The Effect of Phosphoric Acid Pre-etching Times on Bonding Performance and Surface Free Energy with Single-step Self-etch Adhesives

Brief Narrative Review on Commercial Dental Sealants-Comparison with Respect to Their Composition and Potential Modifications

The scope of this paper is to compare different dental sealants and flow materials indicated for sealing pits and fissures considering their chemical formula. The narrative review aims to address the following questions: What is the essence of different dental sealants' activity, how does their chemical formula affect their mechanisms of caries prevention, and what makes a dental sealant efficient mean of caries prevention? Another vital issue is whether the sealants that contain fluoride, or any other additions, have potentially increased antimicrobial properties. An electronic search of the PubMed, Cochrane, Web of Science, and Scopus databases was performed. The following keywords were used: (dental sealants) AND (chemical composition). Additionally, information about composition and indications for clinical use provided by manufacturers were utilized. All of the considered materials are indicated for use both in permanent and primary dentition for sealing fissures, pits, and foramina caeca. The selection of suitable material should be made individually and adjusted to conditions of the sealing procedure and patient's needs. Cariostatic mechanisms increasing sealants' effectiveness such as fluoride release are desired in modern dentistry appreciating preventive approach. The review aims are to find crucial elements of sealants' composition which affect their cariostatic mechanisms.

One-Step Surface-Treatment Reagent (35% 3-O-Ethyl-l-ascorbic Acid Plus 50% Citric Acid Solution) Restores the Shear Bond Strength of Metal Brackets Bonded to Bleached Human Enamel: An In Vitro Study

This study investigates how a new substance, composed of ethyl ascorbic acid and citric acid, affects the shear bond strength (SBS) of metal brackets when bonded to bleached teeth. Forty maxillary premolar teeth were used and randomly placed into four groups (n = 10): the control group did not undergo bleaching; the remaining groups underwent bleached using 35% hydrogen peroxide. In group A, 37% phosphoric acid was applied after bleaching. In group B, 10% sodium ascorbate was used for ten minutes before 37% phosphoric acid. In group C, 35%3-O-ethyl-l-ascorbic acid plus 50% citric acid solution (35EA/50CA) was applied for 5 min. The subgroups were bonded immediately after bleaching. The SBS was determined with a universal testing machine and analyzed using one-way ANOVA and then Tukey's HSD tests. Adhesive remnant index (ARI) scores were determined with a stereomicroscope and analyzed with a chi-squared test. The significance level was 0.05. Group C demonstrated significantly higher SBS values than group A (p < 0.001), but was not significantly different than the control group or group C (p > 0.05). The ARI scores were significantly different among the groups (p < 0.001). In conclusion, enamel surface treatment using 35EA/50CA improved the reduced SBS to an acceptable clinical level and reduced the clinical chair time.

Effect of Different Etching Times on Pit-and-Fissure Sealant Micro-Shear Bond Strength to the Enamel of Primary Teeth

Successful clinical use of pit-and-fissure sealants relies on the sufficient etching of the enamel, field isolation and sealant retention. The etching time changes the physical and mechanical surface properties of the etched tooth tissues; therefore, it impacts both etching depth and the bond strength of sealants to the enamel. We examined if reducing the recommended 15 s etching time of primary teeth enamel affects the micro-shear bond strength (µSBS) of pit-and-fissure sealants. The cusps of forty non-carious, extracted human primary molars were separately etched for 8, 15 or 30 s. Then, a pit-and-fissure sealant was placed and light-cured. The µSBS values were evaluated and compared among the three groups. The mean µSBS values ± standard deviations were 34.68 ± 16.93, 34.19 ± 17.35 and 36.56 ± 16.57 MPa in the cusps etched for 8, 15 and 30 s, respectively. No statistically significant differences in µSBS were observed among the three test groups. In this study, we showed for the first time that the recommended etching time of primary teeth enamel may be reduced from 15 to 8 s without compromising the µSBS of the sealant. Further evaluations in a clinical setting are warranted.

Effects of rotary brush active application on enamel etching patterns of self-etch adhesive systems

Abstract.

Limited Etching Time Increases Self-adhesive Resin Cement Adhesion to Enamel

AIM

To evaluate the influence of different enamel etching times on the bond strength of two self-adhesive resin cements (RCs) with and without thermocycling (TMC).

METHODS

One hundred twenty bovine teeth were used. Blocks of enamel (8×4×2mm) were obtained, polished, and randomly divided into two groups, according to the RC used: MaxCem Elite or RelyX U200. Groups were subdivided into four groups (n=16), according to the etching time: Control (0 seconds), 5 seconds, 10 seconds, and 20 seconds. Three RC cylinders (1-mm diameter) were built on each enamel block. The specimens were submitted to two storage conditions: 24 hours in distilled water or TMC (5000 cycles/5°C-55°C). Afterward, the specimens were submitted to the shear bond strength (SBS) test. The failure modes and adhesive interfaces were analyzed by scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM). Data were analyzed with three-way analysis of variance (ANOVA) and Tukey test (α=0.05).

RESULTS

Etching increased the SBS for both the RCs,especially forthe groups etched for 5 and 10 seconds. TMC affected negatively the SBS of the control groups (p<0.05). No resin tags were observed in control groups, and the formation of tags was time dependent.

CONCLUSION

The 10 seconds etching time was more effective in increasing the enamel-resin bond strength. TMC negatively affected bond strength in specimens without acid etching.

Comparative analysis of bond strength and microleakage of newer generation bonding agents to enamel and dentin: An in vitro study

Aims

This study aims to evaluate the bond strength (BS) and microleakage (ML) of the newer bonding agents to enamel and dentin.

Objective

(1) To analyze the BS between self-etch and total-etch adhesives. (2) To analyze the depth of ML between self-etch and total-etch adhesives.

Materials and Methods

Sixty mandibular premolars were fabricated and randomly divided into three groups: Group I (n = 20)-bonded with self-etch adhesive + nanohybrid, Group II (n = 20) with total-etch adhesive + micro hybrid and Group III (n = 20) with total-etch adhesive + nanocomposite. Teflon ring molds were used to make composite resin cylinders bonded to the buccal surface. Class II box cavity was prepared on the samples' proximal surface and condensed with composite resin with each group's specific bonding protocol. Shear BS and ML testing were conducted, and data analyzed.

Statistical Analysis

Kruskal-Wallis analysis was done to statistically differentiate the BS and ML between the three experimental groups; the P < 0.05, it showed a statistically significant difference. Intergroup comparison was made using the Mann-Whitney U test.

Conclusions

Within this study's limitation, resin bonded with self-etch G-Premio Bond used in selective etch technique showed the highest BS and resistance to ML.

Effects of alumina airborne-particle abrasion on the surface properties of CAD/CAM composites and bond strength to resin cement

The purpose of this study is to clarify physical and chemical changes in surfaces of CAD/CAM composites caused by alumina airborne-particle abrasion and its effect on adhesive bonding. Our study involved three dispersed filler (DF)-based and a polymer-infiltrated ceramic network (PICN)-based CAD/CAM composites. Changes in the surface morphologies of the composites were examined, and surface free energy (SFE) analysis was performed based on Owens-Wendt theory. The influence of the abrasion on the bond strengths of CAD/CAM composites to the resin cement was characterized by shear bond strength (SBS) test. The abrasion increased the roughness of the composites. The SFE analysis showed that the abrasion significantly increased the dispersive component but decreased the polar component of the SFE associated with the DF-based composites, while no change occurred for those of the PICN-based composite. The abrasion slightly improved the SBSs for the DF-based composites but not that of the PICN-based composite.

Influence of different phosphoric acids before application of universal adhesive on the dental enamel

BACKGROUND

There are different etching gels available, which have different composition, different pH, and different viscosity, and there is little information in the literature comparing all these products.

OBJECTIVE

To evaluate the mean microshear bond strength and morphological characteristics of tooth enamel by evaluating different phosphoric acids combined with a universal adhesive system.

MATERIALS AND METHODS

Eighty-four enamel samples were used, which were divided according to the acid conditioning: G1: Scotchbond Etchant (3M Oral Care), G2: Ultra-Etch (Ultradent), G3: Eco-Etch (IvoclarVivadent), G4: ETCH-37 with BAC (Bisco), G5: Etching gel (Densell), G6: Condac 37 (FGM), and G7: Scotchbond Universal Adhesive (3M Oral Care) in self-etch mode. For the adhesive procedure, Scotchbond Universal Adhesive was the one used as indicated the manufacturer's instructions, 0.9-mm-diameter resin cylinders were placed. The microshear bond strength test was performed after being stored for 24 hours in water. The morphological characteristics of tooth enamel were analyzed using the Raman confocal microscope alpha300RA. The analysis of variance (ANOVA) test and Tukey post-test were used to analyze the differences between the groups.

RESULTS

The mean microshear bond strength values obtained for groups 1, 4, 5 were significantly greater than groups 2, 3, 6 and 7 (p < .05). All groups presented demineralization after the application of the etching acid, and few signs of demineralization were evident in group 7.

CONCLUSIONS

Acid-etching with ETCH-37 with BAC, Etching gel, and Scotchbond Etchant improved the adhesive strength in the enamel using an universal adhesive, and acid-etching with Condac 37, Ultra-Etch, and Eco-Etch provides similar adhesive strength values to self-etch mode of universal adhesive.

CLINICAL SIGNIFICANCE

All acid etchants should be considered as different. The test confirms that enamel etching prior to the application of a universal adhesive system depends on the selected acid etchand product.

The impact of etching time and material on bond strength of self-adhesive resin cement to eroded enamel

The purpose of this study was to assess the effect of pre-etching time and material on shear bond strength (SBS) of self-adhesive resin cements to eroded and sound enamel. Eroded enamel specimens were assigned into 5 groups (n=20 each) based on enamel surface treatment as follow: Group N, eroded enamel (without surface pre-treatment); Group PH15, 35% H₃PO₄ etching for 15 s; Group PH30, 35% H₃PO₄ etching for 30 s; Group L30, 20% lactic acid etching for 30 s and Group L60, 20% lactic acid etching for 60 s.Composite blocks were fabricated and cemented to enamel surfaces with one of two self-adhesive cements. Notched-edge SBS was assessed. Bond strength of self-adhesive cement to eroded enamel surface significantly enhanced following application of 20% lactic acid for 30 s.

Bond strength and adhesive interfacial micromorphology of self-adhesive resin cements: Effect of reduced times of pre-etching

Background

Although acid-etching could increase enamel bond strength of self-adhesive (SA) cements, it may lead to negative effect on dentin. The aim of this study was to assess the effect of shortening of phosphoric acid pre-etching duration on enamel/ dentin shear bond strength (SBS) and interfacial microstructure of Panavia SA Luting Plus (PASA) and Bifix SE (BXSE).

Material and Methods

For both enamel and dentin, effect of pre-etching time was significant (p<0.001); however, effect of cement brand and the interaction of two factors was significant only for dentin (p≤0.008). Three pre-etching times increased SBS of both cements to enamel and BXSE to dentin. In case of dentin SBS of PASA, this improvement was significant only for 5 and 10 seconds (p<0.001). Adding acid-etching in the three times to both cements similarly improved interfacial adaptation, particularly for enamel.

Results

The evaluations of the biofilm elimination showed results that indicate that the 4% sodium hypochlorite group with positive pressure irrigation presented significant differences with the group that had irrigation with sodium hypochlorite activated with XP-endo Finisher and the chlorhexidine groups to 2% (P<0.05).

Conclusions

Interfacial bond strength and adaptation of SA cements used in this study were improved following addition of enamel/dentin etching step for a short time. This was not exceeded for longer times than 5-second.

Key words:Dentin bond strength, enamel bond strength, pre-etching time, self-adhesive cement.

Comparison of shear bond strength of orthodontic brackets bonded with a universal adhesive using different etching methods

Objective:

The aim of this study was to compare the effects of three enamel etching modes - laser-etch, self-etch and acid-etch (5, 10 and 15 s) - on bracket bonding, using a universal adhesive.

Methods:

Eighty-four maxillary premolars were randomly divided into seven groups (n=12) based on the etching method and the adhesive used for bracket bonding. After water storage and thermocycling, shear bond strength was measured, and adhesive remnant index scores on debonded enamel were determined.

Results:

There were significant differences between the seven groups regarding bond strength values (p< 0.001). The highest values were observed in universal adhesive with laser etching group, while Transbond XT with acid or laser etching, and universal adhesive used in self-etch mode demonstrated the lowest bond strength. The universal adhesive with the three different etching times presented with statistically similar results, all showing an improvement in bond strength, compared with Scotchbond universal (SBU)/SE.

Conclusions:

The universal adhesive evaluated in the present study demonstrated statistically similar bond strengths to conventional orthodontic adhesive in self-etch mode. The bond strength can be improved by adding an initial acid etching or laser conditioning step, although enamel damage was observed in some cases.

The role of spatial frequency analysis in correlating atomic force microscopy and optical profilometry with self-etch adhesive enamel bond fatigue durability

The purpose of this study was to: (a) evaluate the role of enamel surface roughness on bond fatigue durability and (b) evaluate statistical differences in roughness values based on measurement technique, including the use of spatial filtering for optical profilometry (OP). OptiBond XTR (Kerr Corp), Prime & Bond elect (DENTSPLY Caulk), Scotchbond Universal (3 M Oral Care), and XTR pre-etched with Ultra-Etch phosphoric acid (35%) (Ultradent) self-etch adhesives were used to treat enamel. A flat ground enamel surface was included as a control. Atomic force microscopy (AFM) and OP were used to measure the surface topography of each enamel surface following the application of adhesives. AFM, OP, and filtered OP (FOP) roughness values, where FOP was designed to only include the lateral spatial resolution consistent with AFM roughness values, were collected. Spatial resolution filtering with OriginPro was used to compare line scans from the two imaging techniques and generate the FOP group. These micro- versus nanoscale lateral roughness values were correlated with shear bond and shear fatigue strengths of the adhesives bonded to enamel. Roughness values showed differences based on measurement technique and strong correlations with bond and fatigue strength. The filtered OP group demonstrated the importance of careful usage and reporting of atomic force microscopy and OP metrics in adhesive dentistry. Best practices for surface roughness analysis were also discussed.

Effect of Preetching on Microleakage with All-In-One Adhesives Using Calcium-Based Desensitizers: An In vitro Study

Objectives

The aim of this study was to evaluate the effect of calcium-based desensitizers on the microleakage with and without preetching enamel in Class V cavities restored with all-in-one adhesives.

Materials and Methods

Class V cavities were prepared on the buccal surfaces of 100 extracted human premolars. A total of 100 box-shaped cavities were divided into five groups (n = 20). Group 1 - no desensitizer was applied and Groups 2 and 4 - desensitizer (CCP-ACP and Novamin) was applied, respectively, followed by the application of G-Bond and restored with composite restoration. Groups 3 and 5 are same as Group 2 and 4, but preetching of enamel was done for 3 s after desensitizers application. The teeth were thermocycled and the specimens were examined for microleakage using methylene blue as a marker. The teeth were sectioned buccolingually and evaluated for microleakage under stereomicroscope and the scores obtained were analyzed with Kruskal-Wallis and Mann-Whitney tests.

Results

Statistically significant difference existed between Groups 2 and 3 (P < 0.05). There was also statistically significant difference between Groups 4 and 5 (P < 0.05). Groups 3 and 5 showed significantly less microleakage (P < 0.05). No statistically significant difference in microleakage values was observed between the two desensitizers CCP-ACP and Novamin.

Conclusion

The application of calcium-containing desensitizers with selective etch enamel technique in all-in-one adhesives could be considered an advisable procedure to minimize microleakage.

Relationship between mechanical properties and bond durability of short fiber-reinforced resin composite with universal adhesive

The purpose of this study was to determine the relationship between mechanical properties and bond durability of short fiber-reinforced resin composite with universal adhesive. As controls, micro-hybrid and nano-hybrid resin composites were tested. The universal adhesives used were Scotchbond Universal, Adhese Universal, and G-Premio Bond. The fracture toughness and flexural properties of resin composites, and shear bond strength and shear fatigue strength of universal adhesive with resin composite using both total-etch and self-etch modes were determined. In the results, short fiber-reinforced resin composite showed significantly higher fracture toughness than did micro-hybrid and nano-hybrid resin composites. The flexural strength and modulus of short fiber-reinforced and nano-hybrid resin composites were significantly lower than were those of micro-hybrid resin composites. Regardless of etching mode, the shear bond strength of universal adhesives with short fiber-reinforced resin composite did not show any significant differences from micro-hybrid and nano-hybrid resin composites. The shear fatigue strength of universal adhesives with short fiber-reinforced resin composite and micro-hybrid resin composites were significantly higher than that of nano-hybrid resin composites. The results of this study suggest that the mechanical properties of short fiber-reinforced resin composite improve their bond durability with universal adhesive.

Effect of Oxygen Inhibition Layer of Universal Adhesives on Enamel Bond Fatigue Durability and Interfacial Characteristics With Different Etching Modes

OBJECTIVE

The purpose of this study was to evaluate the effect of the oxygen inhibition layer of universal adhesive on enamel bond fatigue durability and interfacial characteristics with different etching modes.

METHODS

The three universal adhesives used were Scotchbond Universal Adhesive (3M ESPE, St Paul, MN, USA), Adhese Universal (Ivoclar Vivadent, Schaan, Lichtenstein), and G-Premio Bond (GC, Tokyo, Japan). The initial shear bond strength and shear fatigue strength to enamel was determined in the presence and absence of the oxygen inhibition layer, with and without phosphoric acid pre-etching. The water contact angle was also measured in all groups using the sessile drop method.

RESULTS

The enamel bonding specimens with an oxygen inhibition layer showed significantly higher (p<0.05) initial shear bond strengths and shear fatigue strengths than those without, regardless of the adhesive type and etching mode. Moreover, the water contact angles on the specimens with an oxygen inhibition layer were significantly lower (p<0.05) than on those without, regardless of etching mode.

CONCLUSION

The results of this study suggest that the oxygen inhibition layer of universal adhesives significantly increases the enamel bond fatigue durability and greatly changes interfacial characteristics, suggesting that the bond fatigue durability and interfacial characteristics of these adhesives strongly rely on its presence.

Influence of photoirradiation conditions on dentin bond durability and interfacial characteristics of universal adhesives

The influence of photoirradiation conditions on dentin bond durability and interfacial characteristics of universal adhesives was investigated. Universal adhesives were applied to the dentin surfaces and photoirradiated with 100 mW/cm² for 40 s, 200 mW/cm² for 20 s, and 400 mW/cm² for 10 s. A resin composite was bonded to dentin to determine shear bond strength after 24 h water storage and 30,000 thermal cycles, and water contact angle of cured adhesive were measured by the sessile drop method. Greater dentin bond strengths after 24 h water storage and 30,000 thermal cycles were achieved under these conditions at light intensity exceeding 200 mW/cm². Universal adhesives photoirradiated above 200 mW/cm² exhibited significantly higher water contact angles than those at 100 mW/cm². The results of this study suggested that the photoirradiation conditions affect the dentin bond durability and interfacial characteristics of universal adhesives even at the same total energy.

Interfacial Characteristics and Bond Durability of Universal Adhesive to Various Substrates

Objective: This study investigated the interfacial characteristics and bond durability of universal adhesives to various substrates.

Methods and Materials: Two universal adhesives were used: 1) Scotchbond Universal and 2) G-Premio Bond. The substrates used were bovine enamel and dentin with or without phosphoric acid etching, resin composite, lithium disilicate and leucite-reinforced glass ceramics, zirconia, and metal alloys. The surface free energy and the parameters of various substrates and of substrates treated by adhesive after light irradiation were determined by measuring the contact angles of three test liquids. Resin composite was bonded to the various substrates to determine shear bond strength after 24 hours water storage and 10,000 thermal cycles. A one-way analysis of variance (ANOVA) and the Tukey post hoc test were used for the surface free energy data, and a two-way ANOVA and the Tukey post hoc test were used for analysis of shear bond strength data (α=0.05).

Results: The interfacial characteristics of the various substrates show significant differences depending on the type of substrate, but the interfacial characteristics of substrate treated by adhesive after light irradiation did not show any significant differences regardless of the substrate used. The bond durability of two universal adhesives to various substrates differs depending on the type of substrate and the adhesive.

Conclusions: The results of this study suggest that universal adhesives modify the interfacial characteristics of a wide range of substrates and create a consistent surface, but the bond durability of universal adhesive to various substrates differs depending on the type of substrate and the adhesive.