Bimetallic Metal-Organic Framework Derived Metal-Carbon Hybrid for Efficient Reversible Oxygen Electrocatalysis

Hetero-Diatomic CoN4-NiN4 Site Pairs with Long-Range Coupling as Efficient Bifunctional Catalyst for Rechargeable Zn-Air Batteries

In this study, Co/Ni-NC catalyst with hetero-diatomic Co/Ni active sites dispersed on nitrogen-doped carbon matrix is synthesized via the controlled pyrolysis of ZIF-8 containing Co2+ and Ni2+ compounds. Experimental characterizations and theoretical calculations reveal that Co and Ni are atomically and uniformly dispersed in pairs of CoN4-NiN4 with an intersite distance ≈0.41 nm, and there is long-range d-d coupling between Co and Ni with more electron delocalization for higher bifunctional activity. Besides, the in situ grown carbon nanotubes at the edges of the catalyst particles allow high electronic conductivity for electrocatalysis process. Electrochemical evaluations demonstrate the superior ORR and OER bifunctionality of Co/Ni-NC catalyst with a narrow potential gap of only 0.691 V and long-term durability, significantly prevailing over the single-atom Co-NC and Ni-NC catalysts and the benchmark Pt/C and RuO2 catalysts. Co/Ni-NC catalyzed Zn-air batteries achieve a high specific capacity of 771 mAh g-1 and a long continuous operation period up to 340 h with a small voltage gap of ≈0.65 V, also much superior to Pt/C-RuO2.

Construction of a 3D Metal-Organic Framework and Its Composite for Water Remediation via Selective Adsorption and Photocatalytic Degradation of Hazardous Dye

In this work, a new bimetallic Na(I)-Zn(II) metal-organic framework (MOF), formulated as [Na₂Zn₃(btc)₂(μ-HCOO)₂(μ-H₂O)₈] _n (1) (H₃btc = benzene tricarboxylic acid), and its composite (ZnO@1) have been successfully synthesized using solvothermal and mechanochemical solid grinding methods. 1 and ZnO@1 were characterized by diffraction [single-crystal X-ray diffraction (XRD) and powder XRD], spectroscopic (ultraviolet-visible diffuse reflectance spectroscopy and Fourier transform infrared spectroscopy), microscopic (transmission electron microscopy), and thermal (thermogravimetric analysis) methods. The surface area and porosity of 1 were determined using a Brunauer-Emmett-Teller analyzer. Single-crystal diffraction of 1 confirms that Na1 and Zn2 have octahedral coordination environments, whereas Zn1 has a tetrahedral coordination geometry. Topological simplification of 1 shows a 3,6-connected kgd net. Na(I)-Zn(II) MOF (1) is crystallized with slight porosity and exhibits good tendency toward the encapsulation of zinc oxide nanoparticles (ZnO NPs). The photocatalytic behaviors of 1 and its composite (ZnO@1) were investigated over MB dye under sunlight illumination with promising degradation efficiencies of 93.69% for 1 and 97.53% for ZnO@1 in 80 min.

Optimization of Sulfurization Process of Cobalt Sulfide and Nitrogen Doped Carbon Material for Boosting the Oxygen Reduction Reaction Catalytic Activity in Alkaline Medium

In order to reduce fuel cell material cost and promote its application, it is urgent to develop non-noble metal materials to replace platinum as the cathode catalysts in fuel cells. The cobalt sulfide and nitrogen co-doped carbon (S-Co-N/C) materials with metal-organic frameworks as precursors have shown good oxygen reduction reaction (ORR) catalytic activity. Benefiting from the protection of catalytic active sites by sulfur atoms, the stability and alcohol-tolerance of the S-Co-N/C catalyst can be significantly improved. In order to fully understand the effect of the sulfurization process on the properties of the material, zeolite imidazole frameworks (ZIF)-8, and ZIF-67 are used as precursors to prepare a novel material of S-Co-N/C by using a sulfurization-pyrolysis method. Another S-Co-N/C material by using a pyrolysis- sulfurization method is prepared for comparison. The effects of the sulfurization process in the preparation on the morphology, chemical structure, specific surface area, and ORR catalytic activity of the final material are investigated. The experimental results show that the surface of the S-Co-N/C material tends to be rough due to the sulfurization reaction of the metal elements. The porosity of the material is reduced to some extent due to the remaining Zn elements in the final product. Interestingly, some carbon nanotubes are found to be generated on the surface of the S-Co-N/C material because of the synergistic effect of Zn and Co on the carbon material during the pyrolysis process, which is beneficial to accelerate the adsorption of oxygen on the S-Co-N/C surface and the electron transportation during the oxygen reduction reaction. In addition, the generated CoS during the sulfurization process can further protect the Co elements from agglomeration, which can effectively increase the ORR catalytic active sites in the final material. The S-Co-N/C material prepared by the sulfurization-pyrolysis method performs a superior ORR catalytic activity to the one synthesized by the pyrolysis-sulfurization method.