Prospective evaluation of 2,549 Morse taper connection implants: 1- to 6-year data

Stress-strain and fatigue life numerical evaluation of two different dental implants considering isotropic and anisotropic human jaw

Dental prostheses are currently a valid solution for replacing potential missing tooth or edentulism clinical condition. Nevertheless, the oral cavity is a dynamic and complex system: occlusal loads, external agents, or other unpleasant events can impact on implants functionality and stability causing a future revision surgery. One of the failure origins is certainly the dynamic loading originated from daily oral activities like eating, chewing, and so on. The aim of this paper was to evaluate, by a numerical analysis based on Finite Elements Method (FEM), and to discuss in a comparative way, firstly, the stress-strain of two different adopted dental implants and, subsequently, their fatigue life according to common standard of calculations. For this investigation, the jawbone was modeled accounting for either isotropic or anisotropic behavior. It was composed of cortical and cancellous regions, considering it completely osseointegrated with the implants. The impact of implants' fixture design, loading conditions, and their effect on the mandible bone was finally investigated, on the basis of the achieved numerical results. Lastly, the life cycle of the investigated implants was estimated according to the well-established theories of Goodman, Soderberg, and Gerber by exploiting the outcomes obtained by the numerical simulations, providing interesting conclusions useful in the dental practice.

Evaluation of Removal Force in Prosthetic Components of Morse Taper Dental Implants

The longevity of prosthetic rehabilitation is determined by the stability of the implant and abutment interfaces. True morse taper connections on dental restorations have been effective, however activation force still empirical. This work compared the activation strength and internal contact of Morse taper system according to the removal force. Eighty sets, composed of implants and prosthetic abutments, were evaluated with different internal contact areas; 15.12mm2 (G3.3) and 21.25mm2 (G4.3). The specimens were activated at 0° and 30°, with loads of 10, 20, 40 and 60N. The specimens were submitted to tensile test and the data to ANOVA and Tukey's tests (α=0.05). Representative specimens were examined under SEM. Removal force of G3.3 (2.15±1.33MPa) did not differed to G4.3 (1.99±1.03MPa). The activation at 0º (2.95±0.98MPa) statistically differed to 30º (1.19±0.54MPa). The 60N load was statistically superior for G3.3 and there was no statistical difference between 20N to 60N in G4.3. The values of 10N at 30o and 20N at the long axis of the morse taper implant, independent of the frictional contact area showed the best settlement.

Effects of Osseodensification on Immediate Implant Placement: Retrospective Analysis of 211 Implants

Osseodensification is a new method of bone instrumentation for dental implant placement that preserves bulk bone and increases primary implant stability, and may accelerate the implant rehabilitation treatment period and provide higher success and survival rates than conventional methods. The aim of this retrospective study was to evaluate and discuss results obtained on immediate implant placement with immediate and delayed loading protocols under Osseodensification bone instrumentation. This study included private practice patients that required dental implant rehabilitation, between February 2017 and October 2019. All implants were placed under Osseodensification and had to be in function for at least 12 months to be included on the study. A total of 211 implants were included in the study, with a 98.1% total survival rate (97.9% in the maxilla and 98.5% in the mandible). For immediate implants with immediate load, 99.2% survival rate was achieved, and 100% survival rate for immediate implant placement without immediate load cases. A total of four implants were lost during this period, and all of them were lost within two months after placement. Within the limitations of this study, it can be concluded that Osseodensification bone instrumentation provided similar or better results on survival rates than conventional bone instrumentation.

Implant supported cantilevered fixed dental rehabilitations in partially edentulous patients: Systematic review of the literature. Part I

OBJECTIVES

To investigate in which clinical situations a cantilever fixed implant supported restorations can be a treatment alternative and which complications are reported.

MATERIALS AND METHODS

Two operators screened the literature (MEDLINE, EMBASE) and performed a hand search on the main journals dealing with implantology and prosthetics until 31 December 2017. Only articles that considered cantilever implant fixed restorations with at least 10 patients and with a mean follow-up of at least 5 year were selected. The outcome variables were survival of implants and prosthesis, mechanical, technical and biological complications, marginal bone loss. The review was performed according to the PRISMA statements. Risk of bias assessment was evaluated. Failure and complication rates were analysed using random effect Poisson regression models to obtain summary estimate of 5- and 10-year survival and complication rates.

RESULTS

A total of nine papers were selected for partially edentulous patients and reported high survival rate of the prosthesis. The estimated survival rate for 5-10 years was calculated to be 98.4% for the implants and 99.2% for the rehabilitations. Mechanical, technical and biological complications were reported with a cumulative 5-10 years complication rate of 28.66% and 26.57% for the patients and for the prosthesis, respectively. Two papers for single implant supporting 2-unit cantilever were not sufficient to draw conclusions.

CONCLUSIONS

There is evidence that cantilever can be successful treatment in partially edentulous patients. In two adjacent edentulous sites, data are not yet sufficient.

A Novel Full-Digital Protocol (SCAN-PLAN-MAKE-DONE®) for the Design and Fabrication of Implant-Supported Monolithic Translucent Zirconia Crowns Cemented on Customized Hybrid Abutments: A Retrospective Clinical Study on 25 Patients

Purpose: To present a novel, full-digital protocol for the design and fabrication of implant-supported monolithic translucent zirconia crowns cemented on customized hybrid abutments. Methods: The present retrospective clinical study was based on data from patients who had been treated with single Morse-taper connection implants (Exacone^®, Leone Implants, Florence, Italy) and were prosthetically restored with monolithic translucent zirconia crowns, cemented on customized hybrid abutments. The full-digital protocol (SCAN-PLAN-MAKE-DONE^®) consisted of 8 phases: (1) intraoral scan of the implant position with scanbody; (2) computer-assisted design (CAD) of the individual abutment (saved as “supplementary abutment design” in external folder) and temporary crown; (3) milling of the individual zirconia abutment and of the temporary polymethyl-methacrylate (PMMA) crown, with extraoral cementation of the zirconia abutment on the relative titanium bonding base, to generate an individual hybrid abutment; (4) clinical application of the individual hybrid abutment and cementation of the temporary PMMA crown; (5) two months later, intraoral scan of the individual hybrid abutment in position; (6) CAD of the final crown with margin line design on the previously saved “supplementary abutment design”, superimposed on the second scan of the abutment in position; (7) milling of the final crown in monolithic translucent zirconia, sintering, and characterization; and (8) clinical application of the final crown. All patients were followed for a period of 1 year. The primary outcomes of this study were the marginal adaptation of the final crown (checked clinically and radiographically), the quality of occlusal and interproximal contact points at delivery, and the aesthetic integration; the secondary outcomes were the 1-year survival and success of the implant-supported restoration. An implant-supported restoration was considered successful in the absence of any biological or prosthetic complication, during the entire follow-up period. Results: In total, 25 patients (12 males, 13 females; 26–74 years of age; mean age 51.1 ± 13.3 years) who had been restored with 40 implant-supported monolithic translucent zirconia crowns were included in this study. At delivery, the marginal adaptation was perfect for all crowns. However, there were occlusal issues (2/40 crowns: 5%), interproximal issues (1/40 crowns: 2.5%), and aesthetic issues (1/40 crowns: 2.5%). The overall incidence of issues at delivery was therefore 10% (4/40 crowns). At 1 year, one implant failed; thus the survival of the restorations was 97.5% (39/40 crowns in function). Among the surviving implant-supported restorations, three experienced complications (one loss of connection between the hybrid abutment and the implant, one decementation of the zirconia abutment, and one decementation of the zirconia crown). The success of restorations amounted to 92.4%. Conclusions: The restoration of single Morse-taper connection implants with monolithic translucent zirconia crowns cemented on customized hybrid abutments via the novel SCAN-PLAN-MAKE-DONE^® full-digital protocol seems to represent a reliable treatment option. However, further studies on a larger number of patients and dealing with different prosthetic restorations (such as implant-supported fixed partial prostheses) are needed to confirm the validity of this protocol.

Morse taper implant macrodesign, loading protocol and site of installation – retrospective study of 5,601 implants

Abstract Introduction The long-term implant-supported prosthetic rehabilitation monitoring is extremely important in evaluating parameters that could interfere in the success of the treatment. Objective To evaluate the influence of macrodesign (shape of the body and apex), length and diameter, insertion torque, site of installation as well as the loading protocol, on long-term survival rates. Material and method The data obtained was from the medical records of rehabilitated patients who had had at least one Morse taper implant surgery done at ILAPEO School between 2006 -2012. Incomplete medical records, from which it would have been impossible to extract all data essential to complete the study, were excluded. Result A total of 1,142 patient’s medical records comprised the sample; documenting the progress of 5,601 implants, done in both jaws and mandibles. The final survival rate was 98.31%, over an average time of 37.54 months. The type of implant most used was cylindrical (70.33%). The mean installation torque most evidenced in the study was between 41 and 50 Ncm. A logistical regression analysis showed that none of the following variables, site of installation, body and apex shape designs and length, had any significant statistical influence on implant loss. Torque increase and diameter influenced implant loss while immediate loading favored implant maintenance. Conclusion It can be concluded that Morse taper implants present a long-term survival rate that can be lowered by excessive torque, as well as by the diameter of the implant.

Combination Use of BMP2 and VEGF165 Promotes Osseointegration and Stability of Titanium Implants in Irradiated Bone

Background

Clinical data demonstrated that failure rate of titanium implant in irradiated bone was 2-3 times higher than that in nonirradiated bone and it is difficult to get the ideal results in irradiated bone.

Purpose

The aim of the study was to investigate the effects of HBO, BMP2, VEGF165, and combined use of BMP2/VEGF165 on osseointegration and stability of titanium implant in irradiated bone.

Materials and Methods

Sixty rabbits were randomly assigned to 5 groups (control group, HBO group, VEGF165 group, BMP2 group, and BMP2/VEGF165 group) after receiving 15 Gy radiation. Implant surgery was performed on tibias eight weeks later. They were sacrificed at two or eight weeks after operation. Implant stability, calcium, and ALP activity in serum, the ratio of bone volume to total volume, the rate of bone growth, and gene expression were assessed.

Result

There was no mortality and no implants failed during the experiment. Implant stability was significantly compromised in the control group compared to the other four experimental groups, and the BMP2/VEGF165 group had the highest implant stability. HBO, BMP2, and VEGF165 significantly increased BV/TV and the rate of bone growth, while the BMP2/VEGF165 showed the best effect among groups. The expression of RUNX2 in HBO, BMP2, and VEGF165/BMP2 group was higher than that in the VEGF165 and control groups at two weeks. The expression of OCN in HBO, BMP2, VEGF165, and VEGF165/BMP2 groups was higher than that in the control group, and the gene expression of CD31 was higher in HBO, VEGF165, and BMP2/VEGF165 groups than that in control and BMP2 groups.

Conclusion

HBO, BMP2, and VEGF165 could increase bone formation around the implant and improved the implant stability in irradiated bone. The combination use of BMP2 and VEGF165 may be promising in the treatment of implant patients with radiotherapy.

Bone Behavior in Relation to the Depth of the Line of Marginal Cementation of Prostheses on Morse Cone Implants: Radiographic Evaluation in a Dog Model

PURPOSE

This study was aimed at radiographically evaluating the effect of 3 different depths of the cementation line of prosthetic crowns on the bone response around Morse cone implants.

MATERIAL AND METHODS

Five dogs underwent extractions of the lower premolars; after 3 months, placement of 30 implants, 3 mm apical to the bone level, was performed. Prefabricated cylinders of alumina, used as abutments, with 3 different transmucosal extension were cemented to the implants with zinc oxide-eugenol cement, determining the depth of the cementation lines (1.5 mm apically, and 0.5 and 2.5 mm coronally, respectively, to the bone level). In the control group, implants and abutments were placed without crowns, therefore, with no cementation line.

RESULTS

The results showed no statistically significant differences between the control and test groups regarding the different depths of the cementation line both mesially (P = 0.18) and distally (P = 0.50).

CONCLUSION

Different depths of cementation did not affect the behavior of marginal bone, indicating that crowns can be cemented with zinc oxide-eugenol cement at any distance or even at the bone level without disturbing bone healing around Morse cone implants.

Is the internal connection more efficient than external connection in mechanical, biological, and esthetical point of views? A systematic review

PURPOSE

This systematic review aimed to evaluate if the internal connection is more efficient than the external connection and its associated influencing factors.

METHODS

A specific question was formulated according to the Population, Intervention, Control, and Outcome (PICO): Is internal connection more efficient than external connection in mechanical, biological, and esthetical point of views? An electronic search of the MEDLINE and the Web of Knowledge databases was performed for relevant studies published in English up to November 2013 by two independent reviewers. The keywords used in the search included a combination of "dental implant" and "internal connection" or "Morse connection" or "external connection." Selected studies were randomized clinical trials, prospective or retrospective studies, and in vitro studies with a clear aim of investigating the internal and/or external implant connection use.

RESULTS

From an initial screening yield of 674 articles, 64 potentially relevant articles were selected after an evaluation of their titles and abstracts. Full texts of these articles were obtained with 29 articles fulfilling the inclusion criteria. Morse taper connection has the best sealing ability. Concerning crestal bone loss, internal connections presented better results than external connections. The limitation of the present study was the absence of randomized clinical trials that investigated if the internal connection was more efficient than the external connection.

CONCLUSIONS

The external and internal connections have different mechanical, biological, and esthetical characteristics. Besides all systems that show proper success rates and effectiveness, crestal bone level maintenance is more important around internal connections than external connections. The Morse taper connection seems to be more efficient concerning biological aspects, allowing lower bacterial leakage and bone loss in single implants, including aesthetic regions. Additionally, this connection type can be successfully indicated for fixed partial prostheses and overdenture planning, since it exhibits high mechanical stability.

Maintenance periodontal therapy after systemic antibiotic and regenerative therapy of generalized aggressive periodontitis. A case report with 10-year follow-up

Aggressive periodontitis (AgP) is an inflammatory disease characterized by rapid attachment loss and bone destruction. This case report presents the 10-year results in a subject with generalized AgP treated by a regenerative periodontal therapeutic approach and the adjunctive use of antibiotics, following a systematic maintenance periodontal therapy. The use of enamel matrix derivatives (EMD) and adjunctive antibiotic therapy to treat AgP yielded improvements in clinical parameters and radiographic bony fill. This combined therapeutic approach following a systematic supportive periodontal therapy supports the long-term maintenance of teeth with previous advanced periodontal defects, demonstrating successful stability after 10-years follow-up. Clinical Relevance: The combined treatment protocol using EMD plus adjunctive antibiotic therapy, associated with a systematic supportive periodontal therapy, benefits the long-term maintenance of teeth with previous advanced periodontal defects in subjects presenting AgP, supporting this approach as an alternative in the treatment of AgP.

Strain analysis of different diameter Morse taper implants under overloading compressive conditions

The aim of this study was to evaluate the amount of deformation from compression caused by different diameters of Morse taper implants and the residual deformation after load removal. Thirty Morse taper implants lacking external threads were divided into 3 groups (n = 10) according to their diameter as follows: 3.5 mm, 4.0 mm and 5.0 mm. Two-piece abutments were fixed into the implants, and the samples were subjected to compressive axial loading up to 1500 N of force. During the test, one strain gauge remained fixed to the cervical portion of each implant to measure the strain variation. The strain values were recorded at two different time points: at the maximum load (1500 N) and 60 seconds after load removal. To calculate the strain at the implant/abutment interface, a mathematical formula was applied. Data were analyzed using a one-way Anova and Tukey's test (α = 0.05). The 5.0 mm diameter implant showed a significantly lower strain (650.5 μS ± 170.0) than the 4.0 mm group (1170.2 μS ± 374.7) and the 3.5 mm group (1388.1 μS ± 326.6) (p < 0.001), regardless of the load presence. The strain values decreased by approximately 50% after removal of the load, regardless of the implant diameter. The 5.0 mm implant showed a significantly lower strain at the implant/abutment interface (943.4 μS ± 504.5) than the 4.0 mm group (1057.4 μS ± 681.3) and the 3.5 mm group (1159.6 μS ± 425.9) (p < 0.001). According to the results of this study, the diameter influenced the strain around the internal and external walls of the cervical region of Morse taper implants; all diameters demonstrated clinically acceptable values of strain.

Prosthetic failure in implant dentistry

Although osseointegrated dental implants have become a predictable and effective modality for the treatment of single or multiple missing teeth, their use is associated with clinical complications. Such complications can be biologic, technical, mechanical, or esthetic and may compromise implant outcomes to various degrees. This article presents prosthetic complications accompanied with implant-supported single and partial fixed dental prostheses.

Immediate restoration of fixed partial prostheses supported by one-piece narrow-diameter selective laser sintering implants: a 2-year prospective study in the posterior jaws of 16 patients

PURPOSE

Selective laser sintering (SLS) is a new technique that allows implants to be produced by annealing titanium powder microparticles in a focused laser beam, according to a computer-generated model. The aim of this study was to evaluate the survival and success rate of immediately restored 1-piece narrow-diameter SLS implants, placed in the posterior jaws, after 2 years of functional loading.

MATERIALS AND METHODS

At the 2-year follow-up examination, several parameters were assessed. Success criteria included absence of pain, suppuration, exudation, implant mobility; distance between the implant shoulder and the first visible bone-to-implant contact <2.0 mm; and absence of prosthetic complications.

RESULTS

Thirty-seven implants were placed in the posterior jaws (14 maxilla, 23 mandible) of 16 patients (9 males, 7 females). The prosthetic restorations comprised 16 immediately restored fixed partial prostheses. No implant failure occurred, resulting in a 100% survival rate. The implant success was 94.6%, and the mean distance between the implant shoulder and the first visible bone-to-implant contact (DIB) was 0.4 ± 0.3 mm.

CONCLUSIONS

This study supports the hypothesis that 1-piece narrow-diameter SLS implants can be used in fixed prosthetic rehabilitations in the posterior regions of both jaws with a predictable positive outcome.

Fixed restorations supported by Morse-taper connection implants: a retrospective clinical study with 10-20 years of follow-up

OBJECTIVES

Rehabilitation with implant-supported fixed prostheses is a predictable modality to restore lost function and esthetics; however, fixed restorations are subject to biological and prosthetic complications, which may represent a problem in the long-term. The aim of this study was to evaluate the long-term survival and complication rates of fixed restorations supported by Morse-taper connection implants.

MATERIALS AND METHODS

Between January 1992 and December 2002, 49 patients (age range 22-70 years), were included in this study. The restorations involved 58 fixed reconstructions (15 single crowns [SCS], 29 partial prostheses, 14 full-arches), supported by 178 Morse-taper connection implants with a follow-up ranging from 10 to 20 years. Outcomes such as implant survival, marginal bone loss, frequency of biological and prosthetic complications as well as "complication-free" survival of restorations were investigated.

RESULTS

The 20-year overall cumulative implant survival was 97.2%. A few biological (3.4%) and prosthetic (10.3%) complications were reported. The "complication-free" survival rate of restorations was 85.5%. No statistically significant differences were observed among patients' gender, age, smoking or parafunctional habits, prosthesis site and type.

CONCLUSIONS

Satisfactory "complication-free" survival rates can be achieved after 20 years for fixed restorations supported by Morse-taper connection implants, with minimal marginal bone loss and complications.

Survival and complication rates of fixed restorations supported by locking-taper implants: a prospective study with 1 to 10 years of follow-up

PURPOSE

The aim of this 10-year follow-up study was to evaluate the implant survival and complication rates of fixed restorations supported by locking-taper implants.

MATERIALS AND METHODS

Over a 10-year period (January 2002 to December 2011) all patients referred to a single private practice for treatment with fixed restorations (single crowns, SCs; fixed partial prostheses, FPPs; fixed full arches, FFAs) supported by dental implants were considered for inclusion in the study. At each annual follow-up session, clinical, radiographic, and prosthetic parameters were assessed. The surviving implant-supported restorations were defined as "complication free" in the absence of any biological or prosthetic (mechanical or technical) complication. The cumulative implant survival and the "complication-free" survival of fixed implant-supported restorations were identified using the Kaplan-Meier method. The Log-rank test was used to identify correlations between the study variables.

RESULTS

In total, 1494 locking-taper implants (727 maxilla, 767 mandible) were placed in 642 patients (356 males, 286 females). Nineteen implants (12 maxilla, 7 mandible) failed. Implant failures were attributed to lack of osseointegration (14 implants), peri-implantitis (4 implants), and mechanical overloading (1 implant). An overall 10-year cumulative implant survival rate of 98.7% (98.3% maxilla, 99.1% mandible) was found. The implant survival rates did not significantly differ with respect to implant location, position, bone type, implant length and diameter, and type of restorations. Among the surviving implant-supported restorations (478 SC, 242 FPP, 19 FFA), a few biological (11/739: 1.4%) and prosthetic (27/739: 3.6%) complications were reported. The incidence of mechanical complications was low (3/739: 0.4%), with three loosened abutments in three SCs (3/478: 0.6%), and no abutment fractures; technical complications were more frequent (24/739: 3.2%), with an incidence of decementation of 2.0% (SC 2.0%, FPP 1.6%, FFA 5.2%) and ceramic/veneer chipping/fracture of 1.2% (SC 0.0%, FPP 2.8%, FFA 10.5%). A 10-year cumulative "complication-free" survival of restorations of 88.6% (SC 91.7%, FPP 83.1%, FFA 73.8%) was reported. The complication rates differ significantly with respect to the type of restoration (p < 0.05).

CONCLUSIONS

Fixed restorations on locking-taper implants seem to be a successful procedure for the rehabilitation of partially and completely edentulous arches.

Reasons for failures of oral implants

This study reviews the literature regarding the factors contributing to failures of dental implants. An electronic search was undertaken including papers from 2004 onwards. The titles and abstracts from these results were read to identify studies within the selection criteria. All reference lists of the selected studies were then hand-searched, this time without time restrictions. A narrative review discussed some findings from the first two parts where separate data from non-comparative studies may have indicated conclusions different from those possible to draw in the systematic analysis. It may be suggested that the following situations are correlated to increase the implant failure rate: a low insertion torque of implants that are planned to be immediately or early loaded, inexperienced surgeons inserting the implants, implant insertion in the maxilla, implant insertion in the posterior region of the jaws, implants in heavy smokers, implant insertion in bone qualities type III and IV, implant insertion in places with small bone volumes, use of shorter length implants, greater number of implants placed per patient, lack of initial implant stability, use of cylindrical (non-threaded) implants and prosthetic rehabilitation with implant-supported overdentures. Moreover, it may be suggested that the following situations may be correlated with an increase in the implant failure rate: use of the non-submerged technique, immediate loading, implant insertion in fresh extraction sockets, smaller diameter implants. Some recently published studies suggest that modern, moderately rough implants may present with similar results irrespective if placed in maxillas, in smoking patients or using only short implants.

A Four-Year Survival Rate Multicenter Prospective Clinical Study on 377 Implants: Correlations Between Implant Insertion Torque, Diameter, and Bone Quality

The purpose of this study was to evaluate the survival rate and incidence of prosthetic complications in 377 implants with a double octagon connection. Furthermore, the correlations among implant dimensions (diameter and length), bone quality, and insertion torque were investigated. A 4-year multicenter prospective clinical study was designed to evaluate the survival rate of 377 dental implants inserted in 189 patients between January 2004 and April 2010. After an average follow-up of 46 months, the implant survival rate was 99.7%, and the incidence of complication was 0.53%. Moreover, insertion torque was statistically related in a significant way to implant diameter. The connection system seemed to reduce the risk that the prosthetic component screw would loosen. Within the limits of this study, it was observed that a wider diameter corresponded to a higher implant primary stability. Implant length did not seem to be critical in obtaining higher primary stability.

A systematic review of the survival and complication rates of implant-supported fixed dental prostheses (FDPs) after a mean observation period of at least 5 years

OBJECTIVES

The objective of this systematic review was to assess the 5- and 10-year survival of implant-supported fixed dental prostheses (FDPs) and to describe the incidence of biological and technical complications.

METHODS

An electronic Medline search complemented by manual searching was conducted to identify prospective and retrospective cohort studies and case series on FDPs with a mean follow-up time of at least 5 years. Patients had to have been examined clinically at the follow-up visit. Failure and complication rates were analyzed using standard and random-effects Poisson regression models to obtain summary estimates of 5-year and 10-year survival and complication rates.

RESULTS

The updated search provided 979 titles and 257 abstracts. Full-text analysis was performed for 90 articles resulting in a total 32 studies that met the inclusion criteria. Meta-analysis of these studies indicated an estimated survival of implants supporting FDPs of 95.6% after 5 years and 93.1% after 10 years. When machined surface implants were excluded from the analysis and only rough surface implants included, the survival rate increased to 97.2% after 5 years. The survival rate of implant-supported FDPs was 95.4% after 5 years and 80.1% after 10 years of function. When the analysis was done exclusively for metal-ceramic FDPs, hence the old gold-acrylic FDPs were excluded, the survival rate increased significantly. The survival rate of metal-ceramic implant-supported FDPs was 96.4% after 5 years and 93.9% after 10 years. Only 66.4% of the patients were free of any complications after 5 years. The most frequent complications over the 5-year observation period were fractures of the veneering material (13.5%), peri-implantitis and soft tissue complications (8.5%), loss of access hole restoration (5.4%), abutment or screw loosening (5.3%), and loss of retention of cemented FDPs (4.7%).

CONCLUSION

It may be concluded that implant-supported fixed dental prostheses (FDPs) are a safe and predictable treatment method with high survival rates. However, biological and technical complications were frequent (33.6%). To minimize the incidence of complications, dental professionals should make great effort in choosing reliable components and materials for implant-supported FDPs and the patients should be placed in well-structured maintenance system after treatment.

Systematic review of the survival rate and the incidence of biological, technical, and aesthetic complications of single crowns on implants reported in longitudinal studies with a mean follow-up of 5 years

OBJECTIVE

To assess the 5-year survival of implant-supported single crowns (SCs) and to describe the incidence of biological, technical, and aesthetic complications. The focused question was: What is the survival rate of implants supporting single crowns and implant-supported crowns with a mean follow-up of 5 years and to which extent do biological, technical, and aesthetic complications occur?

METHODS

A Medline search (2006-2011) was performed for clinical studies focusing on implant-supported SCs with a mean follow-up of at least 5 years. The search was complemented by an additional hand search and the inclusion of 24 studies from a previous systematic review (Jung et al. 2008a). Survival and complication rates were analyzed using random-effects Poisson's regression models to obtain summary estimates of 5- and 10-year proportions.

RESULTS

Forty-six studies derived from an initial search count of 1083 titles and the complementary publications from the previous systematic review (Jung et al. 2008a) were selected and the data were extracted. Based on the meta-analysis, survival of implants supporting SCs at 5 years amounted to 97.2% (95% CI: 96.3-97.9%), and at 10 years amounted to 95.2% (95% CI: 91.8-97.2%). The survival of implant-supported SCs was 96.3% (95% CI: 94.2-97.6%) after 5 years and 89.4% (95% CI: 82.8-93.6%) after 10 years. For biological complications, a 5-year cumulative soft tissue complication rate of 7.1% (95% CI: 4.4-11.3%) and a cumulative complication rate for implants with bone loss >2 mm of 5.2% (95% CI: 3.1-8.6%) were calculated. Technical complications reached a cumulative incidence of 8.8% (95% CI: 5.1-15.0%) for screw-loosening, 4.1% (95% CI: 2.2-7.5%) for loss of retention, and 3.5% (95% CI: 2.4-5.2%) for fracture of the veneering material after 5 years. The cumulative 5-year aesthetic complication rate amounted to 7.1% (95% CI: 3.6-13.6%).

CONCLUSIONS

The outcomes of the meta-analysis demonstrated high implant survival rates for both the single tooth implants and the respective single crowns after 5 and 10 years. However, technical, biological, and aesthetic complications were frequent.

Mechanical resistance of screwless morse taper and screw-retained implant-abutment connections

OBJECTIVE

The screwless morse taper (SMT) implant-abutment connection is an alternative to conventional external or internal screw-retained (ISR) connections. The aim of this in vitro study was to evaluate mechanical resistance of the SMT connection and to compare it with three different ISR connections.

MATERIALS AND METHODS

Four implant systems were tested in this study: SMT system; Tasarimmed Octo (Istanbul, Turkey), ISR systems; Straumann Bone Level (Basel, Switzerland), Biohorizons Internal (Birmingham, AL, USA), and Dentsply Friadent Xive (Mannheim, Germany). Overall, 64 specimens with stylized single crowns were prepared: 32 for dynamic loading (DL) and 32 for static loading (SL). DL was carried out using a chewing simulator with 120 N at 1.75 Hz for 1.2 × 10(6) cycles, and SL was performed with a universal testing machine at a crosshead speed of 2 mm/min with an angulation of 30°. Cycles until failure from DL and fracture/bending loads at SL were recorded. Statistical analyses were made with Dunn's multiple comparison.

RESULTS

Median cycles until failure in DL were as follows: Octo 86,354 (24,810-153,875), Straumann 1,200,000 (1,156,618-1,200,000), Biohorizons 539,719 (437,224-858,732), Xive 139,411 (139,411-139,411). Median fracture/bending loads in Newton at SL were as follows: Octo 429.6 (404.5-482.7), Straumann 574.6 (544.6-629.9), Biohorizons 548.7 (532.9-567.3), Xive 431.5 (412.5-520.5). There were significant differences between the implant systems under both loading conditions (P ≤ 0.05) revealing that the Octo implant system's SMT connection showed significantly lower cycles to failures and lower fracture/bending loads compared with the ISR connections of the Straumann and Biohorizons implant systems. However, there was no significant difference compared with the Xive implant system.

CONCLUSION

The mechanical resistance of the screwless morse taper implant system is lower than that of the ISR implant systems that might result in more frequent clinical complications.

Management of abutment screw loosening: review of literature and report of a case

Dental implant restoration has been widely accepted as one of the treatment modalities to replace missing teeth and to restore human masticatory function. The use of root form endosseous implant has increased considerably and this restorative option has become more refined with the introduction of newer designs and concepts. Long term post placement studies have reported prosthetic complications, including screw loosening, screw fracture, framework and implant fracture. Abutment screw loosening is the second most common cause of failure of implant supported restoration, next to loss of osseointegration. This is more seen in single implant supported restoration. Management of screw loosening is challenging and this clinical report describes the management of an implant abutment screw loosening of upper anterior teeth with minimal damage to the existing restoration making it possible to be reused and a literature review on the various factors associated with abutment screw loosening.

Dental implants installed in irradiated jaws: a systematic review

The aim of this study was to assess the survival rate of titanium implants placed in irradiated jaws. MEDLINE, EMBASE, and CENTRAL were searched for studies assessing implants that had been placed in nongrafted sites of irradiated patients. Random effects meta-analyses assessed implant loss in irradiated versus nonirradiated patients and in irradiated patients treated with hyperbaric oxygen (HBO) therapy. Of 1,051 potentially eligible publications, 15 were included. A total of 10,150 implants were assessed in the included studies, and of these, 1,689 (14.3%) had been placed in irradiated jaws. The mean survival rate in the studies ranged from 46.3% to 98.0%. The pooled estimates indicated a significant increase in the risk of implant failure in irradiated patients (risk ratio: 2.74; 95% confidence interval: 1.86, 4.05; p < .00001) and in maxillary sites (risk ratio: 5.96; 95% confidence interval: 2.71, 13.12; p < .00001). Conversely, HBO therapy did not reduce the risk of implant failure (risk ratio: 1.28; 95% confidence interval: 0.19, 8.82; p = .80). Radiotherapy was linked to higher implant failure in the maxilla, and HBO therapy did not improve implant survival. Most included publications reported data on machined implants, and only 3 studies on HBO therapy were included. Overall, implant therapy appears to be a viable treatment option for reestablishing adequate occlusion and masticatory conditions in irradiated patients.

Esthetic Evaluation of Single-Tooth Morse Taper Connection Implants Placed in Fresh Extraction Sockets or Healed Sites

The aim of this study was to compare the esthetic outcome of single implants placed in fresh extraction sockets with those placed in fully healed sites of the anterior maxilla. This retrospective study was based on data from patients treated with single-tooth Morse taper connection implants placed in fresh extraction sockets and in fully healed sites of the anterior maxilla. Only single implant treatments were considered with both neighboring teeth present. Additional prerequisites for immediate implant treatment were intact socket walls and a thick gingival biotype. The esthetic outcome was objectively rated using the pink esthetic/white esthetic score (PES/WES). The Mann-Whitney U test was used to compare the PES and the WES between the 2 groups. Twenty-two patients received an immediate implant, and 18 patients had conventional implant surgery. The mean follow-up was 31.09 months (SD 5.57; range 24–46) and 34.44 months (SD 7.10; range 24–48) for immediately and conventionally inserted implants, respectively. No implants were lost. All implants fulfilled the success criteria. The mean PES/WES was 14.50 (SD 2.52; range 9–19) and 15.61 (SD 3.20; range 8–20) for immediately and conventionally placed implants, respectively. Immediate implants had a mean PES of 7.45 (SD 1.62; range 4–10) and a mean WES of 7.04 (SD 1.29; range 5–10). Conventional implants had a mean PES of 7.83 (SD 1.58; range 4–10) and a mean WES of 7.77 (SD 1.66; range 4–10). The difference between the 2 groups was not significant. Immediate and conventional single implant treatment yielded comparable esthetic outcomes.

Immediate, non-submerged, root-analogue direct laser metal sintering (DLMS) implants: a 1-year prospective study on 15 patients

This study evaluated the 1-year survival and success rate of root-analogue direct laser metal sintering (DLMS) implants, placed into the extraction sockets of 15 patients. DLMS is a technology which allows solids with complex geometry to be fabricated by annealing metal powder microparticles in a focused laser beam, according to a computer-generated three-dimensional (3D) model; the fabrication process involves the laser-induced fusion of titanium microparticles, in order to build, layer-by-layer, the desired object. Cone-beam computed tomography (CBCT) acquisition and 3D image conversion, combined with the DLMS process, allow the fabrication of custom-made, root-analogue implants (RAIs). CBCT images of 15 non-restorable premolars (eight maxilla; seven mandible) were acquired and transformed into 3D models: from these, custom-made, root-analogue DLMS implants with integral abutment were fabricated. Immediately after tooth extraction, the RAIs were placed in the sockets and restored with a single crown. One year after implant placement, clinical and radiographic parameters were assessed: success criteria included absence of pain, suppuration, and exudation; absence of implant mobility and absence of continuous peri-implant radiolucency; distance between the implant shoulder and the first visible bone-to-implant contact <1.5 mm from initial surgery; and absence of prosthetic complications. At the 1-year follow-up, no implants were lost, for a survival rate of 100 %. All implants were stable, with no signs of infection. The good conditions of the peri-implant tissues were confirmed by the radiographic examination, with a mean DIB of 0.7 mm (±0.2). The possibility of fabricating custom-made, RAI DLMS implants opens new interesting horizons for immediate placement of dental implants.

Effect of loading time on the survival rate of anodic oxidized implants: prospective multicenter study

PURPOSE

The purpose of this prospective study was to evaluate the effect of early loading on survival rate or clinical parameter of anodic oxidized implants during the 12-month postloading period.

MATERIALS AND METHODS

Total 69 implants were placed in 42 patients. Anodic oxidized implants (GS II, Osstem Cor., Busan, Korea) placed on the posterior mandibles were divided into two groups, according to their prosthetic loading times: test group (2 to 6 weeks), and control group (3 to 4 months). The implant survival rates were determined during one-year postloading period and analyzed by Kaplan-Meier method. The radiographic peri-implant bone loss and periodontal parameters were also evaluated and statistically analyzed by unpaired t-test.

RESULTS

Total 69 implants were placed in 42 patients. The cumulative postloading implant survival rates were 88.89% in test group, compared to 100% in control group (P<.05). Periimplant marginal bone loss (T: 0.27±0.54 mm, C: 0.40±0.55 mm) and periodontal parameters showed no significant difference between the groups (P>.05).

CONCLUSION

Within the limitation of the present study, implant survival was affected by early loading on the anodic oxidized implants placed on posterior mandibles during one-year follow-up. Early implant loading did not influence peri-implant marginal bone loss, and periodontal parameters.

Influence of the interface design on the yield force of the implant-abutment complex before and after cyclic mechanical loading

PURPOSE

The aim of this in vitro study was to evaluate the implant-abutment assembly of Astra Tech (AST), Bego (BEG), Camlog (CAM), Friadent (FRI), Nobel Biocare (NOB) and Straumann (STR) with respect to yield force before and after cyclic fatigue, using a static overload test with a test set-up according to ISO 14801.

METHODS

Ten specimens of each type were split into two homogenous groups: one half was tested for static yield force without any further treatment (control), whereas the other one underwent one million cycles of mechanical loading with 100N as the upper load limit. For load-to-failure testing, specimens were then placed in a stainless steel jig and loaded in a universal testing machine under an angle of 30° with respect to the implant axis until failure. Load-displacement curves were analyzed and the yield forces at which non-linear behaviour set in (Fp) were recorded. Statistical analysis was performed using one-way ANOVA and t-test, respectively, with the level of significance set at 0.05.

RESULTS

Statistical analysis revealed that the type of implant-abutment connection has a significant influence on Fp (p<0.001). Furthermore, dynamic loading proved to significantly influence Fp of BEG and CAM (p<0.001).

CONCLUSION

None of the implant-abutment types tested would be expected to fail under clinically relevant forces, but the type of implant-abutment connection significantly influences the yield force Fp.