Novel ethylcellulose-coated pellets for controlled release of metoprolol succinate without lag phase: characterization, optimization andin vivoevaluation

Assessment of Mini-Tablets Coating Uniformity as a Function of Fluid Bed Coater Inlet Conditions

This study concerned the quality of mini-tablets’ coating uniformity obtained by either the bottom spray chamber with a classical Wurster distributor (CW) or a swirl distributor (SW). Mini-tablets with a diameter of 2.0, 2.5, and 3.0 mm were coated with hypromellose using two different inlet air distributors as well as inlet airflow rates (130 and 156 m³/h). Tartrazine was used as a colorant in the coating layer and the coating uniformity was assessed by spectrophotometric analysis of solutions obtained after disintegration of the mini-tablets (n = 100). Higher uniformity of coating material distribution among the mini-tablets was observed in the case of SW distributor, even for the biggest mini-tablets (d = 3.0 mm), with an RSD no larger than 5.0%. Additionally, coating thickness was evaluated by colorimetric analysis (n = 1000), using a scanner method, and expressed as a hue value. A high correlation (R = 0.993) between inter-tablet variability of hue and UV-Vis results was obtained. Mini-tablets were successfully coated in a fluid bed system using both a classical Wurster distributor as well as a swirl generator. However, regardless of the mini-tablets’ diameter, better film uniformity was achieved in the case of a distributor with a swirl generator.

Polymer Distribution and Mechanism Conversion in Multiple Media of Phase-Separated Controlled-Release Film-Coating

Phase-separated films of water-insoluble ethyl cellulose (EC) and water-soluble hydroxypropyl cellulose (HPC) can be utilized to tailor drug release from coated pellets. In the present study, the effects of HPC levels and the pH, type, ionic strength and osmolarity of the media on the release profiles of soluble metoprolol succinates from the EC/HPC-coated pellets were investigated, and the differences in drug-release kinetics in multiple media were further elucidated through the HPC leaching and swelling kinetics of the pellets, morphology (SEM) and water uptake of the free films and the interaction between the coating polymers and the media compositions. Interestingly, the drug release rate from the pellets in different media was not in agreement with the drug solubility which have a positive correlation with the drug dissolution rate based on Noyes–Whitney equation law. In particular, the drug release rate in acetate buffer at pH 4.5 was faster than that in other media despite the solubility of drug was relatively lower, regardless of the HPC levels. It may be attributed to the mutual effect between the EC and acetate buffer, which improved the permeability of the film. In contrast, the release of drug in HCl solution was dependent on the HPC levels. Increasing the levels of HPC increased the effects of hydrogen ions on the polymer of HPC, which resulted in a lower viscosity and strength of the gel, forming the larger size of pores in polymer films, thus increasing the drug diffused from the coating film. Further findings in phosphate buffer showed a reduction in the drug release compared to that in other media, which was only sensitive to the osmolarity rather than the HPC level and pH of the buffer. Additionally, a mathematical theory was used to better explain and understand the experimentally measured different drug release patterns. In summary, the study revealed that the effects of the media overcompensated that of the drug solubility to some extent for controlled-release of the coating polymers, and the drug release mechanism in multiple media depend on EC and HPC rather than on HPC alone, which may have a potential to facilitate the optimization of ideally film-coated formulations.

Preparation, Characterization and In Vitro / In Vivo Evaluation of Oral Time-Controlled Release Etodolac Pellets

The objective of this study was to prepare time-controlled release etodolac pellets to facilitate drug administration according to the body's biological rhythm, optimize the drug's desired effects, and minimize adverse effects. The preparation consisted of three laminal layers from center to outside: the core, the swelling layer, and the insoluble polymer membrane. Factors influenced the core and the coating films were investigated in this study. The core pellets formulated with etodolac, lactose, and sodium carboxymethyl starch (CMS-Na) were prepared by extrusion-spheronization and then coated by a fluidized bed coater. Croscarmellose sodium (CC-Na) was selected as the swelling agent, and ethyl cellulose (EC) as the controlled release layer. The prepared pellets were characterized by scanning electron microscopy and evaluated by a dissolution test and a pharmacokinetic study. Compared with commercial available capsules, pharmacokinetics studies in beagle dogs indicated that the prepared pellets release the drug within a short period of time, immediately after a predetermined lag time. A good correlation between in vitro dissolution and in vivo absorption of the pellets was exhibited in the analysis.

Development of Novel High Density Gastroretentive Multiparticulate Pulsatile Tablet of Clopidogrel Bisulfate Using Quality by Design Approach

Myocardial infarction, i.e., heart attack, is a fatal condition which is on the increase all over the world. It is reported that a large number of heart attack occur in morning hours which are attributable to platelet aggregation. Chronotherapy at this stage can be crucial. Clopidogrel bisulfate (CLB) is an antiplatelet agent and has become a drug of choice for prevention of heart attack. It is soluble in acidic pH and has a narrow absorption window. So, its long residence time in stomach is desirable. Therefore, a novel high density tablet was developed comprising multiparticulate pellets with pulsatile release necessary to maintain chronotherapy of heart attack. The pellets were prepared by extrusion-spheronization and coated in fluidized bed processor with different coating material to achieve pulsatile release. The size, shape of pellets, and drug release were evaluated. High density tablet containing coated pellets was formulated and evaluated for retention in stomach. Quality by design tools was used to design and optimize the processes. Timed release observed by dissolution study showed lag time of 6 h followed by burst release of drug up to 94% in 1 h. Density of tablets was found to be 2.2 g cm^-3 which is more than gastric fluid. In vivo x-ray studies in rabbit revealed 8 h of gastric retention of tablet at the bottom of the stomach. Thus, CLB high density pulsatile system looks to open up a window of opportunity for developing formulations with drugs that are stable in gastric region and needed chronotheraupetic activity.