Loratidine buccal films for allergic rhinitis: development and evaluation

Incorporation of Loratadine-Cyclodextrin Complexes in Oral Thin Films for Rapid Drug Delivery

Rapidly dissolving polymer thin films, or oral thin films (OTFs), have recently emerged as an improved oral drug delivery vehicle with its ability to bypass liver first pass metabolism, longer shelf-life, and simpler transport and distribution requirements, compared to traditional tablets and liquid formulations. Loratadine (LOR), an antihistamine commonly used to treat allergic rhinitis, undergoes liver first pass metabolism and is a prime candidate for incorporation within an OTF. However, loratadine is a BCS II drug with low aqueous solubility. Herein, the solubility of loratadine was improved by complexation with methyl β-cyclodextrin (MBCD) by co-evaporation of 2:1, 1:1, and 1:2 LOR:MBCD ratios and incorporation into a pullulan-based OTF at 4 wt% by solvent casting at 50 °C for 30 - 35 min. A therapeutically relevant 10 mg LOR dose could be prepared in a 3 cm by 3 cm OTF. The feasibility of complexation was observed with a Bs-type phase solubility diagram, and complexation itself was confirmed via differential scanning calorimetry (DSC) by disappearance of the LOR melting peak, Fourier-transform infrared spectroscopy (FTIR) by shifting of the C=O peak, via 1H NMR spectroscopy by downfield shifting and change in peak multiplicity of the LOR aromatic protons, and via diffusion-ordered spectroscopy by a decrease in the diffusion coefficient of LOR:MBCD complex. LOR:MBCD could be incorporated homogeneously throughout an OTF, and LOR:MBCD OTFs exhibited reasonable mechanical strength and endured 12 ± 3 folds before breaking. LOR:MBCD OTFs disintegrated within 38 ± 10 s. The cumulative in vitro release of LOR:MBCD OTFs peaked at 80 % within 3-4 min of dissolution, and LOR in LOR:MBCD OTFs exhibited permeability across a 0.22 μm nitrocellulose membrane, demonstrating its applicability as a rapid drug delivery vehicle.

Design, Development, Evaluation, and In Vivo Performance of Buccal Films Embedded with Paliperidone-Loaded Nanostructured Lipid Carriers

The therapeutic effectiveness of paliperidone in the treatment of schizophrenia has been limited by its poor oral bioavailability; hence, an alternative route could be appropriate. This study investigates the feasibility of developing a buccal film impregnated with paliperidone-loaded nanostructured lipid carriers (NLCs) and assesses the potential to enhance its bioavailability. Box-Behnken-based design optimization of NLCs was performed by examining the particles' physical characteristics. The polymeric film was used to load optimized NLCs, which were then assessed for their pharmaceutical properties, permeability, and pharmacokinetics. The optimization outcomes indicated that selected formulation variables had a considerable (p < 0.05) impact on responses such as particle size, entrapment efficiency, and % drug release. Desired characteristics such as a negative charge, higher entrapment efficiency, and nanoparticles with ideal size distribution were shown by optimized NLC dispersions. The developed film demonstrated excellent physico-mechanical properties, appropriate texture, good drug excipient compatibility (chemically stable formulation), and amorphous drug nature. A sustained Weibull model drug release (p < 0.0005) and superior flux (~5-fold higher, p < 0.005) were seen in NLC-loaded film compared to plain-drug-loaded film. The pharmacokinetics profile in rabbits supports the goal of buccal therapy as evidenced by significantly higher AUC0-12 (p < 0.0001) and greater relative bioavailability (236%) than the control. These results support the conclusion that paliperidone-loaded NLC buccal film has the potential to be an alternate therapy for its effective administration in the treatment of schizophrenia.

Loratadine oral bioavailability enhancement via solid dispersion loaded oro-dispersible films: Formulation, characterization and pharmacokinetics

Loratadine (LRD) belongs to second-generation tricyclic H1 antihistamine class, known for its non-sedating properties in allergic reactions. H1 antihistamines avoid and block the responses to allergens or histamine in nose and conjunctivae, thereby abolishing itching, congestion and sneezing. LRD is a Biopharmaceutical Class System (BCS) class II drug with dissolution or solubility limited absorption which limited the oral bioavailability and therapeutic efficacy of LRD. To improve the oral bioavailability of LRD for allergic disease (urticaria) treatment, LRD solid dispersions (LRD-SDs) were integrating into oro-dispersible films (ODFs). LRD-SDs were prepared through hot-melt extrusion method (HME) using d-alpha-tocopherol polyethylene glycol 1000 succinate (TPGS-1000), and polyvinyl caprolactam-polyvinyl acetate-polyethylene glycol graft copolymer (SP). Subsequently, LRD-SDs were incorporated in ODFs by solvent casting method. The physicochemical and mechanical properties of LRD solid dispersions-loaded oro-dispersible films (LRD-SDs-ODFs), were evaluated. The in-vitro dissolution, ex-vivo permeation, oral bioavailability, and pharmacodynamics studies were conducted to evaluate LRD-SDs-ODFs efficiency. LRD-SDs-ODFs showed superior solubility and in-vitro dissolution results compared to that of pure LRD (p < 0.05). The solubility of the LRD-SD coded as LTS-4 was 190 times higher than the pure drug in aqueous media. The average hydrodynamic particle size (PS), polydispersity index (PDI), and zeta potential (ZP) of SD particles were 76 ± 2.1 nm, 0.20 ± 0.08 and - 19.16 ± 1.4 mV, respectively. Moreover, differential scanning calorimetry (DSC) and X-ray diffraction (XRD) results confirmed the amorphousness of LRD in LRD-SDs-ODFs. The permeability flux of LRD was 44.6 ± 3.1 μg/cm2/h from DPF-5 formulation. Likewise, in vivo oral bioavailability of DPF-5 in Sprague-Dawley rats was significantly increased (p < 0.05) compared to free LRD. Further, wheal area was reduced 20 % higher than LRD in 8 h (p < 0.05). Overall, LRD-SDs-ODFs considerably enhanced LRD solubility, dissolution rate, bioavailability, and antihistaminic efficacy. Our findings show that SDs-ODFs is an effective carrier system for delivering poorly soluble LRD.

Stability, Permeability and Cytotoxicity of Buccal Films in Allergy Treatment

Oral mucoadhesive systems, such as polymer films, are among innovative pharmaceutical products. These systems can be applied in swallowing problems and can also be used in geriatrics and paediatrics. In our earlier work, we successfully formulated buccal mucoadhesive polymer films, which contained cetirizine-hydrochloride (CTZ) as the API. The present study focused on investigating the stability and permeability of the prepared films. The stability of the films was studied with an accelerated stability test. During the stability test, thickness, breaking hardness and in vitro mucoadhesivity were analysed. Furthermore, the interactions were studied with FT-IR spectroscopy, and the changes in the amount of the API were also monitored. Cytotoxicity and cell line permeability studies were carried out on TR 146 buccal cells. Compositions that can preserve more than 85% of the API after 6 months were found. Most of the compositions had a high cell viability of more than 50%. Citric acid (CA) decreased the stability and reduced every physical parameter of the films. However, cell line studies showed that the permeability of the films was enhanced. In our work, we successfully formulated CTZ-containing buccal films with adequate stability, high cell viability and appropriate absorption properties.

An Updated Overview of the Emerging Role of Patch and Film-Based Buccal Delivery Systems

Buccal mucosal membrane offers an attractive drug-delivery route to enhance both systemic and local therapy. This review discusses the benefits and drawbacks of buccal drug delivery, anatomical and physiological aspects of oral mucosa, and various in vitro techniques frequently used for examining buccal drug-delivery systems. The role of mucoadhesive polymers, penetration enhancers, and enzyme inhibitors to circumvent the formulation challenges particularly due to salivary renovation cycle, masticatory effect, and limited absorption area are summarized. Biocompatible mucoadhesive films and patches are favored dosage forms for buccal administration because of flexibility, comfort, lightness, acceptability, capacity to withstand mechanical stress, and customized size. Preparation methods, scale-up process and manufacturing of buccal films are briefed. Ongoing and completed clinical trials of buccal film formulations designed for systemic delivery are tabulated. Polymeric or lipid nanocarriers incorporated in buccal film to resolve potential formulation and drug-delivery issues are reviewed. Vaccine-enabled buccal films have the potential ability to produce both antibodies mediated and cell mediated immunity. Advent of novel 3D printing technologies with built-in flexibility would allow multiple drug combinations as well as compartmentalization to separate incompatible drugs. Exploring new functional excipients with potential capacity for permeation enhancement of particularly large-molecular-weight hydrophilic drugs and unstable proteins, oligonucleotides are the need of the hour for rapid advancement in the exciting field of buccal drug delivery.

Development of Mucoadhesive Buccal Film for Rizatriptan: In Vitro and In Vivo Evaluation

The reduced therapeutic efficacy of rizatriptan in migraine treatment is primarily due to low oral bioavailability and extensive first pass metabolism. The purpose of this investigation was to optimize the thin mucoadhesive buccal film of rizatriptan and assess the practicability of its development as a potential substitute for conventional migraine treatment. Buccal films (FR1-FR10) were fabricated by a conventional solvent casting method utilizing a combination of polymers (Proloc, hydroxypropyl methylcellulose and Eudragit RS 100). Drug-loaded buccal films (F1-F4) were examined for mechanical, mucoadhesive, swelling and release characteristics. In vivo pharmacokinetics parameters of selected buccal film (F1) in rabbits were compared to oral administration. Films F1-F4 displayed optimal physicomechanical properties including mucoadhesive strength, which can prolong the buccal residence time. A biphasic, complete and higher drug release was seen in films F1 and F4, which followed Weibull model kinetics. The optimized film, F1, exhibited significantly higher (p < 0.005) rizatriptan buccal flux (71.94 ± 8.26 µg/cm²/h) with a short lag time. Film features suggested the drug particles were in an amorphous form, compatible with the polymers used and had an appropriate surface morphology suitable for buccal application. Pharmacokinetic data indicated a significantly higher rizatriptan plasma level (p < 0.005) and C_max (p < 0.0001) upon buccal film application as compared to oral solution. The observed AUC_0-12h (994.86 ± 95.79 ng.h/mL) in buccal treatment was two-fold higher (p < 0.0001) than the control, and the relative bioavailability judged was 245%. This investigation demonstrates the prospective of buccal films as a viable and alternative approach for effective rizatriptan delivery.

Formulation and Optimization of Sodium Alginate Polymer Film as a Buccal Mucoadhesive Drug Delivery System Containing Cetirizine Dihydrochloride

Currently, pharmaceutical companies are working on innovative methods, processes and products. Oral mucoadhesive systems, such as tablets, gels, and polymer films, are among these possible products. Oral mucoadhesive systems possess many advantages, including the possibility to be applied in swallowing problems. The present study focused on formulating buccal mucoadhesive polymer films and investigating the physical and physical–chemical properties of films. Sodium alginate (SA) and hydroxypropyl methylcellulose (HPMC) were used as film-forming agents, glycerol (GLY) was added as a plasticizer, and cetirizine dihydrochloride (CTZ) was used as an active pharmaceutical ingredient (API). The polymer films were prepared at room temperature with the solvent casting method by mixed two-level and three-level factorial designs. The thickness, tensile strength (hardness), mucoadhesivity, surface free energy (SFE), FTIR, and Raman spectra, as well as the dissolution of the prepared films, were investigated. The investigations showed that GLY can reduce the mucoadhesivity of films, and CTZ can increase the tensile strength of films. The distribution of CTZ proved to be homogeneous in the films. The API could dissolve completely from all the films. We can conclude that polymer films with 1% and 3% GLY concentrations are appropriate to be formulated for application on the buccal mucosa as a drug delivery system.

Effects of Sucrose Palmitate on the Physico-Chemical and Mucoadhesive Properties of Buccal Films

In our current research, sucrose palmitate (SP) was applied as a possible permeation enhancer for buccal use. This route of administration is a novelty as there is no literature on the use of SP in buccal mucoadhesive films. Films containing SP were prepared at different temperatures, with different concentrations of SP and different lengths of hydroxypropyl methylcellulose (HPMC) chains. The mechanical, structural, and in vitro mucoadhesive properties of films containing SP were investigated. Tensile strength and mucoadhesive force were measured with a device and software developed in our Institute. Positron annihilation lifetime spectroscopy (PALS) and X-ray powder diffractometry (XRPD) were applied for the structure analysis of the films. Mucoadhesive work was calculated in two ways: from the measured contact angle and compared with direct mucoadhesive work, which measured mucoadhesive force, which is direct mucoadhesion work. These results correlate linearly with a correlation coefficient of 0.98. It is also novel because it is a new method for the determination of mucoadhesive work.

HPMC- and PLGA-Based Nanoparticles for the Mucoadhesive Delivery of Sitagliptin: Optimization and In Vivo Evaluation in Rats

Mucoadhesive nanoparticles represent a potential drug delivery strategy to enhance the therapeutic efficacy in oral therapy. This study assessed the prospective of developing HPMC- and PLGA-based nanoparticles using a nanospray drier as a mucoadhesive extended release drug delivery system for sitagliptin and evaluated their potential in an animal model. Nanoparticles were prepared using a Buchi^® B-90 nanospray drier. Optimization of particle size was performed using response surface methodology by examining the influence of spray-drying process variables (inlet temperature, feed flow, and polymer concentration) on the particle size. The prepared nanoparticles were characterized for various physicochemical characteristics (yield, drug content, morphology, particle size, thermal, and crystallographic properties) and assessed for drug release, stability, and mucoadhesive efficacy by ex vivo and in vivo studies in rats. A linear model was suggested by the design of the experiments to be the best fit for the generated design and values. The yield was 77 ± 4%, and the drug content was 90.5 ± 3.5%. Prepared nanoparticles showed an average particle size of 448.8 nm, with a narrow particle size distribution, and were wrinkled. Thermal and crystallographic characteristics showed that the drug present in the nanoparticles is in amorphous dispersion. Nanoparticles exhibited a biphasic drug release with an initial rapid release (24.9 ± 2.7% at 30 min) and a prolonged release (98.9 ± 1.8% up to 12 h). The ex vivo mucoadhesive studies confirmed the adherence of nanoparticles in stomach mucosa for a long period. Histopathological assessment showed that the formulation is safe for oral drug delivery. Nanoparticles showed a significantly higher (p < 0.05) amount of sitagliptin retention in the GIT (gastrointestinal tract) as compared to control. The data observed in this study indicate that the prepared mucoadhesive nanoparticles can be an effective alternative delivery system for the oral therapy of sitagliptin.

Mucoadhesive buccal film of almotriptan improved therapeutic delivery in rabbit model

Administration of almotriptan as an oral therapy is largely limited because of poor aqueous solubility and rather low bioavailability. The aim of present investigation was to formulate oral mucoadhesive film of almotriptan to improve the drug delivery and desired therapeutic effects. Placebo films (F1-F8) were prepared by varying the concentrations of Proloc 15 (7.5-15% w/v) and Eudragit RL 100/RS 100 (15-30% w/v) polymers. Physicomechanical and pharmaceutical characteristics of drug loaded films (FA1-FA4) were examined. Selected FA4 film was evaluated in vivo by assessing the pharmacokinetic profile and compared with oral therapy in rabbits. FA1-FA4 films exhibited excellent physicomechanical properties and rapid hydration. A biphasic and considerably greater drug release (p < 0.05) was observed in FA3 and FA4 films contain higher amount of hydrophilic polymer. The rate of permeation of almotriptan was found to be significantly higher in FA4 than FA3 film (p < 0.005). Fourier transform infrared spectral scan indicates no incompatibility exists between the drug and polymers used. Differential scanning calorimetry thermogram represents the evidence of almotriptan amorphization and molecular dispersion of it in the film. Scanning electron microscopy images shows that FA4 possess good morphological features and hence suitable for use in the buccal application. In vivo data demonstrated rapid and efficient absorption (p < 0.005) of almotriptan with greater AUC_0-12 (>2 folds, p < 0.0001) by FA4 film as compared to oral (control). In general, the data established the potential of FA4 film to improve the therapeutic delivery of almotriptan and offers a promising option in migraine therapy.

An updated overview with simple and practical approach for developing in vitro-in vivo correlation

Preclinical Research & Development An in vitro-in vivo correlation (IVIVC) is as a predictive mathematical model that demonstrates a key role in the development, advancement, evaluation and optimization of extended release, modified release and immediate release pharmaceutical formulations. A validated IVIVC model can serve as a surrogate for bioequivalence studies and subsequently save time, effort and expenditure during pharmaceutical product development. This review discusses about different levels of correlations, general approaches to develop an IVIVC by mathematical modelling, validation, data analysis and various applications. In the current setting, the dearth of success associated with IVIVC is due to complexity of underlying scientific principles as well as the practice of fitting/matching in vivo plasma level-time data with in vitro dissolution profile. Hence, a simple, straightforward practical means to predict plasma drug levels by convolution technique and percentage drug absorbed computed from in vitro dissolution profile based on deconvolution method are illustrated. The bioavailability/bioequivalence assessment and evaluation are frequently validated by the pharmacokinetic parameters such as maximum concentration, time to reach maximum concentration, and area under the curve. The implementation of a quality by design manufacturing based on in vivo bioavailability and clinically relevant dissolution specification are recommended because corresponding design safe space will guarantee that all batches from relevant products are met with sufficient quality and bioperformance. Recently, United States Food and Drug Administration and European Medicines Agency have proposed that in silico/physiologically based pharmacokinetic modelling can be used in decision making during preclinical experiments as well as to recognize the dissolution profiles that can forecast and ensure the desired clinical performance.

Mucoadhesive buccal film containing ornidazole and dexamethasone for oral ulcers: in vitro and in vivo studies

A bilayered mucoadhesive buccal film containing a combination of ornidazole (OD) and dexamethasone sodium phosphate (DEX) was prepared using solvent casting to treat oral ulcers. Films were systematically evaluated in vitro to obtain the optimum formulation. The therapeutic effects of these films were investigated in the rabbit oral ulcer model and the in vivo release of OD and DEX in the human oral cavity was also evaluated. The backing layer contained ethyl cellulose and an optimal mucoadhesive layer containing both OD and DEX was produced. Films from the optimum formulation were 0.427 ± 0.015 mm thick, weighed 55.89 ± 0.79 mg, and had a surface pH of 6.34 ± 0.01. The drug content of the optimum formulation approximated the theoretical value with good uniformity (2.959 ± 0.106 mg/cm² for OD and 0.877 ± 0.031 mg/cm² for DEX). The formulation showed favorable swelling characteristics and both drugs were released at >95% after 4 h. Moreover, the compound film had a statistically significant effect on mucosal repair and reduced ulcer inflammation without stimulating the human oral mucosa. C_max of OD in saliva was 37.04 μg/ml and that of DEX was 9.737 μg/ml. Given promising therapeutic effects, the compound film developed here could become a local drug delivery device for treating oral ulcers.

Formulation and In Vitro Release Kinetics of Mucoadhesive Blend Gels Containing Matrine for Buccal Administration

Enterovirus 71 (EV71) is a pathogenic factor of severe hand, foot, and mouth disease (HFMD). No vaccine or specific treatment is currently available for EV71 infection. Hence, we developed a buccal mucoadhesive gel containing matrine to protect against HFMD. Mucoadhesive gels were prepared by Carbopol 974P and were combined with Carbopol 971P, sodium carboxymethyl cellulose (CMC-Na), or hydroxypropylmethy cellulose (HPMC K100M). The formulations were characterized in terms of tensile testing and continuous flow techniques for mucoadhesion. The rheological studies and in vitro drug release characteristics were also investigated. The results showed that combinations of two polymers significantly improved mucoadhesion, especially Carbopol 974P blended with HPMC. Carbopol 974P to HPMC blend ratios of 1:1 and 2:1 induced better mucoadhesion in the tensile test and continuous flow method, respectively. The most sustained release was obtained at a Carbopol 974P to HPMC ratio of 2.5:1. A predominantly non-Fickian diffusion release mechanism was obtained. The gel containing 2.5% Carbopol 974P combined with 1% HPMC showed good mucoadhesion properties and sustained drug release.

Loratadine bioavailability via buccal transferosomal gel: formulation, statistical optimization, in vitro/in vivo characterization, and pharmacokinetics in human volunteers

Loratadine (LTD) is an antihistaminic drug that suffers limited solubility, poor oral bioavailability (owing to extensive first-pass metabolism), and highly variable oral absorption. This study was undertaken to develop and statistically optimize transfersomal gel for transbuccal delivery of LTD. Transfersomes bearing LTD were prepared by conventional thin film hydration method and optimized using sequential Quality-by-Design approach that involved Placket-Burman design for screening followed by constrained simplex-centroid design for optimization of a Tween-80/Span-60/Span-80 mixture. The transferosomes were characterized for entrapment efficiency, particle size, and shape. Optimized transferosomes were incorporated in a mucoadhesive gel. The gel was characterized for rheology, ex vivo permeation across chicken pouch buccal mucosa, in vitro release, and mucoadhesion. Pharmacokinetic behavior of LTD formulations was investigated in healthy volunteers following administration of a single 10-mg dose. Optimal transferosomes characterized by submicron size (380 nm), spherical shape and adequate loading capacity (60%) were obtained by using quasi-equal ratio surfactant mixture. In terms of amount permeated, percentage released, and mucoadhesion time, the transferosomal gel proved superior to control, transferosome-free gel. Bioavailability of the transferosomal gel was comparable to Claritin® oral tablets. However, inter-individual variability in Cmax and AUC was reduced by 76 and 90%, respectively, when the buccal gel was used. Linear Correlation of in vitro release with in vivo buccal absorption fractions was established with excellent correlation coefficient (R2>0.97). In summary, a novel buccal delivery system for LTD was developed. However, further clinical investigation is warranted to evaluate its therapeutic effectiveness and utility.

Development of Polyethylene Glycol and Hard Fat-Based Mucoadhesive Tablets Containing Various Types of Polyvinyl Alcohols as Mucoadhesive Polymers for Buccal Application

Topical drug application has the advantage of avoiding systemic side effects. We attempted to develop a long-acting matrix-type tablet containing indomethacin (IM) with low physical stimulus and potent mucoadhesive force to treat pain caused by oral aphtha. A mixture of polyethylene glycol (PEG) and hard fat was used as the tablet base. Ethylcellulose was added to the base in an attempt to control drug release. Tablets with PEG as a base were also prepared for comparison. Polyvinyl alcohols (PVAs) with various degrees of saponification were added to increase the mucoadhesive force. From the optical microscopic observations, formulations using PEG and hard fat exhibit PEG/hard fat dispersions caused by the stabilizing effects of PVA. Although the tablets using PEG and hard fat showed sufficient adhesiveness and sustained drug release, those using PEG as the base did not. Drug release was controlled by the amount of hard fat and the saponification degree of PVA. The drug release rate was most increased in a tablet containing PVA with an intermediate degree of saponification, PEG and hard fat. From differential scanning calorimetry and powder X-ray diffraction, IM was considered to exist in the molecular phase. From the results of buccal administration of tablets to rats, highest tissue concentrations were observed in the tablet containing PVA with the intermediate degree of saponification using PEG and hard fat, and the plasma concentrations were sufficiently low in comparison.

Preparation and in-vivo evaluation of dimenhydrinate buccal mucoadhesive films with enhanced bioavailability

Dimenhydrinate (DMH)-loaded buccal bioadhesive films for the prevention and treatment of motion sickness were prepared and optimized. This study examines the rate of drug release from the films for prolonged periods of time to reduce or limit the frequency of DMH administration. Based on preliminary studies using various polymers and concentrations, hydroxyethylcellulose (2.5, 3.0, and 3.2%), and xanthan gum (2.8%) were chosen as matrix polymers. The films were analyzed with respect to their mechanical, physicochemical, bioadhesive, swelling, and in-vitro release properties. In in-vivo pharmacokinetic studies, xanthan gum-based DMH buccal film was associated with significantly increased DMH plasma levels between 1 h and 5 h after DMH dosing when compared with an oral drug solution. The area under the curve AUC0-7 h value of the mucoadhesive buccal film was two-fold higher than the oral DMH solution. Histological analysis revealed that DMH films cause mild morphological and inflammatory changes in rabbit buccal mucosa. The DMH buccal film is effective for approximately 7 h, thus representing an option for single-dose antiemetic therapy. This dosage regimen could be particularly beneficial for chain travelers who travel for long periods of time.

Development and evaluation of buccal films impregnated with selegiline-loaded nanospheres

Poor peroral therapeutic efficiency of selegiline is primarily due to the extensive hepatic metabolism and hence the need for an alternative route of administration. The present study is based on evaluation of a buccal film which is impregnated with selegiline nanospheres to enhance the systemic bioavailability. Selegiline-loaded nanospheres prepared using poly(lactide-co-glycolide) was embedded into buccal films (F₁-F₄) with varying polymer composition [hydroxypropyl methylcellulose and eudragit]. The developed films were evaluated for their physicomechanical properties, hydration, mucoadhesive strength, in vitro drug release and ex vivo permeation in order to identify the ideal system suitable for further development. In vivo studies were carried out on rabbits to assess the comparative pharmacokinetics profile of the selected buccal film with oral solution. Preliminary studies indicated that the prepared films exhibited excellent physical properties, adequate mucoadhesive strength and moderate hydration. In vitro drug release data of the buccal films (F₁, F₂ and F₃) showed distinct profiles. Permeation studies indicated higher steady-state flux from film F₃ (p < 0.0001) when compared to film F₂. In-vivo results of film (F₃) demonstrated significant increase in absorption (p < 0.0001), C_max (∼1.6-fold), T_max, AUC_0-α (∼3-fold, p < 0.0001) and improved bioavailability, when compared to control. This study concludes that the buccal delivery of selegiline using the developed buccal film (F₃) would be a promising alternative approach for the treatment of Parkinson's disease.

Buccal films of prednisolone with enhanced bioavailability

The conventional formulation of prednisolone is considered to be low in efficacy, primarily on account of their failure in providing and maintaining effective therapeutic drug levels. This study aims to focus on development of a mucoadhesive buccal delivery system with a twofold objective of offering a rapid as well as a prolonged delivery of prednisolone coupled with enhanced therapeutic efficacy. Buccoadhesive films of prednisolone were prepared by solvent-casting method using hydroxyl propyl methyl cellulose (K100), Carbopol 940 and/or Eudragit NE 40 D. Placebo films possessing the most desirable physicomechanical properties were selected for drug loading. The effect of polymer and its content on film properties, i.e. mucoadhesive strength, swelling and hydration, in vitro drug release was studied. Based on these studies, film F7D was selected for ex vivo permeation across porcine cheek mucosa. The steady state flux of prednisolone across the buccal mucosa was found to be 105.33 ± 32.07 µg/cm(2)/h. A comparative pharmacokinetic study of prepared film (F7D) and oral suspension of prednisolone was conducted. In vivo data of buccal film show greater bioavailability (AUC0-α: 24.26 ± 4.06 µg.h/ml versus 10.65 ± 2.15 µg.h/ml) and higher Cmax (2.70 ± 0.38 µg/ml versus 2.29 ± 0.32 µg/ml) value when compared to oral suspension. The data observed from this study highlight the feasibility of the buccal route as a viable option for delivery of prednisolone.