Acrylic acid removal by acrylic acid utilizing bacteria from acrylonitrile-butadiene-styrene resin manufactured wastewater treatment system

Degradation of high-strength acrylic acid wastewater with anaerobic granulation technology: A mini-review

The anaerobic granulation technology has been successfully applied full-scale for treating high-strength recalcitrant acrylic acid wastewater. This mini-review highlighted the recalcitrance of acrylic acid and its biological degradation pathways. And then, the full-scale practices using anaerobic granulation technology for acrylic wastewater treatment were outlined. The granules are proposed to provide barriers for high-concentration acrylic acid to the embedded anaerobic microbes, maintaining its high degradation rate without apparent substrate inhibition. Based on this proposal, the prospects of applying anaerobic granulation technology to handle a wide range of high-strength recalcitrant wastewaters, to improve the current process performances, and to recover renewable resources were delineated. The anaerobic granulation for high-strength recalcitrant wastewater treatment is an emergent technology that can assist in fulfilling the appeals of the circular bioeconomy of modern society.

A three-dimensional (3D) printing approach to fabricate an isolation chip for high throughput in situ cultivation of environmental microbes

The full plethora of environmental bacteria is often poorly represented in vitro as the majority remain difficult, if not impossible, to culture under standard laboratory settings. These bacteria often require native conditions for the formation of cell masses that collectively have higher chances of survival. With that, a 3D-printed version of the isolation chip (iChip) was used to cultivate bacteria from a tropical peat swamp in situ prior to growth and maintenance in vitro. Briefly, plates made from either acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), or epoxy resin were tested in terms of their usability and durability under acidic conditions similar to those of peat matter. The epoxy resin plates were then found to be most optimal for the sampling conditions. Peat soil samples were collected from the base of a Koompassia malaccensis tree and reconstituted in molten 10% (wt/vol) tryptone soy agar (TSA) prior to inoculation. The iChips were subsequently assembled and buried in the site of origin. As a comparison, bacteria from the same soil sample were cultivated directly on TSA and incubated at 28 °C for two weeks. Thereafter, agar plugs from the iChip were transferred to TSA plates to allow microcolonies within each plug to grow. Each pure isolate from both cultivation approaches that grew was then pooled and extracted for total DNA prior to 16S rRNA gene amplification and sequencing via Illumina MiSeq. Taxonomic abundance comparison revealed that the bacterial taxa at the level of order were significantly different between the two approaches, particularly in the orders, Burkholderiales, Xanthomonodales, Enterobacteriales, and Actinomycetales (differences of 12.0, 7.1, 8.0, and 4.2%, respectively). This indicated that the 3D-printed iChips present a possible low-cost tool for the isolation of bacterial genera that may not be able to grow on media directly in vitro.

Supercritical water oxidation of acrylic acid production wastewater

Supercritical water oxidation (SCWO) of wastewater from an acrylic acid manufacturing plant has been studied on a continuous flow experimental system, whose reactor was made of Hastelloy C-276. Experimental conditions included a reaction temperature (T) ranging from 673 to 773K, a residence time (t) ranging from 72.7 to 339s, a constant pressure (P) of 25 MPa and a fixed oxidation coefficient (alpha) of 2.0. Experimental results indicated that reaction temperature and residence time had significant influences on the oxidation reaction, and increasing the two operation parameters could improve both degradation of chemical oxygen demand (COD) and ammonia nitrogen (NH3-N). The COD removal efficiency could reach up to 98.73% at 25 MPa, 773 K and 180.1 s, whereas the destruction efficiency of NH3-N was only 43.71%. We further carried out a kinetic analysis considering the induction period through free radical chain mechanism. It confirms that the power-law rate equation for COD removal was 345 exp(-52200/RT)[COD]1.98[O2]0.17 and for NH3-N removal was 500 exp(-64492.19/RT)[NH3-N]1.87 [O2]0.03. Moreover, the induction time formulations for COD and NH3-N were suspected to be exp(38250/RT)/173 and exp(55690/RT)/15231, respectively. Correspondingly, induction time changed from 2.22 to 5.38 s for COD and 0.38 to 1.38 s for NH3-N. Owing to the catalysis of reactor inner wall surface, more than 97% COD removal was achieved in all samples.

Inhibitory effect of cyanide on nitrification process and its eliminating method in a suspended activated sludge process

Inhibition of nitrification by four typical pollutants (acrylonitrile, acrylic acid, acetonitrile and cyanide) in acrylonitrile wastewater was investigated. The inhibitory effect of cyanide on nitrification was strongest, with a 50% inhibitory concentration of 0.218 mg·gVSS-1 being observed in a municipal activated sludge system. However, the performance of nitrification was recovered when cyanide was completely degraded. The nitrification, which had been inhibited by 4.17 mg·gVSS-1 of free cyanide for 24 h, was recovered to greater than 95% of that without cyanide after 10 days of recovery. To overcome cyanide inhibition, cyanide-degrading bacteria were cultivated in a batch reactor by increasing the influent cyanide concentration in a stepwise manner, which resulted in an increase in the average cyanide degradation rate from 0.14 to 1.01 mg CN-·gVSS-1·h-1 over 20 days. The cultured cyanide-degrading bacteria were shaped like short rods, and the dominant cyanide-degrading bacteria strain was identified as Pseudomonas fluorescens NCIMB by PCR.

Coral-associated bacteria and their role in the biogeochemical cycling of sulfur

Marine bacteria play a central role in the degradation of dimethylsulfoniopropionate (DMSP) to dimethyl sulfide (DMS) and acrylic acid, DMS being critical to cloud formation and thereby cooling effects on the climate. High concentrations of DMSP and DMS have been reported in scleractinian coral tissues although, to date, there have been no investigations into the influence of these organic sulfur compounds on coral-associated bacteria. Two coral species, Montipora aequituberculata and Acropora millepora, were sampled and their bacterial communities were characterized by both culture-dependent and molecular techniques. Four genera, Roseobacter, Spongiobacter, Vibrio, and Alteromonas, which were isolated on media with either DMSP or DMS as the sole carbon source, comprised the majority of clones retrieved from coral mucus and tissue 16S rRNA gene clone libraries. Clones affiliated with Roseobacter sp. constituted 28% of the M. aequituberculata tissue libraries, while 59% of the clones from the A. millepora libraries were affiliated with sequences related to the Spongiobacter genus. Vibrio spp. were commonly isolated from DMS and acrylic acid enrichments and were also present in 16S rRNA gene libraries from coral mucus, suggesting that under "normal" environmental conditions, they are a natural component of coral-associated communities. Genes homologous to dddD, and dddL, previously implicated in DMSP degradation, were also characterized from isolated strains, confirming that bacteria associated with corals have the potential to metabolize this sulfur compound when present in coral tissues. Our results demonstrate that DMSP, DMS, and acrylic acid potentially act as nutrient sources for coral-associated bacteria and that these sulfur compounds are likely to play a role in structuring bacterial communities in corals, with important consequences for the health of both corals and coral reef ecosystems.