Biomechanics, Bioactive and Biomimetic philosophy in restorative dentistry ̶ Quo vadis?

INTRODUCTION

In recent years, restorative dentistry has embraced various techniques, including direct, semi-direct, and indirect restorations, to address the replacement of lost tooth tissue. The focus has been on integrating the principles of Biomechanics, Bioactivity, and Biomimicry (3-Bio) as key drivers behind these innovations.

METHODS

The aim of this article is to provide a concise overview of three important aspects of restorative dental materials: biomechanics, bioactivity and biomimetics. Further, the aim is to provide readers with relevant information on the 3-Bio concept, offering insights in to the innovative approaches shaping modern restorative dentistry.

RESULTS

Developing restorative materials with interactive properties aligned with the 3-Bio concept poses a significant challenge. Currently, dentistry lacks a comprehensive system in this regard. The development of dental materials based on the 3-Bio concept could potentially elicit positive mechanical and biological responses in targeted tooth tissues.

CONCLUSION

Assessing several parameters through a battery of in vitro and in silico assays could help in tailoring the different aspects of the 3-Bio concept, spanning from bioactivity to biomimetics via biomechanics. This approach could allow the prediction and translation of the clinical performance of the assessed restorative materials.

CLINICAL SIGNIFICANCE

The findings of this opinion article highlight that the development of restorative materials aligned with the 3-Bio concept could enhance the management of dental defects and extend the longevity of bonded restorations, thereby improving patient care through tissue preservation. More collective efforts between clinicians, researchers, and even industrial partners are required to fully understand the correlation between bioactive behavior, biomechanical limitations, and biomimetics to provide suitable restorative materials for specific clinical applications.

Biomechanical Assessment of Endodontically Treated Molars Restored by Endocrowns Made from Different CAD/CAM Materials

The aim of this study was to evaluate the deflection and stress distribution in endodontically treated molars restored by endocrowns from different materials available for the computer-aided design/computer-aided manufacturing (CAD/CAM) technique using three-dimensional finite element analysis. The models represented extensively damaged molars restored by endocrowns from the following materials: translucent zirconia; zirconia-reinforced glass ceramic; lithium disilicate glass ceramic; polymer-infiltrated ceramic network (PICN) and resin nanoceramic. Axial and oblique loadings were applied and the resulting stress distribution and deflection were analyzed. The Mohr-Coulomb (MC) ratio was also calculated in all models. The translucent zirconia endocrown showed the highest stress concentration within it and the least stress in dental structures. The resin nanoceramic model was associated with the greatest stress concentration in dental tissues, followed by the PICN model. Stress was also concentrated in the distal region of the cement layer. The MC ratio in the cement was higher than 1 in the resin nanoceramic model. Oblique loading caused higher stresses in all components and greater displacement than axial loading, whatever the material of the endocrown was. The translucent zirconia model recorded deflections of enamel and dentin (38.4 µm and 35.7 µm, respectively), while resin nanoceramic showed the highest stress concentration and displacement in the tooth-endocrown complex.

Influence of the Peek Abutments on Mechanical Behavior of the Internal Connections Single Implant

The present study aimed to evaluate the biomechanical behavior of PEEK abutments with different heights on single titanium implants. To investigate the implant surface, different tests (scanning electron microscopy, energy-dispersive X-ray, and X-ray diffraction) were adopted. Herein, 20 implants received the 4.5 × 4.0 mm PEEK short abutment (SA) and 20 received the 4.5 × 5.5 mm PEEK long abutment (LA). The abutments were installed using dual-cure resin cement. To determine the fatigue test, two specimens from each group were submitted to the single load fracture test. For this, the samples were submitted to a compressive load of (0.5 mm/min; 30°) in a universal testing machine. For the fatigue test, the samples received 2,000,000 cycles (2 Hz; 30°). The number of cycles and the load test was analyzed by the reliability software SPSS statistics using Kaplan-Meier and Mantel-Cox tests (log-rank) (p < 0.05). The maximum load showed no statistically significant differences (p = 0.189) for the SA group (64.1 kgf) and the LA group (56.5 kgf). The study groups were statistically different regarding the number of cycles (p = 0.022) and fracture strength (p = 0.001). PEEK abutments can be indicated with caution for implant-supported rehabilitation and may be suitable as temporary rehabilitation.

Failure probability and stress distribution of milled porcelain-zirconia crowns with bioinspired/traditional design and graded interface

OBJECTIVE

To evaluate the failure probability and stress distribution of traditional and bioinspired porcelain-zirconia milled crowns, with and without silica infiltration (graded zirconia).

METHODS

Traditional crown design had a zirconia infrastructure veneered with porcelain; Bioinspired, had a porcelain infrastructure with translucent-zirconia veneer; Graded and Graded Bioinspired crowns had their zirconia layer infiltrated by silica (n = 25). The cameo surface of each crown (porcelain or zirconia) was glazed. The restoration layers were fused by a vitreous connector and the crowns were adhesively cemented to dies. The specimens were then mechanically cycled in a sliding machine using 100 N load at 4 Hz. The specimens were tested until 2 × 10⁶ cycles, and every 0.5 × 10⁶ cycles the crowns were evaluated under stereomicroscopy for the presence of failures. The stress distribution was inspected with Finite Element Analyses.

RESULTS

The predominant failure modes for the Traditional and Graded crowns were delamination and cracking, respectively. The Weibull parameters beta and eta were, respectively: Traditional 1.30 and 2.3 × 10⁶ cycles, and Graded 1.95 and 2.3 × 10⁶ cycles. Thus, the Traditional and Graded crowns presented greater susceptibility to failure due to fatigue, while the Bioinspired and Graded Bioinspired crowns showed no fatigue effect using 100N load, showing beta = 1 and eta of approximately 17 × 10⁶ cycles. Also, through finite element analyses, it was verified that the Bioinspired and Graded Bioinspired crowns presented the best stress distribution on both crowns and dental structures.

SIGNIFICANCE

Bioinspired and Graded Bioinspired crowns had the lowest failure probability and better stress distribution and may be considered robust long lasting restorations.

Effect of volumetric shrinkage of restorative materials on tooth structure: A finite element analysis

Post-treatment coronal hermetic seal of the root canal opening prevents the food or saliva which assist to achieve successful endodontic treatment. Gutta-percha is filled in the inner canal, that is, from cervical third to apical third. Gutta-percha does not provide the hermetic seal because it does not bound with dentine walls. Various new restorative materials have been developed in the last 6-7 decade but drawback related to the polymerization shrinkage of the composite resin remains a clinical problem. In general, dental composites having volumetric shrinkage of the material depends on its formulation and curing conditions. In this article, the effect of this polymerization shrinkage on the tooth structure has been studied.

Survival Probability, Weibull Characteristics, Stress Distribution, and Fractographic Analysis of Polymer-Infiltrated Ceramic Network Restorations Cemented on a Chairside Titanium Base: An In Vitro and In Silico Study

Different techniques are available to manufacture polymer-infiltrated ceramic restorations cemented on a chairside titanium base. To compare the influence of these techniques in the mechanical response, 75 implant-supported crowns were divided in three groups: CME (crown cemented on a mesostructure), a two-piece prosthetic solution consisting of a crown and hybrid abutment; MC (monolithic crown), a one-piece prosthetic solution consisting of a crown; and MP (monolithic crown with perforation), a one-piece prosthetic solution consisting of a crown with a screw access hole. All specimens were stepwise fatigued (50 N in each 20,000 cycles until 1200 N and 350,000 cycles). The failed crowns were inspected under scanning electron microscopy. The finite element method was applied to analyze mechanical behavior under 300 N axial load. Log-Rank (p = 0.17) and Wilcoxon (p = 0.11) tests revealed similar survival probability at 300 and 900 N. Higher stress concentration was observed in the crowns’ emergence profiles. The MP and CME techniques showed similar survival and can be applied to manufacture an implant-supported crown. In all groups, the stress concentration associated with fractographic analysis suggests that the region of the emergence profile should always be evaluated due to the high prevalence of failures in this area.

Influence of cavosurface angle on the stress concentration and gaps formation in class V resin composite restorations

The study aimed to evaluate the influence of cavosurface angle on stress concentration and gap formation in class V restorations. Cylindrical cavities 3 mm in diameter were prepared in forty-five bovine incisors, changing only the angle of the bur in relation to the flat surface of the tooth. The cavities maintained the same volume (17.67 mm³). The samples were divided according to the cavosurface angle, into three groups (n = 15): 90°, 120°, 135°. After adhesive application (Futurabond U, VOCO), the cavity was filled with bulk placement of a resin composite (GrandioSO, VOCO). The teeth were analyzed with stereomicroscopy. Data of marginal gap formation were statistically analyzed with a one-way analysis of variance (ANOVA) followed by Tukey tests (significance level: α = 0.05). Finite element analysis (FEA) was used to study residual stress in these geometries and to correlate those stresses with experimentally measured gap formation. The elastic modulus and polymerization shrinkage were determined for FEA. Residual shrinkage stresses were expressed in maximum principal stress (MPS). There was a significant difference in the gap formation among the groups (p = 0.001). A significantly lower marginal gap formation was found for 120° and 135° angles, with no significant difference between them. The cavosurface angle at 90° caused substantially higher stresses, in the restoration interface, with greater marginal gap. For the 120° and 135° angles, the stress concentrations were smaller and were located in the dental structure. The cavosurface angle influenced the marginal gap formation and stress concentration.

Influence of thickness and incisal extension of indirect veneers on the biomechanical behavior of maxillary canine teeth

Objectives

To analyze the influence of thickness and incisal extension of indirect veneers on the stress and strain generated in maxillary canine teeth.

Materials and Methods

A 3-dimensional maxillary canine model was validated with an in vitro strain gauge and exported to computer-assisted engineering software. Materials were considered homogeneous, isotropic, and elastic. Each canine tooth was then subjected to a 0.3 and 0.8 mm reduction on the facial surface, in preparations with and without incisal covering, and restored with a lithium disilicate veneer. A 50 N load was applied at 45° to the long axis of the tooth, on the incisal third of the palatal surface of the crown.

Results

The results showed a mean of 218.16 µstrain of stress in the in vitro experiment, and 210.63 µstrain in finite element analysis (FEA). The stress concentration on prepared teeth was higher at the palatal root surface, with a mean value of 11.02 MPa and varying less than 3% between the preparation designs. The veneers concentrated higher stresses at the incisal third of the facial surface, with a mean of 3.88 MPa and a 40% increase in less-thick veneers. The incisal cover generated a new stress concentration area, with values over 48.18 MPa.

Conclusions

The mathematical model for a maxillary canine tooth was validated using FEA. The thickness (0.3 or 0.8 mm) and the incisal covering showed no difference for the tooth structure. However, the incisal covering was harmful for the veneer, of which the greatest thickness was beneficial.

The importance of correct implants positioning and masticatory load direction on a fixed prosthesis

Background

Through the biomechanical study of dental implants, it is possible to understand the dissipation effects of masticatory loads in different situations and prevent the longevity of osseointegration. Aims: To evaluate the microstrains generated around external hexagon implants, using axial and non-axial loads in a fixed four-element prosthesis with straight implants and implants inclined at 17°.

Material and Methods

Three implants were modeled using CAD software following the manufacturer’s measurements. Then, implants were duplicated and divided into two groups: one with straight implants and respective abutments, and the other with angled implants at 17° and respective abutments. Both groups were arranged inside a block simulating bone tissue. A simplified fixed prosthesis was installed on both groups and the geometries were exported to CAE software. Five loads of 300N were performed at axial and non-axial points on the fixed prosthesis. Stress on the implants and strain on the block were both analyzed. An in vitro experiment was performed following all structures made in FEA in order to validate the model. In each experimental block, 4 strain gauges were linearly placed between the implants and the same loads were repeated with a loading applicator device.

Results

The deformations computed by the gauges were correlated with the FEA results, showing that the group with inclined implants had more damaging biomechanical behavior and was significantly different from the group with straight implants (P<0.005).

Conclusions

The mathematical model used is valid and inclined implants can induce unwanted bone remodeling.

Key words:Finite Element Analysis, Dental Implants, Fixed Prosthesis.

Finite element analysis on tooth and periodontal stress under simulated occlusal loads

The tooth stress elicited by occluding contact represents critical biomechanical information about dental health during chewing. Effects of occlusal contact on tooth stress remain obscure. In this study, a mandibular first molar finite element model was built from CT images. The effects of area size, location and direction of occlusal loading on both tooth and periodontal stresses were analysed. Results showed tooth and periodontal stress had drastically different patterns. Tooth stress value was much higher than periodontal stress value under the same task. Tooth stress concentration area and its value decreased from outside to inside. The Maximum Tooth Stress (MTS) always occurred at the loading site and a larger loading area elicited a smaller MTS value. The variation of MTS was larger when the fossa bottoms were inclined loaded than when the cusp tips were inclined loaded, larger when lingually loaded than when buccally loaded and larger when mesially loaded than when distally loaded. Distal loadings generally induced smaller Maximum Periodontal Stress (MPS) variations than the mesial loadings. These findings indicated exposure of the rational site(s) to occlusal contact should be helpful to achieve proper tooth and periodontal stress, thus to diminish loading associated structure problems.

Comparative three-dimensional finite element analysis of implant-supported fixed complete arch mandibular prostheses in two materials

Background:

The increase of requests for implant-supported prosthesis (ISP) with zirconia as infrastructure has attracted a lot of attention due to its esthetics, biocompatibility, and survival rate similar to metallic infrastructure. The aim of this study was to evaluate the influence of two different framework materials on stress distribution over a bone tissue-simulating material.

Materials and Methods:

Two ISP were modeled and divided into two infrastructure materials: titanium (Ti) and zirconia. Then, these bars were attached to a modeled jaw with polyurethane properties to simulate bone tissue. An axial load of 200 N was applied on a standardized area for both systems. Maximum principal stress (MPS) on solids and microstrain (MS) generated through the jaw were analyzed by finite element analysis.

Results:

According to MS, both models showed strains on peri-implant region of the penultimate (same side of the load application) and central implants. For MPS, more stress concentration was slightly higher in the left posterior region for Ti's bar. In prosthetic fixation screws, the MPS prevailed strongly in Ti protocol, while for zirconia's bar, the cervical of the penultimate implant was the one that highlighted larger areas of possible damages.

Conclusions:

The stress generated in all constituents of the system was not significantly influenced by the framework's material. This allows suggesting that in cases without components, the use of a framework in zirconia has biomechanical behavior similar to that of a Ti bar.