A Review of Weathering Studies in Plastics and Biocomposites-Effects on Mechanical Properties and Emissions of Volatile Organic Compounds (VOCs)

Polymeric materials undergo degradation when exposed to outdoor conditions due to the synergistic effects of sunlight, air, heat, and moisture. The degradation can lead to a decline in mechanical properties, fading, surface cracking, and haziness, attributed to the cleavage of the polymer chains and oxidation reactions. Accelerated weathering testing is a useful technique to evaluate the comparative photodegradation of materials within a reasonable timeframe. This review gives an overview of the different degradation mechanisms occurring in conventional plastics and bio-based materials. Case studies on accelerated weathering and its effect on the mechanical properties of conventional plastics and biocomposites are discussed. Different techniques for analysing volatile organic emissions (VOCs) have been summarized and studies highlighting the characterization of VOCs from aged plastics and biocomposites after aging have been cited.

Improved matrix purification using a graphene oxide-coated melamine sponge for UPLC-MS/MS-based determination of 37 veterinary drugs in milks

A rapid and highly sensitive method was established for the analysis of 37 veterinary drug residues in milk using a modified QuEChERS method based on a reduced graphene oxide-coated melamine sponge (rGO@MeS) coupled with UPLC-MS/MS. Under optimal chromatographic and mass spectrometric conditions, the effects of different dehydrated salts (MgSO4 and Na2SO4) and metal chelating agents (Na2EDTA) on extraction efficiency were first investigated. Next, the influence of a dynamic and static purification mode was evaluated in terms of drug recoveries. Calibration curves of 37 veterinary drugs were constructed in the range 0.6-500 μg kg-1, and good linearities were obtained with all determination coefficients (R2) ≥0.992. The limits of detection (LODs) and quantitation (LOQs) were in the range 0.3-1.1 μg kg-1 and 0.6-3.5 μg kg-1, respectively. The recoveries of all compounds were in the range 61.3-118.2% at three spiked levels (20, 100, and 200 μg kg-1) with RSDs ≤15.4% for both intra- and inter-day precisions. Compared to pristine melamine sponges and commercial adsorbents (C18, PSA, and GCB), rGO@MeS demonstrated an equal or even better purification performance in terms of recoveries, matrix effects, and matrix removal efficiency. This method is rapid, simple, efficient, and appropriate for the qualitative and quantitative analyses of 37 veterinary drug residues in milk, providing a new detection strategy and technical support for the routine analysis of animal-derived food.

Application of hollow fiber-protected liquid-phase microextraction combined with GC-MS in determining Endrin, Chlordane, and Dieldrin in rice samples

This paper introduces a novel and minimized sample preparation technique based on hollow fiber-protected liquid-phase microextraction that can be used in joint with gas chromatography-mass spectrometry (GC-MS) detection to extract three organochlorine pesticides-Endrin, Chlordane, and Dieldrin-from rice samples. To that end, a single-walled carbon nanotube (SWCNT) and a proper ionic liquid (IL) were ultrasonically dispersed and injected into the lumen of hollow fiber as the extraction phase for preconcentrating and extracting the target analytes from the rice samples. The effects of the type of nanoparticles, ILs, and desorption solvent on the efficiency of extracting the analytes were investigated based on the one-factor-at-a-time (OFAT) approach. In addition, other parameters influencing the extraction procedure were optimized using an experimental design that decreased the number of experiments, reagent consumption, and costs. Under optimized conditions, the limits of detection and quantification in determining mentioned pesticides varied between 0.019-0.029 and 0.064-0.098 ng mL-1, respectively. The calibration graphs to measure Endrin, Chlordane, and Dieldrin were linear over the concentration range of 0.064-13.2, 0.098-16.7, and 0.092-11.4 ng mL-1, respectively. The relative standard deviations for inter-day and intra-day analysis were below 7.06 and 4.75% for the triplicate determination of three organochlorine pesticides. Besides, the relative recoveries and standard deviations of Endrin, Chlordane, and Dieldrin for analyzing several Iranian rice samples were between 86.0-92.9% and 4.5-5.8%, respectively. The results were compared with other similar works in literature, proving that the proposed method is efficient and useful for routine monitoring of organochlorine compounds in food samples.

Synthesis and Surface Modification of Iron Oxide Nanoparticles for the Extraction of Cadmium Ions in Food and Water Samples: A Chemometric Study

In this project, a prompt, efficient, and effective method for Cd2+ ions extraction from different food and water samples using magnetic dispersion-based solid phase extraction by functionalized iron oxide nanoparticles was proposed. Iron oxide nanoparticles were synthesized through the co-precipitation method followed by functionalization with tetraethyl orthosilicate (TEOS) and 3-aminopropyl silane (APTES) to obtain Fe3O4@SiO2@APTES. This composite was characterized through different techniques, including vibrating sample magnetometer, dynamic light scattering, zeta potential, FTIR, SEM, XRD, and BET. Variables studied were pH, temperature, sorbent amount, sonication time, and sample and eluent volume affecting the sorption efficacy of freshly synthesized sorbent. Plackett–Burman design was utilized for the identification of significant factors for microextraction of target analyte, while the central composite design was utilized for the optimization of significant factors. Detection and quantification limits obtained were 0.17 and 0.58 μgL−1, respectively, with an enhancement factor of 83.5. Under optimum conditions, Fe3O4@SiO2@APTES showed good stability even after >80 adsorption/desorption cycles run while maintaining over 96% analyte recoveries. The developed method was validated by assessing certified reference materials and standard addition methodology for Cd2+ detection in real samples. To confirm the precision, repeatability (RSDr) and reproducibility (RSDR) were calculated and found as <3.0 (n = 7) and <7.5 (n = 15), respectively. Furthermore, in accordance with the ISO/IEC 17025 recommendations, the validation was also confirmed through a “bottom-up” approach while considering all possible uncertainties in data.

Antibiotic resistance in the aquatic environment: Analytical techniques and interactive impact of emerging contaminants

Antibiotic pollution is becoming an increasingly severe threat globally. Antibiotics have emerged as a new class of environmental pollutants due to their expanding usage and indiscriminate application in animal husbandry as growth boosters. Contamination of aquatic ecosystems by antibiotics can have a variety of negative impacts on the microbial flora of these water bodies, as well as lead to the development and spread of antibiotic-resistant genes. Various strategies for removing antibiotics from aqueous systems and environments have been developed. Many of these approaches, however, are constrained by their high operating costs and the generation of secondary pollutants. This review aims to summarize research on the distribution and effects of antibiotics in aquatic environments, their interaction with other emerging contaminants, and their remediation strategy. The ecological risks associated with antibiotics in aquatic ecosystems and the need for more effective monitoring and detection system are also highlighted.

Simultaneous determination of furosemide and carbamazepine in biological matrices by solvent bar microextraction combined with HPLC-DAD and central composite design CCD

A sensitive and simple sample pretreatment method based on a two-phase solvent bar microextraction SBME technique coupled with HPLC-DAD was developed for simultaneous extraction and determination of trace amounts of furosemide and carbamazepine in human urine and plasma samples. The significance of operational factors on carbamazepine and furosemide extraction efficiency % (EE%) was screened using full factorial design (FFD) while central composite design (CCD) was used to model the entire process. A quadratic model was found convenient to correlate the extraction EE% of selected drugs with dominant experimental factors. A Pareto chart was also used to examine the importance of factors on drugs' EE%. The analytical performance of the method in urine and plasma samples demonstrated good linearity R² ˃ 0.992 with detection limits ranging from 4.2 to 10.9 μg L^-1 , and extraction recovery ˃ 89.45% for both drugs in urine and plasma samples. A comparison against published methods was also studied and the results revealed that the developed method exhibits a confident sensitivity, feasible operation, and simple analysis for both drugs. Finally, the practicability of the validated SBME-HPLC-DAD method was demonstrated by successfully applying it to the analysis of furosemide, and carbamazepine in real patient urine samples.

Overview of Different Modes and Applications of Liquid Phase-Based Microextraction Techniques

Liquid phase-based microextraction techniques (LPµETs) have attracted great attention from the scientific community since their invention and implementation mainly due to their high efficiency, low solvent and sample amount, enhanced selectivity and precision, and good reproducibility for a wide range of analytes. This review explores the different possibilities and applications of LPμETs including dispersive liquid–liquid microextraction (DLLME) and single-drop microextraction (SDME), highlighting its two main approaches, direct immersion-SDME and headspace-SDME, hollow-fiber liquid-phase microextraction (HF-LPME) in its two- and three-phase device modes using the donor–acceptor interactions, and electro membrane extraction (EME). Currently, these LPμETs are used in very different areas of interest, from the environment to food and beverages, pharmaceutical, clinical, and forensic analysis. Several important potential applications of each technique will be reported, highlighting its advantages and drawbacks. Moreover, the use of alternative and efficient “green” extraction solvents including nanostructured supramolecular solvents (SUPRASs, deep eutectic solvents (DES), and ionic liquids (ILs)) will be discussed.

Advanced Solid-Phase Microextraction Techniques and Related Automation: A Review of Commercially Available Technologies

The solid-phase microextraction (SPME), invented by Pawliszyn in 1989, today has a renewed and growing use and interest in the scientific community with fourteen techniques currently available on the market. The miniaturization of traditional sample preparation devices fulfills the new request of an environmental friendly analytical chemistry. The recent upswing of these solid-phase microextraction technologies has brought new availability and range of robotic automation. The microextraction solutions propose today on the market can cover a wide variety of analytical fields and applications. This review reports on the state-of-the-art innovative solid-phase microextraction techniques, especially those used for chromatographic separation and mass-spectrometric detection, given the recent improvements in availability and range of automation techniques. The progressively implemented solid-phase microextraction techniques and related automated commercially available devices are classified and described to offer a valuable tool to summarize their potential combinations to face all the laboratories requirements in terms of analytical applications, robustness, sensitivity, and throughput.

Metabolomics-Guided Elucidation of Plant Abiotic Stress Responses in the 4IR Era: An Overview

Plants are constantly challenged by changing environmental conditions that include abiotic stresses. These are limiting their development and productivity and are subsequently threatening our food security, especially when considering the pressure of the increasing global population. Thus, there is an urgent need for the next generation of crops with high productivity and resilience to climate change. The dawn of a new era characterized by the emergence of fourth industrial revolution (4IR) technologies has redefined the ideological boundaries of research and applications in plant sciences. Recent technological advances and machine learning (ML)-based computational tools and omics data analysis approaches are allowing scientists to derive comprehensive metabolic descriptions and models for the target plant species under specific conditions. Such accurate metabolic descriptions are imperatively essential for devising a roadmap for the next generation of crops that are resilient to environmental deterioration. By synthesizing the recent literature and collating data on metabolomics studies on plant responses to abiotic stresses, in the context of the 4IR era, we point out the opportunities and challenges offered by omics science, analytical intelligence, computational tools and big data analytics. Specifically, we highlight technological advancements in (plant) metabolomics workflows and the use of machine learning and computational tools to decipher the dynamics in the chemical space that define plant responses to abiotic stress conditions.

Determination of pyridaphenthion in soybean sprout samples by gas chromatography mass spectrometry with matrix matching calibration strategy after metal sieve linked double syringe based liquid-phase microextraction

A novel analytical strategy for the trace determination of pyridaphenthion pesticide was developed in this study. Gas chromatography-mass spectrometry (GC-MS) was used for the accurate, feasible and precise determination of this analyte. Liquid phase microextraction (LPME) was performed with a metal sieve linked double syringe (MSLDS) system, which eliminated the need for a disperser solvent. In order to increase extraction efficiency for the analyte, all variable parameters were optimized and the system analytical performance of the proposed method was determined. Limit of detection and quantification (LOD and LOQ) values of pyridaphenthion were found to be 0.8 and 2.7 µg L-1, respectively. Compared to GC-MS system's analytical performance, the developed method provided approximately 273-folds improvement in the detection limit of the analyte. Applicability/accuracy of the developed analytical strategy was checked by recovery experiments carried out with soybean sprouts, and the results obtained were satisfactory.

A review of micro-solid-phase extraction techniques and devices applied in sample pretreatment coupled with chromatographic analysis

Sample pretreatment is one of the most crucial and error-prone steps of an analytical procedure; it consents to improve selectivity and sensitivity by sample clean-up and pre-concentration. Nowadays, the arousing interest in greener and sustainable analytical chemistry has increased the development of microextraction techniques as alternative sample preparation procedures. In this review, we aimed to show two different categorizations of the most used micro-solid-phase extraction (μSPE) techniques. In essence, the first one concerns the solid-phase extraction (SPE) sorbent selection and structure: normal-phase, reversed-phase, ion-exchange, mixed-mode, molecular imprinted polymer, and special techniques (e.g., doped cartridges for specific analytes). The second is a grouping of the commercially available μSPE products in categories and sub-categories. We present every device and technology into the classifications paying attention to their historical development and the actual state of the art. So, this study aims to provide the state-of-the-art of μSPE techniques, highlighting their advantages, disadvantages, and possible future developments in sample pretreatment.

Solvent bar microextraction combined with HPLC-DAD for simultaneous determination of diuretics in human urine and plasma samples

BACKGROUND

A simple and powerful microextraction procedure, the solvent bar microextraction (SBME), was used for the simultaneous determination of two diuretics, furosemide and spironolactone in human urine and plasma samples, using high-performance liquid chromatography coupled with diode array detection (HPLC-DAD).

METHODS

The appropriate amount (2 µL) of 1-octanol as an organic solvent confined within (2.5 cm) of a porous hollow fiber micro-tube, sealed at both ends was used for this procedure. The conditions for the SBME were optimized in water and the analytical performance were examined in spiked human urine and plasma samples.

RESULTS

The optimized method exhibited good linearity (R2 > 0.997) over the studied range of higher than 33 to 104 µg L-1 for furosemide and spironolactone in urine and plasma samples, illustrating a satisfactory precision level with RSD values between 2.1% and 9.1%.

DISCUSSION

The values of the limits of detection were found to be in the range of 6.39 to 9.67 µg L-1, and extraction recovery˃ 58.8% for both diuretics in urine and plasma samples. The applicability and effectiveness of the proposed method for the determination of furosemide and spironolactone in patient urine samples were tested.

CONCLUSION

In comparison with reference methods, the attained results demonstrated that SBME combined with HPLC-DAD was proved to be simple, inexpensive, and promising analytical technology for the simultaneous determination of furosemide and spironolactone in urine and plasma samples.

A fast-multiclass method for the determination of 21 endocrine disruptors in human urine by using vortex-assisted dispersive liquid-liquid microextraction (VADLLME) and LC-MS/MS

Simplicity, speed, and reduced cost are essential demands for routine analysis in human biomonitoring studies. Moreover, the availability of higher volumes of human specimens is becoming more restrictive due to ethical controls and to the costs associated with sample transportation and storage. Thus, analytical methods requiring much lower sample volumes associated with simultaneous detection capability (multiclass analysis) are with a very high claim. In this sense, the present approach aimed at the development of a method for preconcentration and simultaneous determination of four classes of endocrine disruptors (seven bisphenols, seven parabens, five benzophenones, and two antimicrobials) in the urine. The approach is based on vortex-assisted dispersive liquid-liquid microextraction (VADLLME) and high-performance liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS). After optimization of the significant parameters of VADLLME extraction, the proposed procedure showed to be simple, fast, sensitive, requiring only 1.0 mL of urine, 400 μL of organic solvents with a total stirring time of 20 s. Moreover, a variation of inter-day and between-day runs were lower than 10.0% and 11.0%, respectively. Finally, the proposed method was successfully applied to the analysis of 50 urine samples of Brazilian pregnant women to establish reference ranges.