Targeted Metagenomics of Retting in Flax: The Beginning of the Quest to Harness the Secret Powers of the Microbiota

Identification of new potential molecular actors related to fiber quality in flax through Omics

One of the biggest challenges for a more widespread utilization of plant fibers is to better understand the different molecular factors underlying the variability in fineness and mechanical properties of both elementary and scutched fibers. Accordingly, we analyzed genome-wide transcription profiling from bast fiber bearing tissues of seven different flax varieties (4 spring, 2 winter fiber varieties and 1 winter linseed) and identified 1041 differentially expressed genes between varieties, of which 97 were related to cell wall metabolism. KEGG analysis highlighted a number of different enriched pathways. Subsequent statistical analysis using Partial Least-Squares Discriminant Analysis showed that 73% of the total variance was explained by the first 3 X-variates corresponding to 56 differentially expressed genes. Calculation of Pearson correlations identified 5 genes showing a strong correlation between expression and morphometric data. Two-dimensional gel proteomic analysis on the two varieties showing the most discriminant and significant differences in morphometrics revealed 1490 protein spots of which 108 showed significant differential abundance. Mass spectrometry analysis successfully identified 46 proteins representing 32 non-redundant proteins. Statistical clusterization based on the expression level of genes corresponding to the 32 proteins showed clear discrimination into three separate clusters, reflecting the variety type (spring-/winter-fiber/oil). Four of the 32 proteins were also highly correlated with morphometric features. Examination of predicted functions for the 9 (5 + 4) identified genes highlighted lipid metabolism and senescence process. Calculation of Pearson correlation coefficients between expression data and retted fiber mechanical measurements (strength and maximum force) identified 3 significantly correlated genes. The genes were predicted to be connected to cell wall dynamics, either directly (Expansin-like protein), or indirectly (NAD(P)-binding Rossmann-fold superfamily protein). Taken together, our results have allowed the identification of molecular actors potentially associated with the determination of both in-planta fiber morphometrics, as well as ex-planta fiber mechanical properties, both of which are key parameters for elementary fiber and scutched fiber quality in flax.

Effect of Warm-Water Retting Pretreatment on the Physical Properties of Banana Stem and Its Fibre

In this paper, warm-water flax retting was used as a pretreatment method for banana-fibre extraction. To determine the optimum conditions for flax retting, the physical properties of various parts of stems and fibres in the process of flax retting were analysed. By studying the tensile strength, elongation at break, diameter, moisture regain, and other characteristics of the fibres, the influences of bacteria and enzymes in the retting liquor on the fibre characteristics in different retting stages were determined. Through mechanical-property tests and microscopic observation of the stem skin, the change rules of the mechanical properties and degumming state of the stems were examined. The results showed that the fibre tensile strength of banana stems reached the maximum value of 45 ± 16 cN·tex^-1 after 11 days of retting. As most resins had not been hydrolysed, fibre extraction was difficult. After 21-25 days of retting, the tensile strength of fibres was about 34 ± 10 cN·tex^-1, elongation at break was about 1.71%, and moisture regain was about 13.56%. The fibre characteristics met the process requirements, and the tensile separation stress of the stem was small, about 0.034 MPa. This time point could be used as the optimum endpoint for retting flax in warm water, which could provide theoretical support and research basis for the recycling of banana straw. The functional groups of the extracted fibres were studied by FTIR, which confirmed the observed change rule of each component during degumming. The experimental results showed that a longer retting time corresponded with a lower content of fibre impurities, more thorough degumming, and less difficult extraction; however, strength and toughness decreased.

Hemp Fibre Properties and Processing Target Textile: A Review

Over the last several decades, Cannabis sativa L. has become one of the most fashionable plants. To use the hemp potential for the development of a sustainable textile bio-product sector, it is necessary to learn about the effect of the processes creating hemp’s value chain on fibre properties. This review presents a multi-perspective approach to industrial hemp as a resource delivering textile fibres. This article extensively explores the current development of hemp fibre processes including methods of fibre extraction and processing and comprehensive fibre characteristics to indicate the challenges and opportunities regarding Cannabis sativa L. Presented statistics prove the increasing interest worldwide in hemp raw material and hemp-based bio-products. This article discusses the most relevant findings in terms of the effect of the retting processes on the composition of chemical fibres resulting in specific fibre properties. Methods of fibre extraction include dew retting, water retting, osmotic degumming, enzymatic retting, steam explosion and mechanical decortication to decompose pectin, lignin and hemicellulose to remove them from the stem with varying efficiency. This determines further processes and proves the diversity of ways to produce yarn by employing different spinning systems such as linen spinning, cotton and wool spinning technology with or without the use of the decortication process. The aim of this study is to provide knowledge for better understanding of the textile aspects of hemp fibres and their relationship to applied technological processes.

Investigations by AFM of Ageing Mechanisms in PLA-Flax Fibre Composites during Garden Composting

PLA-flax non-woven composites are promising materials, coupling high performance and possible degradation at their end of life. To explore their ageing mechanisms during garden composting, microstructural investigations were carried out through scanning electron microscopy (SEM) and atomic force microscopy (AFM). We observe that flax fibres preferentially degrade 'inwards' from the edge to the core of the composite. In addition, progressive erosion of the cell walls occurs within the fibres themselves, 'outwards' from the central lumen to the periphery primary wall. This preferential degradation is reflected in the decrease in indentation modulus from around 23 GPa for fibres located in the preserved core of the composite to 3-4 GPa for the remaining outer-most cell wall crowns located at the edge of the sample that is in contact with the compost. Ageing of the PLA matrix is less drastic with a relatively stable indentation modulus. Nevertheless, a change in the PLA morphology, a significant decrease in its roughness and increase of porosity, can be observed towards the edge of the sample, in comparison to the core. This work highlights the important role of intrinsic fibre porosity, called lumen, which is suspected to be a major variable of the compost ageing process, providing pathways of entry for moisture and microorganisms that are involved in cell wall degradation.