Clap-and-Fling Mechanism in Non-Zero Inflow of a Tailless Two-Winged Flapping-Wing Micro Air Vehicle

Structural response and mechanical properties of the hind wing of the beetle Protaetia brevitarsis

The folding/unfolding mechanism and collision recovery effect of the beetle's hind wings can provide biomimetic inspiration for the optimization of wing deplorability and the investigation of collision prevention recovery mechanism of new amphibious morphing vehicle. In this study, a method is described to investigate the structural response and mechanical properties of the hind wings of the beetle Protetia brevitarsis under natural conditions. The specially processed test samples were conducted to tensile testing, which facilitates the evaluation of the mechanical properties of specific areas of the hind wing. The micro geometric morphological characteristics of the cross-section of the specimen after tensile fracture were observed by scanning electron microscopy. The three-dimensional morphology of the ventral and dorsal sides of the hind wing was characterized using three-dimensional scanning and reverse modeling methods. The finite element model of the hind wing is developed to investigate the structural deformation and modal response characteristics of its flapping. The uniformly distributed load on the hind wing surface is derived from the lift characteristics obtained from the computational fluid dynamics simulation of flapping wing motion. RESEARCH HIGHLIGHTS: Scanning electron microscope is used to observe the cross-sectional characteristics of the veins and membranes. The material properties of the wing membranes and veins of the hind wings were measured using the tensile testing system. The three-dimensional morphology of the hind wing was characterized using 3D scanning and reverse modeling methods. The finite element model of the hind wing is developed to investigate the structural deformation and modal response characteristics of its flapping.

A Retrospective of Project Robo Raven: Developing New Capabilities for Enhancing the Performance of Flapping Wing Aerial Vehicles

Flapping Wing Air Vehicles (FWAVs) have proven to be attractive alternatives to fixed wing and rotary air vehicles at low speeds because of their bio-inspired ability to hover and maneuver. However, in the past, they have not been able to reach their full potential due to limitations in wing control and payload capacity, which also has limited endurance. Many previous FWAVs used a single actuator that couples and synchronizes motions of the wings to flap both wings, resulting in only variable rate flapping control at a constant amplitude. Independent wing control is achieved using two servo actuators that enable wing motions for FWAVs by programming positions and velocities to achieve desired wing shapes and associated aerodynamic forces. However, having two actuators integrated into the flying platform significantly increases its weight and makes it more challenging to achieve flight than a single actuator. This article presents a retrospective overview of five different designs from the "Robo Raven" family based on our previously published work. The first FWAVs utilize two servo motors to achieve independent wing control. The basic platform is capable of successfully performing dives, flips, and button hook turns, which demonstrates the potential maneuverability afforded by the independently actuated and controlled wings. Subsequent designs in the Robo Raven family were able to use multifunctional wings to harvest solar energy to overcome limitations on endurance, use on-board decision-making capabilities to perform maneuvers autonomously, and use mixed-mode propulsion to increase payload capacity by exploiting the benefits of fixed and flapping wing flight. This article elucidates how each successive version of the Robo Raven platform built upon the findings from previous generations. The Robo Raven family collectively addresses requirements related to control autonomy, energy autonomy, and maneuverability. We conclude this article by identifying new opportunities for research in avian-scale flapping wing aerial vehicles.

Numerical Simulations of the Effect of the Asymmetrical Bending of the Hindwings of a Hovering C. buqueti Bamboo Weevil with Respect to the Aerodynamic Characteristics

The airfoil structure and folding pattern of the hindwings of a beetle provide new transformation paths for improvements in the aerodynamic performance and structural optimization of flapping-wing flying robots. However, the explanation for the aerodynamic mechanism of the asymmetrical bending of a real beetle's hindwings under aerodynamic loads originating from the ventral and dorsal sides is unclear. To address this gap in our understanding, a computational investigation into the aerodynamic characteristics of the flight ability of C. buqueti and the large folding ratio of their hindwings when hovering is carried out in this article. A three-dimensional (3D) pressure-based SST k-ω turbulence model with a biomimetic structure was used for the detailed analysis, and a refined polyhedral mesh was used for the simulations. The results show that the fluid around the hindwings forms a vortex ring consisting of a leading-edge vortex (LEV), wing-tip vortex (TV) and trailing-edge vortex (TEV). Approximately 61% of the total lift is generated during the downstroke, which may be closely related to the asymmetric bending of the hindwings when they are subjected to pressure load.