Immediate adhesive properties to dentin and enamel of a universal adhesive associated with a hydrophobic resin coat

Effect of multi-layer applications of self-etch universal bonding agents on the adhesion of resin composite to enamel

To evaluate the effect of adhesive coats application on the enamel microtensile bond strength (µTBS) of universal adhesives, morphological etching pattern and their chemical interaction with hydroxyapatite (HA). Two universal adhesives were investigated: Scotchbond Universal (SBU, 3 M) and Prime&Bond Universal (PBU, Dentsply). The adhesives were applied in self-etching mode on bovine enamel (n = 8) in one (1L), two (2L) or three coats (3L) and light-cured as per manufacturers' instructions. As controls adhesives were applied to etched enamel (H3PO4-37% phosphoric acid). Bonded specimens were cut into sticks that were stored in deionized water for 24 h or 6 months prior to µTBS testing. Two-way ANOVA and Tukey's test were used for statistical analysis of bond strength with α = 5%. For morphological SEM analysis, enamel surfaces were treated as aforementioned and immediately rinsed with acetone. The intensity of monomer-calcium salt formation from each treatment was measured via infrared spectroscopy (ATR-FTIR). All treatments presented no significant reduction on µTBS after aging (p > 0.05). However, SBU attained highest µTBS when applied in 3L. PBU showed higher µTBS when applied to H3PO4 etched enamel than 1L or 2L. Etching pattern was enhanced by 3L application, particularly with PBU. Chemical interaction was notably higher for SBU than PBU, with no relevant differences with more layers or prior H3PO4-etching. The application of three adhesive coats of universal adhesives in self-etch mode using may enhance the bonding performance and etching pattern to enamel, surpassing the H3PO4-etched enamel bond for SBU. The chemical interaction with calcium from enamel is not affected by number of coats or prior phosphoric acid etching.

Influence of different immediate dentin sealing strategies on bond strength of indirect resin nanoceramic restorations

In this study, we evaluated the effect of four different strategies for bonding a CAD/CAM resin nanoceramic restoration (Lava Ultimate, 3M) to the dentin surface using a universal adhesive (Scotch Bond Universal, 3M) and adhesive resin cement (RelyX Ultimate, 3M) on the shear bond strength (SBS) and failure mode. The strategies comprised: (i) immediate sealing, immediate bonding; (ii) immediate sealing, bonding after 2 weeks with provisional restoration; (iii) immediate sealing with flowable resin composite reinforcement and bonding after 2 weeks with provisional restoration; and (iv) no immediate sealing, and bonding after 2 weeks with provisional restoration. After bonding, all the specimens were thermocycled, shear tests were performed using a universal testing machine, and failure modes were determined using stereomicroscope and scanning electron microscopy. The highest mean SBS was recorded with immediate sealing, immediate bonding strategy. Most adhesive failures with exposed dentinal tubules were noted in specimens exposed to bonding after 2 weeks with no immediate sealing, which was associated with the lowest SBS. Mixed failures predominated in all immediate dentin sealing groups. Immediate sealing with universal adhesives improves SBS, particularly in the single-visit approach, which has shown significantly better performance, whereas the provisional phase has a negative effect.

Can a Novel Device with Pure Dry Air Increase the Shear Bond Strength of Dental Composites to Dentin? An Experimental Study

Modern conservative dentistry is taking the lead in daily clinical practice and is relying on adhesion. Whether it is a simple composite, ceramic inlays, onlays, veneers or crowns, the common factor for a successful outcome is a good bonding of these elements to dental structures. Thus, the purpose of this study was to evaluate the bond strength of resin composite to dentin when using a new device, the DENTIPURE KM™ (KM, Beirut, Lebanon), which provides a pure air flow, free of any contaminants and without humidity, when compared to other dental equipment. One hundred and eighty extracted human molars were equally divided into three groups according to the device used, the DENTIPURE KM™ (KM, Beirut, Lebanon), the KAVO™ (ESTETICA E30/E70/E80 Vision, KAVO, Biberach, Germany), or the ADEC™ (A-dec Performer 200, Newberg, OR, USA). The shear bond strength (SBS) was evaluated after 24 h of storage in distilled water on a universal testing machine. Statistical analysis was set with a level of significance at p ≤ 0.05. The results revealed that significantly different bond strength was imparted by the DENTIPURE KM™ device and the ADEC™ dental unit (p = 0.042). In conclusion, while the DENTIPURE KM™ device shows promise in providing contaminant-free air during bonding, its impact on dentin bond strength compared to devices like the KAVO™ appears minimal. Further research is needed to fully assess its potential in enhancing dentinal adhesion procedures.

Prolonged polymerization of a universal adhesive in non-carious cervical lesions: 36-month double-blind randomized clinical trial

OBJECTIVE

To evaluate the effect of prolonged (P) polymerization time of a universal adhesive system applied in etch-and-rinse (ER) or self-etch (SE) strategies on the clinical performance of restorations in non-carious cervical lesions (NCCLs), after 36 months of clinical service.

METHODS

A total of 140 restorations were randomly placed in 35 subjects according to the polymerization time groups: ER (10 s); ER-P (40 s); SE (10 s); and SE-P (40 s) at 1,200 mW/cm2. Composite resin was placed incrementally. The restorations were evaluated immediately and after 6, 12, 18, and 36 months using the FDI criteria. Data were analyzed using the Kaplan-Meier survival test for retention loss, and the Kruskal-Wallis' test for secondary outcomes (α = 0.05).

RESULTS

After 36 months, 19 restorations were lost: ER 6, ER-P 2, SE 9, SE-P 2. The retention rates were 82.3% for ER; 94.1 % for ER-P; 73.5 % for SE; and 94.1 % for SE-P, with a significant difference between ER vs. ER-P and SE vs. SE-P, as well as ER vs. SE-P and ER-P vs. SE (p < 0.0001). Minor defects were observed in 18 restorations for the marginal staining criteria: ER 5, ER-P 2, SE 8, SE-P 3; and in 33 restorations for the marginal adaptation criteria: ER 11, ER-P 4, SE 12, and SE-P 6 (p > 0.05). No restorations showed recurrence of caries or postoperative sensitivity.

CONCLUSIONS

A prolonged polymerization time of 40 s improves the clinical performance of the universal adhesive for both adhesive strategies evaluated, even after 36 months.

CLINICAL SIGNIFICANCE

Prolonging the polymerization time of a universal adhesive from 10 to 40 s has been shown to improve its clinical performance when used in NCCLs.

Does the universal adhesive's film thickness affect dentin-bonding effectiveness?

OBJECTIVES

To investigate the influence of adhesive resin application modalities on the film thickness of the adhesive resin and the effectiveness of a two-step universal adhesive (UA) bonded in self-etch (SE) bonding mode to high C-factor class-I cavity-bottom dentin.

MATERIALS AND METHODS

After application of the primer of G2-Bond Universal (G2B, GC), the adhesive resin was applied into standard class-I cavities (human molars) following four application modalities: (1) one layer, strongly air-blown; (2) one layer, gently air-blown; (3) two layers, each gently air-blown; (4) one layer, not air-blown. After being restored with composite, each tooth was sectioned to obtain one micro-specimen (n = 10), of which the adhesive resin film thickness was measured using optical microscopy. The micro-tensile bond strength (μTBS) was tested immediately or upon 100,000 thermocycles. Statistical analyses involved Kruskal-Wallis and Mann-Whitney U testing (p < 0.05).

RESULTS

G2B's μTBS was significantly affected by the adhesive resin application modality and aging. Gently air-blowing the adhesive resin resulted in significantly higher immediate μTBS than strong air-blowing or no air-blowing. No significant difference in μTBS was found between single or double gently air-blown adhesive resin applications. The adhesive resin film thickness significantly varied with the application modalities.

CONCLUSIONS

A too thin or too thick adhesive resin film thickness adversely affected bond strength of the two-step UA applied in SE mode and high C-factor condition.

CLINICAL RELEVANCE

The adhesive resin layer thickness can affect the bonding performance of two-step UAs in high C-factor cavities. Dental clinicians remain advised to avoid improper air-blowing of UAs and strictly follow the application instructions.

Effect of Extra Hydrophobic Resin Layer on Bonding of Universal Adhesive Systems to Enamel

OBJECTIVE

The objective of this study was to compare the effect of solvent in universal adhesives (UA) and the application of an extra layer of hydrophobic bonding resin on enamel shear bond strengths (SBS).

METHODS AND MATERIALS

Crowns of 224 bovine mandibular incisors were embedded in acrylic resin, wet-polished up to 600-grit silicon carbide paper and assigned to 3 UAs with different solvents (n=32): ethanol-based UA (ADU, AdheSE Universal, Ivoclar Vivadent); isopropanol-based UA (PBU, Prime&Bond Universal, Dentsply Sirona); and acetone-based UA (OPT, OptiBond Universal, Kerr Co). The same UAs were also applied with an extra layer of a hydrophobic bonding resin (HLB, Heliobond, Ivoclar Vivadent): ADU + HLB; PBU + HLB; and OPT + HLB. HLB alone was used as control. Enamel was etched with 37.5% H3PO4 (Kerr Gel Etchant, Kerr Co) for 15 seconds, rinsed with water, and air dried. UAs were applied according to the respective manufacturer's instructions. After adhesive application, composite cylinders (Filtek Z250, 3M Oral Care) were built up and light-cured (40 seconds/increment, 40 J/cm2) keeping the light tip in contact with the mold. Specimens were stored in water for 24 hours (24H) or for 6 months (6M). A knife-edged metallic rod (Ø=2.8-mm semicircular notch) loaded the composite cylinders until fracture. Mode of failure was analyzed with optical microscopy (40×). Statistics included twoway analysis of variance (ANOVA; adhesive strategy and water storage) and Tukey honestly significant difference (HSD) post hoc test (α=95%).

RESULTS

Mean enamel SBS ranged from 3.6 (±2.2) MPa (HLB/6M) to 24.7 (±7.1) MPa (ADU + HLB/6M). ANOVA revealed significant differences for adhesive strategy (p≤0.001) but no significant differences for water storage (p>0.05). All UAs resulted in similar mean enamel SBS with or without an extra layer of HLB at 24H. After 6M, only ADU resulted in higher enamel SBS when an extra layer of HLB was applied. All UAs resulted in higher mean enamel SBS than HLB (control). Most failures were adhesive exception for PBU/HLB/6M, which had mostly mixed failures.

CONCLUSIONS

UAs resulted in statistically higher enamel SBS than the nonsolvated hydrophobic bonding resin (control), regardless of the solvent in their composition. Application of an extra layer of hydrophobic bonding resin over UAs did not improve mean enamel SBS for isopropanol- and acetone-based UAs but did improve mean enamel SBS for the ethanol-based UA after 6M. Resin composite bonding to enamel using a hydrophobic bonding resin alone is not recommended.

Effect of an additional bonding resin on the 5-year performance of a universal adhesive: a randomized clinical trial

OBJECTIVES

To evaluate the effect of the application of an additional hydrophobic bonding resin on the clinical performance of a universal adhesive applied in etch-and-rinse (ER) or self-etch adhesive (SE) strategy in non-carious cervical lesions (NCCLs) after 5 years.

MATERIALS AND METHODS

Scotchbond Universal Adhesive (3M Oral Care) was applied in 134 NCCLs of 39 subjects using different adhesion approaches: 3-step ER (3-ER), 2-step ER (2-ER), 2-step SE (2-SE), and 1-step SE (1-SE). Enamel and dentin were acid etched prior to application of the universal adhesive for the 3-ER and 2-ER groups. An extra layer of a hydrophobic bonding resin was applied for groups 3-ER and 2-SE. All lesions were restored with Filtek Supreme XTE resin composite (3M Oral Care). Restorations were evaluated at baseline and at 5 years using the modified USPHS criteria. Mann-Whitney U and Wilcoxon tests were performed, and the survival rates (retention/fracture) were analyzed using Kaplan-Meier and log-rank tests (p < 0.05).

RESULTS

The recall rate was 66.7% at 5 years. The cumulative survival rate was 96.9% for 3-ER, 96.8% for 2-ER, 71.4% for 2-SE, and 81.3% for 1-SE strategies. The log-rank test was statistically significant (p = 0.006). Retention rates were 100% for both ER groups, 75% for 2-SE and 81.3% for 1-SE. At 5 years, 2- and 1-SE approaches showed similar retention rates, but lower than those for 3- and 2-ER. A significant decrease in retention rate was detected for 2-SE (p = 0.007) and 1-SE (p = 0.014) groups between baseline and 5 years. All groups, except 2-ER, showed an increase in marginal discoloration. For this parameter, significant differences were detected between 2-ER and 1-SE (p = 0.004).

CONCLUSIONS

The addition of a hydrophobic bonding resin to the recommended application sequence of Scotchbond Universal Adhesive did not improve its clinical performance in NCCLs after 5 years. Higher retention rates were measured when this adhesive was applied in ER mode.

TRIAL REGISTRATION

This manuscript is a 5-year follow-up of a randomized clinical trial that started in 2012 when there was no strong recommendation for registration in clinicaltrials.gov. The results after 36 months of clinical service were previously published in this journal.

Bond durability of a two-step adhesive with a universal-adhesive-derived primer in different etching modes under different degradation conditions

This study investigated the enamel and dentin bond durability of a two-step adhesive system, using a universal adhesive-derived primer (G2-Bond Universal [GU]), and compared it with the two conventional, two-step, self-etch adhesive systems (Clearfil SE Bond 2 [CS] and OptiBond XTR [OX]) under thermal cycling (TC) and long-term water storage (WS). The shear bond strengths to bovine enamel and dentin were determined using the etch-and-rinse and self-etch modes. Twelve specimens per test group were prepared and further divided into the following subgroups: 1) subjected to TC, 2) long-term WS, and 3) WS for 24 h (baseline). The enamel and dentin bond durability of GU was superior to those of CS and OX in different etching modes and under different degradation conditions. The latest two-step adhesive system, which utilizes universal adhesives' benefits in its primer, might offer durable clinical bonding performances and can be widely used in a clinical setting.

Efficacy of adhesive strategies for restorative dentistry: A systematic review and network meta-analysis of double-blind randomized controlled trials over 12 months of follow-up

PURPOSE

The efficacy of etch-and-rinse, selective enamel-etching, and self-etching protocols for universal adhesives in follow-ups of over 12 months was compared in a network meta-analysis.

STUDY SELECTION

Randomized controlled trials (RCTs) published from 1998 to 2022 that compared marginal staining, marginal adaptation, retention and fractures, post-operative sensitivity, or recurrence of caries that took place over 12-months post-restoration were selected. A network meta-analysis determined the performance of each adhesive protocol.

RESULTS

After screening 981 articles, 16 RCTs were subjected to data extraction. Of which, 674 patients with 2816 restorations, were included in the network meta-analysis. The pooled risk of marginal discoloration following self-etching was significantly higher than that following etch-and-rinse at over 12, 24, and 36 months, which was time-dependent. The pooled risks of unfavorable marginal adaptation and unfavorable retention and fractures following self-etching were also significantly higher than that following etch-and-rinse, with the rates of unfavorable retention and fractures in non-carious cervical lesions increasing in a time-dependent manner. The pooled risks of marginal discoloration, unfavorable marginal adaptation, retention and fractures were similar between etch-and-rinse and selective enamel-etching protocols. Post-operative hypersensitivity and recurrence of caries were not significantly different among etch-and-rinse, selective enamel-etching, and self-etching protocols.

CONCLUSIONS

In follow-ups over 12 months, esthetic and functional outcomes of restorations completed with an etch-and-rinse adhesive protocol were superior to the ones achieved with a self-etching strategy without selective enamel-etching. Selective enamel etching is recommended for self-etching systems. Biological responses were similar for all three adhesive strategies.

Experimental two-step universal adhesives bond durably in a challenging high C-factor cavity model

OBJECTIVES

To determine the bonding effectiveness of experimental 2-step universal adhesives (UAs) to high C-factor class-I cavity-bottom dentin and to assess the potential bond-strength contribution of an additional flowable composite layer.

METHODS

Three experimental 2-step UA formulations, involving the application of a 10-MDP-based primer followed by a hydrophobic adhesive resin with a 15-to-20-µm film thickness and differing only for filler, referred to as BZF-21 (silica and bioglass filler), BZF-29 (silica filler) and BZF-29_hv (higher silica-filler loading resulting in a higher viscosity), all prepared by GC, along with three representative commercial adhesives, Clearfil SE Bond 2 (C-SE2, Kuraray Noritake), G-Premio Bond (G-PrB, GC) and OptiBond FL (Opti-FL, Kerr), were comparatively investigated for their 'immediate' and 'aged' (50,000 thermocycles) micro-tensile bond strength (μTBS), when applied either in etch-and-rinse (E&R) or self-etch (SE) mode, to high C-factor class-I cavity-bottom dentin (n = 10; 10 experimental groups). Four additional experimental groups involved the extra application of the flowable composite G-ænial Universal Flo (GC), employed as an intermediate liner in combination with the adhesives BZF-29 and G-PrB and again applied both in E&R or SE mode. Statistical analysis was performed using linear mixed-effects (LME) modelling and linear regression analysis (p < 0.05).

RESULTS

All 2-step UAs performed similarly when compared to the gold-standard E&R Opti-FL and SE C-SE2 adhesives, except for the aged μTBS of BZF-29_hv applied in E&R mode, and significantly outperformed the 1-step UA G-PrB. Significant reduction in μTBS upon aging was only recorded for 2-step UAs applied in E&R mode. The extra flowable composite layer significantly improved G-PrB's μTBS.

SIGNIFICANCE

The experimental 2-step UAs revealed favorable bonding performance in the challenging high C-factor class-I cavity model, comparable to that of the multi-step gold-standard E&R and SE adhesives and superior to that of the 1-step UA investigated. An additionally applied flowable composite layer compensated for the lower bonding effectiveness of the 1-step UA in the high C-factor cavity model.

Investigation of the Effects of Adhesive Materials of Different Types and Thicknesses on Dental Tissue Stress via FEM Analysis

The aim of this study was to investigate the types and thicknesses of adhesive materials used in restorative treatment in dentistry in class I occlusal and class II disto-occlusal cavities and to examine the effects of stress distribution on enamel, dentin, restoration material, and adhesive material using the finite element stress analysis method. A 3-dimensional geometry of the tooth was obtained by scanning the extracted 26 numbered upper molar tooth with dental tomography. The 3D geometry obtained by using the Geomagic Design X 2020.0 software was divided into surfaces, and necessary arrangements were made. With the Solidworks 2013 software, 2 different cavity modeling, class I occlusal and class II disto-occlusal, with a cavity angle of 95 degrees on the 3D model, as well as 10, 30, and 50 micrometers thick, four types of adhesive materials and the modeling of the bulk-fill composite material on it were made. With finite element stress analysis, the stress distribution was analyzed using the Abaqus software. The materials used in the study are included in the simulation as isotropic linear elastic. Periodontal ligament and jawbone were not included in the analysis. A total of 600 N pressure was applied on the models. In our study, it was observed that the amount of stress on the tooth structures changed when the thickness, elastic modulus, and Poisson ratios of the adhesive material were changed. In addition, when all models are examined, it is seen that when the thickness is increased, more stress is placed on the adhesive material compared to the restoration, while when 50-micrometer-thick adhesive material is used, more stress is placed on the restoration compared to the adhesive material.

Does the Application of Additional Hydrophobic Resin to Universal Adhesives Increase Bonding Longevity of Eroded Dentin?

This paper evaluates the effect of an additional hydrophobic resin coat (extra HL) associated with universal adhesives on sound and eroded dentin and evaluated immediately or after 2 years of water storage to improve the microtensile bond strength (μTBS) and nanoleakage (NL) when compared to the use of universal adhesives only. Sixty-four molars were assigned to eight groups using the following combinations: 1. dentin substrate, including sound and eroded dentin; 2. treatment, including the control and extra HL and storage time (immediately and after two-years of storage). Two universal adhesives (Prime & Bond Active or Scotchbond Universal) were evaluated. Before restoration, half of the teeth were subjected to soft-drink erosion. Composite buildups were bonded; specimens were stored (37 °C/24 h), sectioned into resin−dentin bonded sticks and tested for microtensile bond strength and nanoleakage using SEM (immediately and after two-years of storage). Three-way ANOVA and Tukey’s test (α = 0.05%) were used. In the immediate testing, the application of extra HL did not increase microtensile bond strength values compared with the control group in either substrate (p > 0.05). However, extra HL significantly decreased nanoleakage values when applied to eroded and sound dentin (p = 0.0001). After two years, the application of extra HL produced significantly higher microtensile bond strength and lower nanoleakage values than the control group for both adhesives (p = 0.0001). In all cases, sound dentin showed higher microtensile bond strength and lower nanoleakage values than eroded dentin (p = 0.000001). An extra HL increased the bond strength and reduced nanoleakage in eroded dentin after two-years of storage.

The Effect of Radiotherapy on the Marginal Adaptation of Class II Direct Resin Composite Restorations: A Micro-computed Tomography Analysis

This laboratory study was designed to evaluate the marginal adaptation of Class II mesio-occluso-distal (MOD) restorations at the cervical region with micro-computed tomography (micro-CT). Two groups of restorations were compared: 1) those that had been exposed to radiotherapy before restoration was performed using a universal adhesive in etch-and-rinse and self-etch modes; and 2) those that had previously been restored using a universal adhesive in etch-and-rinse and self-etch modes and had subsequently undergone radiotherapy. Sixty intact human molars were randomly divided into groups according to irradiation status: no radiotherapy (control group); radiotherapy followed by restoration (radiotherapy-first group); and restoration followed by radiotherapy (restoration-first group). These three groups were then subdivided into two groups each on the basis of adhesive application type (etch-and-rinse and self-etch modes), for a total of six groups (n=10/group). Standardized Class II MOD cavities were prepared. A universal adhesive (Clearfil Universal Bond Quick, Kuraray, Okayama, Japan) was applied. The teeth were restored with resin composite (Estelite Posterior Quick, Tokuyama, Tokyo, Japan). The radiotherapy protocol was conducted with 60 gray (Gy) at 2 Gy/day, five days a week for six weeks. Adhesive defects were analyzed in distal and mesial views and evaluated with micro-CT (SkyScan 1174v2, Kontich, Antwerp, Belgium) on the basis of the volume of black spaces between the cavity walls and the restorative materials (mm3). The data were analyzed using the Kruskal-Wallis, Mann Whitney U and Wilcoxon tests (p<0.05). The radiotherapy protocol did not affect the marginal adaptation of the universal adhesive at the cervical regions. Regarding the application modes, for the radiotherapy-first group, the self-etch mode caused significantly higher adhesive defects than the etch-and-rinse mode at the dentin margin. For the no-radiotherapy group, the adhesive defects at the dentin margin were significantly higher than at the enamel margin with the application of the etch-and-rinse mode.

Nair P, Shetty H, D'Costa V, Jayaprakash K. Comparative evaluation of shear bond strength of a bioactive material to composite resin using three different universal bonding agents: An in vitro study

Background:

Calcium silicate-based cements or bioceramics have revolutionized and simplified pulp-capping procedures due to its versatility and accessibility.

Aim:

This study aimed to assess the shear bond strength (SBS) of a bioceramic material to composite resin at two aging periods and with three universal adhesives.

Materials and Methods:

Forty-eight samples of Biodentine with a height of 2 mm and internal diameter of 4 mm were prepared. After 12 min of mixing, 24 samples were randomly selected and divided into four subgroups: Group I: Single Bond Universal, Group II: Palfique Universal Bond, Group III: G-Premio BOND, and Group IV: Control. Composite resin was restored over Biodentine after the application of universal adhesives using a cylindrical plastic mold of 2 mm height and 2 mm internal diameter. This process was repeated 24 h after mixing on the remaining 24 samples of Biodentine. The universal testing machine was used to measure the SBS of the fractured specimens, followed by stereomicroscopic evaluation. One-way ANOVA test and Bonferroni post hoc test were used to statistically analyze the data.

Results:

Highest SBS values were observed in Group III at 12 min and 24 h of the setting of Biodentine.

Conclusions:

Compared to the 12-min group, SBS was higher at 24 h. Group III exhibited higher bond strength than other subgroups.

Do universal adhesives provide the benefits from double-application or an extra bonding layer in composite repair?

This study aimed to determine whether the application of extra hydrophobic resin (EHR) or double layer (DL) improves microtensile bond strength (μTBS) of two universal adhesives to composite resin. Composite blocks were fabricated and exposed to thermal cycles. The specimens were horizontally sectioned into two halves. Scotch Bond Universal (SBU) and Clearfil S3 Bond Universal (CSBU) were applied to the ground composite surface according to the manufacturers' instructions, or with DL application or EHR application. The repair composite was incrementally placed to bonded planes. Composite sticks were achieved and tensed with a universal testing machine, followed by examining the fracture surfaces by a scanning electron microscope. Data were evaluated by Weibull analysis (shape and scale [σ_θ and σ_0.10 ] parameters) using the maximum likelihood method. The σ_θ and σ_0.10 , respectively, estimate strength at 63.2 and 10% probability of failure. Shape parameter values showed significant differences among treatments. DL application of CSBU did not affect μTBS values at σ_θ of failure but caused to decrease μTBS values at σ_0.10 of failure. DL application of SBU reduced μTBS values at σ_θ of failure. DL or EHR coating did not improve μTBS of SBU. EHR application increased μTBS of CSBU, whereas DL application did not benefit.

Marginal quality of a full-body bulk-fill composite placed with an universal adhesive system in etch-and-rinse and self-etch mode: An in vitrostudy

Background

Marginal seal of a nanohybrid bulk-fill composite compared to a nanohybrid conventional composite, using a universal adhesive (UA) applied in etch-and-rinse (ER) and self-etch (SE) mode was investigated.

Material and Methods

Thirty-six intact molars were selected and two standardized cavities in each tooth were prepared and allocated into four groups according to restorative material and etching strategy. All samples were placed in a 1% methylene blue solution for 24 h, then cut in the middle of the restorations obtaining two parts (n=144) and used for microscopic evaluation (50x) for dye penetration measurements.

Results

The data were analysed by ANOVA and Tukey post-hoc test (p<0.05). Marginal seal was influenced by adhesive strategy (p<0.05) but not from the composite used (p>0.05).

Conclusions

Simplified restorations with nanohybrid bulk-fill composite showed comparable marginal leakage to incrementally placed nanohybrid composite. The UA used with a ER technique resulted in better marginal seal irrespective of the restorative material used.

Key words:Bulk-fill composite, universal adhesive, self-etching, etch-and-rinse, marginal seal.

Is clinical behavior of composite restorations placed in non-carious cervical lesions influenced by the application mode of universal adhesives? A systematic review and meta-analysis

OBJECTIVE

To answer the following PICOS question: "Is the risk of retention loss, marginal discoloration, marginal adaptation and postoperative sensitivity (POS) equal for etch-and-rinse (EAR) compared to self-etch (SE) or selective-enamel etch (SEE) mode when restoring non carious cervical lesions (NCCLs) with universal adhesives?".

METHODS

PubMed, Scopus, Web of Science, Cochrane Central Register of Controlled Trials, Scientific Electronic Library Online, LILACS, OpenGrey and Google Scholar™ were searched. Randomized controlled clinical trials in which resin composites and universal adhesives were used for restoration of NCCLs were considered. Cochrane Risk of Bias Tool was used to assess the risk of bias. Meta-analyses were performed using Revman; random-effects models were applied, and heterogeneity was tested using the I² index. The significance level was set at p < 0.05. Certainty of evidence was assessed by GRADE tool.

RESULTS

After screening, 20 articles were included in qualitative, while 14 articles were used for quantitative synthesis. Twelve studies ranked as "low", while 8 studies scored as "unclear" for risk of bias. At 12- and 18/24-months the risk for retention loss was higher for SE than for EAR groups (p = 0.005; RR = 0.22, 95% CI [0.08, 0.63],[moderate certainty of evidence and p = 0.0002; RR = 0.32, 95% CI [0.17, 0.58], moderate certainty of evidence, respectively). No significant differences were observed for marginal discoloration and adaptation (p > 0.05). The probability of POS occurrence was less in SE than in EAR groups (RR = 2.12, 95% CI [1.23, 3.64], moderate certainty of evidence). The certainty of evidence for other outcomes was scored as "low" or "moderate", depending on the follow-up period.

SIGNIFICANCE

Using universal adhesives in EAR or SEE mode provides more predictable retention, while SE strategy reduces the risk of POS occurrence.

Effect of Adhesive Application Method on the Enamel Bond Durability of a Two-Step Adhesive System Utilizing a Universal Adhesive-Derived Primer

This study aimed to evaluate the effect of the adhesive application method on the durability of the enamel bond and the thickness of the adhesive layer. A new-generation two-step universal adhesive system, G2-Bond Universal, and two conventional two-step adhesive systems were utilized. The shear bond strength to bovine enamel was measured after thermal cycling in both etch-and-rinse and self-etch modes. Fifteen specimens were divided into three groups as follows: Group I, wherein a strong air stream was applied over the bonding agent for 5 s; Group II, wherein a gentle air stream was applied over the bonding agent for 5 s; and Group III, which was prepared as in Group II, followed by the application of a second layer of the bonding agent and a gentle air stream for 5 s. The durability of the enamel bond and thickness of the tested adhesives were influenced by the application method in both etching modes. The application method used in Group II appeared to be most suitable in terms of the bonding of the adhesives to the enamel. The new-generation two-step self-etch adhesive, comprising a universal adhesive-derived primer and a hydrophobic bonding agent, showed superior bond performance to the conventional two-step adhesive systems.

Influence of two carbodiimides on the bond strength of universal adhesives to dentin

The pretreatment of dentin with cross-linking agents during bonding procedures has been proposed to improve the mechanical properties of the collagen in the hybrid layer and reduce the biodegradation of the adhesive interface. The aim of this study was to evaluate the influence of pretreatment with two carbodiimides on the dentin bond strength of universal adhesives, after thermocycling. Three universal adhesives in the self-etching mode were used (Single Bond Universal-SBU, Clearfil Universal-CLU and Ambar Universal-ABU). A self-etching adhesive system (Clearfil SE Bond-CSB) was used as control. Two carbodiimides, 1-ethyl-3-(3'-dimethylaminopropyl)-carbodiimide (EDC) and N,N'-dicyclohexylcarbodiimide (DCC), were applied for 1 min. The excess solution was removed with absorbent paper and the universal adhesives were applied. The specimens were stored for 24 h in distilled water at 37 °C or 10,000 thermal cycles (5-55 °C, 30 s) and then were prepared for microtensile bond strength test (n  =  4 teeth, average of 21 sticks per group). Data were analyzed using three-way ANOVA and Tukey's (α  =  5%). After 24 h, SBU and CSB had statistically similar bond strength values for the control groups (22.07  ±  9.03 and 19.82  ±  7.28 MPa), with EDC (30.21  ±  11.30 and 19.67  ±  5.36 MPa) and DCC (30.12  ±  13.43 and 19.82  ±  7.28 MPa) pretreatments (p  >  0.05). The use of EDC (32.57  ±  9.60 MPa) and DCC (24.71  ±  9.87 MPa) showed statistically higher bond strength for CLU than for the control group (14.62  ±  6.16 MPa; p  <  0.05). After thermocycling, the SBU, CLU, and CSB groups showed statistically similar bond strengths with the use of EDC (27.08  ±  8.44; 18.74  ±  5.41; and 24.55  ±  10.43 MPa) and without the use of cross linkers (20.06  ±  7.99; 22.55  ±  9.04; and 26.54  ±  10.13 MPa; p  >  0.05). Groups tested after 24 h in distilled water presented higher bond strength than those submitted to thermocycling. It can be concluded that the use of cross linkers influenced the immediate bond strength of the universal adhesives, and this was dependent on the combination of the adhesive system and type of carbodiimide. The use of EDC increased the immediate bond strength of CLU. DCC increased the bond strength of ABU at 24 h, but the values were lower than those of the control group after aging for three out of the four adhesives.

Update on Enamel Bonding Strategies

Optimal strategies for the application of an adhesive differ between enamel and dentin because of the differences in their composition. The development of adhesive systems has mainly focused on the bonding of dentin, rather than on the enamel, by etching with phosphoric acid (PA). Dental adhesive technologies continue to rapidly advance, and various adhesive systems have been developed since the study of Buonocore in 1955. He introduced the enamel acid-etch technique. Then, the etch-and-rinse (ER) system was developed, and subsequently, the self-etch (SE) system. Universal adhesives are a new generation of one-bottle SE adhesives that can be applied with either ER mode or SE mode, or a combined system involving selective enamel etching mode. Since the combination of PA etching and the SE system differs from conventional ER systems, the enamel bonding strategy should be carefully considered. This concise review of the literature on reliable enamel bonding strategies should prove helpful to clinicians to choose an appropriate adhesive system to achieve optimal clinical outcomes.

Bond Strength of Universal Adhesives to Dentin: A Systematic Review and Meta-Analysis

Currently, the availability of a wide variety of universal adhesives makes it difficult for clinicians to choose the correct system for specific bonding situations to dentin substrate. This study aimed to determine whether there are any alternative techniques or additional strategies available to enhance the bond strength of universal adhesives to dentin through a systematic review and meta-analysis. Two reviewers executed a literature search up to September 2020 in four electronic databases: PubMed, ISI Web of Science, Scopus, and EMBASE. Only in vitro studies that reported the dentin bond strength of universal adhesives using additional strategies were included. An analysis was carried out using Review Manager Software version 5.3.5 (The Nordic Cochrane Centre, The Cochrane Collaboration, Copenhagen, Denmark). The methodological quality of each in vitro study was assessed according to the parameters of a previous systematic. A total of 5671 potentially relevant studies were identified. After title and abstract examination, 74 studies remained in systematic review. From these, a total of 61 studies were included in the meta-analysis. The bond strength of universal adhesives to dentin was improved by the use of one of the following techniques: Previous application of matrix metalloproteinases (MMP) inhibitors (p < 0.001), prolonged application time (p = 0.007), scrubbing technique (p < 0.001), selective dentin etching (p < 0.001), non-atmospheric plasma (p = 0.01), ethanol-wet bonding (p < 0.01), prolonged blowing time (p = 0.02), multiple layer application (p = 0.005), prolonged curing time (p = 0.006), and hydrophobic layer coating (p < 0.001). On the other hand, the use of a shortened application time (p = 0.006), and dentin desensitizers (p = 0.01) impaired the bond strength of universal adhesives to dentin. Most of the analyses performed showed a high heterogenicity. The in vitro evidence suggests that the application of universal adhesives using some alternative techniques or additional strategies may be beneficial for improving their bonding performance to dentin. This research received no external funding. Considering that this systematic review was carried out only with in vitro studies, registration was not performed.

Effect of Different Application Techniques of Universal Bonding System on Microtensile Bond Strength of Bulk-Fill Composites to Primary and Permanent Dentin

Objectives

This study aimed to determine the microtensile bond strength (μTBS) of a bulk-fill composite to permanent and primary coronal dentin using a universal adhesive in self-etch and total-etch modes.

Materials and Methods

This in-vitro study was performed on 52 occlusal dentinal surfaces of human primary and permanent teeth. The crowns were cut to the gingival level. The 48 prepared dentin sections were randomly assigned to the following groups (n=13): A: Primary/Total-etch, B: Primary/Self-etch, C: Permanent/Total-etch, and D: Permanent/Self-etch. In groups A and C, after etching for 15 seconds, two layers of a universal bonding (Futurabond U) were applied and cured for 10 seconds. All samples were filled with a bulk-fill composite (x-trafil; VOCO) and cured for 40 seconds. The samples were cut to a bar-shaped dentin block with the dimensions of 1×1×1 mm³, and after 10,000 thermocycles, the μTBS test was accomplished at a crosshead speed of 1 mm/minute. The mean and standard deviation (SD) of μTBS were calculated, and the data were analyzed using two-way analysis of variance (ANOVA) and Fisher's exact test.

Results

The mean μTBS was as follows: A: 15.03±2.0279, B: 11.11±2.4423, C: 23.50±4.8165, and D: 16.26±6.3200 MPa. Futurabond U showed a higher μTBS in the total-etch mode (P<0.001). The permanent teeth had greater μTBS than the primary teeth (P<0.001). Similar percentages of failure modes were observed in the total-etch groups but in the self-etch groups, most failures were in the form of adhesive and mixed.

Conclusion

Greater μTBS was observed in the permanent teeth with the total-etch technique.

Significance of immediate dentin sealing and flowable resin coating reinforcement for unfilled/lightly filled adhesive systems

BACKGROUND

Immediate dentin sealing implies applying an adhesive system to dentin directly after tooth preparation, before impression. The technique is universal (inlays, onlays, veneers, crowns) and well documented clinically and experimentally. Different types of dentin bonding agents (DBAs) are available on the market. Major differences lie in the thickness of the hybrid layer and overlaying adhesive resin (filled vs. unfilled/lightly filled adhesives).

OBJECTIVE

The objective of this work is to provide precise clinical instructions and present new experimental data about the bond strength of five DBAs (Optibond FL, Scotchbond MP, Single Bond Plus, Clearfil SE Bond, and Scotchbond Universal) used conventionally (dentin sealed at the time of restoration delivery) or with immediate dentin sealing, as well as with an additional flowable resin coating.

METHODS

Seventy-five human molars were selected, restored/tested according the microtensile bond strength method. Fifteen groups (n=5) were obtained from the combination of the five DBAs and three application modes: delayed dentin sealing, immediate dentin sealing and immediate dentin sealing with flowable resin coating.

RESULTS

It appears that immediate dentin sealing was confirmed to significantly improve the bond strength of all tested adhesives. The use of a flowable resin coating reinforcement after immediate dentin sealing increased the microtensile bond strength of all unfilled/lightly filled adhesives (from 233% of increase for ScotchBond MP, up to 560% for Clearfil SE Bond) and maintained the performance of the 3-step golden standard adhesive. Optibond FL used with (52.51 MPa) or without (54.75 MPa) additional flowable resin coating and Clearfil SE Bond (45.64 MPa) used with flowable resin coating provided the best results.

CLINICAL SIGNIFICANCE

The original immediate dentin sealing (IDS) technique implies the use of a filled DBA. With unfilled/lightly filled adhesives, it is suggested to reinforce IDS with an additional flowable resin coating. This seems especially paramount to the performance of simplified adhesive systems to protect the thin bonding interface from oxygen inhibition and preserve IDS layer during predelivery cleaning of the preparation. The clinical reinforcement of unfilled/lightly filled IDS with flowable resin composite is encouraged for more predictable bonding.

Adhesive dentistry: Current concepts and clinical considerations

OBJECTIVES

To address contemporary concepts in adhesive dental materials with emphasis on the evidence behind their clinical use.

OVERVIEW

Adhesive dentistry has undergone major transformations within the last 20 years. New dental adhesives and composite resins have been launched with special focus on their user-friendliness by reducing the number of components and/or clinical steps. The latest examples are universal adhesives and universal composite resins. While clinicians prefer multipurpose materials with shorter application times, the simplification of clinical procedures does not always result in the best clinical outcomes. This review summarizes the current evidence on adhesive restorative materials with focus on universal adhesives and universal composite resins.

CONCLUSIONS

(a) Although the clinical behavior of universal adhesives has exceeded expectations, dentists still need to etch enamel to achieve durable restorations; (b) there is no clinical evidence to back some of the popular adjunct techniques used with dental adhesives, including glutaraldehyde-based desensitizers and matrix metalloproteinase inhibitors; and (c) the color adaptation potential of new universal composite resins has simplified their clinical application by combining multiple shades without using different translucencies of the same shade.

CLINICAL SIGNIFICANCE

New adhesive restorative materials are easier to use than their predecessors, while providing excellent clinical outcomes without compromising the esthetic quality of the restorations.

Current perspectives on dental adhesion: (1) Dentin adhesion - not there yet

The essential goal of any adhesive restoration is to achieve a tight and long-lasting adaptation of the restorative material to enamel and dentin. The key challenge for new dental adhesives is to be simultaneously effective on two dental substrates of conflicting nature. Some barriers must be overcome to accomplish this objective. While bonding to enamel by micromechanical interlocking of resin tags within the array of microporosities in acid-etched enamel can be reliably achieved and can effectively seal the restoration margins against leakage, bonding effectively and durably to organic and humid dentin is the most puzzling task in adhesive dentistry.

Much of the research and development of dental adhesives has focused on making the clinical procedure more user-friendly by reducing the number of bottles and/or steps. Although clinicians certainly prefer less complicated and more versatile adhesive materials, there is a trade-off between simplification of dental adhesives and clinical outcomes. Likewise, new materials are launched with claims of being novel and having special properties without much supporting evidence.

This review article discusses dental adhesion acknowledging pioneer work in the field, highlights the substrate as a major challenge to obtain durable adhesive restorations, as well as analyzes the three adhesion strategies and their shortcomings. It also reviews the potential of chemical/ionic dental adhesion, discusses the issue of extensively published laboratory research that does not translate to clinical relevance, and leaves a few thoughts in regard to recent research that may have implications for future adhesive materials.

Effect of air-blowing temperature and water storage time on the bond strength of five universal adhesive systems to dentin

The purpose of this study was to evaluate the air-blowing temperature and water storage time on the micro-tensile bond strength (μTBS) of five universal adhesive systems to dentin. The bond strength with two different air-blowing temperatures (60±2ºC and 23±2ºC) was measured after water storage at 37ºC for 24 h and 100 days respectively. The fracture surface on dentin side was observed by scanning electron microscope (SEM). Three-way ANOVA revealed a significant effect of universal system (p<0.001) and air-blowing temperature (p<0.001) on bond strength to dentin except water-storage time (p=0.145). The interaction within three factors was significantly different (p<0.001). It could be concluded that the μTBS of universal systems to dentin was material-depended. The higher and more stable bonding performance of universal systems on dentin could be achieved by air-blowing at 60±2ºC temperature. In addition, the quantity of voids in the adhesive layer of aceton-based universal adhesive was significantly reduced by higher temperature.

Influence of different phosphoric acids before application of universal adhesive on the dental enamel

BACKGROUND

There are different etching gels available, which have different composition, different pH, and different viscosity, and there is little information in the literature comparing all these products.

OBJECTIVE

To evaluate the mean microshear bond strength and morphological characteristics of tooth enamel by evaluating different phosphoric acids combined with a universal adhesive system.

MATERIALS AND METHODS

Eighty-four enamel samples were used, which were divided according to the acid conditioning: G1: Scotchbond Etchant (3M Oral Care), G2: Ultra-Etch (Ultradent), G3: Eco-Etch (IvoclarVivadent), G4: ETCH-37 with BAC (Bisco), G5: Etching gel (Densell), G6: Condac 37 (FGM), and G7: Scotchbond Universal Adhesive (3M Oral Care) in self-etch mode. For the adhesive procedure, Scotchbond Universal Adhesive was the one used as indicated the manufacturer's instructions, 0.9-mm-diameter resin cylinders were placed. The microshear bond strength test was performed after being stored for 24 hours in water. The morphological characteristics of tooth enamel were analyzed using the Raman confocal microscope alpha300RA. The analysis of variance (ANOVA) test and Tukey post-test were used to analyze the differences between the groups.

RESULTS

The mean microshear bond strength values obtained for groups 1, 4, 5 were significantly greater than groups 2, 3, 6 and 7 (p < .05). All groups presented demineralization after the application of the etching acid, and few signs of demineralization were evident in group 7.

CONCLUSIONS

Acid-etching with ETCH-37 with BAC, Etching gel, and Scotchbond Etchant improved the adhesive strength in the enamel using an universal adhesive, and acid-etching with Condac 37, Ultra-Etch, and Eco-Etch provides similar adhesive strength values to self-etch mode of universal adhesive.

CLINICAL SIGNIFICANCE

All acid etchants should be considered as different. The test confirms that enamel etching prior to the application of a universal adhesive system depends on the selected acid etchand product.

Zinc-Calcium-Fluoride Bioglass-Based Innovative Multifunctional Dental Adhesive with Thick Adhesive Resin Film Thickness

Apart from producing high bond strength to tooth enamel and dentin, a dental adhesive with biotherapeutic potential is clinically desirable, aiming to further improve tooth restoration longevity. In this laboratory study, an experimental two-step universal adhesive, referred to as Exp_2UA, applicable in both the etch-and-rinse (E&R) and self-etch (SE) modes and combining a primer, containing 10-methacryloyloxydecyldihydrogen phosphate as a functional monomer with chemical binding potential to hydroxyapatite, with a bioglass-containing hydrophobic adhesive resin, was multifactorially investigated. In addition to primary property assessment, including measurement of bond strength, water sorption, solubility, and polymerization efficiency, the resultant adhesive-dentin interface was characterized by transmission electron microscopy (TEM), the filler composition was analyzed by energy-dispersive X-ray spectroscopy, and the bioactive potential of the adhesive was estimated by measuring the long-term ion release and assessing its antienzymatic and antibacterial potential. Four representative commercial adhesives were used as reference/controls. Application in both the E&R and SE modes resulted in a durable bonding performance to dentin, as evidenced by favorable 1 year aged bond strength data and a tight interfacial ultrastructure that, as examined by TEM, remained ultramorphologically unaltered upon 1 year of water storage aging. TEM revealed a 20 μm thick hydrophobic adhesive layer with a homogeneous bioglass filler distribution. Adequate polymerization conversion resulted in extremely low water sorption and solubility. In situ zymography revealed reduced endogenous proteolytic activity, while Streptococcus mutans biofilm formation was inhibited. In conclusion, the three-/two-step E&R/SE Exp_2UA combines the high bonding potential and bond degradation resistance with long-term ion release, rendering the adhesive antienzymatic and antibacterial potential.

Influence of Acid Etching and Universal Adhesives on the Bond Strength to Dentin

Abstract The purpose of this study was to evaluate the influence of the application mode of three universal adhesive systems on interfacial physical properties of indirect composite restorations adhesively cemented to dentin cavities. Seventy-eight bovine lower incisors were selected and a slice of dentin (thickness: 2 mm) between the buccal surface and pulp chamber was obtained for each tooth. Conical cavities were made on this surface. The internal walls of the cavities were then coated with a hydrophilic gel, filled with composite resin and photopolymerized. The dentin/cone sets were divided into 6 groups (n=10) according to type of universal adhesive (TETRI: Tetric N Bond, FUT: Futura Bond U, SBU: Single Bond Universal) and acid etching on dentin (A: with acid etching; WA: without acid etching). The acid etching and the adhesive systems were applied to the surface of the dentin. All composite resin cones were sandblasted (Al2O3, 20 s) and silanized. After surface treatment, the cones were cemented (RelyX Ultimate) into the dentin cavity and photopolymerized. After thermocycling (10,000 cycles), samples were submitted to marginal adaptation analysis (using caries detector dye), push-out test (0.5 mm/min), and failure mode analysis. Additional samples were prepared for nanoleakage analysis (SEM). The data (MPa) were analyzed by two-way ANOVA and Tukey’s post-test (5%). The groups in which the dentin was acid etched showed significantly lower bond strength values in the push-out test (p<0.01). Dentin acid etching significantly reduced the bond strength between universal adhesive systems and dentin in indirect restorative procedures.

Effect of double-layer application on the early enamel bond strength of universal adhesives

OBJECTIVES

The present study aimed to investigate the changes in the enamel bond strengths of universal adhesives in the early phase of specimen creation and evaluate the effect of double-layer application on enamel bond effectiveness using different etching modes.

METHOD

Four universal adhesives, namely Clearfil Universal Bond Quick, G-Premio Bond, Scotchbond Universal, and Tokuyama Universal Bond, were used. Clearfil SE Bond two-step self-etch adhesive system was used as a comparison. Fifteen specimens per group were used for determining the shear bond strength (SBS) to bovine enamel in the etch-and-rinse or self-etch mode. The adhesive was applied to specimens in accordance with the manufacturers' instructions (single-layer application), or the adhesive was applied twice (double-layer application). The bonded specimens were stored in distilled water at 37 °C for 5 min or 1, 6, 12, or 24 h before SBS testing. The flexural properties of the resin composite Clearfil AP-X were measured for the same storage periods.

RESULTS

All universal adhesives exhibited increased SBS values with prolonged storage periods regardless of the application technique or etching mode used. Double-layer application was associated with higher SBS values than single-layer application for most universal adhesives over the same storage period.

CONCLUSION

Phosphoric acid pre-etching and double-layer application of universal adhesives resulted in increased enamel bond strength in the early phase of specimen bonding.

CLINICAL RELEVANCE

Care should be taken when using universal adhesives in the self-etch mode for enamel bonding because the enamel adhesion is sensitive to the duration after filling.

Quick bonding using a universal adhesive

OBJECTIVES

This study aimed to measure the microtensile bond strength (μTBS) of a new universal adhesive (UA) bonded to dentin following a quick bonding mode.

MATERIALS AND METHODS

The experimental UA 'SKB-100,' now commercialized as Clearfil Universal Bond Quick ('C-UBq'; Kuraray Noritake), was investigated, with Scotchbond Universal ('SBU'; 3M Oral Care) and the two-step self-etch (SE) adhesive Clearfil SE Bond 2 ('C-SE2'; Kuraray Noritake) serving as references. The adhesives were employed separately in etch&rinse (E&R) and SE modes on each tooth half following a split-tooth design and following their respective instructions for use, except for C-UBq that besides the manufacturer's instructed quick bonding mode was also applied and left untouched for 20 s prior to light curing ('C-UBq_20s') and for C-SE2 that was also applied in the E&R mode. μTBS of half of the specimens was measured upon 1 week (1w), with the other half tested after 6-month (6m) storage in distilled water at 37 °C. Data were statistically analyzed using linear mixed-effects modeling and three-way ANOVA (p < 0.05). The adhesive-dentin interfaces were ultrastructurally characterized by TEM.

RESULTS

C-UBq revealed a significantly lower μTBS than C-SE2. The highest μTBS was recorded for C-UBq_20s_1w and C-SE2_1w, both when applied in E&R mode. However, μTBS of C-UBq_20s significantly decreased upon aging in both modes. C-SE2 presented the significantly highest 'aged' μTBS.

CONCLUSION

C-UBq applied in the quick bonding mode did not underperform to the UAs applied for 20 s. Superior bonding effectiveness was achieved by C-SE2 in SE and E&R bonding modes.

CLINICAL RELEVANCE

Extended application time of C-UBq improved solely its immediate but not aged bonding effectiveness.

Comparison of dentin bond durability of a universal adhesive and two etch-and-rinse adhesive systems

OBJECTIVE

This study aimed to compare dentin bond durability under different degradation conditions between two etch-and-rinse (ER) systems and a universal adhesive in ER mode.

METHOD

This study used a universal adhesive [Scotchbond Universal (SU)], a three-step ER adhesive [Scotchbond Multi-Purpose Plus (SM)], and a two-step ER adhesive [Single Bond Plus (SB)]. A phosphoric acid-etching agent was applied to bovine dentin prior to the application of either a primer or the adhesive. After acid etching, bonding procedures were conducted. The specimens were divided into three group classes: (1) subjected to 10,000, 30,000, or 50,000 thermal cycles (TC); (2) stored in distilled water at 37 °C for 6 months or 1 year (WS); and (3) stored in distilled water for 24 h (baseline). Shear bond strength (SBS) tests were conducted.

RESULTS

SB showed a higher baseline SBS than the other adhesives. Defining the baseline SBS value for each adhesive system as 100%, TC groups ranged from 56.1 to 70.3% for SM, from 98.4 to 103.7% for SB, and from 120.3 to 126.7% for SU. WS groups ranged from 66.2 to 71.4% for SM, from 98.1 to 103.3% for SB, and from 102.5 to 118.1% for SU.

CONCLUSIONS

Although SB showed relatively stable dentin bond performance under all degradation conditions, SM showed decreased dentin SBS with prolonged degradation. SU did not show any significant decrease in SBS from the baseline under any degradation condition.

CLINICAL RELEVANCE

The universal adhesive showed comparable adhesive performance with the two-step ER adhesive.

Zinc oxide and copper nanoparticles addition in universal adhesive systems improve interface stability on caries-affected dentin

This study evaluated the MMP inhibition of the zinc oxide and copper nanoparticles (ZnO/CuNp), and the effects of their addition into adhesives on antimicrobial activity (AMA), ultimate tensile strength (UTS), in vitro degree of conversion (in vitro-DC), as well as, resin-dentin bond strength (μTBS), nanoleakage (NL) and in situ-DC on caries-affected dentin. Anti-MMP activity was evaluated for several MMPs. ZnO/CuNp (0% [control]; 5/0.1 and 5/0.2 wt%) were added into Prime&Bond Active (PBA) and Ambar Universal (AMB). The AMA was evaluated against Streptococcus mutans. UTS were tested after 24 h and 28d. After induced caries, adhesives and composite were applied to flat dentin surfaces, and specimens were sectioned to obtain resin-dentin sticks. μTBS, NL, in vitro-DC and in situ-DC were evaluated after 24 h. ANOVA and Tukey's test were applied (α = 0.05). ZnO/CuNp demonstrated anti-MMP activity (p < 0.05). The addition of ZnO/CuNp increased AMA and UTS (AMB; p < 0.05). UTS for PBA, in vitro-DC, in situ-DC and μTBS for both adhesives were maintained with ZnO/CuNp (p > 0.05). However, lower NL was observed for ZnO/CuNp groups (p < 0.05). The addition of ZnO/CuNp in adhesives may be an alternative to provide antimicrobial, anti-MMP activities and improves the integrity of the hybrid layer on caries-affected dentin.

Effect of a hydrophobic bonding resin on the 36-month performance of a universal adhesive-a randomized clinical trial

OBJECTIVES

To evaluate if the addition of a layer of a hydrophobic bonding resin to the recommended application sequence of a universal adhesive improves the respective clinical behavior in non-carious cervical lesions (NCCLs) after 36 months.

MATERIALS AND METHODS

Scotchbond Universal Adhesive (SBU, 3M Oral Care) was applied in NCCLs of 39 subjects using four adhesion strategies: (1) three-step ER (etch-and-rinse), (2) two-step ER, (3) two-step SE (self-etch), and (4) one-step SE. An extra layer of a hydrophobic bonding resin was applied for strategies three-step ER and two-step SE. The same composite resin (Filtek Supreme XTE, 3M Oral Care) was used for all strategies. Restorations were evaluated at baseline and 18 and 36 months using the modified United States Public Health Service (USPHS) criteria. Kruskal-Wallis, Mann-Whitney U, Friedman, and Wilcoxon non-parametric tests were computed.

RESULTS

The cumulative failure rate was 8.6%. The 36-month retention rates were 100% for both 3-ER and 2-ER, 76.0% for 2-SE, and 86.2% for 1-SE. A lower retention rate was observed for two-step SE at 36 months compared with both three-ER (p < 0.01) and two-ER (p < 0.01). Identical retention rates were measured for the two SE groups. When retention rate was compared at baseline versus 36 months for each adhesion strategy, a significant decrease was observed for 2-SE. The restorations performed with 3-ER, 2-SE, and 1-SE had a significant deterioration in marginal discoloration at the 18-month recall.

CONCLUSIONS

The 36-month clinical performance of Scotchbond Universal Adhesive improved for both etch-and-rinse strategies.

CLINICAL RELEVANCE

Phosphoric acid etching is still recommended to provide retention to composite restorations in NCCLs.

Universal dental adhesives: Current status, laboratory testing, and clinical performance

Increasing demand for simplified and user-friendly adhesive systems has led to the development of a new class of adhesives termed as Universal Adhesives (UAs). The term "Universal" reflects manufacturers' claims that these adhesives can be applied with any adhesion strategy and offer the versatility of use with a variety of direct and indirect restorative materials. The aim of this review was to synthesize the literature regarding the current status of UAs, their adhesion potential to various substrates and their performance in different restorative situations. In vitro studies, clinical trials and systematic reviews were identified utilizing controlled vocabulary and keyword searches in Medline and EMBASE databases. About 282 studies (272 in vitro studies; 11 clinical studies) were included. Available laboratory and clinical evidence does not support the claim that UAs can be used with any adhesive strategy. Although, they can chemically bond to various tooth and direct/indirect restorative substrates, the stability of this bond is material-dependent and subject to hydrolytic degradation. Hence, additional measures are still needed to ensure long-term durability. which undermines the versatility of UAs. The lack of long-term data regarding the clinical performance of UAs further complicates clinical decision-making. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 2121-2131, 2019.

Do universal adhesives promote bonding to dentin? A systematic review and meta-analysis

Objectives

The aims of this study were to conduct a systematic review of the microtensile bond strength (µTBS) of multi-mode adhesives to dentin and to perform a meta-analysis to assess the significance of differences in the µTBS of one of the most commonly used universal adhesives (Scotchbond Universal, 3M ESPE) depending on whether the etch-and-rinse or self-etch mode was used.

Materials and Methods

An electronic search was performed of MEDLINE/PubMed, ScienceDirect, and EBSCOhost. Laboratory studies that evaluated the µTBS of multi-mode adhesives to dentin using either the etch-and-rinse or self-etch mode were selected. A meta-analysis was conducted of the reviewed studies to quantify the differences in the µTBS of Scotchbond Universal adhesive.

Results

Only 10 studies fulfilled the inclusion criteria for the systematic review. Extensive variation was found in the restorative materials, testing methodologies, and failure mode in the reviewed articles. Furthermore, variation was also observed in the dimensions of the microtensile testing beams. The meta-analysis showed no statistically significant difference between the etch-and-rinse and self-etch modes for Scotchbond Universal adhesive (p > 0.05).

Conclusions

Multi-mode ‘universal’ adhesives can achieve substantial bonding to dentin, regardless of the used modes (either etch-and-rinse or self-etch).

One-year clinical evaluation of bulk-fill flowable vs. regular nanofilled composite in non-carious cervical lesions

OBJECTIVE

The aim of this double-blind, randomized trial was to evaluate the 1-year clinical performance of a bulk-fill flowable and a regular nanofilled composite in non-carious cervical lesions (NCCLs).

METHODS

Twenty-two subjects with at least two NCCLs were enrolled in the study. A total of 89 restorations were performed by a single operator using Filtek Supreme (FS) Ultra Universal or Filtek Bulk (FB) Fill Flowable. A universal adhesive (Scotchbond™ Universal Adhesive) was used with a self-etching approach in dentin. The restorations were evaluated by two independent and previously calibrated examiners at baseline (7 days), 6 months and 1 year, according to the USPHS modified criteria. Mann-Whitney U test was used to analyze the differences between composites and Wilcoxon signed rank test for comparisons between the baseline and follow-ups (α = 5%).

RESULTS

One restoration was considered clinically unacceptable due to loss of retention after 6 months in the FS group. FS presented statistically high scores for surface roughness when compared to FB after 1 year (p < 0.05), but both were considered clinically acceptable. After 1 year, the frequency of clinically unacceptable rates was 3.3% for anatomical form in the FB group, 1.1% for retention in the FS group, and 2.2% for marginal adaptation in both groups. All restorations, in both groups, presented score 0 over the 1-year period for marginal staining, postoperative sensitivity, and secondary caries.

CONCLUSION

Both composite resins showed acceptable clinical performances for the restoration of NCCLs after 1 year.

CLINICAL RELEVANCE

Both bulk-fill flowable and regular nanofilled composites showed good clinical performances for the restoration of NCCLs after 1 year.

Effects of different etching modes on the nanoleakage of universal adhesives: A systematic review and meta-analysis

PURPOSE

The aim of this systematic review was to evaluate how etching modes affect the nanoleakage of universal adhesive from in vitro studies.

MATERIALS AND METHODS

PubMed/MEDLINE, Web of Science, Scopus and Science Direct electronic databases were searched for in vitro studies that evaluated the nanoleakage of universal adhesives. A total of 511 (after duplicate removal) potentially relevant records were identified in the literature search. The titles and abstracts of the retrieved studies were screened by two independent researchers according to the main concept. Subsequently, the full text of potentially relevant studies was screened using the exclusion criteria. Thirteen studies were subjected to qualitative analysis, and 5 of them were selected for a detailed meta-analysis.

RESULTS

Seven universal adhesives were evaluated in this review. The meta-analysis demonstrated that the etch-and-rinse technique significantly reduced the nanoleakage of the Peak Universal and G-Bond Plus adhesives, whereas the self-etch mode reduced the nanoleakage of All-Bond Universal. In comparison, the etching technique did not significantly alter the nanoleakage of either Prime&Bond Elect or Scotchbond Universal which was characterized by the smallest nanoleakage.

CONCLUSIONS

Etching modes significantly, in various ways, influence the nanoleakage of universal adhesives.

CLINICAL SIGNIFICANCE

Contrary to the drive to simplify bonding technologies, an appreciation of their adhesive components and how these perform according to bonding technique could yield a knowledge-based practical approach that ultimately improves the longevity of direct composite restorations.

Effect of caries-affected dentin on one-step universal and multi-step etch-and-rinse adhesives’ bond strength

Abstract Objective To evaluate the influence of caries-affected dentin on bond strength of a universal one-step and a multi-step etch-and-rinse adhesive system. Material and method Enamel of 60 third human molars with and without caries was removed to expose dentin. The teeth were randomly assigned to six groups: Single Bond Universal (3M ESPE, St. Paul, MN, USA) in etch-and-rinse and in self-etch mode and Prime & Bond NT (Dentsply Co, Konstanz, Germany), all on sound and caries-affected dentin. Smear layer of the 30 sound dentin specimens was standardized by polishing with 600-grit SiC paper under water cooling. Residual infected dentin of the 30 caries-affected specimens was removed with a number 4 CA carbide bur until no caries smooth tissue was detectable by tactile-visual inspection. Cylinders of a light cured composite resin (Filtek Z350 XT, 3M ESPE) were built up using starch tubes and microshear test was performed until failure. The data was analyzed by one-way ANOVA and Tukey’s post hoc test. Result Significant differences in microshear bond strength (μSBS) were observed for the caries-affected groups, but not for sound dentin. The μSBS of Single Bond Universal were not influenced by the application protocol on sound dentin, however they were lower in the caries-affected group with both application protocols. The μSBS for Prime & Bond NT was not influenced by the dentin conditions. Conclusion Caries-affected dentin decrease in bond strength of Single Bond Universal in comparison to sound dentin. The bond strength of Prime & Bond NT was not altered by substrate conditions.

Recent Advances in Adhesive Bonding - The Role of Biomolecules, Nanocompounds, and Bonding Strategies in Enhancing Resin Bonding to Dental Substrates

PURPOSE OF REVIEW

To present an overview on the main agents (i.e., biomolecules and nanocompounds) and/or strategies currently available to amplify or stabilize resin-dentin bonding.

RECENT FINDINGS

According to studies retrieved for full text reading (2014-2017), there are currently six major strategies available to overcome resin-dentin bond degradation: (i) use of collagen crosslinking agents, which may form stable covalent bonds with collagen fibrils, thus strengthening the hybrid layer; (ii) use of antioxidants, which may allow further polymerization reactions over time; (iii) use of protease inhibitors, which may inhibit or inactivate metalloproteinases; (iv) modification of the bonding procedure, which may be performed by using the ethanol wet-bonding technique or by applying an additional adhesive (hydrophobic) coating, thereby strengthening the hybrid layer; (v) laser treatment of the substrate prior to bonding, which may cause specific topographic changes in the surface of dental substrates, increasing bonding efficacy; and (vi) reinforcement of the resin matrix with inorganic fillers and/or remineralizing agents, which may positively enhance physico-mechanical properties of the hybrid layer.

SUMMARY

With the present review, we contributed to the better understanding of adhesion concepts and mechanisms of resin-dentin bond degradation, showing the current prospects available to solve that problematic. Also, adhesively-bonded restorations may be benefited by the use of some biomolecules, nanocompounds or alternative bonding strategies in order to minimize bond strength degradation.

Universal cements: dual activated and chemically activated

Objective: The aim of the present study was to assess the bond strength of universal cements cured either dually or chemically only.

Methods: Three cements were assessed using different types of application: dual activated (DA) or chemically activated (CA). In total 80 dentin blocks were used, obtained through the enamel wear of the lingual and buccal surfaces of bovine incisors. Standard cone-shaped cavity preparations were created using diamond burs. Subsequently, indirect restoration blocks were designed with Filtek Z350 (3M ESPE) composite resin. The teeth were divided into two groups (DA and CA) and then subdivided into four subgroups (n = 10) prior to cementation with the respective products: Duo-Link (Bisco); RelyX Ultimate (3M ESPE); Nexus 3 (Kerr) and conventional RelyX ARC (3M ESPE) as the control. The cementation in the PA group was applied following the manufacturer’s instructions. The CA group was cemented in a darkroom to avoid exposure to light. They were stored in distilled water at 37 °C for 24 h and submitted to the push-out test. Data were analyzed by two-way ANOVA and Tukey’s post-hoc test (p < .05).

Results: The greatest bond strength results were obtained for photoactivated universal cements.

Conclusion: Chemical activation is not sufficient to ensure acceptable bond strength.

The role of copper nanoparticles in an etch-and-rinse adhesive on antimicrobial activity, mechanical properties and the durability of resin-dentine interfaces

OBJECTIVES

To evaluate the effect of addition of copper nanoparticles at different concentrations into an etch-and-rinse adhesive (ER) on antimicrobial activity, Knoop microhardness (KHN), in vitro and in situ degree of conversion (DC), as well as the immediate (IM) and 2-year (2Y) resin-dentine bond strength (μTBS) and nanoleakage (NL).

METHODS

Seven experimental ER adhesives were formulated according to the amount of copper nanoparticles incorporated into the adhesives (0 [control], 0.0075 to 1wt.%). We tested the antimicrobial activity of adhesives against Streptococcus mutans using agar diffusion assay after IM and 2Y. The Knoop microhardness and in vitro DC were tested after IM and 2Y. The adhesives were applied to flat occlusal dentine surfaces after acid etching. After resin build-ups, specimens were longitudinally sectioned to obtain beam-like resin-dentine specimens (0.8mm²), which were used for evaluation of μTBS and nanoleakage at the IM and 2Y periods. In situ DC was evaluated at the IM period in these beam-like specimens. Data were submitted to appropriate statistical analyses (α=0.05).

RESULTS

The addition of copper nanoparticles provided antimicrobial activity to the adhesives only in the IM evaluation and slightly reduced the KHN, the in vitro and in situ DC (copper concentrations of 1wt.%). However, KHN increase for all concentrations after 2Y. After 2Y, no significant reductions of μTBS (0.06 to 1% wt.%) and increases of nanoleakage were observed for copper containing adhesives compared to the control group.

CONCLUSION

Copper nanoparticles addition up to 0.5wt.% may provide antimicrobial properties to ER adhesives and prevent the degradation of the adhesive interface, without reducing the mechanical properties of the formulations.