Application of response surface methodology to optimize the fabrication of ZnCl2-activated carbon from sugarcane bagasse for the removal of Cu2

Super facile one-step synthesis of sugarcane bagasse derived N-doped porous biochar for adsorption of ciprofloxacin

A new N-doped biochar derived from sugarcane bagasse (NSB) was prepared by one-pot pyrolysis with sugarcane bagasse as feedstock, melamine as nitrogen source and NaHCO₃ as pore-forming agent, and then NSB was used to adsorb ciprofloxacin (CIP) in water. The optimal preparation conditions of NSB were determined based on the evaluation index of adsorbability of NSB for CIP. SEM, EDS, XRD, FTIR, XPS and BET characterizations were used to analyze the physicochemical properties of the synthetic NSB. It was found that the prepared NSB had excellent pore structure, high specific surface area and more nitrogenous functional groups. Meanwhile, it was demonstrated that the synergistic interaction between melamine and NaHCO₃ increased the pores of NSB and the largest surface area of NSB was 1712.19 m²/g. The CIP adsorption capacity of 212 mg/g was obtained under optimal parameters as follows: NSB amount 0.125 g/L, initial pH 6.58, adsorption temperature 30 °C, CIP initial concentration 30 mg/L and adsorption time 1 h. The isotherm and kinetics studies elucidated that the adsorption of CIP conformed both D-R model and Pseudo-second-order kinetic model. The high CIP adsorption capacity of NSB for CIP was due to the combined filling pore, π-π conjugation and hydrogen bonding. All results demonstrated that adsorption of CIP by the low-cost N-doped biochar of NSB is a reliable technology for the disposal of CIP wastewater.

A Critical Review of the Removal of Radionuclides from Wastewater Employing Activated Carbon as an Adsorbent

Radionuclide-contaminated water is carcinogenic and poses numerous severe health risks and environmental dangers. The activated carbon (AC)-based adsorption technique has great potential for treating radionuclide-contaminated water due to its simple design, high efficiency, wide pH range, quickness, low cost and environmental friendliness. This critical review first provides a brief overview of the concerned radionuclides with their associated health hazards as well as different removal techniques and their efficacy of removing them. Following this overview, this study summarizes the surface characteristics and adsorption capabilities of AC derived from different biomass precursors. It compares the adsorption performance of AC to other adsorbents, such as zeolite, graphene, carbon nano-tubes and metal-organic frameworks. Furthermore, this study highlights the different factors that influence the physical characteristics of AC and adsorption capacity, including contact time, solution pH, initial concentration of radionuclides, the initial dosage of the adsorbent, and adsorption temperature. The theoretical models of adsorption isotherm and kinetics, along with their fitting parameter values for AC/radionuclide pairs, are also reviewed. Finally, the modification procedures of pristine AC, factors determining AC characteristics and the impact of modifying agents on the adsorption ability of AC are elucidated in this study; therefore, further research and development can be promoted for designing a highly efficient and practical adsorption-based radionuclide removal system.

Application of the Response Surface Methodology (RSM) in the Optimization of Acenaphthene (ACN) Removal from Wastewater by Activated Carbon

The presence of polycyclic aromatic hydrocarbons (PAHs) in wastewater has raised concerns about human health due to their potential carcinogenic and mutagenic properties. The widespread use of products containing acenaphthene (ACN, one of the 16 priority PAHs) in many industries and large-scale ACN release into the wastewater has resulted in dangerous concentrations of ACN in the environment. As a result, before discharge, it is required to eliminate or reduce its concentration to an acceptable level. Adsorption is an effective method of removing PAHs from wastewater. In this study, the ACN adsorption reaction in sample wastewater was evaluated using activated carbon produced by oil palm leaves. HPLC was used as an analytical method for quantifying ACN in wastewater samples. The initial concentration of ACN in water samples was 9.58 ± 0.5 mg/L. The experiments were conducted using the CCD combined with the RSM and using three independent variables, i.e., pH, activated carbon dosage (g/L), and contact time (min), and one dependent variable, i.e., ACN removal efficiency (%). The ANOVA was used to identify the significance of the developed model in the RSM. Lastly, the RSM was used to optimize the adsorption results. The experimental results determined that the removal of 98.73 ± 1% of ACN (the highest amount) was achieved at pH 7, while the removal of 88.44 ± 1% of ACN (the lowest amount) was achieved at pH 4.5. The adsorption efficiency of ACN was slightly increased by an increase in activated carbon dosage from 0.1 to 3 g/L (<4%). The contact time was the most significant factor in controlling the adsorption efficiency of ACN in wastewater, and not pH value or dosage. The adsorption reaction was quick, and 88–90% of ACN was removed within 5 min of the adsorption reaction, followed by slower adsorption for up to 90 min. The RSM model was developed on the basis of experimental results. An ANOVA determined that the developed model was significant enough to represent the adsorption data as the p-value was <0.05 for the model. The factors pH, adsorbent dosage, and contact time were also significant factors (p-value < 0.05). The optimization results showed that pH of 6.96, adsorbent dosage of 2.62 g/L, and contact time of 71.67 min were the optimal conditions for eliminating 98.88% of the ACN. The optimization results were verified in the lab, and a close agreement was found between the predicted results of the RSM and experimental results. The study found that the RSM is an effective tool for optimizing operating variables, as well as for significantly reducing time and experimentation costs.

An insight on Vietnamese bio-waste materials as activated carbon precursors for multiple applications in environmental protection

Vietnam is known as an agricultural country with a variety of agricultural crops. In addition to agricultural by-products, bio-waste is the by-product from livestock waste, forestry, industry, and daily life. They affect the soil, water, and air environment by self-degradation processes in the environment. Therefore, researchers have come up with ideas for the usage of the by-products to decrease the amount of waste and minimize the environmental effects. In Vietnam, the by-products were used by researchers to produce bio-ethanol, fertilizers, composites, and activated carbon (AC). AC is one of the materials used to rapidly reduce the number of agricultural by-products by researchers. The synthesis process is optimized for the highest yield, while the physicochemical properties are also clearly analyzed through the X-ray diffraction, Fourier transform infrared, and Bacterial endotoxin testing assays. The average recorded specific surface area was about 300 m2 g−1. The functional groups and surface structure showed that the material has an amorphous structure with –OH, –CH, –CC, –C═C, –C═O groups. The AC from agricultural waste had been studied and applied to treat pollutants present in water.

Sacrificial Zinc Oxide Strategy-Enhanced Mesoporosity in MIL-53-Derived Iron–Carbon Composite for Methylene Blue Adsorption

MOF-derived carbon-based materials have attracted widespread attention due to their relatively large surface area, morphology, and their stability in water. Considering these advantages, these materials present themselves as excellent adsorbents. In this work, a novel method was designed for the fabrication of a nano zero-valent-iron (nZVI) carbon composite. The utilization of zinc oxide nanorods (ZnONRs) in the role of sacrificial consumable nuclei for the synthesis of MIL-53 sacrificial zinc oxide nanorods (MIL-53-SNR) and the subsequent pyrolysis at 700 °C in the inert atmosphere led to a graphitic-supported nZVI material (Fe-C-SNR). Fe-C-SNR was compared with a commercial zinc oxide bulk (MIL-53-SB) and with a pristine MIL-53. By virtue of the ZnONRs, Fe-C-SNR exhibited a greatly improved mesoporous structure. Consequently, the pyrolyzed materials were applied as adsorbents for methylene blue. Fe-C-SNR’s performance increased to more than double of the pyrolyzed MIL-53 (Fe-C), with a remarkably fast adsorption time (10 min) for a concentration of 10 mg L−1 with only 200 mg L−1 adsorbent required. This functional composite also displayed exceptional recyclability; after ten complete cycles, Fe-C-SNR was still capable of completely adsorbing the methylene blue. The utilization of ZnONRs proves itself advantageous and could further be extended to other MOFs for a wide range of applications.

Modified Activated Carbon Synthesized from Oil Palm Leaves Waste as a Novel Green Adsorbent for Chemical Oxygen Demand in Produced Water

Palm tree waste is one of the most widespread forms of agricultural waste, particularly in areas where oil palms are cultivated, and its management is one of the industry’s key concerns. To deal with this palm waste, researchers are working hard to work out the ways to convert this plentiful waste into useful material for future beneficial applications. The objective of this study was to employ chemical activation techniques to prepare a new activated carbon (AC) using discarded oil palm leaves (OPL) in Malaysia. Three chemical agents (H3PO4, NaOH and ZnCl2), as well as three pyrolysis temperatures (400 °C, 600 °C and 800 °C) and various impregnation ratios (1:0.5–1:3) were used to optimize the preparation process. As a result, the oil palm leaves activated carbon (OPLAC), with prominent surface properties, was obtained by ZnCl2 activations with a 1:1 impregnation ratio and carbonized at a pyrolysis temperature of 800 °C. The OPLAC-ZC had a surface area of 331.153 m2/g, pore size of 2.494 nm and carbon content of 81.2%. Results showed that the OPLAC-ZC was able to quickly (90 min) remove the chemical oxygen demand (COD) from produced water (PW), through chemical adsorption and an intraparticle diffusion mechanism. The material followed pseudo-second order kinetic and Freundlich isotherm models. The maximum adsorption capacity of organic pollutants forming COD in PW was found to be 4.62 mg/g (59.6 ± 5%). When compared to previous studies, the OPLAC-ZC showed equivalent or better COD removal capability. It is the first detailed study reporting the preparation of AC from OPL and applying it for organic pollutants adsorption forming COD in PW.

Evolution of physico-chemical properties of Dicranopteris linearis-derived activated carbon under various physical activation atmospheres

This work emphasizes the effect of the physical activation using CO2 and steam agents on the physicochemical properties of activated carbon produced from Dicranopteris linearis (D. linearis), a fern species widely distributed across tropic and subtropic ecoregions. The D. linearis-derived chars produced under pyrolysis at 400 °C for 1 h were activated in various CO2-steam proportions. As revealed by the IR and Raman spectra, the structure of the activated chars was heavily dependent on the relative proportion of CO2 and steam. The total specific surface area (SSA) of the activated chars proportionally increased with the increase in steam proportion and was comparable to the values of commercial activated char products. Specifically, the activation under CO2- and steam-saturated conditions has correspondingly resulted in SSA increasing from 89 to 653 m2g-1 and from 89 to 1015 m2g-1. Steam also enhanced the development of mesoporous structures of the D. linearis-derived char products, thereby extending their potential applications, particularly for industries that require high rigidity in the product such as pharmaceutical and cosmetic sectors.

Effects of Various Processing Parameters on Polyphenols, Flavonoids, and Antioxidant Activities of Codonopsis javanica Root Extract

The root of a ginseng-like plant named Codonopsis javanica is a valuable ingredient in folk medicine with diverse biological properties and has been used in treatments for various diseases, including leukemia, inflammation, and hepatitis. This study aimed to optimize various parameters related to the extraction process of C. javanica root (CJR) with respect to total phenolic content (TPC), total flavonoid content, and antioxidant activities of the obtained CJR extract. We first performed a series of single-factor investigations taking drying conditions and different extraction parameters such as material size, extraction solvent, solvent concentration, extraction temperature, material/solvent ratio, extraction cycle, and stirring speed as varying factors. Then, a response surface methodology procedure was adopted with a central composite design to optimize further the extraction process in order to maximize the TPC. We found that the use of convection drying at 70 °C for 8 hours gave the extract with the highest TPC and antioxidant activities. Optimal extraction parameters were found as follows: ethanol with a concentration of 56.0% as the solvent, material-to-solvent ratio of 1/38.0 g/mL, extraction time of 67.2 minutes, material size ≤0.5 mm, temperature 60 °C, through 1 extraction cycle, and with a stirring speed of 300 rpm. Under the optimized conditions, the experimental value for TPC was 2.9 mg gallic acid equivalent (GAE)/g dry weight (DW), which is reasonably close to the value predicted by the model (2.8 mg GAE/g DW). The half-maximal inhibitory concentration (IC50) values determined by the 2,2-diphenyl-1-picrylhydrazyl and 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid free radical tests of the CJR extract obtained under optimal conditions were 1042.3 and 299.0 µg/mL, respectively.

Application of Fe-based metal-organic framework and its pyrolysis products for sulfonamide treatment

The occurrence and fate of antibiotic compounds in water can adversely affect human and animal health; hence, the removal of such substrates from soil and water is indispensable. Herein, we described the synthesis method of mesoporous carbon (MPC) via the pyrolysis route from a coordination polymer Fe-based MIL-53 (or MIL-53, shortly). The MPC structure was analyzed by several physical techniques such as SEM, TEM, BET, FT-IR, VSM, and XRD. The response surface methodology (RSM) was applied to find out the effects of initial concentration, MPC dosage, and pH on the removal efficiency of trimethoprim (TMP) and sulfamethoxazole (SMX) antibiotics in water. Under the optimized conditions, the removal efficiencies of TMP and SMX were found to be 87% and 99%, respectively. Moreover, the adsorption kinetic and isotherm studies showed that chemisorption and the monolayer adsorption controlled the adsorption process. The leaching test and recyclability studies indicated that the MPC structure was stable and can be reused for at least four times without any considerable change in the removal efficiency. Plausible adsorption mechanisms were also addressed in this study. Because of high maximum adsorption capacity (85.5 mg/g and 131.6 mg/g for TMP and SMX, respectively) and efficient reusability, MPC is recommended to be a potential adsorbent for TMP and SMX from water media.

Kinetics, Isotherm, Thermodynamics, and Recyclability of Exfoliated Graphene-Decorated MnFe2O4 Nanocomposite Towards Congo Red Dye

Herein, we described the use of exfoliated graphene- (EG-) decorated magnetic MnFe2O4 nanocomposite (EG@MnFe2O4) for the removal and adsorption of Congo red (CR) dye from wastewater. Firstly, the precursors (EG, MnFe2O4) and EG@MnFe2O4 were fabricated, characterized using several physical analytical techniques such as X-ray powder diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), and N2adsorption/desorption isotherm measurement. For the adsorption experiments, the effect of contact time (0–240 min), concentration (10–60 mg/L), solution pH (2–10), adsorbent dosage (0.03–0.07 g), and temperature (283–313 K) was rigorously studied. To elucidate the adsorption mechanism and behaviour of CR over EG@MnFe2O4 and MnFe2O4 adsorbents, the kinetic models (pseudo-first-order, pseudo-second-order, Elovich, and Bangham) and isotherm models (Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich) have been adopted. The kinetic results indicated that models adhered to the pseudo-second-order equation, exhibiting the chemisorption mechanism in heterogeneous phrase. Meanwhile, the isotherm results revealed the adsorption of CR over EG@MnFe2O4 obeyed the monolayer behaviour (Langmuir model) rather than multilayer behaviour (Freundlich equation) over MnFe2O4. The thermodynamic study also suggested that such adsorption was an endothermic and spontaneous process. With high maximum adsorption capacity (71.79 mg/g) and good recyclability (at least 4 times), EG@MnFe2O4 can be a potential alternative for the adsorptive removal of CR dye from water.

Process Optimization by a Response Surface Methodology for Adsorption of Congo Red Dye onto Exfoliated Graphite-Decorated MnFe2O4 Nanocomposite: The Pivotal Role of Surface Chemistry

Natural graphite, a locally available, eco-friendly, and low-cost carbonaceous source, can be easily transformed into exfoliated graphite (EG) with many surface functional groups via a chemical oxidation route. Combination between EG and magnetic MnFe2O4 is a promising strategy to create a hybrid kind of nanocomposite (EG@MnFe2O4) for the efficient adsorptive removal of Congo red (CR) dye from water. Here, we reported the facile synthesis and characterization of chemical bonds of EG@MnFe2O4 using several techniques such as Fourier-transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS). In particular, the quantity method by Boehm titration was employed to identify the content of functional groups: Carboxylic acid (0.044 mmol/g), phenol (0.032 mmol/g), lactone (0.020 mmol/g), and total base (0.0156 mmol/g) on the surface of EG@MnFe2O4. Through the response surface methodology-optimized models, we found a clear difference in the adsorption capacity between EG-decorated MnFe2O4 (62.0 mg/g) and MnFe2O4 without EG decoration (11.1 mg/g). This result was also interpreted via a proposed mechanism to elucidate the contribution of surface functional groups of EG@MnFe2O4 to adsorption efficiency towards CR dye.

Combined Minimum-Run Resolution IV and Central Composite Design for Optimized Removal of the Tetracycline Drug Over Metal⁻Organic Framework-Templated Porous Carbon

In this study, a minimum-run resolution IV and central composite design have been developed to optimize tetracycline removal efficiency over mesoporous carbon derived from the metal-organic framework MIL-53 (Fe) as a self-sacrificial template. Firstly, minimum-run resolution IV, powered by the Design-Expert program, was used as an efficient and reliable screening study for investigating a set of seven factors, these were: tetracycline concentration (A: 5-15 mg/g), dose of mesoporous carbons (MPC) (B: 0.05-0.15 g/L), initial pH level (C: 2-10), contact time (D: 1-3 h), temperature (E: 20-40 °C), shaking speed (F: 150-250 rpm), and Na+ ionic strength (G: 10-90 mM) at both low (-1) and high (+1) levels, for investigation of the data ranges. The 20-trial model was analyzed and assessed by Analysis of Variance (ANOVA) data, and diagnostic plots (e.g., the Pareto chart, and half-normal and normal probability plots). Based on minimum-run resolution IV, three factors, including tetracycline concentration (A), dose of MPC (B), and initial pH (C), were selected to carry out the optimization study using a central composite design. The proposed quadratic model was found to be statistically significant at the 95% confidence level due to a low P-value (<0.05), high R2 (0.9078), and the AP ratio (11.4), along with an abundance of diagnostic plots (3D response surfaces, Cook's distance, Box-Cox, DFFITS, Leverage versus run, residuals versus runs, and actual versus predicted). Under response surface methodology-optimized conditions (e.g., tetracycline concentration of 1.9 mg/g, MPC dose of 0.15 g/L, and pH level of 3.9), the highest tetracycline removal efficiency via confirmation tests reached up to 98.0%-99.7%. Also, kinetic intraparticle diffusion and isotherm models were systematically studied to interpret how tetracycline molecules were absorbed on an MPC structure. In particular, the adsorption mechanisms including "electrostatic attraction" and "π-π interaction" were proposed.

A hollow mesoporous carbon from metal-organic framework for robust adsorbability of ibuprofen drug in water

Herein, we described a tunable method for synthesis of novel hollow mesoporous carbon (MPC) via direct pyrolysis (800^oC) of MIL-53 (Fe) as a self-sacrificed template. The structural characterization revealed a hollow, amorphous, defective and mesoporous MPC along with high surface area (approx. 200 m² g^-1). For the experiments of ibuprofen adsorption onto MPC, effects of contact time, MPC dosage, ionic strength, concentration and temperature were systematically investigated. The optimal conditions consisted of pH = 3, concentration 10 mg l^-1 and dose of 0.1 g l^-1 for the highest ibuprofen removal efficiency up to 88.3% after 4 h. Moreover, adsorption behaviour, whereby chemisorption and monolayer controlled the uptake of ibuprofen over MPC, were assumed. Adsorption mechanisms including H-bonding, π-π interaction, metal-oxygen, electrostatic attraction were rigorously proposed. In comparison to several studies, the MPC nanocomposite in this work obtained the outstanding maximum adsorption capacity (206.5 mg g^-1) and good reusability (5 cycles); thus, it can be used as a feasible alternative for decontamination of ibuprofen anti-inflammatory drug from water.

Mechanistic investigation of ciprofloxacin recovery by magnetite-imprinted chitosan nanocomposite: Isotherm, kinetic, thermodynamic and reusability studies

Recovery of antibiotics from water and wastewaters has recently gained a great deal of attention due to their serious health and environmental problems. In this work, a magnetite imprinted chitosan polymer nanocomposites (Fe-CS NCs) were synthesized and applied for the adsorptive removal of ciprofloxacin (CIFO) as a model fluoroquinolone antibiotics. The composition and surface morphology of Fe-CS NCs were studied by SEM, BET, XRD, TEM, FTIR and zeta potential meter. Modelling and optimization of adsorption process were studied using response surface methodology (RSM). The reliability of the RSM models was tested by fitting the data. A comparative analysis of the results derived from the models demonstrated that the second-order model was the best. From the contour plotting results, at pH < pH_iep low adsorption rate was observed due to protonation of the chitosan NH₂ groups, whereas the adsorption rate was significantly enhanced and achieved to a maximum level at pH 6 due to the electrostatic interactions and hydrophobic interactions. Under optimum conditions, maximum removal efficiency and maximum adsorption capacity were obtained 68% and 142 mg/g, respectively. Well regenerability of Fe-CS together with its high capacity of fluoroquinolone antibiotics removal provide a promisable strategy to remediation of wastewaters.

Metal-Organic Framework MIL-53(Fe) as an Adsorbent for Ibuprofen Drug Removal from Aqueous Solutions: Response Surface Modeling and Optimization

Ibuprofen contamination from water sources has been increasingly alarming due to its environmentally accumulative retention; however, the strategies for ibuprofen-containing water treatment are still an enormous challenge. Herein, we described the utilization of metal-organic frameworks MIL-53(Fe) (MIL = Materials of Institute Lavoisier) for the adsorption of ibuprofen in synthetic solution. Firstly, the MIL-53(Fe) was solvothemally synthesized and then characterized using the X-ray diffraction and Fourier-transform infrared spectroscopy techniques. The optimization of ibuprofen adsorption over MIL-53(Fe) was performed with three independent variables including ibuprofen concentration (1.6–18.4 mg/L), adsorbent dosage (0.16–1.84 g/L), and pH (2.6–9.4) according to the experimental design from response surface methodology. Under the optimized conditions, more than 80% of ibuprofen could be eliminated from water, indicating the promising potential of the MIL-53(Fe) material for treatment of this drug. Kinetic and isotherm models also were used to elucidate the chemisorption and monolayer behavior mechanisms of ibuprofen over MIL-53(Fe).

Tunable Synthesis of Mesoporous Carbons from Fe₃O(BDC)₃ for Chloramphenicol Antibiotic Remediation

Chloramphenicol (CAP) is commonly employed in veterinary clinics, but illegal and uncontrollable consumption can result in its potential contamination in environmental soil, and aquatic matrix, and thereby, regenerating microbial resistance, and antibiotic-resistant genes. Adsorption by efficient, and recyclable adsorbents such as mesoporous carbons (MPCs) is commonly regarded as a "green and sustainable" approach. Herein, the MPCs were facilely synthesized via the pyrolysis of the metal⁻organic framework Fe₃O(BDC)₃ with calcination temperatures (x °C) between 600 and 900 °C under nitrogen atmosphere. The characterization results pointed out mesoporous carbon matrix (MPC700) coating zero-valent iron particles with high surface area (~225 m²/g). Also, significant investigations including fabrication condition, CAP concentration, effect of pH, dosage, and ionic strength on the absorptive removal of CAP were systematically studied. The optimal conditions consisted of pH = 6, concentration 10 mg/L and dose 0.5 g/L for the highest chloramphenicol removal efficiency at nearly 100% after 4 h. Furthermore, the nonlinear kinetic and isotherm adsorption studies revealed the monolayer adsorption behavior of CAP onto MPC700 and Fe₃O(BDC)₃ materials via chemisorption, while the thermodynamic studies implied that the adsorption of CAP was a spontaneous process. Finally, adsorption mechanism including H-bonding, electrostatic attraction, π⁻π interaction, and metal⁻bridging interaction was proposed to elucidate how chloramphenicol molecules were adsorbed on the surface of materials. With excellent maximum adsorption capacity (96.3 mg/g), high stability, and good recyclability (4 cycles), the MPC700 nanocomposite could be utilized as a promising alternative for decontamination of chloramphenicol antibiotic from wastewater.

Optimization of Microwave-Assisted Extraction of Essential Oil from Vietnamese Basil (Ocimum basilicum L.) Using Response Surface Methodology

Basil plant is a common source for linalool and estragole. However, it has been showed that the chemical composition of basil varies considerably depending on many factors including method of extraction, cultivar of the plant or geographical location. In this study, we attempted to extract essential oil from Vietnamese basil and analyze the chemical composition of the obtained oil using gas chromatography–mass spectrometry (GC-MS). The extraction method of choice was microwave-assisted hydro-distillation (MAHD) and the process was optimized with Response Surface Methodology (RSM) with regard to four experimental parameters including raw material size, raw material to water ratio, extraction time and microwave power. The results showed that ground basil leaves, when extracted with optimal conditions of water-to-material ratio of 3.2:1, extraction time of 97 (min) and microwave power of 430 (W), gave the actual essential oil yield of 0.6%. Regarding ANOVA results of the quadratic model, high determination coefficient (R2 = 0.9077), significant F-value of 10.92 and the p-value of less than 0.05 indicate that this model is significant between experimental and predicted variables, and should be fixed. In addition, GC-MS analysis revealed that major components of Vietnamese Basil were Estragole (87.869%), α-Bergamotene (2.922%), τ-Cadinol (2.770%), and Linalool (1.347%).

Effective Photocatalytic Activity of Mixed Ni/Fe-Base Metal-Organic Framework under a Compact Fluorescent Daylight Lamp

Mixed Ni/Fe-base metal-organic framework (Ni/Fe-MOF) with different molar ratios of Ni2+/Fe3+ have been successfully produced using an appropriate solvothermal router. Physicochemical properties of all samples were characterized using X-ray diffraction (XRD), Raman, field emission scanning electron microscopes (FE-SEM), fourier-transform infrared spectroscopy (FT-IR), N2 adsorption-desorption analysis, X-ray photoelectron spectroscopy (XPS), ultraviolet-visible diffuse reflectance spectra (UV-Vis DRS), and photoluminescence spectra (PL). The photocatalytic degradation performances of the photocatalysts were evaluated in the decomposition of rhodamine B (RhB) under a compact fluorescent daylight lamp. From XRD, IR, XPS, and Raman results, with the presence of mixed ion Fe3+ and Ni2+, MIL-88B (MIL standing for Materials of Institut Lavoisier) crystals based on the mixed metal Fe2NiO cluster were formed, while MIL-53(Fe) was formed with the presence of single ion Fe3+. From UV-Vis DRS results, Ni/Fe-MOF samples exhibited the absorption spectrum up to the visible region, and then they showed the high photocatalytic activity under visible light irradiation. A Ni/Fe-MOF sample with a Ni2+/Fe3+ molar ratio of 0.3 showed the highest photocatalytic degradation capacity of RhB, superior to that of the MIL-53(Fe) sample. The obtained result could be explained as a consequence of the large surface area with large pore volumes and pore size by the Ni2+ incorporating into the MOF’s structure. In addition, a mixed metal Fe/Ni-based framework consisted of mixed-metal cluster Fe2NiO with an electron transfer effect and may enhance the photocatalytic performance.

Removal of Cu2+ from Aqueous Water by Adsorption onto the Efficient and Recyclable Durian Shell-Derived Activated Carbon

We investigated the use of durian shell-derived activated carbon (DSAC) for the removal of Cu2+. To determine the optimal condition for Cu2+ removal, the response surface methodology (RSM) was used to establish a second-order polynomial model with variables such as Cu2+ concentration (Ci), adsorbent dosage (dDSAC) and pH. With R2 = 0.9847 and P-value < 0.0001, the model was proved to be statistically significant. The RSM based confirmation test revealed that the removal of Cu2+ was maximum (99.6%) at optimal conditions: Ci = 61.6 mg/L, dDSAC = 5.0 g/L and pH = 5.2. Based on calculated R2, data fitness for adsorption isotherms were positioned as follows: Langmuir > Tempkin > Freundlich. In other words, monolayer adsorption was the most favorable behavior with maximum capacity of 76.92 mg/g from Langmuir model. Interestingly, DSAC was reused at least five times without a considerable decrease of Cu2+ removal efficiency. Therefore, durian shell can be used as a highly effective, reusable and promising raw material to fabricate the activated carbon.