Evaluation and comparison of two selective extraction procedures for heavy metal speciation in sediments

Floating Treatment Wetland influences on the fate of metals in road runoff retention ponds

A field trial comparing the fate of metals in two parallel stormwater retention ponds, one of which was retrofitted with a Floating Treatment Wetland (FTW), was carried out near Auckland, New Zealand. Results suggest that the FTW increased metal accumulation in the pond sediment especially in summer due to lower sediment Eh, more anoxic water column, neutral pH and greater source of organic matter (OM) induced by the FTW. These factors combined with higher temperature enhanced metal sorption onto OM, flocculation of particulate pollutants, metal sulphide formation and reduced OM degradation and thus limited release of metals. Unlike Zn, Cu speciation in the pond sediment was relatively unchanged under various sediment Eh conditions due to its strong binding property with sulphide and OM. Occasional moderate metal release was detected from the FTW pond sediment likely due to aerobic OM degradation at the beginning of spring and/or hydroxides reduction when sediments became reduced later in the season. No release was noticed from the conventional pond sediment likely due to biosorption and/or uptake by algae which developed in the conventional pond and settled on the bottom sediment. Direct uptake by the plants of the FTW and sorption onto root plaques are not thought to be significant removal pathways. Nevertheless roots play a major role in trapping particulate pollutants, eventually sloughing off to settle on the bottom of the pond, and provide an adequate substrate for bacterial development due to release of organic compounds which are both essential for dissolved metal sorption and metal sulphide formation.

Geochemical fractionation of trace elements in sediments of Hugli River (Ganges) and Sundarban wetland (West Bengal, India)

A sequential extraction procedure was carried out to determinate the concentrations of 11 elements (Al, As, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Zn) in different geochemical phases of sediments collected along the Hugli (Ganges) River Estuary and in the Sundarban mangrove wetland, eastern coastal part of India. The chemical speciation of elements was determined using the three-step sequential extraction procedure described by the European Community Bureau of Reference. Total metal concentration was determined using a microwave-assisted acid digestion procedure. Metal concentrations were near the background level except for As for which a moderate pollution can be hypothesized. The mobility order of the metals was: Cd > Mn > Cu > Zn > As > Co > Pb > Ni > Fe > Cr > Al. The highest percentage of Cd (>60%) was found in the most labile phase. Residual fraction was prevailing for Fe, Cr and Al, while Pb was mainly associated with the reducible fraction. Data were compared with Sediment Quality Guidelines to estimate the relationship between element concentrations and adverse biological effects on benthic community, finding the possibility of some toxic effects due to the presence of As in the entire studied area and Cd, only in Calcutta.

Distribution and forms of manganese in vertisols of Serbia

Soil samples taken from the Ap horizont of arable land and meadows at ten different localities were analyzed for different forms of manganese, including total (HF), pseudo-total (HNO3), 0.1 M HClextractable and DTPA-extractable. A sequential fractional procedure was used for Mn portioning into fractions: water soluble and exchangeable Mn (I), specifically adsorbed Mn with carbonates (II), reductant releasable Mn in oxides (III), Mn bonded with organic matter (IV) and Mn structurally bonded in silicates (residual fraction) (V). Serbian vertisols have a normal Mn content, comparable with similar soils. The total (HF) and pseudo-total (HNO3) Mn contents were not correlated with soil properties, whereas the humus content positively influenced the 0.1 M HCl-extractable Mn in soil (r = 0.49

Distribution and partitioning of iron, zinc, and arsenic in surface sediments in the Grande River mouth to Cuitzeo Lake, Mexico

Cuitzeo Lake is one of the largest and most important lakes in Mexico. It receives different types of pollutants through its main tributary, the Grande River of Morelia. The aim of this work was to determine if high concentrations of iron, zinc, and arsenic are present in sediments in an area near the river mouth to the lake, as well as to estimate the partitioning of these metals using a sequential extraction procedure in order to obtain information of their potential bioavailability. Sediment samples were collected from three different sites in Cuitzeo Lake and two sites in Grande River in both dry and wet seasons. A sequential extraction procedure was carried out to determine the concentrations of these elements in different geochemical phases of the sediments. Total metal concentrations were evaluated by using the enrichment factor and the geoaccumulation index. A comparison with sediment quality guidelines and shale values has also been made. The results indicate that sediments are considered unpolluted by iron and moderately polluted by zinc and arsenic. However, fractionation studies showed that significant amounts of Zn and As could be released to the lake ecosystem depending on the environmental conditions, representing a medium risk potential of bioavailability to the biota.

Influence of contact duration on sediment-associated copper fractionation and bioavailability

Frequent utilization of copper formulations as aquatic herbicides and algaecides can lead to potentially elevated sediment-copper concentrations. This research investigated relationships between copper fractionation (through sequential extractions) and bioavailability in three reservoir sediments over a 60d contact duration. Copper was initially associated with exchangeable, carbonate, and oxidizable fractions for copper-amended sediments; and redistributed to the reducible and oxidizable fractions after 60d. Hyalella azteca mortality declined over time for organisms exposed to copper-amended reservoir sediments, indicating concomitant declines in sediment copper bioavailability. Comparisons between sequential extractions and organism responses indicated that bioavailability was primarily associated with the exchangeable fraction. Results of this research indicated fractionation and bioavailability of amended copper in sediments were influenced by contact duration along with sediment and overlying water characteristics. The influence of contact duration on copper bioavailability in sediments is important for assessing potential risks incurred by repeated applications of copper-containing algaecides in reservoirs.

Is there a future for sequential chemical extraction?

Since their introduction in the late 1970s, sequential extraction procedures have experienced a rapid increase in use. They are now applied for a large number of potentially toxic elements in a wide range of sample types. This review uses evidence from the literature to consider the usefulness and limitations of sequential extraction and thereby to assess its future role in environmental chemical analysis. It is not the intention to provide a comprehensive survey of all applications of sequential extractions or to consider the merits and disadvantages of individual schemes. These aspects have been covered adequately in other, recent reviews. This review focuses in particular on various key issues surrounding sequential extractions such as nomenclature, methodologies, presentation of data and interpretation of data, and discusses typical applications from the recent literature for which sequential extraction can provide useful and meaningful information. Also covered are emerging developments such as accelerated procedures using ultrasound- or microwave energy-assisted extractions, dynamic extractions, the use of chemometrics, the combination of sequential extraction with isotope analysis, and the extension of the approach to non-traditional analytes such as arsenic, mercury, selenium and radionuclides.

Monitoring metals in terrestrial environments within a bioavailability framework and a focus on soil extraction

Bioavailability considerations are one of the tools for a proper assignment of sites potentially and actually at risk as it allows assessing both the extent (hazard) and probability (risk) of adverse effects. In this paper, bioavailability considerations are linked to physico-chemical methods available for assessing metal fractions in soils. The focus of the overview is on empirical methods for extraction of metals from soils as a surrogate for the metal-, species- and soil-type-dependent bioavailable and bioaccessible metal pools. This cumulates in a generalized flow chart for monitoring of metals in soils. In support of the general monitoring strategy, examples are given of successful applications of analytical methods for predicting metal uptake by plants and animals, for assessing the origin of metals in soils, as well as the leaching potential of soils and the extent of soil contamination. It is concluded that a large arrays of chemical assessment methodologies for metal speciation in solid and liquid soil phases are available. As most assessment methodologies are operationally defined instead of being functionally defined, examples of mechanistically based monitoring approaches of bioavailability are still scarce. The value of the methods for measuring bioavailability can be significantly improved when the species, metal, and soil specific aspects of bioavailability are more accurately taken into account in the design of chemical simulation methodologies.

The Use of Sequential Extraction Procedures for the Characterization and Management of Contaminated Soils

Metal mobility and availability in solid samples, such as soils, sediments and sludges, is frequently studied with sequential extraction procedures, which allow to partition the total metal content into classes of different reactivity. From the experimental point of view, each extraction step requires many practical operations, which can represent sources of error if they are not properly executed. The first part of the paper gives indication on how to perform sequential extractions, from sample pretreatment to extract analysis, in order to reduce experimental errors. The second part describes the main applications of sequential extraction schemes for the characterization and management of contaminated soils: the assessment of the risks associated to metal pollution, the evaluation of the feasibility and efficiency of remediation techniques, the study of soil properties and of metal behaviour and plant availability.

Trace metals speciation in coastal particulate matter for marine environmental studies in Antarctica

Solid speciation of some trace metals (Pb, Cd, Fe, Mn, Cu) having environmental relevance was studied in coastal particulate sampled during the Austral Spring 2000/2001. A nearshore station situated in the Gerlache Inlet of Terra Nova Bay (Ross Sea, Antarctica) was sampled from November to February. Samples were collected using the in situ filtration system FIS500, equipped with polycarbonate membrane filters having different pore sizes (10 microm, 2 microm and 0.4 microm) for the size fraction analysis of particles. The total concentration of metals was determined both in dissolved and particulate fractions, while speciation was determined on particulate by applying a sequential extraction procedure. Concerning the surface and sub-surface layers, it has been observed that concentration of elements is mainly affected by the dynamic of the pack ice melting and by phytoplankton activity. The solid speciation in November and December is similar for all the studied elements, while some differences can be noted in February, when the pack has completely melted and phytoplankton bloom occurs. With the exception of iron, during this sampling period the quantity of metal associated to the labile fraction increases.

Metal speciation and environmental impact on sandy beaches due to El Salvador copper mine, Chile

Several coastal rocky shores in northern Chile have been affected by the discharges of copper mine tailings. The present study aims to analyze the chemical speciation of heavy metals in relation to the diversity of sessile species in the rocky intertidal benthic community on the northern Chilean coast, which is influenced by the presence of copper mine tailings. In particular, the chemical forms of Cd, Cu, Fe, Mn, Ni, Pb and Zn in beach sediment samples collected in the area influenced by El Salvador mine tailings were studied using a sequential chemical extraction method. In general, all the elements present a maximum concentration in the area near the actual discharge point (Caleta Palito). With regard to Cu and Mn, the concentrations range between 7.2-985 and 746-22,739 microg/g respectively, being lower than background levels only in the control site of Caleta Zenteno. Moreover, the correlation coefficients highlight that Fe, Mn and Ni correlate significantly and positively in the studied area, showing a possible common, natural origin, whilst Cu shows a negative correlation with Fe, Mn and Ni. It could be possible that Cu has an anthropogenic origin, coming from mining activity in the area. Cd, Fe, Mn, Ni, Pb and Zn are mostly associated with the residual phase, whilst Cu presents a different speciation pattern, as resulted from selective extractions. In fact, Cu is highly associated with organic and exchangeable phases in contaminated localities, whilst it is mainly bound to the residual phase in control sites. Moreover, our results, compared to local biological diversity, showed that those sites characterized by the highest metal concentrations in bioavailable phase had the lowest biodiversity.

Comparison of three sequential extraction procedures for partitioning of heavy metals in car park dusts

The aim of this study was to elucidate the amount of metal released at each step by using different extractants in three sequential extraction schemes for the partitioning of metal contents of car park deposited dust samples. For this purpose, three different sequential extraction procedures (SEP) were employed for the metal fractionation in car park dust samples collected from the campus of Erciyes University, Kayseri, Turkey. While two of the sequential extraction procedures contain five steps the other, namely the BCR sequential extraction scheme, has three steps. The first two methods fractionate metals to be exchangeable, bound to carbonates, bound to Mn oxides, bound to Fe oxides and bound to organic matter, and the BCR protocol fractionates the metals as acid soluble and exchangeable, reducible, and oxidisable. Determination of the metals Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn was performed by flame atomic absorption spectrometry (FAAS). The results obtained by the three methods were compared and showed that the amount of metal released at each step of the leaching procedure depended both on the type of reagents used and the sequence in which they were applied. The most mobile elements were Cd, Pb and Zn which are metals potentially toxic to the environment and are also known to originate from traffic. The calculated enrichment factors for Cd and Pb were substantially high (73.5-187 and 18.4-27.5, respectively) and somewhat lower for Zn (5.1-6.8). These results confirm that they are important metal pollutants for car parks. Detection limits and recoveries were found in the range of 0.01-1.39 microg ml(-1) and 68-126%, respectively, for the metals studied and the three sequential extraction procedures.

Protein-immobilized Electrode for Rapid and Convenient Sensing of Thyroid Hormone Receptor-ligand Interaction

The recombinant human thyroid hormone receptor (TR) was expressed as an in-frame fusion with ten consecutive histidine residues using a bacterial system; then the receptor was immobilized on an Au-electrode with Ni(II)-mediated chemisorption using the histidine tag and thiol-modified nitrilotriacetic acid. The receptor-modified electrode could rapidly detect ligand binding to hTR without any separation procedures, and showed a good response in a concentration-dependent manner. The sensitivity of this biosensor based on ligand-receptor interactions was comparable to those of conventional competitive ligand binding assays using radio-labeled ligands. Our results strongly suggest that our new biosensor can be applied to the identification of new ligands for hTR.

Piezo Electric Sensor for Endocrine-Disrupting Chemicals Using Receptor-co-factor Interaction

In vitro screening assays are useful techniques for the determination of receptor-mediated activities in environmental samples. In order to define whether environmental chemicals act as an agonist or antagonist to the human estrogen receptor (hER), we have constructed a biosensor based on ligand-inducible interactions between hER and relative proteins on a quartz crystal microbalance (QCM). The his-tagged proteins, which were expressed in E. coli by recombinant DNA technology, were immobilized on an Au-electrode with Ni(II)-mediated chemisorption using the histidine tag and thiol-modified iminodiacetic acid. The resonance-frequency change of the protein-modified electrode was caused by association or dissociation with the hER relative proteins on the surface in the presence of estrogen. These results suggest that this sensor is applicable as a large-scale screening tool for estrogenic compounds.