Is cell culture stressful? Effects of degradable and nondegradable culture surfaces on U937 cell function

Rapid Manufacturing of Multilayered Microfluidic Devices for Organ on a Chip Applications

Microfabrication and Polydimethylsiloxane (PDMS) soft-lithography techniques became popular for microfluidic prototyping at the lab, but even after protocol optimization, fabrication is yet a long, laborious process and partly user-dependent. Furthermore, the time and money required for the master fabrication process, necessary at any design upgrade, is still elevated. Digital Manufacturing (DM) and Rapid-Prototyping (RP) for microfluidics applications arise as a solution to this and other limitations of photo and soft-lithography fabrication techniques. Particularly for this paper, we will focus on the use of subtractive DM techniques for Organ-on-a-Chip (OoC) applications. Main available thermoplastics for microfluidics are suggested as material choices for device fabrication. The aim of this review is to explore DM and RP technologies for fabrication of an OoC with an embedded membrane after the evaluation of the main limitations of PDMS soft-lithography strategy. Different material options are also reviewed, as well as various bonding strategies. Finally, a new functional OoC device is showed, defining protocols for its fabrication in Cyclic Olefin Polymer (COP) using two different RP technologies. Different cells are seeded in both sides of the membrane as a proof of concept to test the optical and fluidic properties of the device.

Characterization of a degradable polar hydrophobic ionic polyurethane with circulating angiogenic cells in vitro

This study investigated the interaction of human circulating angiogenic cells (CACs) with a degradable polar hydrophobic ionic polyurethane (D-PHI) which has been previously shown to exhibit anti-inflammatory character and favorable interactions with human endothelial cells (ECs). Given the implication of the CACs in microvessel development it was of intrinsic interest to expand our knowledge of D-PHI biocompatibility with this relevant primary cell involved in angiogenesis. The findings will be compared to a well-established benchmark substrate for CACs, fibronectin-coated tissue culture polystyrene (TCPS). Immunoblotting analysis showed that CACs were a heterogeneous population of cells composed mostly of monocytic cells expressing the CD14 marker. Assessment of the cytokine release profile, using ELISA, showed that D-PHI supported a higher concentration of interleukin-10 (IL-10) when compared to the concentration of tumor necrosis factor alpha, which is indicative of an anti-inflammatory phenotype, and was different from the response with TCPS. It was found that the CACs were attached to D-PHI and remained viable and functional (nitric oxide production) during the seven days of culture. However, there did not appear to be any significant proliferation on D-PHI, contrary to the CAC growth on fibronectin-coated TCPS. It was concluded that D-PHI displayed some of the qualities suitable to enable the retention of CACs onto this substrate, as well as maintaining an anti-inflammatory phenotype, characteristics which have been reported to be important for angiogenesis in vivo.

Differences in protein binding and cytokine release from monocytes on commercially sourced tissue culture polystyrene

Tissue culture polystyrene (TCPS) is a ubiquitous substrate used by many researchers in the biomedical and biological sciences. Different parameters involved in the production of TCPS, including the treatment time and the use of reactive gases and chemical agents, can have a significant influence on the ultimate surface properties achieved. The assumption that they will all yield a consistent and controlled product has not proven to be true. To provide a better insight into the bioactivity differences in TCPS supplied by different manufacturers, TCPS from three different companies (Sarstedt, Wisent Corp., and Becton Dickinson (BD)) were analyzed for their surface properties, protein adsorption characteristics, and interactions with human monocytes. Marked differences were observed in terms of surface wettability and surface chemistry. Furthermore, Wisent TCPS adsorbed more than twice the amount of serum proteins compared with BD and Sarstedt TCPS. Sarstedt showed significantly more cell retention (more DNA) compared with both BD and Wisent TCPS brands over a 7 day culture period. Cytokine release from monocytes adherent on the three different TCPS also differed significantly, suggesting that the differences in the surface properties were sufficient to differentially mediate monocyte activation. These results have important implications for TCPS research use, in terms of appreciating the interpretation of the data when TCPS is used as a control substrate as well as when it is used where a pre-conditioned state would influence the outcome of the study.

Fetal bovine serum xenoproteins modulate human monocyte adhesion and protein release on biomaterials in vitro

Monocyte-derived macrophages are critical in the host-foreign body response to biomaterials and have been studied extensively in various culture conditions in vitro, such as medium supplemented with fetal bovine serum (FBS) or autologous human serum (AHS). Since monocyte maturation into macrophages is highly plastic and may vary considerably depending on the surface, isolation procedures and in vitro culture conditions, we hypothesize that variations in protein adsorption and serum type will greatly impact monocyte behavior in a surface-dependent manner. The impact of xenoproteins on monocyte-surface interactions has not been well studied methodically and the use of AHS rather than FBS for macrophage-biomaterials studies in vitro is far from universal. The commonly used reference materials - tissue culture polystyrene (TCPS), polyethylene glycol (PEG) and polydimethylsiloxane (PDMS) - were employed in this study and we found a 3-fold higher adherent monocyte density on TCPS when AHS was used vs. FBS-supplemented medium. On PEG hydrogels, an 8- to 10-fold higher adhesion density was observed when AHS was employed vs. FBS, while on PDMS no difference in adhesion density was observed between the two sera conditions. Additionally, the presence of lipopolysaccharide abrogated the serum-dependent effect on cell adhesion on TCPS. Significantly different variations in protein release were observed between the serum conditions on these surfaces; in particular, there was a 100-fold higher concentration of growth-related oncogene for the AHS condition on PDMS even though the adhesion levels were comparable between the two serum conditions. These results emphasize the combined impact of the surface type and FBS xenoproteins in mediating the observed monocyte response to biomaterials in vitro.

Differentiation of monocytes on a degradable, polar, hydrophobic, ionic polyurethane: Two-dimensional films vs. three-dimensional scaffolds

A degradable, polar, hydrophobic, ionic polyurethane (D-PHI), with physical properties comparable to those of peripheral arterial vascular tissue, was evaluated for monocyte interactions with two different physical forms: two-dimensional films and three-dimensional porous scaffolds. Monocytes, isolated from human whole blood, were seeded onto D-PHI films and scaffolds, and differentiated to monocyte-derived macrophages (MDM) for up to 28 days. The effect of surface structure on the MDM phenotype was assessed by assaying: cell attachment (DNA), activation (intracellular protein expression, esterase and acid phosphatase (AP) activity) as well as pro- and anti-inflammatory cytokines (TNF-α and IL-10, respectively). The cells on scaffolds exhibited an initial peak in total protein synthesized per DNA at 3 days; however, both substrates generated similar protein levels per DNA at all other time points. While scaffolds generated more esterase and AP per cell than for films, the cells on films expressed significantly more of these two proteins relative to their total protein produced. At day 7 (acute phase of monocyte activation), cells on films were significantly more activated than monocytes on the scaffolds as assessed by cell morphology and tumor necrosis factor-α and interleukin-10 levels. Histological analysis of scaffolds showed that cells were able to migrate throughout the three-dimensional matrix. By inducing a low inflammatory, high wound-healing phenotype monocyte, the negative effects of the foreign body reaction in vivo may be controlled in a manner possible to direct the vascular tissue cells into the appropriate functional phenotypes necessary for successful tissue engineering.

Tailoring the degradation kinetics of poly(ester carbonate urethane)urea thermoplastic elastomers for tissue engineering scaffolds

Biodegradable elastomeric scaffolds are of increasing interest for applications in soft tissue repair and regeneration, particularly in mechanically active settings. The rate at which such a scaffold should degrade for optimal outcomes, however, is not generally known and the ability to select from similar scaffolds that vary in degradation behavior to allow such optimization is limited. Our objective was to synthesize a family of biodegradable polyurethane elastomers where partial substitution of polyester segments with polycarbonate segments in the polymer backbone would lead to slower degradation behavior. Specifically, we synthesized poly(ester carbonate)urethane ureas (PECUUs) using a blended soft segment of poly(caprolactone) (PCL) and poly(1,6-hexamethylene carbonate) (PHC), a 1,4-diisocyanatobutane hard segment and chain extension with putrescine. Soft segment PCL/PHC molar ratios of 100/0, 75/25, 50/50, 25/75, and 0/100 were investigated. Polymer tensile strengths varied from 14 to 34 MPa with breaking strains of 660-875%, initial moduli of 8-24 MPa and 100% recovery after 10% strain. Increased PHC content was associated with softer, more distensible films. Scaffolds produced by salt leaching supported smooth muscle cell adhesion and growth in vitro. PECUU in aqueous buffer in vitro and subcutaneous implants in rats of PECUU scaffolds showed degradation slower than comparable poly(ester urethane)urea and faster than poly(carbonate urethane)urea. These slower degrading thermoplastic polyurethanes provide opportunities to investigate the role of relative degradation rates for mechanically supportive scaffolds in a variety of soft tissue repair and reconstructive procedures.

Assays on the influence of biomaterials on allogeneic rejection in tissue engineering

In tissue engineering, innate responses to biomaterial scaffolds will affect rejection of allogeneic cells. Biomaterials directly influence innate and adaptive immune cell adhesion, reactive oxygen intermediate production, cytokine secretion, nuclear factor-kappa B nuclear translocation, gene expression, and cell surface markers, all of which are likely to affect allogeneic rejection responses. A major goal in tissue engineering is to induce transplant tolerance, potentially by manipulating the biomaterial component. This review describes methods of measuring responses of macrophages, dendritic cells, and T cells stimulated in vitro and in vivo and addresses key factors in assay development. Such tests include mixed leukocyte reactions, enzyme-linked immunosorbent spot assays, trans-vivo delayed-type hypersensitivity assays, and measurement of dendritic cell subsets and anti-donor antibodies; we propose extending these studies to tissue engineering.

Effect of phorbol esters on the macrophage-mediated biodegradation of polyurethanes via protein kinase C activation and other pathways

It was previously found that re-seeding monocyte-derived macrophages (MDM) on polycarbonate-based polyurethanes (PCNUs) in the presence of the protein kinase C (PKC) activator phorbol myristate acetate (PMA) inhibited MDM-mediated degradation of PCNUs synthesized with 1,6-hexane diisocyanate (HDI), as well as esterase activity and monocyte-specific esterase (MSE) protein. However, no effect on the degradation of a 4,4'-methylene bisphenyl (MDI)-derived PCNU (MDI321) occurred. This finding suggested that oxidation, a process linked to the PKC pathway, was not activated in the same manner for all PCNUs. In the current study MDM were re-seeded onto the above PCNU surfaces with PMA, PKC-inactive 4alphaPMA and the PKC inhibitor bisindolylmaleimide I hydrochloride (BIM) for 48 h before assaying for PCNU degradation, esterase activity, MSE protein, DNA, cell viability and cell morphology. 4alphaPMA did not alter MDM-mediated HDI PCNU degradation but MDI321 degradation increased in this condition. BIM alone had no effect on any parameter; however, when BIM and PMA were added together, the PMA inhibition of biodegradation, esterase activity and MSE protein was partially reversed for MDM on HDI PCNUs only. Adding PMA to MDM on HDI PCNUs increased intercellular connections, whereas 4alphaPMA or BIM+PMA increased cell size. Although this study demonstrated a role for oxidation via a PKC-activated pathway in MDM-mediated PCNU degradation, phorbol esters appear to also activate non-PKC pathways that have roles in biodegradation. Moreover, the sensitivity to material surface chemistry in the MDM response to each PCNU dictates a multi-factorial degradative process involving alternate material specific oxidative and hydrolytic mechanisms.

Influence of biodegradable and non-biodegradable material surfaces on the differentiation of human monocyte-derived macrophages

Monocyte-derived macrophages (MDM) and multinucleated foreign body giant cells (FBGC) are the primary cell types that remain at the cell-material interface of polyurethane (PU)-based medical devices as a result of chronic inflammatory responses. In vitro studies have demonstrated that MDM possess degradative potential toward PU, which can result in device failure. Because most studies have followed the degradation potential, morphology, and function of these cells only once fully differentiated, the current study investigated the influence of a non-degradable control tissue culture-grade polystyrene (TCPS) surface relative to two degradable model polycarbonate-urethanes (PCNU), of different chemistry, on various parameters of MDM morphology and function during a 14-day differentiation time course. The differentiation of human monocytes isolated from whole blood on PCNU materials resulted in increased cell attachment, decreased multinucleation, and significant decreases in cell spreading when compared with cells differentiated on TCPS. Actin-stained podosome-like cell adhesion structures were increased in PCNU-adherent cells, accompanied by an alteration in beta-actin and vinculin protein expression. The expression of the CD68 macrophage marker was reduced when cells were adherent to the PCNU materials and compared with TCPS, suggesting altered cell activation by the degradable relative to non-degradable materials. The degradative potential of these cells was altered by the material surface they were exposed to as measured by esterase activity and protein expression of monocyte-specific esterase. This was also supported by physical material breakdown evident in scanning electron microscopy images that illustrated holes in the PCNU films generated by the presence of differentiating MDM. It was concluded from these studies that PCNU materials significantly alter the function and morphology of differentiating MDM. This must be taken into consideration when studying cell-material interactions because these cells will receive cues from their immediate environment (including the biomaterial) upon differentiation, thereby affecting their resulting phenotype.