Effect of cycle run time of backwash and relaxation on membrane fouling removal in submerged membrane bioreactor treating sewage at higher flux

Optimization of membrane filtration and cleaning strategy in a high solid thermophilic AnMBR treating food waste

Anaerobic membrane bioreactor is advantageous over traditional processes for food waste treatment, i.e. short retention time, high loading rate, and particulate clean permeate. However, establishing a sustainable membrane filtration is a long-standing challenge because of its high viscosity and solids concentration characteristics. Therefore, this study investigated the changes in the membrane permeability before and after the cleaning during a 130-day thermophilic anaerobic experiment. Results show that the AnMBR system could maintain high stability even under a short HRT of 10 days and OLR of 9.0 kg-COD/(m3·d) with low volatile fatty acid of 50 mg/L. The membrane filtration deteriorates with the concurrence of a sharp increase of viscosity when the volatile solids reached 23 g/L. A critical flux was achieved at 5.5 L/(m2·h) under optimized operation conditions, membrane filtration/relaxing ratio with less than 4:1 at a hydraulic retention time of 15 d. Membrane fouling can be removed by soaking the membrane in NaClO (1 g/L, 15 h) and citric acid (2 g/L, 2 h). Conclusively, this work provides insight to establish the operation strategy for a thermophilic AnMBR treating food waste.

Fouling reduction in nanofiltration membranes in the treatment of municipal sewage - effect of coagulant type used for prior chemically enhanced primary treatment

The limiting factor in wide-scale application of membranes for wastewater treatment is membrane fouling. Coagulation has emerged as an effective technique for fouling control. In this research, municipal wastewater was treated using a two-stage treatment. In stage-1, chemically enhanced primary treatment (CEPT) was rendered using an optimum dose of two coagulants, i.e. alum, ferric chloride and a 1:1 mix of both. The optimum doses for coagulants were determined using a jar test. In stage-2, a nanofiltration (NF) membrane was used to further treat the effluent from stage-1. In CEPT, the 1:1 mixture of coagulants showed maximum removals, i.e. 75-77% for the total suspended solids and 73-75% for the chemical oxygen demand (COD). Stage-2 provided 85-95% removals for turbidity (0.88 nephelometric turbidity units), COD (41 mg/L), total dissolved solids (101 mg/L), hardness (11 mg/L as CaCO₃), chlorides (80 mg/L), and heavy metals (copper [0.03 mg/L] and lead [0.02 mg/L]). The operational time of the NF membrane was 46 min, 55 min and 70 min using alum, ferric chloride, and mix (1:1), respectively. Significant reduction was observed in membrane fouling for 1:1 mixture of coagulants. The effluent met the US Environmental Protection Agency guidelines for non-potable reuse.

Experimental Investigation of the Novel Periodic Feed Pressure Technique in Minimizing Fouling during the Filtration of Oily Water Systems Using Ceramic Membranes

Fouling represents a bottleneck problem for promoting the use of membranes in filtration and separation applications. It becomes even more persistent when it comes to the filtration of fluid emulsions. In this case, a gel-like layer that combines droplets, impurities, salts, and other materials form at the membrane's surface, blocking its pores. It is, therefore, a privilege to combat fouling by minimizing the accumulation of these droplets that work as seeds for other incoming droplets to cluster and coalesce with. In this work, we explore the use of the newly developed and novel periodic feed pressure technique (PFPT) in combating the fouling of ceramic membranes upon the filtration of oily water systems. The PFPT is based on alternating the applied transmembrane pressure (TMP) between the operating one and zero. A PFPT cycle is composed of a filtration half-cycle and a cleaning half-cycle. Permeation occurs when the TMP is set at its working value, while the cleaning occurs when it is zero. Three PFPT patterns were examined over two feeds of oily water systems with oil contents of 100 and 200 ppm, respectively. The results show that the PFPT is very effective in minimizing the problem of fouling compared to a non-PFPT normal filtration. Furthermore, the overall drops in permeate flux during the cleaning half-cycles are compensated by appreciable enhancement due to the significant elimination of fouling development such that the overall production of filtered water is even increased. Inspection of the internal surface of the membrane post rinsing at the end of the experiment proves that all PFPT cycles maintained the ceramic membranes as clean after a 2-h operation. This can ensure a prolonged lifespan of the ceramic membrane use and a continuous greater permeate volume production. The advantage of the PFPT is that it can be implemented on existing units with minimal modification, ease of operation, and saving energy.

Temperature and immigration effects on quorum sensing in the biofilms of anaerobic membrane bioreactors

Quorum sensing (QS), a microbial communication mechanism modulated by acyl homoserine lactone (AHL) molecules impacts biofilm formation in bioreactors. This study investigated the effects of temperature and immigration on AHL levels and biofouling in anaerobic membrane bioreactors. The hypothesis was that the immigrant microbial community would increase the AHL-mediated QS, thus stimulating biofouling and that low temperatures would exacerbate this. We observed that presence of immigrants, especially when exposed to low temperatures indeed increased AHL concentrations and fouling in the biofilms on the membranes. At low temperature, the concentrations of the main AHLs observed, N-dodecanoyl-L-homoserine lactone and N-decanoyl-L-homoserine lactone, were significantly higher in the biofilms than in the sludge and correlated significantly with the abundance of immigrant bacteria. Apparently low temperature, immigration and denser community structure in the biofilm stressed the communities, triggering AHL production and excretion. These insights into the social behaviour of reactor communities responding to low temperature and influx of immigrants have implications for biofouling control in bioreactors.

Mitigation of membrane biofouling in membrane bioreactor treating sewage by novel quorum quenching strain of Acinetobacter originating from a full-scale membrane bioreactor

A novel quorum quenching (QQ) strain, Acinetobacter guillouiae ST01, was isolated from a full-scale membrane bioreactor (MBR) and characterized for its QQ activities. Batch reactor studies at lab-scale showed that A. guillouiae ST01 exhibited higher QQ activity against acyl homoserine lactones (AHLs) with an oxo group compared to those without an oxo group. The organism was then inoculated (10%) in an MBR (Q-MBR) treating sewage over 48 days and was found to reduce quorum sensing (QS) activity by reducing AHL concentrations in the sludge and the biofilm of the Q-MBR. The concentration of polysaccharides was reduced up to 30% in both the biofilm and sludge relative to the control, whereas protein concentrations were reduced by 40% and 47% in the sludge and biofilm, respectively. The Q-MBR fouling rates were halved. These results indicate that A. guillouiae ST01 is a promising strain for biofouling reduction in MBR treating real wastewater.

Quorum sensing and quenching in membrane bioreactors: Opportunities and challenges for biofouling control

Membrane biofouling, due to biofilm growth after planktonic bacteria attachment to a membrane, is a major bottleneck limiting the energy-efficient operation and maintenance of membrane bioreactors (MBRs). Microbial communications, known as quorum sensing (QS), are responsible for this biofouling behavior. Novel strategies for stopping this communication, known as quorum quenching (QQ), appear to be successful for biofouling control in MBRs used for wastewater treatment. This review describes recent information regarding the signal molecules and mechanisms responsible for QS behaviors, promising approaches for QQ (enzymatic, bacterial, fungal, photocatalytic, mimicking, and biostimulating methods), and efficient fabrication and use of QQ media for MBR applications. We discuss the opportunities and challenges of QQ techniques for their further improvement and practical use in MBRs.