Utilization of Er:YAG Laser in Retrieving and Reusing of Lithium Disilicate and Zirconia Monolithic Crowns in Natural Teeth: An In Vitro Study

Effect of Er,Cr: YSGG laser debonding treatment on the optical properties and surface roughness of ceramic laminate veneers: An in vitro study

PURPOSE

The objective of this study was to evaluate the effect of (Er,Cr: YSGG) laser debonding treatment on optical properties and surface roughness of veneers made of different ceramic materials.

MATERIALS AND METHODS

Thirty bovine incisors were prepared to receive laminate veneers and divided into three groups (n = 10) according to ceramic material where group (E): IPS e.max CAD, group (S): Vita Suprinity, and group (C): Celtra Duo. Blocks were sectioned into 0.5 mm thickness plates and cemented on the labial surface of incisors using resin cement. The Er,Cr: YSGG laser was applied to each specimen at 4.5 W and 25 Hz for group E and at 6 W and 25 Hz for groups S and C. Color change (△E00), translucency parameter (TP) and surface roughness in µm (Ra) values were measured and calculated before and after laser treatment. Data were analyzed using two-way mixed model ANOVA at a significance level of p < 0.05.

RESULTS

The highest mean △E00 value was recorded in group E (1.35 ± 0.09) followed by group S (1.08 ± 0.16) and then group C (0.93 ± 0.10) with a significant difference between them (p < 0.001). All groups exceeded the perceptibility threshold but remained below the acceptability threshold. No statistically significant difference was found in TP except for group E (p = 0.019). Ra values after laser debonding showed significantly higher values than before laser treatment in all three groups (p < 0.001).

CONCLUSION

Er,Cr: YSGG laser can be safely used for debonding ceramic veneers without altering the optical properties but it does increase the roughness of debonded ceramic restorations.

Laser debonding of ultrathin occlusal veneers fabricated from different CAD/CAM ceramic materials

BACKGROUND

Erbium lasers safely offer the possibility of reuse for debonded restorations. Since these lasers have a high affinity for water molecules, they are absorbed by resin cement causing explosive ablation of the cement and thus, the restoration debonds. The efficiency of this process depends on many factors, including the ceramic type, its chemical composition and thickness. Therefore, this study was designed to test the time taken to debond ultrathin occlusal veneers made of three types of milled ceramic materials and evaluate the integrity of these restorations after debonding.

METHODS

Three ceramic types were evaluated in this study: lithium disilicate (IPS Emax CAD), highly condensed lithium disilicate (GC initial®LiSi), and translucent zirconia (Katana zirconia STML). Each group consisted of 8 occlusal veneers of 0.5 mm thickness. The samples were cemented to the occlusal surfaces of the upper molar teeth. An Er; Cr: YSGG laser was applied to the occlusal veneers using the scanning method, and time until debonding was calculated. The debonded samples were then inspected under a stereomicroscope for possible damage. Numerical data are presented as the mean with 95% confidence interval (CI), standard deviation (SD), minimum (min.) and maximum (max.) values. Normality and variance homogeneity assumptions were confirmed using Shapiro-Wilk's and Levene's tests, respectively. Data were normally distributed and were analyzed using one-way ANOVA followed by Tukey's post hoc test. The significance level was set at p < 0.05 for all tests. Statistical analysis was performed with R statistical analysis software version 4.3.2 for Windows (R Core Team (2023). R: A language and environment for statistical computing. R Foundation for Statistical Computing, Vienna, Austria. URL https://www.R-project.org/).

RESULTS

There was no significant difference in debonding time between the different materials (p = 0.995). The longest debonding time was found for Katana STML (87.52 ± 20.45) (seconds), followed by Emax (86.94 ± 20.63) (seconds), while the lowest value was found for LiSi initial (86.14 ± 25.16) (seconds). In terms of damage to the debonded veneers, The Emax and zirconia samples showed no damage. However, 40% of the LiSi samples fractured during debonding, and 20% exhibited cracks. Only 40% of the LiSi samples were sound after debonding.

CONCLUSION

Er; Cr: YSGG laser can be used efficiently to remove ceramic occlusal veneers. However, its effect on LiSi restorations needs further research.

Er:YAG laser settings for debonding zirconia restorations: An in vitro study

This in vitro study aimed to determine the optimal frequency and energy settings for debonding zirconia restorations using an erbium-doped yttrium aluminum garnet (Er:YAG) laser. A total of 200 zirconia specimens (5 mm × 5 mm × 1.5 mm) were fabricated from two types of materials: (1) 3 mol% yttria oxide stabilized tetragonal zirconia polycrystalline (3Y-TZP) and (2) 5 mol% yttria oxide stabilized tetragonal zirconia polycrystalline (5Y-TZP). The zirconia specimens were bonded to dentin using resin cement (RelyX Ultimate, 3 M) and divided into 20 groups based on their laser treatments (n = 5). Er:YAG laser treatment was applied at various frequencies (10 Hz and 20 Hz) and energies (80 mJ, 100 mJ, 120 mJ, 140 mJ, 160 mJ, 180 mJ, 200 mJ, 220 mJ, 240 mJ, and 260 mJ). The time required to debond the specimens and the temperature changes that dentin underwent during the laser treatment were recorded. The surface morphologies of the debonded dentin and zirconia specimens were observed using scanning electron microscopy (SEM). Additional zirconia specimens were fabricated for 4-point flexural strength testing and surface roughness measurements. Statistical analyses were conducted using three-way analysis of variance (ANOVA) and Student-Newman-Keuls (SNK)-q tests (α = 0.05). The debonding time of each specimen varied between 4.8 and 160.4 s, with an average value of 59.2 s. The dentin temperature change for each specimen ranged from 2.3 to 3.6 °C, with an average value of 2.7 °C. The debonding time was significantly influenced by the zirconia material type and laser energy, but it was not affected by the laser frequency. Among the specimens, those made of 3Y-TZP needed significantly more time for debonding than 5Y-TZP. The optimal energies were 220 mJ for 3Y-TZP and 200 mJ for 5Y-TZP. The laser frequency, laser energy, and type of zirconia material had no effect on the dentin temperature change. Additionally, no surface alternations were observed on the dentin or zirconia materials after laser treatment. The surface roughness and flexural strength of the zirconia materials remained unchanged after laser treatment. In summary, Er:YAG laser treatment effectively and safely removes zirconia restorations without impacting their mechanical properties, with a safe temperature change of less than 5.6 °C. The optimum frequency and energy settings for debonding 3Y-TZP and 5Y-TZP restorations were found to be 10/20 Hz and 220 mJ and 10/20 Hz and 200 mJ, respectively.

Erbium laser-assisted ceramic debonding: a scoping review

PURPOSE

Removal of ceramic restorations and appliances can be time consuming, invasive, and inconvenient. Erbium lasers offer an alternative noninvasive method for debonding of ceramic appliances. This paper aims to provide a comprehensive review of current literature on the effectiveness of erbium lasers for removal of ceramic restorations and appliances from natural teeth and dental implants.

METHODS

A comprehensive search of 7 databases, including Medline (Ovid), Embase, Dentistry and Oral Sciences Source (DOSS), Web of Science, Cochrane Library, and ProQuest Dissertations and Theses was performed. The inclusion and exclusion criteria were agreed prior to the literature search. Two reviewers independently screened the title and abstract. A third reviewer then broke the tie, if any. The selected articles then underwent full text review and the data was extracted.

RESULTS

The search identified 4117 unique articles published through June 10, 2021. Studies were assessed and categorized based on the type of restoration/appliance, type of abutment, type of laser, laser settings, efficacy of debonding, and pulpal temperature rise. Thirty-eight full-text articles were reviewed for inclusion. Time for ceramic debonding varies depending on the type of restorations and materials. Removal of zirconia crowns from teeth and implant abutments requires a longer period of time compared to lithium disilicate crowns. Temperature increases were reported as 5.5 degrees or less. Laser setting and laser type affect the debonding time and the increase in temperature. Examinations of debonded ceramics demonstrated no known structural damages resulting from laser applications.

CONCLUSIONS

Erbium lasers are effective noninvasive tools to remove all ceramic restorations/appliances from natural teeth and implant abutments without causing harm to abutments. Laser-assisted debonding should be considered as a viable alternative to rotary instrumentation for ceramic crowns; however, clinical studies of erbium-assisted ceramic retrieval are needed.

In Vitro Study of Laser-Assisted Prefabricated Ceramic Crown Debonding as Compared to Traditional Rotary Instrument Removal

This study compared the laser and rotary removals of prefabricated zirconia crowns in primary anterior and permanent posterior teeth. Sixty-two extracted teeth were prepared for prefabricated zirconia crowns cemented with resin-modified glass-ionomer cement. Specimens underwent crown removals by a rotary handpiece, or erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser. Pulpal temperatures, removal times, and scanning electron microscopy (SEM) examinations were compared. The average crown removal time for rotary and laser methods was 80.9 ± 19.36 s and 353.3 ± 110.6 s, respectively, for anterior primary teeth; and 114.2 ± 32.1 s and 288.5 ± 76.1 s, respectively, for posterior teeth (p < 0.001). The maximum temperature for the rotary and laser groups was 22.2 ± 8.5 °C and 27.7 ± 1.6 °C for anterior teeth, respectively (p < 0.001); and 21.8 ± 0.77 °C and 25.8 ± 0.85 °C for the posterior teeth, respectively (p < 0.001). More open dentinal tubules appeared in the rotary than the laser group. The rotary handpiece removal method may be more efficient than the laser with lower pulpal temperature changes. However, the laser method does not create noticeable tooth or crown structural damage compared to the rotary method.

Photobiomodulation Therapy in the Treatment of Oral Mucositis—A Case Report

In 2021, our group published a laboratory study on the impact of PBM on human gingival fibroblasts. The in vitro results confirmed the fact that the appropriately selected wavelength and properly selected parameters of the laser settings can increase cell proliferation, modulate inflammatory markers, and decrease the susceptibility of human gingival fibroblasts to apoptosis. Therefore, this case report was aimed at the clinical evaluation of the proposed settings and treatment regimen in a very difficult situation of an immunocompromised patient with extensive changes and stagnation of symptoms for many weeks. A 65-year-old man, during his oncological treatment, was diagnosed with oral mucositis grade 3 according to the World Health Organization and National Cancer Institute scales. Due to pain sensation, long-lasting and not healing oral lesions, and problems with solid food intake, he was qualified for laser photobiomodulation therapy. For the management of oral lesions, a diode laser 635 nm (Smart^MPro, Lasotronix, Poland) was intraorally applied at an energy density of 4 J/cm², the 20 s of irradiation, the output power of 100 mW, and in continuous wave mode. Seven treatment procedures were performed two times a week using the spot technique in contact and non-contact mode. Within 21 days of monotherapy, all ailments disappeared. The patient was also able to reuse dental dentures and return to a solid diet. The obtained results confirm the efficiency of at least 3 PBM protocols. Our case shows that the use of PMB therapy contributes to faster healing of painful oral lesions in oncological patients, and thus the treatment time and return to the appropriate quality of life is shorter.

SEM Evaluation of Tooth Surface after a Composite Filling Removal Using Er:YAG Laser, Drills with and without Curettes, and Optional EDTA or NaOCl Conditioning

(1) Background: This study aimed to evaluate the microporosity of the tooth surface structure adjacent to the cemento-enamel junction (CEJ) after the removal of composite fillings with a drill in comparison with removal by an Er:YAG laser and after cleaning with a periodontal curette, chemical EDTA and NaOCl (sodium hypochlorite) conditioning. (2) Methods: The research material consisted of 30 extracted premolars with cervical composite fillings. The teeth were divided into six groups according to the method of tooth preparation: group G1 (n = 5)-a diamond drill; group G2 (n = 5)-a diamond drill + curette; group G3 (n = 5)-a diamond drill + 24% EDTA (PrefGel, Straumann, Switzerland); group G4 (n = 5)-an Er:YAG laser (LightWalker, Fotona, Ljubljana, Slovenia) set with the following parameters: power: 1.65 W (composite removal, CR), 1.2 (tooth conditioning, TC), energy: 110 mJ (CR), 80 mJ (TC), frequency: 15 Hz, pulse duration: 50 μs, tip diameter: 1 mm, air/fluid cooling: 4, distance 1.5 mm, energy density: 14.01 J/cm2 (CR), 10.19 J/cm2 (TC); group G5 (n = 5)-an Er:YAG laser + 2% sodium hypochlorite (NaOCl); group G6 (n = 5)-an Er:YAG laser + 5.25% NaOCl. In each tooth, three cavities were made and subjected to analysis. The dentin surface was evaluated using a scanning electron microscope (SEM). (3) Results: Groups G1 and G2 exhibited mechanical damage to the tooth surface structure caused by the rotary motion of a diamond drill. The SEM image showed a smear layer that could only be removed chemically using 24% EDTA gel (group G3). The tooth surfaces prepared with the Er:YAG laser (groups G4-G6) revealed a homogeneous structure without damage along with open dentinal tubules (without smear layer) and visible denaturation of collagen fibers. The sodium hypochlorite (NaOCl) conditioning did not increase the visibility of dentinal tubules. (4) Conclusions: Dentin surfaces have open dentinal tubules after removal of the composite filling using the Er:YAG laser and therefore do not require additional NaOCl conditioning.

The Effect of Er:YAG Lasers on the Reduction of Aerosol Formation for Dental Workers

Infection prevention in dental practice plays a major role, especially during the COVID-19 pandemic. This study aimed to measure the quantity of aerosol released during various dental procedures (caries and prosthetic treatment, debonding of orthodontic brackets, root canal irrigation) while employing the Er:YAG lasers combined with a high-volume evacuator, HVE or salivary ejector, SE. The mandibular second premolar was extracted due to standard orthodontic therapy and placed in a dental manikin, to simulate typical treatment conditions. The particle counter was used to measure the aerosol particles (0.3–10.0 μm) at three different sites: dental manikin and operator’s and assistant’s mouth area. The study results showed that caries’ treatment and dental crown removal with a high-speed handpiece and the use of the SE generated the highest aerosol quantity at each measured site. All three tested Er:YAG lasers significantly reduced the number of aerosol particles during caries’ treatment and ceramic crown debonding compared the conventional handpieces, p < 0.05. Furthermore, the Er:YAG lasers generated less aerosol during orthodontic bracket debonding and root canal irrigation in contrast to the initial aerosol quantity measured in the dental office. The use of the Er:YAG lasers during dental treatments significantly generates less aerosol in the dental office setting, which reduces the risk of transmission of viruses or bacteria.

Retrieval of Prefabricated Zirconia Crowns with Er,Cr:YSGG Laser from Primary and Permanent Molars

(1) Background: Prefabricated zirconia crowns are used to restore teeth in children. The purpose of this study was to evaluate the removal of these crowns with the erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser; (2) Methods: A total of 12 primary and 12 permanent teeth were prepared and prefabricated zirconia crowns were passively fitted and cemented with two resin modified glass-ionomer (RMGI) cements. Surface areas of prepared teeth and crowns were calculated. Crowns were removed using two laser settings: 4.5 Watts, 15 Hertz, 20 water/20 air, and 5 Watts, 15 Hertz, 50 water/50 air. The retrieval time and temperature changes were tested recorded. Data were analyzed using ANOVA with Tukey’s adjusted post hoc pairwise comparison t-test; (3) Results: The average time for crown removal was: 3 min, 47.7 s for permanent; and 2 min 5 s for primary teeth. The mean temperature changes were 2.48 °C (SD = 1.43) for permanent; and 3.14 °C (SD = 1.88) for primary teeth. The time to debond was significantly positively correlated with tooth inner surface area and volume, outer crown volume, and the cement volume; (4) Conclusions: Use of the Er,Cr:YSGG laser is an effective, safe and non-invasive method to remove prefabricated zirconia crowns cemented with RMGI cements from permanent and primary teeth.