable. The aim of this review is to compare synthetic (engineered) and naturally occurring nanoparticles (NPs) and nanostructured materials (NSMs) to identify their nanoscale properties and to define the specific knowledge gaps related to the risk assessment of NPs and NSMs in the environment. The review presents an overview of the history and classifications of NMs and gives an overview of the various sources of NPs and NSMs, from natural to synthetic, and their toxic effects towards mammalian cells and tissue. Additionally, the types of toxic reactions associated with NPs and NSMs and the regulations implemented by different countries to reduce the associated risks are also discussed.

The influence of the topography and physico-chemical properties of the cuticle surface on the wettability and adhesive properties of the elytra of the dung beetle Geotrupes stercorarius (Coleoptera, Scarabaeidae)

The elytral surface of dung beetles is generally accepted to be self-cleaning due to its anti-adhesive properties. In this article, the wettability and adhesive properties of elytral surface (intact and treated with Acetone and Ethanol) of the beetle Geotrupes stercorarius were characterized. Since these properties are influenced by the surface structure and chemistry, the micro- and nanostructure of the elytra were observed using scanning electron microscopy and the surface roughness were estimated with white light interferometery, whereas the water contact angle and adhesion force of the elytra were evaluated using contact angle measurement device and force transducer, respectively. The results show that the microstructure of the elytra changed greatly after different chemical treatments and the changes in wettability were mainly related to the changes of elytra roughness after treatments. The differences in adhesion force between differently treated elytra and wet sand indicate that the molecular polarity of the elytral surface is decisive for its anti-adhesive (self-cleaning) property.

Small Structures, Big Droplets: The Role of Nanoscience in Fog Harvesting

Designing materials for water harvesting has gained much attention in recent years as water scarcity continues to be one of the biggest problems facing mankind. In this issue of ACS Nano, Xu et al. propose a new device for harvesting water from fog. They use conically shaped copper wires with periodic roughness to enhance condensation and transport of water drops. While the periodic roughness enhances drop coalescence and motion, the conical shape of the wires guides the drops in a specific direction. Together, a self-sustained water-harvesting system is described which does not require additional external stimulus but makes use of a smart design and economic production.

To attach or not to attach? The effect of carrier surface morphology and topography on attachment of phoretic deutonymphs of Uropoda orbicularis (Acari)

Previous studies on preferences of phoretic deutonymphs of Uropodina for attachment sites have shown that they frequently select smooth and hydrophobic surfaces. The aim of our study was to provide the detailed morphological and topographical characteristics of beetle body surfaces to which deutonymphs frequently attach and to verify how the presence of setae and surface sculpture affects deutonymph attachment. The study was conducted on Uropoda orbicularis (Müller, 1776) and its common beetle carriers: Aphodius prodromus (Brahm, 1790), Aphodius fimetarius (Linnaeus, 1758), Onthophagus nuchicornis (Linnaeus, 1758) and Margarinotus carbonarius (Hoffmann, 1803). Morphology and topography of elytra, femora, propygidia and pygidia of beetles were analysed mainly using SEM methods supported with CLSM and AFM techniques. The hypothesis that deutonymphs may attach to surfaces covered with setae, if seta density is low enough not to disturb mite movement, was tested. The study revealed that deutonymphs attach to surfaces of various types as follows: (i) smooth, (ii) hairy, i.e., covered with setae, (iii) flat and (iv) sculptured. Smooth body parts and body parts covered with setae of low density were most frequently and intensively occupied with deutonymphs. Surfaces of high seta density were avoided by mites. Within elytra of Aphodius beetles, deutonymphs definitely preferred flat surfaces of elytral intervals. On the contrary, densely punctuated propygidium and pygidium in M. carbonarius were heavily infested with deutonymphs. We conclude that carrier surface morphology and topography are important for Uropodina deutonymph attachment, but these two factors cannot fully explain the observed relation.

No Effects and No Control of Epibionts in Two Species of Temperate Pycnogonids

Essentially all surfaces of marine plants and animals host epibionts. These organisms may harm their hosts in a number of ways, including impeding gas exchange or increasing the costs of locomotion. Epibionts can also be beneficial. For example, they may camouflage their hosts, and photosynthetic epibionts can produce oxygen. In general, however, the costs of epibionts appear to outweigh their benefits. Many organisms, therefore, shed epibionts by grooming, molting, or preventing them from initially attaching, using surface waxes and cuticular structures. In this study, we examined how epibionts affect local oxygen supply to temperate species of pycnogonids (sea spiders). We also tested the effectiveness of different methods that pycnogonids may use to control epibionts (grooming, cuticle wettability, and cuticular waxes). In two temperate species: Achelia chelata and Achelia gracilipes, epibionts consisted primarily of algae and diatoms, formed layers approximately 0.25-mm thick, and they colonized at least 75% of available surface area. We used microelectrodes to measure oxygen levels in and under the layers of epibionts. In bright light, these organisms produced high levels of oxygen; in the dark, they had no negative effect on local oxygen supply. We tested mechanisms of control of epibionts by pycnogonids in three ways: disabling their ovigers to prevent grooming, extracting wax layers from the cuticle, and measuring the wettability of the cuticle; however, none of these experiments affected epibiont coverage. These findings indicate that in temperate environments, epibionts are not costly to pycnogonids and, in some circumstances, they may be beneficial.

Liquid-induced colour change in a beetle: the concept of a photonic cell

The structural colour of male Hoplia coerulea beetles is notable for changing from blue to green upon contact with water. In fact, reversible changes in both colour and fluorescence are induced in this beetle by various liquids, although the mechanism has never been fully explained. Changes enacted by water are much faster than those by ethanol, in spite of ethanol's more rapid spread across the elytral surface. Moreover, the beetle's photonic structure is enclosed by a thin scale envelope preventing direct contact with the liquid. Here, we note the presence of sodium, potassium and calcium salts in the scale material that mediate the penetration of liquid through putative micropores. The result leads to the novel concept of a "photonic cell": namely, a biocompatible photonic structure that is encased by a permeable envelope which mediates liquid-induced colour changes in that photonic structure. Engineered photonic cells dispersed in culture media could revolutionize the monitoring of cell-metabolism.

Hyperspectral interferometry: Sizing microscale surface features in the pine bark beetle

A new method of interferometry employing a Fabry-Perot etalon model was used to locate and size microscale features on the surface of the pine bark beetle. Oscillations in the reflected light spectrum, caused by self-interference of light reflecting from surfaces of foreleg setae and spores on the elytrum, were recorded using white light hyperspectral microscopy. By making the assumption that pairs of reflecting surfaces produce an etalon effect, the distance between surfaces could be determined from the oscillation frequency. Low frequencies of less than 0.08 nm(-1) were observed in the spectrum below 700 nm while higher frequencies generally occupied wavelengths from 600 to 850 nm. In many cases, two frequencies appeared separately or in combination across the spectrum. The etalon model gave a mean spore size of 3.04 ± 1.27 μm and a seta diameter of 5.44 ± 2.88 μm. The tapering near the setae tip was detected as a lowering of frequency. Spatial fringes were observed together with spectral oscillations from surfaces on the exoskeleton at higher magnification. These signals were consistent with embedded multi-layer reflecting surfaces. Possible applications for hyperspectral interferometry include medical imaging, detection of spore loads in insects and other fungal carriers, wafer surface and subsurface inspection, nanoscale materials, biological surface analysis, and spectroscopy calibration. This is, to our knowledge, the first report of oscillations directly observed by microscopy in the reflected light spectra from Coleoptera, and the first demonstration of broadband hyperspectral interferometry using microscopy that does not employ an internal interferometer.

Nanomechanical properties of wing membrane layers in the house cricket (Acheta domesticus Linnaeus)

Many insect wings change shape dynamically during the wingbeat cycle, and these deformations have the potential to confer energetic and aerodynamic benefits during flight. Due to the lack of musculature within the wing itself, the changing form of the wing is determined primarily by its passive response to inertial and aerodynamic forces. This response is in part controlled by the wing's mechanical properties, which vary across the membrane to produce regions of differing stiffness. Previous studies of wing mechanical properties have largely focused on surface or bulk measurements, but this ignores the layered nature of the wing. In our work, we investigated the mechanical properties of the wings of the house cricket (Acheta domesticus) with the aim of determining differences between layers within the wing. Nanoindentation was performed on both the surface and the interior layers of cross-sectioned samples of the wing to measure the Young's modulus and hardness of the outer- and innermost layers. The results demonstrate that the interior of the wing is stiffer than the surface, and both properties vary across the wing.

Natural insect and plant micro-/nanostructsured surfaces: an excellent selection of valuable templates with superhydrophobic and self-cleaning properties

Insects and plants are two types of organisms that are widely separated on the evolutionary tree; for example, plants are mostly phototrophic organisms whilst insects are heterotrophic organisms. In order to cope with environmental stresses, their surfaces have developed cuticular layers that consist of highly sophisticated structures. These structures serve a number of purposes, and impart useful properties to these surfaces. These two groups of organisms are the only ones identified thus far that possess truly superhydrophobic and self-cleaning properties. These properties result from their micro- and nano-scale structures, comprised of three-dimensional wax formations. This review analyzes the surface topologies and surface chemistry of insects and plants in order to identify the features common to both organisms, with particular reference to their superhydrophobic and self-cleaning properties. This information will be valuable when determining the potential application of these surfaces in the design and manufacture of superhydrophobic and self-cleaning devices, including those that can be used in the manufacture of biomedical implants.

Sex-related effects in the superhydrophobic properties of damselfly wings in young and old Calopteryx splendens

Numerous sex-related morphological adaptations are connected to reproductive behavior in animals. For example, females of some insect species can submerge during oviposition, which may lead to sex-related adaptations in the hydrophobicity (water-repellency) due to specialization of certain morphological structures. On the other hand, ageing can cause changes in hydrophobicity of the surface, because the morphological structures can wear with age. Here, we investigated sex-and age-related differences in wing hydrophobicity and in morphology (spine density, wax cover characteristics, size of females' pseudopterostigma) potentially related to hydrophobicity of Calopteryx splendens damselflies. Hydrophobicity was measured with two methods, by measuring the contact angle (CA) between a wing and water droplet, and by dipping a wing into water and measuring forces needed to submerge, withdraw, and pull-out a wing from water. We found that C. splendens wings are superhydrophobic, having mean CAs of 161°. The only sex and age related difference in the hydrophobicity measurements was that young females had stronger amplitude of force fluctuations during withdrawal of wings from water than young males. This suggests that young females may form less uniform air pockets on their wings while submerged. From the morphological structures measured here, the only sex related finding was that old females had denser spine cover than young females in their wing veins. The difference may be explained by better survival of females with denser spine cover. The most important morphological character that predicted superhydrophobicity was the prevalence of long wax rods on wing veins. In addition, female pseudopterostigma area (a trait present only in females) was negatively related to pull-out force, suggesting that large pseudopterostigmas might help females to emerge from water following oviposition. The subtle sex-related differences in hydrophobicity could be explained by the fact that both sexes must resist rain, and males are occasionally in contact with water.

Microstructure and Wettability on the Elytral Surface of Aquatic Beetle

The microstructures on elytral surface of aquatic beetles belonging to Hydrophilidae and Dytiscidae were observed under an environment scanning microscope, and the wettabilities were determined with an optical contact angle meter. The results show the elytral surfaces are relatively smooth compared to the structures of other insects such as the butterfly wing scales or cicada wing protrusions. They exhibit a polygonal structuring with grooves and pores being the main constituent units. The contact angles (CAs) range from 47.1oto 82.1o. The advancing and receding angles were measured by injecting into and withdrawing a small amount of water on the most hydrophilic (with a contact angle of 47.1o) and hydrophobic (with a contact angle of 82.1o) elytral surfaces, which illustrates the vital role of three-phase contact line (TCL) in the wetting mechanism of aquatic beetle elytral surfaces.

Molecular organization of the nanoscale surface structures of the dragonfly Hemianax papuensis wing epicuticle

The molecular organization of the epicuticle (the outermost layer) of insect wings is vital in the formation of the nanoscale surface patterns that are responsible for bestowing remarkable functional properties. Using a combination of spectroscopic and chromatographic techniques, including Synchrotron-sourced Fourier-transform infrared microspectroscopy (FTIR), x-ray photoelectron spectroscopy (XPS) depth profiling and gas chromatography-mass spectrometry (GCMS), we have identified the chemical components that constitute the nanoscale structures on the surface of the wings of the dragonfly, Hemianax papuensis. The major components were identified to be fatty acids, predominantly hexadecanoic acid and octadecanoic acid, and n-alkanes with even numbered carbon chains ranging from C14 to C30. The data obtained from XPS depth profiling, in conjunction with that obtained from GCMS analyses, enabled the location of particular classes of compounds to different regions within the epicuticle. Hexadecanoic acid was found to be a major component of the outer region of the epicuticle, which forms the surface nanostructures, and was also detected in deeper layers along with octadecanoic acid. Aliphatic compounds were detected throughout the epicuticle, and these appeared to form a third discrete layer that was separate from both the inner and outer epicuticles, which has never previously been reported.