Review on some metal oxide nanoparticles as effective adsorbent in wastewater treatment

Photodecoration of tungsten oxide nanoparticles onto eggshell as an ultra-fast adsorbent for removal of MB dye pollutant

Nowadays, the use of natural wastes and adsorbents along with their modification by simple and new methods based on metal oxides to remove dye pollutants has been the focus of many researchers. In this study, for the first time, simple and low-cost modification of eggshell (EGS) with tungsten oxide (WO3) based on the photochemical modification method as a green, ultra-fast, cost-effective, and biodegradable adsorbent is reported to remove of methylene blue (MB) dye pollutant. The EGS modified by WO3 was investigated by EDX, EDX mapping, XRD, FE-SEM, and UV-Vis Diffuse Reflectance (DRS) analyses. The obtained results show that the modified EGS by WO3 has more than ten times (78.5%) the ability to remove MB dye pollutant within 3 min compared to bare EGS (11%). Various parameters including dye pollutant pH, dye concentration, adsorbent dosage, and reusability of the WO3/EGS adsorbent for removal of MB dye pollutant were investigated and the result show that the adsorbent capacity of WO3/EGS is 1.64 mg g-1. EGS adsorbent The synthesis of WO3/EGS adsorbent with a novel photochemical method as a fast and very cheap adsorbent with excellent efficiency can be a promising alternative adsorbent for various purposes in removing dye pollutants from water environments.

Structural Analysis and Adsorption Studies of (PbO, MgO) Metal Oxide Nanocomposites for Efficient Methylene Blue Dye Removal from Water

In the present work, magnesium oxide (MgO) and lead oxide (PbO) nanoparticles were prepared by the co-precipitation method. Their structural parameters and morphology were investigated using XRD, HRTEM, and FTIR. The formation of the phases was seen to have small average crystallite sizes and an orthorhombic crystal structure for both MgO and PbO nanoparticles. The results of HR-TEM showed irregularly shaped nanoparticles: quasi-spherical or rod-like shapes and spherical-like shapes for MgO and PbO nanoparticles, respectively. The produced nanoparticles' size using X-ray diffraction analysis was found to be 17 nm and 41 nm for MgO and PbO nanoparticles, respectively. On the other hand, it was observed from the calculations that the optical band gap obeys an indirect allowed transition. The calculated values of the band gap were 4.52 and 4.28 eV for MgO and PbO NPs, respectively. The MB was extracted from the wastewater using the prepared composites via absorption. Using a variety of kinetic models, the adsorptions were examined. Out of all the particles, it was discovered that the composites were best. Furthermore, of the models currently under consideration, the pseudo-second-order model best fit the degradation mechanism. The resultant composites could be beneficial for degrading specific organic dyes for water purification, as well as applications needing a wider optical band gap.

A critical and comprehensive review of the current status of 17β-estradiol hormone remediation through adsorption technology

Even at low concentrations, steroid hormones pose a significant threat to ecosystem health and are classified as micropollutants. Among these, 17β-estradiol (molecular formula: C18H24O2; pKa = 10.46; Log Kow = 4.01; solubility in water = 3.90 mg L-1 at 27 °C; molecular weight: 272.4 g mol-1) is extensively studied as an endocrine disruptor due to its release through natural pathways and widespread use in conventional medicine. 17β-estradiol (E2) is emitted by various sources, such as animal and human excretions, hospital and veterinary clinic effluents, and treatment plants. In aquatic biota, it can cause issues ranging from the feminization of males to inhibiting plant growth. This review aims to identify technologies for remediating E2 in water, revealing that materials like graphene oxides, nanocomposites, and carbonaceous materials are commonly used for adsorption. The pH of the medium, especially in acidic to neutral conditions, affects efficiency, and ambient temperature (298 K) supports the process. The Langmuir and Freundlich models aptly describe isothermal studies, with interactions being of a low-energy, physical nature. Adsorption faces limitations when other ions coexist in the solution. Hybrid treatments exhibit high removal efficiency. To mitigate global E2 pollution, establishing national and international standards with detailed guidelines for advanced treatment systems is crucial. Despite significant advancements in optimizing technologies by the scientific community, there remains a considerable gap in their societal application, primarily due to economic and sustainable factors. Therefore, further studies are necessary, including conducting batch experiments with these adsorbents for large-scale treatment along with economic analyses of the production process.

Humic acid-nanoceria composite as a sustainable adsorbent for simultaneous removal of uranium(VI), chromium(VI), and fluoride ions from aqueous solutions

In this article, the multifunctional behavior of novel, efficient, and cost-effective humic acid-coated nanoceria (HA@CeO2 NPs) was utilized for the sorptive removal of U(VI), Cr(VI), and F- ions at different conditions. The production cost of HA@CeO2 was $19.28/kg and was well characterized by DLS, FESEM, HRTEM, FTIR, XRD, XPS, and TGA. Batch adsorption study for U(VI) (at pH ~ 8), Cr(VI) (at pH ~ 1), and F- (at pH ~ 2) revealed that the maximum percentage of sorption was > 80% for all the cases. From the contact time experiment, it was concluded that pseudo-second-order kinetics followed, and hence, the process should be a chemisorption. The adsorption study revealed that U(VI) and Cr(VI) followed the Freundlich isotherm, whereas F- followed the Langmuir isotherm. Maximum adsorption capacity for F- was 96 mg g-1. Experiments in real water suggest that adsorption is decreased in Kaljani River water (~ 12% for Cr(VI) and ~ 11% for F-) and Kochbihar Lake water (25.04% for Cr(VI) and 20.5% for F-) because of competing ion effect. Mechanism was well established by the kinetic study as well as XPS analysis. Because of high adsorption efficiency, HA@CeO2 NPs can be used for the removal of other harmful water contaminants to make healthy aquatic life as well as purified drinking water.

Adsorption and Desorption Study of Reusable Magnetic Iron Oxide Nanoparticles Modified with Justicia adhatoda Leaf Extract for the Removal of Textile Dye and Antibiotic

The release of tetracycline hydrochloride (TCH) and methylene blue (MB) dye into the aquatic system uncontrollably caused major environmental and health problems; hence, their prevention required serious attention. Adsorption process is now being researched in order to increase adsorption efficiency and reprocess to alleviate environmental issues. The use of magnetic nanoparticle as an adsorbent for wastewater treatment has a lot of prospective. A magnetic iron oxide nanoparticle surface modified by Vasaka (Justicia adhatoda) leaf extract (JA-MIONs) is used to give a fast removal approach for MB dye and TCH antibiotics. Dynamic light scattering, UV-Vis and band gap measurement, powder X-ray diffraction, Fourier-transform infrared spectroscopy, and transmission electron microscopy were operated to analyse the formation and size of these magnetic nanoparticles. The impacts of different factors such as contact time (30-150 min), adsorbate concentration (10-50 mg/L), pH (4-10), and adsorbent dose (2-10 mg) were explored. Adsorption kinetics and isotherms show that it follows the pseudo-first-order kinetic and the Freundlich isotherm, with maximum adsorption capacities of 76.92 mg/g for MB and 200 mg/g for TCH at 298 K. The reusability of the JA-MIONs eventually exhibited a decline in the adsorption percentage of MB and TCH after five and four times respectively. After the desorption-adsorption cycles, this adsorbent continued to exhibit significant adsorption capacity. This investigation furnished the significant reference data for the synthesis of JA-MIONs as a novel and auspicious adsorbent for the industrial clean-up of toxic dyes and heavily used antibiotics from water.

Fixed-Bed Column Adsorption Studies: Comparison of Alginate-Based Adsorbents for La(III) Ions Recovery

The paper investigated the adsorption of the packed-bed column with the alginate-based adsorbents (ALG-based adsorbents) such as alginate-biochar, alginate-clinoptilolite, alginate-lignin, and alginate-cellulose for La(III) ions' removal. Fixed-bed adsorption studies with various alginate-based adsorbents were carried out and compared to the La(III) ions adsorption. The columns were filled with ALG-based adsorbent beads of approximately 1.1 ± 0.005 mm spherical shapes. The effects of the inlet concentrations on the breakthrough curves were studied in terms of the adsorption performance of the ALG-based adsorbents. The experimental data were correlated with the Adams-Bohart, Yoon-Nelson, Thomas, and Wolborska models to determine the best operational parameters. Based on the comparison of R² values, the Thomas and Yoon-Nelson models were found to be more suitable than the Adams-Bohart and Wolborska models. In the desorption study, the ALG-based adsorbents packed columns showed the maximum desorption of La(III) just after passing 100 cm³ of 1 mol/dm³ HCl. Overall, the results show that ALG-based adsorbents could be used for continuous recovery of La(III) ions from aqueous solutions and were not only cost-effective but also environmentally friendly.

Proficient exclusion of pesticide using humic acid-modified magnetite nanoparticles from aqueous solution

Extensive dispersal of the pesticides to shield the different types of vegetation from pests has increased the production but at the same it has resulted in an increase in environmental pollution. Consequently, it is necessary to eliminate these undesired pollutants from the environment. The current investigation offers the synthesis of humic acid-coated magnetite nanoparticles towards effective removal of the most common insecticide, imidacloprid, from aqueous solution using a batch adsorption method. These synthesized nanoparticles were characterized with the help of several analytical and spectroscopic techniques. To acquire the maximum conceivable adsorption, effects of different influencing parameters like pH of the solution, time of contact, concentration of pesticide solution, amount of adsorbent and temperature were also examined. Moreover, the kinetic studies were found to be in good agreement with a pseudo-second-order kinetic model supporting the occurrence of chemisorption phenomenon. Additionally, isotherm modeling proved that the adsorption process was in accordance with the Langmuir model of isotherm. Thermodynamic parameters depicted the endothermic and spontaneous behavior of the adsorption process. Desorption studies were also carried out to examine the reusability of these nano-adsorbents. These verdicts confirmed that the surface modified magnetite nanoparticles may be treated as proficient material for exclusion of imidacloprid from the aqueous solution.

Synthesis of powdered and beaded chitosan materials modified with ZnO for removing lead (II) ions

Lead contamination in wastewater may affect aquatic organisms, the environment, and human consumption because it is a highly toxic metal that caused human health effects. Thus, it is recommended to remove lead before releasing it into the environment. Powdered and beaded chitosan materials modified with ZnO were synthesized and investigated by various characterized techniques. Lead removal efficiencies of chitosan materials were studied by batch experiments, adsorption isotherms, and kinetics. Chitosan powder (CP), chitosan beads (CB), chitosan beads mixed ZnO (CZB), and chitosan beads coated ZnO (ZCB) were synthesized. CP represented a semi-crystalline structure while CB was an amorphous structure. CZB and ZCB were semi-crystalline structures with ZnO peaks. CP was a scaly-sheet and coarse surface while CB, CZB, and ZCB were sphere shapes with scaly-sheet surfaces. C, O, and N were the main chemical elements in chitosan materials, and Zn was detected in CZB and ZCB. O-H, N-H, and C-O were the main functional groups of chitosan materials. All chitosan materials had high lead removal efficiencies of more than 92%, and Freundlich and pseudo-second-order kinetic models well explained their adsorption patterns and mechanisms. Therefore, both adding metal oxide and changing material form are recommended for improving material efficiency, and ZCB was a good offer for further industrial applications.