A Copper(II)-selective PVC Membrane Electrode Based on a Macrocyclic Ligand, 1,2,5,6,8,11-Hexaazacyclododeca-7,12-dione-2,4,8,10-tetraene

High selective potentiometric sensor for determination of nanomolar con-centration of Cu(II) using a polymeric electrode modified by a graphene/7,7,8,8-tetracyanoquinodimethane nanoparticles

In this paper we present several possibilities for modification of the all-solid-state copper(II)-selective electrodes in order to obtain high stability and selectivity potentiometric sensor signal. The copper(II)-selective electrodes were modified in a simple way by introducing solid contact layer based on graphene or graphene oxide, 7,7,8,8-tetracyanoquinodimethane or its copper salt. Each of electrodes shown a Nernstian response, wide linear range of Cu²⁺ concentration and a low detection limit. Nevertheless, some differences between the groups of electrodes have been noticed and resulted from application of intermediate layers of various compositions. The electrode modified with graphene and 7,7,8,8-tetracyanoquinodimethane nanocomposite exhibited the best potential reproducibility and detection limit. Moreover, prepared sensors were characterized by an improved selectivity for copper(II) in relation to non-modified electrodes. The developed electrodes were successfully used for the Cu²⁺ determination in different samples and results were comparable with those obtained using voltammetry.

Poly(vinyl) chloride membrane copper-selective electrode based on 1-phenyl-2-(2-hydroxyphenylhydrazo)butane-1,3-dione

1-Phenyl-2-(2-hydroxyphenylhydrazo)butane-1,3-dione (H(2)L) was used as an effective ionophore for copper-selective poly(vinyl) chloride (PVC) membrane electrodes. Optimization of the composition of the membrane and of the conditions of the analysis was performed, and under the optimized conditions the electrode has a detection limit of 6.30×10(-7) M Cu(II) at pH 4.0 with response time 10s and displays a linear EMF versus log[Cu(2+)] response over the concentration range 2.0×10(-6) to 5.0×10(-3) M Cu(II) with a Nernstian slope of 28.80±0.11 mV/decade over the pH range of 3.0-8.0. The sensor is stable for 9 weeks and exhibits good selectivity with respect to alkali, alkali earth and transition metal ions (e.g. Na(+), K(+), Ba(2+), Ca(2+), Zn(2+), Cd(2+), Co(2+), Mn(2+), Ni(2+), Fe(2+), Al(3+)) in the 3.0-8.0 pH range. It was successfully applied for the direct determination of copper(II) in zinc, aluminum and nickel based alloys, in soils polluted by oil, and as an indicator electrode for potentiometric titration of copper ions with EDTA.

Developments in the Field of Conducting and Non-conducting Polymer Based Potentiometric Membrane Sensors for Ions Over the Past Decade

Many research studies have been conducted on the use of conjugated polymers in the construction of chemical sensors including potentiometric, conductometric and amperometric sensors or biosensors over the last decade. The induction of conductivity on conjugated polymers by treating them with suitable oxidizing agents won Heeger, MacDiarmid and Shirakawa the 2000 Nobel Prize in Chemistry. Common conjugated polymers are poly(acetylene)s, poly(pyrrole)s, poly(thiophene)s, poly(terthiophene)s, poly(aniline)s, poly(fluorine)s, poly(3-alkylthiophene)s, polytetrathiafulvalenes, polynapthalenes, poly(p-phenylene sulfide), poly(p-phenylenevinylene)s, poly(3,4-ethylenedioxythiophene), polyparaphenylene, polyazulene, polyparaphenylene sulfide, polycarbazole and polydiaminonaphthalene. More than 60 sensors for inorganic cations and anions with different characteristics based on conducting polymers have been reported. There have also been reports on the application of non-conducting polymers (nCPs), i.e. PVC, in the construction of potentiometric membrane sensors for determination of more than 60 inorganic cations and anions. However, the leakage of ionophores from the membranes based on these polymers leads to relatively lower life times. In this article, we try to give an overview of Solid-Contact ISE (SCISE), Single-Piece ISE (SPISE), Conducting Polymer (CP)-Based, and also non-conducting polymer PVC-based ISEs for various ions which their difference is in the way of the polymer used with selective membrane. In SCISEs and SPISEs, the plasticized PVC containing the ionophore and ionic additives govern the selectivity behavior of the electrode and the conducting polymer is responsible of ion-to-electron transducer. However, in CPISEs, the conducting polymer layer is doped with a suitable ionophore which enhances the ion selectivity of the CP while its redox response has to be suppressed.